HE60ANZ Garage Door Opener Installation and Operating Instructions
Contents
1. 21 INSTALL THE PROTECTOR SYSTEM See accessories Install this accessory for all installations on canopy doors one piece door with horizontal and vertical track doors over 2 5m and when the closing force as measured on the bottom of the door is over 400N 40kg i i plete Se a ad ee ath L Whilst Chamberlain have engineered safety features into Instructions are included with this accessory fee es PA B The Protector System provides an additional i Mi icountries these devices are compulsory to prevent seri i ere of ea ag ie a small sit shea ern ious injury or property damage For an Ae peace ofi under a garage door It uses an invisible beam which iv i ue i when broken by an obstruction causes a closing door to Mind and the Saleh alee pleaseinstallthisinexpen open and prevents an open door from closing and is sive safety device strongly recommended for homeowners with young children Note The opener will automatically detect the Protector System when it is installed and operating for 5 minutes during this time the beams must remain unobstructed The opener will not close unless the beams are aligned Connecting the Protector System white black wires twisted together Locate the terminals on the front of the opener Strip all wires back about 102. 14 FASTEN DOOR BRACKET Sectional and One Piece Door Installation Procedure Door bracket 1 has left and right side fastening holes If your installation requires top and bottom fastening holes use both the door bracket and door bracket plate 2 as shown Centre door bracket with or without door bracket plate as required at the top inside face of door as shown Mark holes A One piece doors Locate bracket at inside face of the door 0 100mm down B Sectional door a 150 250mm below the top of the door Fasten bracket to the door using the appropriate la screws A 0 100mm A Wooden doors B 150 250mm Drill 8mm holes 5 16 and fasten the door bracket with nut lock washer and carriage bolt 3 B Sheet metal doors Fasten with wood screws 4 C One piece door option Fasten with wood screws 4 15 HANG OPENER Bend hanging brackets 1 so they are flat against ceiling Measure distance from header bracket to ceiling mounting bracket bolts Mark length on ceiling starting at the header wall along this point is where the unit will be mounted Lift door to full open position rest opener on door Insert square head screws A into rail assembly B approximately 120mm from end of rail near motor unit Slide hanging brackets on to square head screws and secure brackets with nuts 5 In this process the square head screws hook into slots on the sides of rail by turning 90 C
3. 15 MAINTAENANCE OF YOUR OPENER 15 TROUBLE SHOOTING 16 SPECIFICATIONS 00 00 16 WARRANTY eec2cdiwseeside be ceooe araia 17 E DOOR TYPES A Sectional Door with Curved Track B One Piece_Door with Horizontal Track Only Max door height 2 125m Max door width 3 5m NOTE Unit will not work with One Piece Doors with out Horizontal and Vertical Tracks Double Wing Doors or Canopy Doors CER 10mm 8mm 4 5mm 4mm Li an GD a 11 13mm 11mm 13mm EX HARDWARE PROVIDED ASSEMBLY HARDWARE 1 Square head screws 8mm carriage bolt Cable pulley Pin 8mm lock nut Pulley bracket 6mm nut Concrete anchor 6mm lag bolt 10 6mm self threading screw 11 6mm hex bolt 12 Wire clips 13 Hex screws 14 C rail bracket 15 Clevis pin 16 Ring fastener 17 Flat washer 18 Anchor 19 Insulated staples iO 7 BEFORE YOU BEGIN Look at the wall or ceiling above the garage door The header bracket must be securely fastened to structural supports Do you have a finished ceiling in your garage If so a support bracket and additional fastening hardware not supplied may be required Do you have an access door in addition to the garage door If no
4. For concrete ceilings drill 8mm pilot holes into ceiling and insert concrete anchors 2 Secure hanging brackets to ceiling with lag screws 3 For wood ceilings drill 4mm pilot holes and secure with lag screws 3 Optional A second set of hanging brackets is recommended when door is very heavy The hanging brackets should be located ih the first third to the centre of the rail upwards the most during the travel y gt S A S TANA w o a s o 5 5S5 9 9 HJ ATTACH EMERGENCY RELEASE ROPE amp HANDLE Thread one end of rope 1 through hole in top of red handle so NOTICE reads right side up as shown 3 Secure with an over hand knot 2 Knot should be at least 25mm 1 from end of the rope to prevent slipping Thread other end of rope through hole in release arm of the outer trolley 4 Adjust rope length so that handle is less than 1 8m 6 feet above the floor Secure with an overhand knot NOTE If it is necessary to cut rope heat seal cut end to prevent fraying Door should be released in the closed position if possible To Release the trolley PULL down on the red handle DO NOT USE THE HANDLE TO OPEN OR CLOSE THE DOOR OBJECTS INCLUDING MOTOR VEHICLES WITHIN THE DOORWAY The door is under significant tension T DO NOT DISENGAGE THE OPENER TO MANUAL OPERATION WITH CHILDREN PERSONS OR OTHER and if the door has dev
5. BACKLIT DOOR CONTROL BUTTON OR THE OPTIONAL MULTI FUNCTION DOOR CONTROL PANEL of the reach of children Mount at least 1 5 m 5 feet above the floor Serious personal injury from a moving garage door may result from misuse of opener Do not allow children to operate the door control or transmitter Permanently fasten the caution label to the wall near the door control as a reminder of safe operating pro cedures f Locate door control where the garage door is visible away from door and door hardware and out There are 2 screw terminals 1 on the back of the door control 2 Strip about 6mm of insulation from bell wire 4 Separate wires enough to connect the white red wire to terminal screw 1 and the white wire to terminal screw 1 Backlit door control button Fasten to an inside garage wall with sheet metal screws 3 provided with backlit push button Drill 4mm holes and use anchors 6 if installing into drywall or concrete A convenient place is beside the service door and out of reach of children Multi function door control optional Insert a small flat head screwdriver into the top of the wall control 10 gently pry the cover off Fasten to an inside garage wall with sheet metal screws 8 as follows Install bottom screw allowing 3mm to protrude from the wall Position bottom of door control over screw head and adjust for snug fit Install top screw with care to avoid cracking plastic housing Do not over tighte
6. binding call for professional garage door service e Check to be sure door opens and closes fully Adjust limits and or force if necessary Twice a year e Check chain tension Disconnect trolley first Adjust if necessary Once a year e Oil door roller bearings and hinges The opener does not require additional lubrication Do not grease the door tracks TROUBLE SHOOTING 1 Opener doesn t operate from remote e Does the opener have electric power Plug lamp into outlet If it doesn t light check the fuse box or the circuit breaker Some outlets are controlled by a wall switch Have you disengaged all door locks Review installation instruction warning on page 1 Try a new battery If you have two or more remotes and only one operates refer wireless programming section 21 Is there a build up of ice or snow under door The door may be frozen to ground Remove any obstruction The garage door spring may be broken Have it profession ally replaced Remote has short range Is battery installed Try a new one Change the location of the transmitter in the car The metal garage door foil backed insulation or metal sid ing will reduce the transmission range Door reverses for no apparent reason and opener lights don t blink Is something obstruction the door Pull manual release handle Operate door manually If it is unbalance or binding call for professional garage door service Reprogram the force Clear any ice or
7. distributor CONTACT DETAILS Chamberlain service centres Australia Phone toll free 1800 638 234 Fax toll free 1800 888 121 www homentry com au New Zealand Auckland phone 09 477 2823 Phone toll free 0800 653 667 Fax toll free 0800 653 663 www homentry co nz 114A3370D 18 2010 The Chamberlain Group Inc
8. locks con nected to the garage door before installing the door opener Installation and wiring must be in compliance with your local building and electrical codes The safety reverse system test is very impor tant Your garage door MUST reverse on contact with a 40mm obstacle placed on the floor Failure to properly adjust the opener may result in serious personal injury from a closing garage door Repeat the test once a month and make any necessary adjustments This opener should not be installed in a damp or wet space exposed to weather This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervi sion or instruction concerning use of the appliance by a person responsible for their safety PrPrr PR gt The Protector System must be used for all installations where the closing force as meas ured on the bottom of the door is over 400N 40kgf Excessive force will interfere with the prop er operation of the Safety Reverse System or dam age the garage door After installation ensure that the parts of the door do not extend over public footpaths or roads Install the wireless wall control or any additional wall control in a location where the garage door is visible at a height of at least 1 5m and out of the reach of children Do not allow children to operate push button s or tr
9. snow from garage floor area where garage door closes i a reverses in fully closed position adjust the close imit Repeat safety reverse test after adjustment is complete The need for occasional adjustment of the Limit positions is normal Weather conditions in particular can affect door travel 4 Door reverses for no apparent reason and door control button light blinks for 5 seconds after reversing Check The Protector System if you have installed this accessory if the light is blinking correct alignment 5 The garage door opens and closes by itself Keypad or Code Switch transmitters only Is there a neigh bor with a garage door opener using the same code Change your code Make sure remote push button is not stuck in ON position 6 Door does not close completely Adjust the close limit Repeat safety reverse test after any adjustment of door arm length or close limit 7 Door opens but won t close Check The Protector System if you have installed this accessory If the light is blinking correct alignment si re the safety reverse test after the adjustment is com plete 8 Opener light does not turn on Replace light bulb 21 Watts maximum 9 Opener light does not turn off Defective logic board 10 Opener motor hums briefly then won t work Garage door springs are broken Close door and use man ual release rope and handle to disconnect trolley Open and close door manually A properly balanced door will stay i
10. 15 minute cooling period after 5 continuous operations of the opener The opener light will turn on 1 when opener is initially plugged in 2 when the power is interrupted 3 when the opener is activated CARE OF YOUR OPENER When properly installed opener will provide high performance with a minimum of maintenance The opener does not require additional lubrication Limit and force adjustments These adjustments must be checked and properly set when Pa is installed Only a screwdriver is required to adjust the limits Weather conditions may cause some minor change ments particularly during the first year of operation Refer to the limit and force adjustments sections 18 amp 19 Fo the instructions carefully and repeat the safety reverse test after any adjustment anges in the door operation requiring some readus ow Transmitter Additional remotes can be purchased at any time for use in all vehicles using garage Refer to accessories The receiv er must be programmed to operate with any new remote transmitter battery If transmission range decreases replace battery To change battery Insert batteries positive side up To replace cover snap shut along both sides Do not dispose of the old battery with household waste Take batteries to a proper disposal centre MAINTENANCE OF YOUR OPENER Once a month e Repeat safety reverse test Make any necessary adjustments e Manually operate door If it is unbalanced or
11. Determine the position of the close limit switch 1 long wire by aligning the centre of trolley and the centre of the limit switch The limit switches are actuated by a magnet in the inner trolley Insert bottom tab 5 of limit switch 1 into bottom lip of rail 7 Insert top tab 4 under top lip of rail 6 Lift limit assembly against top lip of rail and tignten screw 8 to secure close limit switch Open garage door by hand to the full open position Pull red handle to afsendage door past inner trolley Determine HE eoswen of the open limit switch 3 short wire by aligning the centre of the trolley and the centre of the limit switch Insert bottom tab 5 of limit switch a into bottom lip of rail 7 Insert top tab 4 under top lip of rail 6 Lift limit assembly against top lip of rail and tighten screw 8 to secure open limit switch Insert wires for limit switch 9 into top channel of rail 10 Secure wires with wire clip the wires must be secured so they do not interfere with the travel of the trolley Re engage trolley then activate transmitter the opener will operate and reconnect to the door automatically Run opener 2 full travel cycles If the door reverses in mid travel go to setting the force section Adjust limit switch es as necessary to fully open and close the door without reversing 19 SETTING THE FORCE The force is programmed to operate most doors however if limits are not able to be set or the door
12. FOMENT RY www homentry com au HE60ANZ Garage Door Opener Installation and Operating Instructions Owners Copy Please keep these instructions for future reference This manual contains IMPORTANT SAFETY information DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY N2966 START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS WARNING Failure to comply with the following instructions may result in serious personal injury or property damage Read and follow all instructions carefully The garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the instructions in this manual oo PPP PPP BP These safety alert symbols mean WARNING A possible risk to personal safety or property damage exists Keep garage door balanced Do not let the garage door opener compensate for a binding or sticking garage door Sticking binding or unbal anced doors must be repaired before installing this opener Do not wear rings watches or loose clothing while installing or servicing a garage door opener Frequently examine the door installation in par ticular cable springs and mountings for signs of wear damage or imbalance Do not use if repair or adjustment is needed since springs and hardware are under extreme tension and a fault can cause serious personal injury To avoid serious personal injury from entangle ment remove all ropes chains and
13. OT over tighten INSTALLATION SECTION A Wear protective goggles when working overhead to protect your eyes from injury Disengage all existing garage door locks to avoid damage to the garage door To avoid serious personal injury from entanglement remove all ropes connected to the garage door before installing the opener lt is recommended that the opener be installed 2 1m 7 feet or more above the floor where space permits 11 POSITION THE HEADER BRACKET The header bracket must be rigidly fastened to a struc tural support of the garage Reinforce the wall or ceil ing with a 40mm 1 1 2 board if necessary Failure to comply may result in improper operation of safety reverse system You can attach the header bracket either to the header wall 1 or to the ceiling 3 Follow the instructions which will work best for your particular requirements With the door closed mark the vertical centreline 2 of the garage door Extend line onto header wall above the door Open door to highest point of travel Draw an intersecting horizontal line 4 on header wall 50mm or 200mm above high point to provide travel clearance for top edge of the door height depends on door type refer section 15 12 INSTALL THE HEADER BRACKET NOTE Refer to vertical centre and horizontal lines Ea in step 11 for proper placement of header racket A Wall Mount Centre the header bracket Ww on the vert
14. ae during normal operation follow this proce ure Locate the program button 1 on the left side panel of unit 2 Push the program button twice to enter unit into auto force adjustment mode The green LED will flash slowly Activate unit with remote and run the unit to the open limit Activate unit again to run the unit to the closed limit The door must travel through a complete cycle up and down in order for the force to be set properly If the unit stops before it reaches the open or close limit repeat the process The green LED will stop flashing when the force has been learned BJ TEST THE SAFETY REVERSE SYSTEM obstacle laid flat on the floor Failure to properly adjust opener may result in seHeus personal The safety reverse system test is important Garage door must reverse on contact with a 40mm A injury from a closing garage door Repeat test once a month and adjust as needed Procedure Place a 40mm obstacle 1 laid flat on the floor under the garage door Operate the door in the down direction The door must reverse on_the obstruction If the door stops on the obstruction it is not traveling far enough in the down direction Move Close Limit closer to door When the door reverses on the 40mm obstacle remove the obstruction and run the opener through a complete travel cycle Door must not reverse in closed position If it does adjust limit and repeat safety reverse test KEEP THESE INSTRUCTIONS
15. ansmitter s Serious personal injury from a closing garage door may result from misuse of the opener Permanently fasten the Warning Labels in Prominent Places adjacent to Wall Controls and manual release mechanisms as a reminder of safe operating procedures Activate opener only when the door is in full view free of obstructions and the opener is properly adjusted No one should enter or leave the garage while the door is in motion Do not allow children to play near the door or door controls Disconnect electric power to the garage door opener before making repairs or removing cov ers KEEP THESE INSTRUCTIONS NOTE If your garage has no service entrance door a AML1702 outside quick release must be installed This accessory allows manual operation of the garage door from outside in case of power failure CONTENTS PAGE SAFETY INSTRUCTIONS 1 DOOR TYPES fsccniad beware dan is 2 TOOLS REQUIRED 2 HARDWARE PROVIDED 2 BEFORE YOU BEGIN 3 COMPLETED INSTALLATION 3 ASSEMBLY irere e aroha oe dvarcd 3 5 INSTALLATION 0 00 00004 5 8 CONNECT ELECTRIC POWER 8 ADJUSTMENT 22 02200 0 ees eae eee eee 9 INSTALL PROTECTOR SYSTEM WIRELESS PROGRAMMING INSTALL DOOR CONTROL 13 ACCESSORIES 05 14 REPLACEMENT PARTS 14 OPERATION OF YOUR OPENER 15 CARE OF YOUR OPENER
16. ct arising out of any exclu sion set out below we may charge you a fee to repair and or return the Unit to you Exclusions This warranty does not cover any failure of the Unit due to 1 non compliance with the instructions regarding installation operation maintenance and testing of the Unit or of any prod uct with which the Unit is used 2 any attempt to repair dismantle reinstall or move the Product to another location once the Product is installed by any person other than an authorised installer 3 tampering neglect abuse wear and tear accident electrical storm excessive use or conditions other than normal domestic use This warranty does not cover any problems with or relating to the garage door or garage door hardware including but not limited to the door springs door rollers door alignment or hinges any problems caused by electrical faults replacement of batteries or light bulbs or labour charges for reinstalling a repaired or replaced Units 17 Liability Australia only Under no circumstances shall the Seller be liable for conse quential incidental or special damages arising in connection with the use or inability to use the Unit In no event shall the Seller s liability for damages or injury arising from breach of law or contract or for negligence exceed the cost of repairing or replacing the Unit or refunding the purchase price of the Unit Under Division 2 Part V of the Trade Practices Act 1974 c
17. eloped a fault or incorrect tension it may be unsafe and may fall rapidly CONNECT DOOR ARM TO TROLLEY A Preferred Installation Disconnect trolley by pulling on the red handle and slide towards door With door closed connect straight door arm 5 to trolley 4 with bolt 3 secure with nut 1 Connect curved door arm 2 to door bracket with bolt 3 secure with nut 1 Align straight and curved door arms with a 2 hole overlap connect with bolt 3 secure with nut 1 If straight door arm 5 is too long cut the end of the door arm Where extra travel distance is required With door closed connect curved door arm 2 to door bracket with bolt 3 secure with nut 1 Lift curved door arm 2 to meet trolley connect door arm to trolley with bolt 3 secure with nut 1 To avoid installation difficulties do not run the garage door opener until instructed to do so Plug the opener into electric outlets as specified by local wiring codes The opener light will turn on when power is connected and remain on for 2 1 2 minutes f Connect Electric Power fer 18 ATTACH LIMIT SWITCHES NOTE The limits must be installed as shown If installed incorrectly the unit will not function properly Close garage door by hand
18. er tain warranties and conditions Implied Terms are implied into contracts for the supply of goods or services if the goods or services are of a kind ordinarily acquired for personal domes tic or household use or consumption Liability for breach of those Implied Terms cannot be excluded or limited and the limitations and exclusions above do not apply to the Implied Terms Except for the Implied Terms and the warranties set out above the Seller excludes all warranties and conditions implied by statute at law in fact or otherwise Liability New Zealand only Except as set out in the Fair Trading Act 1986 and the Consumer Guarantees Act 1993 a all other guarantees warranties and representations in relation to the Unit or its supply are excluded to the extent that the Seller can lawfully exclude them and b under no circumstances shall the Seller be liable for con sequential incidental or special damages arising in connection with the use or inability to use the Unit other than those which were reasonably foreseeable as liable to result from the failure NOTE We request that you attach your sales docket or invoice to this manual to enable you to establish the date of purchase in the unlikely event of a service call being made Chamberlain reserves the right to change the design and specification without prior notification Some features or accessories may not be available in certain markets or areas Please check with your
19. he following devices The transmitter Hold the push button down until the door starts to move e The backlit door control button if you have installed this accessory Hold the button down until door starts to move e The outside keyswitch or keyless entry system if you have installed either of these accessories Opening the door manually Door should be fully closed if possible Weak or broken springs could allow an open door to fall rapidly Property damage or serious personal injury could result The door can be opened manually by pulling the release handle down To reconnect the doorpull the handle up and toward the opener the trolley will re eengage upon operation activate the unit Do not use the manual release handle to pull the door open or closed When the opener is activated by transmitter or door control button If fully open the door will close If closed the door will open If opening or closing the door will stop If partially open the door will move in the opposite direction of last travel If an obstruction is encountered while closing the door will reverse to the open position If an obstruction is encountered while opening the door will reverse for 1 second The optional Protector System uses an invisible beam which when broken by an obstruction causes a closing door to open and prevents an open door from closing It is STRONGLY RECOMMENDED for homeowners with young children Allow a
20. ical centre line 2 with the bottom edge of the header bracket on the horizontal line 4 with the arrow pointing toward the ceiling Mark all of the header bracket holes 5 Drill 4 5 mm 3 16 pilot holes and fasten the header bracket with wood screws 3 Ceiling Mount Extend vertical centre line 2 onto the ceiling Centre the header bracket 1 on the ver tical mark no more than 150 mm 6 from the wall Make sure the arrow is pointing toward the opener Mark all of the header bracket holes 5 Drill 4 5 mm 3 16 pilot holes and fasten the header bracket with wood screws 3 For concrete ceiling mount use concrete anchors 6 provided Clearance between highest point of travel and rail should not exceed 50mm and can be zero when clearance between door and ceiling is only 30mm 13 ATTACH RAIL TO HEADER BRACKET Position the opener on the floor below the mounting bracket using some packaging material to protect the unit s cover Raise the rail the holes in the header sleeve and the holes of the header to align bracket Use the clevis pin 1 provided to join the two pieces then insert the fastening ring 2 to secure in place Note To enable the rail to clear sectional door springs it may be necessary to lift the opener onto a temporary support The opener must secured in place by means of a support or by being held by another person
21. mm then twist the two white wires and the two white black wires together Trim the twisted wires to approximately 6mm Use a small screwdriver or pen to hold down the spring terminals insert the white black wires into the grey terminal 4 then termi nate the white only wires into the white terminal 3 white grey A WIRELESS PROGRAMMING should enter or leave garage while door is in motion Do not allow children to operate push but Activate the opener only when door is in full view free of obstruction and properly adjusted No one A ton s or remote s Do not allow childen to play near the door Your garage door opener receiver and transmitter are set to a matching code If you purchase additional transmitters the garage door opener must be programmed to accept the new remote code To program receiver to match additional remote control codes 1 Press and hold down the transmitter button you wish to program to the opener 1 2 Press and release the program button on the side of the opener 2 3 When the opener light blinks It has learned the code If the light bulb is not installed two clicks will be heard To erase all codes from motor unit memory or to deactivate any unwanted remote first erase all codes Press and hold the program button 2 on opener until the learn indicator light goes out approximately 6 seconds All previous c
22. n e Replace cover by inserting bottom tabs 9 and snapping into place To remove cover after mounting gently pry at top with paper clip or small flat head screwdriver Run the bell wire up the wall and across the ceiling to the garage door opener Use insulated staples 5 to secure wire The opener quick connect terminals 7 are located in the recess next to the learn button on the left side panel Insert bell wire into holes in the quick connect terminals as follows red white to red and white to white E NY 3 Ghr s BJ ACCESSORIES 1 Model 84335AML 3 channel mini transmitter 3 channel transmitter Wireless keyless entry keypad Model 770AML The Protector System IR Beams Model 845AML Multi function door control panel Model 75AML Backlit door control button Model 760AML Outside keyswitch Model 1702AML Outside quick release REPLACEMENT PARTS 041A5644 Trolley with chain cable assy 041A5674 2 Head only 041A5643 Hardware bag 012B0905 Door bracket 012B0906 Door bracket 012C0788 Header bracket 012C0908 Rail end piece 041A5675 Rail hardware 041A5676 Rail sections 041A5644 Bed Gp 04107108 041A5674 012B0905 AS 01280906 D 012C0908 b 041A5675 we Ce 041C0521 1 012C0788 041A0079 OPERATION OF YOUR OPENER Your opener can be activated by any of t
23. n any point of travel while being supported entirely by its springs If it does not call for a professional garage door service to correct the problem If problem occurs on first operation at opener door may be locked Disable door lock Opener won t activate due to power failure Pull manual release handle to disconnect trolley Door can be opened and closed manually The next time opener is activated the trolley will reconnect The outside quick release accessory 1702AML if fitted dis connects the Trolley from outside the garage in case of power failure opener Use insulated staples 5 to secure wire The opener Quick Connect Terminals 7 are located in the recess next to the learn button on the left side panel Insert bell wire into holes in the Quick Connect Terminals as follows Red White to Red and White to White 11 16 a Door reverses after the force adjustment was complet ed Watch rail if it bends or swings If so see section 19 Door is very heavy and or in bad condition Call for profes sional garage door service 13 Rail bends respectively rail swings a lot Use additional hanging brackets for the rail Garage door is very heavy or in bad condition Call for pro fessional garage door service 14 Do I need to use the additional hanging brackets Avoids bending or swinging of rail 15 Opener light flares When the garage door is very heavy or isn t balanced have door serviced 16 Opener overides o
24. n your proof of purchase in the unlikely event you require warranty service If during the limited warranty period the Unit fails due to defects in materials or workmanship Chamberlain will provided the defective part or Unit is returned freight and insurance pre paid and well packaged to the nearest Chamberlain office or authorised installer undertake to repair or at its option replace any defective part or Unit and return it to the Buyer at no cost Repairs and replacement parts are warranted for the remaining portion of the original warranty period Limited warranty on motor Chamberlain will furnish a replacement motor free of charge if it is found to be defective Labour costs may apply Where the Unit has been installed by an authorised installer Chamberlain will furnish replacement parts free of charge through the authorised installer A service fee for on site serv ice may apply In warranty service During the warranty period if the product appears as though it may be defective call our toll free service before removal of the unit A Chamberlain technician will diagnose the problem and promptly supply you with the parts for do it yourself repairs or provide you with shipping instructions for a factory repair or replacement If an authorised installer installed your unit you must call them for prompt on site service If our service centre determines that a warranty claim has been made in respect of a failure or defe
25. ne of the light swtiches Limit switches are not installed at the correct side of the rail and or in the location refer attach limit switch section 18 A functional test of the rail contact cable can be made with a simple household magnet Check condition of cables for insulation damages Check if the magnet located inside the inner trolley is in place SPECIFICATIONS Input Voltage 230 VAC 50 60 Hz Max Pull force 600N Rated Power Input 85 Watts Rated Load 3 0 Nm Standby Power 9 Watts Max Door Weight 60kg Motor Type ss passes mete enetd 63 1 Worm Gear Reduction VOS gicdgadwouehe es 24VDC Drive Mechanism Length of Travel 2 3M Travel Rate 8cm sec PAM o se ccsis dee A 24V 21 Watts Safety Electronic Auto Force Adjustment ElectriGall spicier dies Thermal Fuse in Transformer Limit Adjustment Manual Dimension Length Overall 2 75m Headroom Required 30mm Hanging Weight 10kg Receiver Code Registers Rolling Code Operating Frequency 433 92MHz CHAMBERLAIN 2 YEAR LIMITED WARRANTY HomEntry HE60ANZ Garage Door Opener Chamberlain Australia Pty Limited Chamberlain New Zealand Limited Seller warrants to the original purchaser of the Home Entry HE60ANZ Garage Door Opener Unit that it is free from defects in material and or workmanship for a period of 2 years from the date of first purchase from the Seller Please retai
26. nsert pulley into bracket NOTE Make sure the bracket is assembled a ponon shown Slide pin 5 through holes in cable pulley bracket and cable pulley NOTE Trolley with magnet 6 MUST be installed in the position shown INSERT CHAIN CABLE INTO RAIL Slide cable pulley bracket 1 into rail assembly 3 be sure to insert cable pulley bracket as shown Push cable pulley bracket toward front of rail and slide inner trolley 2 into rail assembly Magnet 4 MUST be installed in position shown or unit will not function properly EI ATTACH TROLLEY TO RAIL Turn rail assembly over Slide outer trolley 1 pine rail assembly 2 be sure the ad a door arm hole 3 is heading in direction of oor 4 Slide outer trolley down rail until it engages with inner trolley 9 ATTACH RAIL TO UNIT Turn rail assembly over and wrap chain around drive sprocket 1 Slide rail assembly 2 toward unit and into slots on top of unit Attach C Bracket 3 on the rail and secure with screws 4 as shown Push cable pulley bracket forward making chain tight on sprocket Chain MUST engage teeth on drive sprocket KJ ATTACH HEADER BRACKET Turn rail and unit assembly over Slide cable pulley bracket 2 toward front end of rail 3 Be careful chain does not come off drive sprocket on unit or become twisted ay carriage bolt 5 into header bracket Secure with lock nut 4 Tighten nut until chain does not droop below rail Do N
27. odes are now erased Reprogram each trans mitter or keyless entry you wish to use 11 JKE YLESS DEVICE PROGRAMMING OPTIONAL ACCESSORIES one should enter or leave garage while door is in motion Do not allow children to operate push button s or remote s Do not allow children to play near the door 1 Activate the opener only when door is in full view free of obstruction and properly adjusted No NOTE Your new keyless entry must be pro grammed to operate your garage door open er Program the receiver to match additional transmitter code Using the LEARN button 1 Press and release the learn button 1 on opener The learn indicator light will glow steadily for 30 seconds 2 Within 30 seconds enter a four digit person al identification number PIN of your choice on the keypad 2 then press and hold the ENTER button 3 Release the button when the opener light blinks 3 It has learned the code If the light bulb is not installed two clicks will be heard NOTE This method requires two people if the keyless entry is already mounted out side the garage Using the multi function door control 1 Enter a four digit personal identification num ber PIN of your choice on the keypad then press and hold ENTER 2 While holding the ENTER button press and hold the LIGHT button on the multi function door control 3 Continue holding the ENTER and LIGHT but t
28. ons while you press the push bar on the multi function door control all three buttons are held 4 Release buttons when the opener light blinks It has learned the code If the light bulb is not installed two clicks will be heard i r n 5 Slide the Cover plate Wireless fingerprint access system C379 Til up A optional accessory Full instruction are available with this accessory Once you have enrolled your user into the C379 you G Swipe finger at can program the unit into your opener jej steady speed B Using the LEARN button 1 Press and release the learn button 1 on opener The learn indicator light will glow steadily for 30 sec asa aa mae pais re Yellow LED will indicate 2 Within 30 seconds slide the cover of the C379 up H successful swipe C as illustrated A Swipe your finger on the reader A head at a steady speed B until the yellow LED turns on C 3 When the opener light blinks It has learned the code If the light bulb is not installed two clicks will Test reader by pressing be heard ensure there are no obstructions in the YX Je path of the door then press the send button D to the send button D test the door 24 REPLACE LIGHT BULB Replace light bulb 1 with a 21 watt maximum light bulb Insert bulb into socket The light will turn on and remain lit for 2 1 2 minutes when power is connected After 2 1 2 minutes it will turn off TS is 25 WIRING THE
29. t Model 1702AML outside quick release acces sory is required 4 COMPLETED INSTALLATION ALL PARTS LISTED ARE SUPPLIED IN THE CARTON As you proceed with the assembly installation and adjustment procedures in this manual you may find it help ful to refer back to this illustration of a completed installation 1 Cable pulley bracket 2 Trolley 3 Chain cable assembly 4 Rail 5 Hanging bracket 6 Power cord 7 Opener 8 Light lens 9 Manual release rope amp handle 10 Door arm 11 12 Door bracket Header bracket E ASSEMBLE RAIL Place rail pieces 1 on a flat surface for assembly Take special note of the raised_line on the rail pieces 4 these lines MUST line up in order for the rail to fit together properly All three rail sections are interchangeable Slide rail braces 2 into slots on the sides of rail Make sure small tabs on rail braces 3 are up against top lip of rail Connect rail by sliding other end of braces into next rail Be sure the raised lines that run down rail sections 4 line up Tap rail assembly 5 on a piece of wood 6 until rail sections are flush Repeat for final rail section 6 ASSEMBLE CABLE PULLEY BRACKET Insert carriage bolt 1 through square hole in cable pulley bracket 4 Remove chain cable assembly 3 from carton Wrap cable around cable pulley 2 and i
Download Pdf Manuals
Related Search