Electrician Installation Manual National Warranty Line
Contents
1. avoid pinching wires Tighten down rod pin screw Secure down rod with the other shorter down rod screw provided d Slide on canopy cover and refit the ball joint If an extension rod needs to be installed please go to page 9 STEP 2 Fig 2 a Drill a hole in the timber nogging for wiring b Use the two hex screws to secure the hanger bracket onto the timber nogging The timber nogging should be supplied by the installing electrician and must be supported between the two ceiling joists as shown in the diagram above STEP 3 Fig 3 a TIGHTEN THE GRUB SCREW This is important to ensure the fan will not wobble and the weight of the fan is supported b Hang the ball joint into the hanger bracket Ensure the groove on the hanger bracket is locked into the slot on the ball joint 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If WARNING only one blade is damaged you are still required to replace with a new set HUNTER PACIFIC Electrician Installation Manual Icon Ceiling Fan IN TERNATIONAL Assembling the fan STEP 4 Fig 4 amp 5 a Connect wires from the fan with wires in the ceiling via the terminal block on the hanger bracket refer to2. such as T hooks are available for certain types of installation After installation fan blades must be at least 2 1 m 7 feet above floor level The use of these products by children and the infirm must be under supervision IF THERE ARE ANY PROBLEMS WITH THE PRODUCT AT TIME OF INSTALLATION THE INSTALLER MUST CONTACT THE WARRANTY HOT LINE NUMBER 1300 360 280 BEFORE LEAVING THE JOB SITE PLEASE DO NOT REMOVE THE FAN FROM THE CEILING ONCE INSTALLED UNLESS INSTRUCTED TO DO SO HUNTER PACIFIC Electrician Installation Manual Icon Ceiling Fan IN TERNATIONAL Parts List Icon Fan _ Hanger Bracket B Hex Head Screw Ball Joint ee Canopy Cover Motor Housing i Base Plate Blade Screw Qty ree i erase 2 Down Rod Pin Screw these parts come preassembled Down Rod Short Screw HUNTER PACIFIC INTERNATIONAL Electrician Installation Manual Icon Ceiling Fan Assembling the fan Ball Joint Canopy Cover BS Conn ction Collar ih Ps Wy Motor Housing a SS Fig 1 a R NS _4 Down Rod Pin Screw Hanger Timber Nogging Bracket STEP 1 Fig 1 PERFORM THIS STEP IF THE WIRES HAVE NOT BEEN FED THROUGH THE DOWN ROD a Loosen the ball joint screw and remove the ball joint pin to separate the down rod from the ball joint b Feed wires from motor housing up and through the down rod c Insert the down rod pin screw through the connection collar and the down rod
3. a Fit the compact fluorescent light to the a Turn the light to lock it to the light socket light socket b Gently push the glass cover upwards and turn it to attach the glass cover to the fan 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If WARNING only one blade is damaged you are still required to replace with a new set 8 HUNTER PACIFIC Electrician Installation Manual Icon Ceiling Fan IN TERNATIONAL Attaching an accessory light kit E14 Light 2 x 40W STEP 1 Fig 17 Slightly push the base plate upward and turn until tabs unlock to remove it STEP 2 Fig 18 a Using the connectors on the wires attach the light wires from the motor housing to the light wires on the light assembly b Attach and secure the light assembly kit using the 3 screws provided c Install light globes into the light sockets STEP 3 Fig 19 a Once globes are installed the glass cover can be fitted on to the fan b Gently push the glass cover upwards and turn it to attach the glass cover to the fan 4 Glass Cover 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use
4. with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If WARNING only one blade is damaged you are still required to replace with a new set 9 HUNTER PACIFIC Electrician Installation Manual Icon Ceiling Fan IN TERNATIONAL Attaching an extension rod Hunter Pacific rods to be used ONLY Ball Joint _ _ a i F Loosen a Ball Joint Screw Down Rod Step 2 Fig 21 Loosen the ball joint screw take out the ball joint pin and remove the ball joint Then slide off the Step 1 Fia 20 Canopy Cover Loosen and remove the down rod screws and the down rod pin screw to remove the standard down rod from the motor housing Down Rod Ball Joint Pin _ Ball Joint Tighten Ball Joint Screw Down Rod a Step 3 Fig 22 amp 23 Now install the extension rod and reverse step 1 amp 2 to secure the rod to the fan and the ball joint NOTE If the extension rod needs to be shortened cut the rod to the required length and drill the appropriate hole size to fit the ball joint pin The cut end of the rod should be used at the ball joint end only When installing a 1 8m extension rod the wiring will need to be extended and joined This should be done using crimp style connectors 1 Do not attempt to operate the fan or optional light kit with any wa
5. Check wires in the terminal block are connected properly connection wires should be stripped back at the connection point and unused wires should be sealed and capped off Check that the reversing switch is pushed into its Summer or Winter position Fan is not corresponding to the remote control Check for flat battery Make sure the dipswitch settings in the hand piece and the remote receiver for the same fan correspond Fan is wobbling Check the ball joint slot is locked into the hanger bracket groove Make sure blades are a matched set the letters on matching sets of blades should be identical with the numbers varying within 3 grams of each other Check blade screws are tightened firmly If necessary use balancing kit provided to settle the wobble Fan is noisy WARNING Check all screws and parts are secured firmly Ensure there are no loose parts moving inside the motor housing Make sure the fan is installed with a Hunter Pacific wall controller only do not use solid state controllers as they can cause unpleasant motor noises National Warranty Line 1300 360 280 Monday to Friday from 9am to 5pm EST Only available within Australia Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty Do not mix blade sets from one fan to another as
6. HUNTER PACIFIC Electrician Installation Manual Icon Ceiling Fan IN TERNATIONAL eon FA NOTE The Icon light fitting does not come standard however it can be bought as an accessory item CEILING FAN MUST BE INSTALLED BY A LICENSED ELECTRICIAN NO OTHER PERSONS SHOULD ATTEMPT TO INSTALL THIS FAN Electricians are recommended to tick off all items on the quick checklist and fill out their details onto the back page of the Fan Owner Warranty amp Operations Manual after installation ELECTRICIANS TO PROTECT YOUR CUSTOMER S WARRANTY PLEASE READ PAGE 2 OF THIS BOOKLET PRIOR TO THE INSTALLATION OF THIS PRODUCT National Warranty Line 1300 360 280 Monday to Friday from 9am to 5pm EST Only available within Australia Hunter Pacific International Pty Ltd Building 8 256 New Line Road Dural NSW 2158 Australia ABN 18 063 521 666 HUNTER PACIFIC Electrician Installation Manual Icon Ceiling Fan IN TERNATIONAL IMPORTANT INFORMATION ELECTRICIANS MUST READ PRIOR TO INSTALLATION 1 Distributor and installer details and purchase receipts are essential for on site warranty claims and must be presented to repair personnel make sure you record your details in the Fan Owner Warranty and Operations Manual 2 Fans and fixed wiring products must only be installed by persons who are appropriately licensed by the applicable State regulatory body Therefore to protect our repair personnel on site warranty claims will not be accep
7. an is operating correctly on all three speeds using the wall control ler If light is installed Check light switch is functioning properly If remote control is installed Check the fan and light if installed is responding to the remote control correctly Write Dip switch code in user guide If remote control is installed Check where possible a separate isolation switch has been installed for the fan Check electrician s details have been recorded onto the back page of the Owner s Operations and Warranty Manual 12
8. ate controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set 12 HUNTER PACIFIC Electrician Installation Manual Icon Ceiling Fan INTERNATIONAL Quick Checklist Electricians make sure everything on this checklist is ticked off before you leave the installation site If you have trouble installing our product please refer to the trouble shooting section on the previous page first then phone the Hunter Pacific Warranty Line on 1300 360 280 open 9am to 5pm EST DO NOT uninstall the fan and DO NOT return fan to retailer 1 10 Ceiling fan is not installed to a solid state wall controller Neither leading nor lagging edge controllers will give satisfactory performance Wall controllers must only be types approved for use by Hunter Pacific International The fan optional fan light and bracket is earthed Fan and optional fan light are run from the same final circuit Mounting bracket must be firmly secured to a solid structure such as a concrete ceiling steel structure or timber framing If additional bracing is added it must be firmly secured to the rafters and not left floating on the ceiling Special mounts such as T hooks are available for certain types of installation Fan blades are at least 2 1m feet above floor level Check the f
9. e it STEP 2 Fig 11 a Use the connectors to attach the light wires from the motor housing to the light assembly kit b Attach and secure the light assembly kit using the 3 screws provided c Plug the light globe into the socket DO NOT touch the light globe with your fingers It is important to keep the globe clean or it will fail pre maturely STEP 3 Fig 12 Gently push the glass cover upwards and turn to attach the light glass to the fan a Tab Slots To Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set 7 HUNTER PACIFIC Electrician Installation Manual Icon Ceiling Fan IN TERNATIONAL Attaching an accessory light kit GX 53M 14W compact fluorescent light STEP 1 Fig 13 a Slightly push the base plate upward and turn until tabs unlock to remove it STEP 2 Fig 14 a Using the connectors on the wires connect the light wire from the motor housing with the light wires on the light assembly b Attach and secure the light assembly kit using the 3 screws provided p Screws PEREN Glass Cover Light STEP 3 Fig 15 STEP 4 Fig 16
10. figure 4 and 5 b Make sure earth wires are also connected c Connect light wires red white if a light fitting is going to be used Cap seal light wires if a light fitting is not going to be used eo Green yellow Oo r rab f x z O 2 2 S Z D Combi Separate 5 Control Control FA LAE N 8 Separate terminal Fan Wiring Wiring for use with 3 pole block For when 3 pole Colours representative only block is fitted Separate terminal required for active for light when 3 pole block fitted STEP 5 Fig 6 a Slide canopy up and over the hanger bracket b Twist the canopy to locate screws holes then loosen canopy screws half way c Now twist the canopy to the opposite direction and fully tighten screws until the canopy is stabilised Hanger Bracket Down Rod 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If WARNING only one blade is damaged you are still required to replace with a new set 5 HUNTER PACIFIC INTERNATIONAL Assembling the fan STEP 7 Fig 8 a Once all blades are attached to the motor housing refit the base The tabs should lock in to place ensuring the base plate is sec
11. ll control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If WARNING only one blade is damaged you are still required to replace with a new set 10 HUNTER PACIFIC Electrician Installation Manual Icon Ceiling Fan INTERNATIONAL Trouble Shooting Tips Fan Fan will not start Check that the reversing switch is pushed into its Summer or Winter position Check wire connections in the wall switch and terminal blocks ensure all wires are making proper contact If it is a Typhoon fan check and ensure the reversing switch plate under the switch cover is not bent also check the 3 wires coming from the switch plate are straight Occasionally the switch plate may get bent during transportation this allows the switch cover to press against the plate and stop the fan from working If it is a Typhoon fan check the nine pin plug under the switch cover is properly connected and the colours on the plug are corresponding If it is a concept fan and it has an external start up capacitor check that this external capacitor is properly connected Fan speed is not corresponding to the wall controller Check the speeds on the wall controller has been wired correctly and are making proper contact Brown speed 1 Purple speed 2 Red speed 3
12. ted if products have been installed by unlicensed persons 3 Damage caused by incorrect installation force majeure electrical surges lightning power grid fluctuations water or by connection to alternative power supply sources such as solar inverters etc is not eligible for warranty repair 4 Blades must be replaced only as a complete set Blades are supplied only as a pre balanced set and the replacement of individual blades may void the warranty by causing mechanical damage to the motor excessive noise or premature wear 5 When products are installed in a location requiring special access equipment Such as scaffolding or scissor lifts etc the cost of providing installing and operating special access equipment must be borne by the site owner For safety and to protect your customers warranty the following must be taken into account when installing and operating the product s a DO NOT USE SOLID STATE WALL CONTROLLERS Neither leading nor lagging edge controllers will give satisfactory performance Wall controls must only be types approved for use by Hunter Pacific International The fan light and bracket must be earthed Fan and light must be run from the same final circuit Mounting bracket must be firmly screwed to a solid structure such as a concrete ceiling steel structure or timber framing If additional bracing is added it must be firmly secured to the rafters and not left floating on the ceiling Special mounts
13. this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set 11 HUNTER PACIFIC Electrician Installation Manual Icon Ceiling Fan INTERNATIONAL WARNING Trouble Shooting Tips Light Light will not turn on Make sure globe has not blown and it is properly fit ted between the metal prongs Check all light wires in the light kit the terminal block in the canopy cover and the wall switch have been connected together correctly Light is not corresponding to remote control Make sure globe has not blown and it is properly fitted between the metal prongs Check all light wires in the light kit the terminal block in the canopy cover and the wall switch have been connected together correctly Check dip switch settings in remote hand piece and remote receiver correspond Light wires appear to be missing or too short Wires may be stuck in the motor housing Carefully pull wires out of the motor housing careful not to strip the wires as this may cause the fan to short Light flickers or flashes Check globe is secured between the metal prongs in the light kit Make sure you are using the globes specified National Warranty Line 1300 360 280 Monday to Friday from 9am to 5pm EST Only available within Australia 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid st
14. urely attached to the motor housing WARNING Reverse _ Electrician Installation Manual Icon Ceiling Fan STEP 6 Fig 7 a Slightly push the base plate upward and turn anticlockwise until tabs unlock to remove it b Once the base plate is removed the internal blade carriers will be exposed Insert blades and attach them to the motor housing as shown in figure 8 c Tighten the 3 blade screws firmly but do not over tighten d Install blades for each fan individually Base Plate STEP 8 Fig 9 a Reverse switch should be in the down position for Summer fan spins anticlockwise and in the up position for Winter fan spins clockwise b Make the sure reverse switch is not stuck in its neutral position otherwise the fan will not spin Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set 6 HUNTER PACIFIC Electrician Installation Manual Icon Ceiling Fan INTERNATIONAL Attaching an accessory light kits 78 mm halogen light MAX 100W WARNING SN J STEP 1 Fig 10 a Slightly push the base plate upward and turn until tabs unlock to remov
Download Pdf Manuals
Related Search