Home

DAS DL100 - Theft Prevention

Contents

1. If tone dialling is desired program a 15 in the location where tone dialling should begin If the entire number should be tone dialling program a 15 inlocation 032 Example Phone number 02 7244211 with touch tone dialling would be entered as 15 4 10117 HIRI P ATP THT 2 E TTEA E 4 TE T E2 TE TIETET PANN O The 15 selects touch tone dialling and the 0 ends the phone number LOCATIONS 048 051 PROGRAMMING THE ACCOUNT CODE FOR THE PRIMA RY PHONE NUMBER The account code sent when the PRIMARY phone number is dialled is programmed in locations 048 051 Any zero 0 within the account code must be programmed as a 10 and the communicator will report a zero 0 If the account code is three digits long use locations 048 049 and 050 Program a 0 to indicate the end of the account code Example Account number of 2090 would be entered as 2 7 10 9 10 O 7 starting at location 48 Account code of 209 for low speed would be entered as 2 10 9 7 0 starting at location 48 LOCATION 052 PROGRAMMING COMMUNICATOR FORMAT FOR THE PRIMARY PHONE NUMBER Location 052 contains the communicator format used to transmit to the receiver connected to the primary phone number Consult the instructions for your central station receiver to determine which format is compatible To select Ademco High Speed program a 4 in location 052 Contact I D requires a 1 in this
2. The siren bell can be programmed to activate upon different conditions Using the chart below add the values of the desired condition s and program the sum of those values in location 142 When the siren bell is activated by pressing the 1 and 7 keys simultaneously the communicator will not report a message and the siren bell can be silenced by entering an arm disarm code Activation by pressing 1 and 7 keys simultaneously sss LOCATION 143 SMOKE POWER RESET AND OR FIRE ALARM VERIFICATION Programming a 1 in location 143 will cause the DL100 when in the disarmed state to interrupt the smoke detector power each time the button is pressed If this location contains a 0 the smoke detector power will reset only after the button is pressed when the corresponding LED s for zones designated as Priority are on steady for alarm or blinking for trouble Programming a 2 in this location will enable the Fire Alarm Verification feature When the Fire Alarm Verification feature is enabled a smoke detector will be powered down and reset automatically after the first trip waiting for a second trip within a 30 minute time frame thus verifying a fire alarm condition before creating an alarm and communicating a message LOCATION 144 RESERVED FOR FUTURE USE LOCATION 145 148 PROGRAMMING THE AUXILIARY OUTPUTS The DL100 has 4 auxiliary outputs located on terminals 1 thru 4 on the control PC board These outputs can
3. PROGRAMMING TO REPORT CLOSING The DAS DL100 has the ability to report a closing code each time the control is armed Program a 1 in this location to enable this report When using a one button Quick Arm code and when using the remote arming input the user number one 1 is reported The closing report will not be initiated until the end of the exit delay When Ademco high speed is selected a U444 4444 4 event is reported When Contact LD is selected an event 401 Open Close is reported If this location contains a 0 closing will not be reported LOCATION 103 PROGRAMMING TO REPORT OPENINGS The DAS DL100 has the ability to report an opening code each time the control is disarmed Program a 1 in this location to enable this report When using the remote arming input the user number one 1 is reported WhenAdemco high speed is selected a U222 2222 2 event is reported When Contact I D is selected an event 401 Open Close is reported If this location contains O openings will not be reported LOCATION 104 105 PROGRAMMING THE COMMUNICATOR CODE FOR ZONE 1 Locations 104 105 contain the communicator code to be reported each time zone 1 creates an alarm Location 104 contains the standard digit and location 105 contains the extended digit When using Ademco High Speed program a one 1 in the first location to enable this report a 1555 5555 7 is reported When contact I D is selected program the extended or the second locatio
4. b ENTRY EXIT A trip will start entry delay The lack of a trip during exit delay will enable the Automatic Bypass or Instant mode if so programmed 4 INTERIOR DELAY A trip on Interior Delay zone will initiate an entry delay It will be ignored during exit delay and when disarmed This zone type is used with the Automatic Bypass Instant mode 5 HANDOVER Interior zone that follows delay zones It can be bypassed before arming or automatically bypassed in the Automatic Bypass Instant mode if so programmed INSTANT Produces an instant alarm when tripped in the armed mode ignored when disarmed EAR 24 HOUR SILENT A trip on a 24 hour silent zone will communicate to the central station when the DAS DL100 is armed or disarmed PRIORITY A short on a Priority zone type will communicate to the central station when the DAS DL100 is armed or disarmed Priority zones cannot be bypassed M SECONDARY DELAY A secondary delay zone works like an interior delay zone but has its own independent delay time see locations 178 179 NOTE WHEN PROGRAMMING THE FOLLOWING COMMUNICATOR CODES A 10 MUST BE PROGRAMMED IN ORDER TO REPORT A ZERO 0 LOCATION 086 087 PROGRAMMING THE DAS DL100 FOR DURESS CODE CAPABILITY The DAS DL100 has the ability to report a duress code when the system is armed or disarmed with user code number 7 and a duress communicator code is programmed in locations 086 087 Location 086 contains the standard di
5. Entry Guard Programming a 1 in this location will cause the control to automatically enter the Instant mode and bypass interior follower zones if a fault is not detected on an entry exit zone during the exit delay Programming a 3 in this location Automatic Bypass will cause the interior follower zones to become bypassed if a fault is not detected on an entry exit zone yet will not change the status of the entry exit zone Programming a 8 will enable the Partial Arm security feature which requires a four digit code to disarm the Partial Arm mode If this location contains a O these features are disabled DATA CHARACTERISTIC ENABLE AUTO INSTANT MODE 3 ENABLE AUTO HANDOVER ISOLATE WITH ENTRY ZONE DELA Y ENABLE PARTIAL MODE ENTRY GUARD SECURITY FEATURE 15 LOCATION 132 BUILT IN SIREN DRIVER 1 AMP VOLTAGE OUTPUT The built in siren driver has a steady sound for Priority zone type and a yelp sound for Burglary and Panic Factory default is O enabling this feature If the built in siren driver is NOT to be used take the following procedure First remove the jumper on the PC board Next program a 1 in location 132 Finally replace the jumper in the voltage position Terminals 21 amp 22 will now output 1 Amp at 12VDC The Fire Panic and Burglary options for the Auxiliary Outputs can be programmed for momentary or to follow the siren Programming a 2 in location 132 will cause the Fire Panic or Burglary a
6. TYPE oemsmwr ZONE 4 ZONE TYPE ons 1 7 e ZONE 1 ZONE TYPE ZONE 2 ZONE TYPE ZONE 5 ZONE TYPE 6 INSTANT 6 INSTANT COMMUNICATOR CODES PAGE DESCRIPTION CODE EXTENDED CODE DEFAULT DunesscouuuNcaTOR CODES rise CODE PAD AUX 1 COMMUNICATOR CODE J eDISABEED _ CODE PAD AUX 2 COMMUNICATOR CODE J eDISABEED _ cope rap PANIC COMMUNICATORCODE onsem CODE PAD TAMPER COMMUNICATOR CODE _ wDISABEED 12 boWNLOADCOMPLETECOMMUNICMTORCODE onw l AUTOTESTCOMMUNICATORCODES osans ls RESERVED RESERVED O CLOSING COMMUNICATOR CODE va ur DISABLED OPENING COMMUNICATOR CODE a MAN NUMBER 0 DISABLED COMMUNICATOR CODES ZONE WI COMMUNICATOR CODE Ys ZONE 2 COMMUNICATOR CODE L El ZONE 3 COMMUNICATOR CODE s gt ZONE 6 ZONE TYPE Re RESERVED ZONE 5 COMMUNICATOR CODE KT xx ZONE 6 COMMUNICATOR CODE E cO COMMUNICATOR CODES LOCATION PAGE DESCRIPTION CODE EXTENDED CODE DEFAULT 3 zowescommunicarorcoD E Yoo 4 ACPOWER COMMUNICATOR CODE osans 14 LOW BATTERY COMMUNICATOR CODE ODISABLED 14 TROUBLE COMMUNICATORCODE ZONENuMBER DISABLED 14 ISOLATE COMMUNICATOR CODE zoweNUwBER visas 4 RESTORE COMMUNICATOR CODE
7. amp 3 OUTPUT 18 LOCATION 150 AC POWER LOSS DELAY FEATURE Location 150 contains the number of one minute delays one to seven minutes the communicator will wait before reporting an AC power failure A 1 programmed in this location will create a one minute delay and a 7 will create a seven minute delay If a 0 is programmed in this location AC power failures will be reported immediately if AC power loss reporting is enabled in locations 120 121 LOCATION 151 PROGRAMMING THE NUMBER OF RINGS TO ANSWER DOWNLOAD CALL Location 151 contains the number of rings the DL100 must detect before answering the telephone when initiating a download If a number from 1 to 15 is programmed in this location the control will answer after THAT number of rings has been detected If a 0 is programmed in this location the DL100 will not answer the download call SEE LOCATION 212 ANSWERING MACHINE DEFEAT LOCATION 152 PROGRAMMING THE NUMBER OF DAYS LEFT UNTIL AUTOTEST REPORT Location 152 contains the number of days left until the next autotest report If this location contains a O an autotest signal will be reported the first time the current time equals the autotest time programmed in locations 162 165 Locations 098 099 must be programmed to enable autotest reporting LOCATION 153 PROGRAMMING THE CLOCK CURRENT MONTH Location 153 contains the current month The month must be programmed using a number from 1 to 12 Th
8. armed Factory default is 0 Force Arming disabled LOCATIONS 198 201 AUTOMATIC ARMING TIME Locations 198 201 contain the time of an automatic arming if automatic arming is enabled in location 202 The time is entered as 24 hour military time beginning with location 198 LOCATION 202 AUTOMATIC ARMING Programming a 1 in location 202 will enable Automatic arming The time of the arming is programmed in location 198 201 If automatic arming is enabled the code pad sounder will activate for 50 seconds before automatically arming If the sounder is silenced by entering a valid arm disarm code during the 50 Second time frame the panel will not automatically arm If the sounder is still on at the end of the 50 seconds the control will arm Any zones not secure will be bypassed when automatic arming is used If open close reports are enabled the DL100 will report user code 9 closing when it auto arms LOCATION 203 DYNAMIC BATTERY TEST The number programmed in location 203 determines the number of minutes the DL100 will perform dynamic battery testing during each 24 hour period The Battery test is preformed at 6 00 AM Programming a 0 in this location will disable this feature LOCATIONS 204 206 RESERVED FOR FUTURE USE LOCATIONS 207 CALLBACK PHONE NUMBER CONTROL The number programmed in location 207 controls the use of the callback telephone number programmed in locations 264 279 The callback number must be programmed in the do
9. enable this report a 5555 5555 9 is reported When contact I D is selected program a one 1 in the extended or the second location to enable this report an event 602 Autotest will be reported If locations 252 253 are O this report is disabled LOCATION 254 255 RESERVED FOR FUTURE USE 23 THE REMAINING LOCATIONS ARE ACCESSIBLE ONLY THROUGH DOWNLOADING LOCATIONS 256 263 CONTROL PANEL ACCESS CODE Locations 256 263 contain the eight digit access code the DL100 must receive from the downloading software before the panel will permit downloading to occur The factory default code is listed in the instructions provided with the DASLOAD downloading software package LOCATIONS 264 279 CALL BACK TELEPHONE NUMBER The presence of a phone number in locations 264 279 will cause the control panel to dial back this number after a successful panel access code has been entered If a telephone number is present the control panel will hang up for approximately 36 seconds insuring that the calling party has disconnected then it will call back Any zero 0 within the telephone number must be programmed as an A If tone dialling is desired program an F in the location where tone dialling should begin If the entire number should be tone dialling program an F in location 194 Four second delays can be obtained anywhere in the sequence by programming a D in the appropriate delay location WARNING THE CALLBACK PHONE NUMBER SHOULD ALWAY
10. location If you need another format choose from those listed in the format table located on the following page and program the data in location 052 If this location contains a O the built in communicator will be disabled and the DAS DL100 will function as a local only control LOCATION 053 RESERVED FOR FUTURE USE LOCATIONS 054 069 PROGRAMMING THE SECONDARY TELEPHONE NUMBER Locations 054 069 contain the secondary telephone number This number allows certain communicator reports to go to another number or to cause the communicator to dial a second number if the primary number does not respond after the number of attempts programmed into location 134 have been tried unsuccessfully The same number of attempts are made with the back up number Tone dialling and delay instructions are the same as for the primary number LOCATIONS 070 074 RESERVED FOR FUTURE USE COMMUNICATOR FORMAT TABLE DESCRIPTION LOCAL ONLY C 1 ADEMCO CONTACT ID ADEMCO 4 2 EXPRESS PAGER FORMAT PORTS IN 4 3 FORMAT OR DOMESTIC DIALLING ADEMCO HIGH SPEED DTMF FORMAT RADIONICS EXTENDED SLOW 1800Hz TRANSMITTAL 2300Hz HANDSHAKE 20 PPS HEX EXT DOUBLE ROUND CADDX MODEM PROPRIETARY 7 RADIONICS EXTENDED FAST 1800Hz TRANSMITTAL 2300Hz HANDSHAKE 40 PPS HEX EXT DOUBLE ROUND RADIONICS EXTENDED FAST 1800Hz TRANSMITTAL 1400Hz HANDSHAKE 40 PPS HEX EXT DOUBLE ROUND RADIONICS EXT FAST 1800Hz TRANSMITTAL 2300Hz HANDSHAKE 40 PPS HEX W PARITY EXTENDED NOT USED AAA e
11. location 180 Answering Machine Defeat The DL 100 has the ability to defeat an answering machine to receive a call for up downloading see location196 Competitor Lockout Through downloading local programming can be locked out on the DL 100 This eliminates the ability to change programming data at the local level see location 281 z x529 n ES 1 Ey 9 E 8 E s dp ia SEL jw lk jie Ch Wa Lh sia 254 n Ca Si Fo a 277 fr B 85 id o SL da LJ POCO HH z TI s pel Fl pego E N RM R Aa TS T EA 5000 TO TAW pa sa 672333 abies ex lt lt lt 2 8592 TEE a DO wg L di N fo i toos iid TQ s wissssss E saait i 2 c OOOOOO z L I Ly lit lit Lu Ld z 6 Q 0 UU 0 4 TERMINAL DRAWING amp SPECIAL NOTES EMEN id STIS M F lia nt Es Aia iiid Rt Um SIE Ti Al E INI t 218 M Hf Vos RUD s oTA Sal 8 nan SHE ye ni 3 8 Ses REA NE QUIER 1 m 1 53 mis 75 1 INITE md g a a S N NO 1 17 18 19 20 210 22 230 244 25 amp 266 Battery leads TERMINAL DESCRIPTION DESCRIPTION Programmable Auxiliary Output Terminal Current limited to 250 micro amps positive and 200 mA negative This Auxiliary output is normally used to connect the negative lead of the strobe The positive lead of the strobe can be connected to any of the positive terminals Programmable Auxilia
12. locations 114 115 are O this report is disabled LOCATION 116 119 RESERVED FOR FUTURE USE LOCATION 120 121 PROGRAMMING TO REPORT AC POWER LOSS The DAS DL100 has the ability to report an AC power failure code when AC power is lost This report can be immediate or delayed depending on the information programmed in location 150 AC POWER LOSS DELAY The desired AC failure mode should be programmed in locations 120 121 Location 120 contains the standard digit and location 121 contains the extended digit When using Ademco High Speed program a one 1 in the first location to enable this report a 1555 5555 6 is reported When contact LD is selected program a one 1 in the extended or the second location to enable this report an event 301 A C Loss will be reported A C Loss will only report when the A C power has been disconnected for period equal to the minutes programmed in location 150 If both locations are 0 AC power failures will not be reported LOCATION 122 123 PROGRAMMING TO REPORT LOW BATTERY The DAS DL100 has the ability to report a low battery code when AC power has been lost and the battery has discharged down to 10 3 volts The desired low battery code is programmed in locations 122 123 Location 122 contains the standard digit and location 123 contains the extended digit When using Ademco High Speed program a one 1 in the first location to enable this report a 5155 5555 6 is reported When contact I D is select
13. program a one 3 in the first location to enable this report a 5515 5555 7 is reported When contact I D is selected program the extended or the second location with the required event code from appendix 1 to enable this report event programming a three 3 in the extended or the second location will select an event 130 Burglary to be reported The data in the standard location or first location must be left at default or changed to the zone number that is to be reported If locations 108 109 are O this report is disabled LOCATION 110 111 PROGRAMMING THE COMMUNICATOR CODE FOR ZONE 4 Locations 110 111 contain the communicator code to be reported each time zone 4 creates an alarm Location 110 contains the standard digit and location 111 contains the extended digit When using Ademco High Speed program a one 4 in the first location to enable this report a 5551 5555 7 is reported When contact I D is selected program the extended or the second location with the required event code from appendix 1 to enable this report event programming a three 3 in the extended or the second location will select an event 130 Burglary to be reported The data in the standard location or first location must be left at default or changed to the zone number that is to be reported If locations 110 111 are O this report is disabled 13 LOCATION 112 113 PROGRAMMING THE COMMUNICATOR CODE FOR ZONE 5 Locations 112 113 contain the communicator c
14. y ZONE NUMBER 0 DISABLED 5 CANCEL COMMUNICATOR CODE hc MAN NUMBER 0 DISABLED 26 PROGRAMMING OPTIONS DEFAULT ws s ABORTENAME isa ww is PSIUENTCODPADPANC O v AUDIBEE u s SIREN amp COMMUNICATOROUTPUTLIMTTATION m 0 DISABLED 6 NUMBEROFDIALATTEMPIS 135 POWER UP CONDITION 0 LAST CON POWER UP DELAY S DISABLED 0 SIREN 0 DISABLED 6 ATTEMPTS IMMEDIATE RESTORE 1 ENABLED im 7 BELL TEST CONTROL 0 DISABLED 142 17 emresreowreor SMOKE POWER RESET AND OR FIRE ALARM VERIFICATION 0 DISABLED AUXILIARY OUTPUT OPTIONS LOCATION PAGE DESCRIPTION DATA DEFAULT 145 AUX PIN 1 PO 11 STROBE AUX PIN 2 0 BURG ALARM AUX PIN 3 s ARMED LED 0 DISABLED 0 DISABLED RESERVED AUX PIN 4 149 AUXILIARY OUTPUT INVERSION 14 READY LED 0 DISABLED PROGRAMMING TIMER OPTIONS LOCATION PAGE DESCRIPTION DATA DEFAULT 150 as AC POWER FAIL REPORT DELAY OPT 0 THRU 7 1 MIN INC 0 DISABLED NUMBER OF RINGS TO ANSWER DOWNLOAD CALL NUMBER OF DAYS LEFT UNTIL AUTOTEST REPORT MONTH OF THE YEAR JANUARY 1 DECEMBER 12 154 CURRENT YEAR TENS DIGIT 1994 9 ESA ET EA NN 155 w OURRENT YEAR ONES DIGIT aossen Oooo o 16 w DAY OF THE MONTH TENS DIGIT aSTH DAY OF THE MONTH ONES DIGIT 25TH 5 u is w QURRENTHOUR TENSDIG o i9 o cumeTHoUR ONESDUIT O U
15. 8 DEFAULT 6 60 SECONDS 6 60 SECONDS 0 DISABLED 0 DISABLED 0 DISABLED RESERVED 6 6 6 6 6 6 RESERVED 0 DISABLED 0 DISABLED 2 2 0 0 0 DISABLED 0 DISABLED RESERVED 0 DISABLED 0 DISABLED RESERVED g g g g g g RESERVED 0 DISABLED 0 DISABLED RESERVED DEFAULT 10000000 O DISABLED APPENDIX 1 This document lists the event reporting codes for Ademco Contact ID reporting in the DL 100 The event codes are programmed by placing a number from 0 15 in the extended or second location of the communicator code for the event being reported The following event codes will be sent for the digit programmed PROGRAMMED 100 s DIGIT N 00 10 QA AUD veo c Q Q ADEMCO EVENT CODE 122 110 120 130 131 132 133 134 135 150 121 100 123 137 602 300 DEFINITION SILENT PANIC FIRE PANIC BURGLARY PERIMETER BURGLARY INTERIOR BURGLARY 24 HOUR AUXILIARY ENTRY EXIT BURGLARY DAY NIGHT BURGLARY NON BURG 24 HOUR DURESS MEDICAL ALARM AUDIBLE PANIC TAMPER AUTO TEST SYSTEM TROUBLE The following event codes are sent automatically but must be enabled by programming a 1 in the communicator code location for that report REPORTING EVENT KEYPAD TAMPER AUTOTEST FAIL TO COMMUNICATE OPENING CLOSING CANCEL A C LOSS RESTORE ZONE ISOLATE ZONE TROUBLE LOW BATTERY BATTERY T
16. ATION 096 097 PROGRAMMING TO REPORT DOWNLOADING COMPLETE Locations 096 097 contain the communicator report sent each time a download session has been completed The report will come in after a disconnection has been made from a downloading session Location 096 contains the standard communicator code and location 097 contains the extended communicator code When using Ademco High Speed program a one 1 in the first location to enable this report a 5515 5555 6 is reported When contact I D is selected program a one 1 in the extended or the second location to enable this report an event 412 Download Complete will be reported If locations 096 097 are O this report is disabled LOCATION 098 099 PROGRAMMING FOR AUTOTEST REPORTS The DAS DL100 has the ability to send autotest reports at intervals from 1 to 15 days Locations 098 099 contain the communicator codes sent for autotest Location 098 contains the standard communicator code and location 099 contains the extended communicator code When using Ademco High Speed program a one 1 in the first location to enable this report a 5555 5555 9 is reported When contact I D is selected program a one 1 in the extended or the second location to enable this report an event 602 Autotest will be reported If locations 098 099 are 0 autotest is disabled NOTE WHEN USING AUTOTEST LOCATIONS 152 166 MUST BE PROGRAMMED 12 LOCATION 100 101 RESERVED FOR FUTURE USE LOCATION 102
17. ATION PAGE DESCRIPTION ACCOUNT CODE DEFAULT 048 051 ea PRIMARY ACCOUNT NUMBER ERE 0 DISABLED XIMARY FORMAT LOCATION PAGE DESCRIPTION FORMAT DEFAULT 052 NN PRIMARY FORMAT OPT 1 THRU 15 0 DISABLED ZCONDARY PHONE NUMBER LOCATION PAGE DESCRIPTION PHONE NUMBER DEFAULT 054 061 SECONDARY PHONE NUMBER DIGITS 1 8 Il 0 DISABLED 062 069 1 SECONDARY PHONE NUMBER DIGITS 9 16 J b po pon 0 DISABLED FORMAT SELECT TABLE DATA FORMAT DESCRIPTION 6 capDxmoDEs PROPRIETARY j RADIONICS EXTENDED FAST 1800Hz TRANSMITTAL 1400Hz HANDSHAKE 40 PPS HEX EXT DOUBLE ROUND RADIONICS EXT FAST W PARITY 1800Hz TRANSMITTAL 2300Hz HANDSHAKE 40 PPS HEX EXTENDED CUSTOM FORMAT SELECT YOU OWN FORMAT FOR NON STANDARD BASE STATIONS 25 LOCATION LOCATION 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 LOCATION 104 105 106 107 108 109 110 111 112 113 114 115 116 119 120 121 122 123 124 125 126 127 PROGRAMMING OPTIONS DESCRIPTION DATA DEFAULT PRIMARY ENTRY DELAY OPT 0 THRU 15 10 SEC INC 2 20 SECONDS PRIMARY EXIT DELAY OPT 0 THRU 15 10 SEC INC u 6 60 SECONDS SIREN CUTOFF TIME OPT O THRU 15 2 MIN INC 4 8 MINUTES PAGE ZONE TYPES FOR ZONES 1 6 PAGE DESCRIPTION DATA DEFAULT ren wHawpoveg O ZONE 3 ZONE
18. DL100 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL TABLE OF CONTENTS GENERAL DESCRIPTION l dieu paye dos kasab oo sons eee ae bous sede e sd edo dee EO L P 2 STANDARD AND OPTIONAL PARTS LIST P 2 BEATURE DEFINITIONS iieri tenet redet ido ee uu terr te det pee de P 3 TERMINAL DRAWING AND SPECIAL NOTES eee P 4 TERMINAL DESCRIPTION 5 a aw se va rain ber Eee aa SRA P 5 HOW TO PROGRAM THE DAS DLIOO P 6 CODE PAD PROGRAMMING EXAMPLES sese P 7 OPTIONAL 8950 PROGRAMMER EXAMPLE emm P 7 9 REQUIRED PROGRAMMING INSTRUCTIONS P 8 10 COMMUNICATOR FORMAT SELECTION GUIDPE P 9 11 OPTIONAL PROGRAMMING INSTRUCTIONS P 10 23 12 DOWNLOAD PROGRAMMING INSTRUCTIONS P 24 13 PROGRAMMING WORKSHEETS sse Heer P 25 28 APPENDIX iore ve A n ke e ka ae ds be e a seen e de P 29 15 SPECIFICATIONS amp WARRANTY P 32 DAS DL100 INSTALLATION MANUAL General Description The Das DL100 is a versatile 6 zone up downloadable security control with a built in digital communicator Its microcomputer design gives some of the most versatile yet easy to use features available for most security applications today Each of the six zones can be programmed
19. E ENABLE FAST LOOP RESPONSE see location FAST LOOP RESPONSE 180 CHIME ENABLE ZONE ISOLATE CAPABILITY GROUP ISOLATE ZONE CHIME ENABLE FAST LOOP RESPONSE FAST LOOP RESPONSE ZONE ISOLATE CAPABILITY ZONE ISOLATE CAPABILITY CHIME ENABLE CHIME ENABLE ZONE ISOLATE CAPABILITY GROUP ISOLATE ZONE ZONE RESTORAL REPORTING ZONE RESTORAL REPORTING CHIME ENABLE FAST LOOP RESPONSE 13 FAST LOOP RESPONSE ZONE RESTORAL REPORTING ZONE RESTORAL REPORTING FAST LOOP RESPONSE FAST LOOP RESPONSE ZONE ISOLATE CAPABILITY ZONE ISOLATE CAPABILITY ZONE RESTORAL REPORTING ZONE RESTORAL REPORTING CHIME ENABLE 21 LOCATIONS 192 195 RESERVED LOCATIONS LOCATION 196 ANSWERING MACHINE DEFEAT Location 196 contains the answering machine defeat To defeat an answering machine two telephone calls must be made to the premises On the first call let the phone ring the same number of times or less as the number programmed in this location maximum 3 The control panel will detect these rings and start a 45 Second timer If a call comes in during that 45 Second time frame the control panel will answer on the first ring To disable this feature program a 0 in this location LOCATION 197 AUTO ISOLATE Programming a 1 in location 197 will allow the DAS DL100 to be armed without all the zones secure no Ready LED illuminated Any zones that are not secure at the end of the exit delay will be automatically bypassed while zones that are secure will be
20. ER 7 Locations 024 027 contain the arm disarm code for Duress or for user number 7 Duress capability is enabled by programming a communicator code in locations 086 087 If locations 086 087 are left unprogrammed user number 7 will act as a standard user code LOCATIONS 028 031 PROGRAMMING THE GO TO PROGRAM ACCESS CODE Locations 028 031 contain the Go To Program access code Location 028 contains the first digit of the code and location 031 contains the fourth digit of the code THE CODE MUST CONTAIN FOUR 4 DIGITS With the DAS DL100 disarmed the Go To Program access code can be used to enter the program mode To disable the Go To Program access code program a 15 in location 028 The factory default setting is 9 7 1 3 LOCATIONS 032 074 SEE PAGE 8 LOCATION 075 PROGRAMMING THE ENTRY DELAY TIME Location 075 contains the number of 10 Second increments in the entry delay The entry delay can be programmed in 10 second increments from 10 to 150 seconds 1 10 seconds through 15 150 seconds For example programming a 2 in this location will produce an entry delay of 20 seconds Note A 0 entry is treated as 0 seconds Programming a 6 in this location will produce an entry delay of 60 seconds Factory default is 30 seconds LOCATION 076 PROGRAMMING THE EXIT DELA Y TIME Location 076 contains the number of 10 Second increments in the exit delay The exit delay can be programmed in 10 second increments from 10 t
21. EST FAIL DOWNLOAD COMPLETE ADEMCO EVENT DIGIT 137 602 354 401 406 301 EVENT CODE FOR ALARM 570 380 302 309 412 29 124 LOCATIONS 095 099 101 103 102 127 121 126 125 123 123 097 APPENDIX 2 This document describes the DL 100 reporting event codes when using the SIA format format 14 The following codes are programmable and are sent when the 100 s digit is programmed as the event code The 10 s and 1 s digit are then sent as a zone identifier PROGRAMMED 100 s DIGIT SIA CODE DEFINITION 0 PA PANIC ALARM 1 FA FIREALARM 2 PA PANIC ALARM 3 BA BURGLARY ALARM 4 GA GAS ALARM 5 KA HEAT ALARM 6 WA WATER ALARM 7 QA EMERGENCY ALARM 8 SA SPRINKLER ALARM 9 UA UNTYPED ALARM 10 HA HOLDUP ALARM 11 MA MEDICAL ALA RM 12 ZA FREEZE ALARM 13 TA TAMPER ALARM 14 RP PERIODIC TEST 15 RESERVED The following event codes are fixed but must be enabled by programming a 1 in the corresponding location REPORTING EVENT SIA CODE PROGRAMMING LOCATION TAMPER TA 095 AUTOTEST RP 099 FAIL TO COMMUNICATE RT 101 OPENING OP 103 CLOSING CL 102 CANCEL OC 127 AC LOSS AT 121 LOW BATTERY YT 123 RESTORE CODE R 126 ISOLATE CODE B 125 ISOLATE RESTORE U 126 125 TROUBLE CODE T 124 TROUBLE RESTORE R 124 126 AC RESTORE AR 126 BATTERY RESTORE YR 126 DOWNLOAD COMPLETE RS 097 The character transmitted in this location will be the first character in the SIA code from the top list for the event being transmitted If a 1 is program
22. NDEHNED S p S S 7 TENE 0 DISABLED UNDEFINED UNDEFINED UNDEFINED UNDEFINED UNDEFINED UNDEFINED CURRENT MINUTE TENS DIGIT UNDEFINED CURRENT MINUTE ONES DIGIT AUTOTEST TIME HOUR TENS DIGIT 164 6 2 167 177 RESERVED UNDEFINED UNDEFINED UNDEFINED UNDEFINED UNDEFINED UNDEFINED RESERVED 21 LOCATION 178 179 0 182 183 184 185 e 6 7 8 189 190 191 192 195 196 197 198 9 0 2 2 e 2 E 2 203 204 206 207 208 209 N N N N N N N N N N N N N 210 243 244 2 Un 246 2 7 248 249 250 251 2 2 253 254 255 LOCATION 256 263 PAGE 22 22 b JN N t2 N t2 t N JNM t2 22 22 23 23 23 23 23 23 23 23 23 3 3 2 2 2 3 23 PROGRAMMING OPTIONS DESCRIPTION SECONDARY ENTRY DELAY OPT 0 THRU 15 10 SEC INC ONDARY EXIT DELAY LOOP RESPONSE TIME RESERVED OPT 0 THRU 15 10 SEC INC OPT O THRU 15 20 m SEC INC DATA THE FOLLOWING LOCATIONS ARE ACCESSIBLE ONLY THROUGH DOWNLOADING 24 24 DESCRIPTION CONTROL PANEL ACCESS CODE 264 271 CALLBACK PHONE NUMBER DIGITS 1 8 l 0 DISABLED 272 279 CALLBACK PHONE NUMBER DIGITS 9 16 Wide TP ME IN II 0 DISABLED m LOCAL PROGRAMMING LOCKOUT ERE 0 DISABLED CONTROL PANEL SHUTDOWN EN 2
23. S BE REVIEWED FOR ACCURACY BEFORE DISCONNECTING LOCATION 280 MUST BE SET TO 0 LOCATION 281 LOCAL PROGRAMMING LOCKOUT Location 281 is used to disable local programming lockout If a 5 is programmed in this location all local programming is locked out If an A is programmed in this location all programming functions related to the digital communicator will be locked out Any other number in location 281 will allow all local programming LOCATION 282 CONTROL PANEL SHUTDOWN Location 282 is used to shut down the control panel Programming an A in this location will completely shutdown the control panel The code pad will appear dead and the siren and communicator will not operate WARNING EXTREME CARE SHOULD BE TAKEN NOT TO INADVERTENTLY PROGRAM THIS LOCATION 24 RM DISARM CODES 1 15 LOCATION PAGE DESCRIPTION DATA 1 DATA 2 DATA 3 DATA 4 DEFAULT 000 003 USER 1 ARM DISARM CODE en 004 007 USER 2 ARM DISARM CODE i Rx 5 DISABLED 008 011 SER 43 ARM DISARM CODE 1 A 5 DISABLED 012 015 USER 4 ARM DISARM CODE S U 5 DISABLED 016 019 USER 5 ARM DISARM CODE 8 5 DISABLED 020 023 5 DISABLED 024 027 USER 7 ARM DISARM CODE aa 5 DISABLED 31MARY PHONE NUMBER LOCATION PAGE DESCRIPTION PHONE NUMBER DEFAULT 032 039 s PRIMARY PHONE NUMBER DIGITS 1 8 0 DISABLED 040 047 Ea PRIMARY PHONE NUMBER DIGITS 9 16 EL II LE 0 DISABLED Q31MARY ACCOUNT NUMBER LOC
24. S DIGIT Location 165 contains the ones digit of the minutes after the hour that the autotest is desired The time is entered in 24 hour time If the desired autotest time is 5 25 PM the 24 hour time is 17 25 so this location should contain a 5 which is the ones digit of the minutes for autotest time If the desired autotest time is 9 36 AM the 24 hour time is 09 36 and this location should contain a 6 LOCATION 166 PROGRAMMING THE AUTOTEST TIME REPORTING INTERVALS Location 166 contains the number of days between automatic test reports If a report is desired every 7 days this location should contain a 7 Valid entries are 1 to 15 days LOCATION 167 178 RESERVED FOR FUTURE USE LOCATION 178 PROGRAMMING THE SECONDARY ENTRY DELAY ZONE TYPE 9 Location 178 contains the number of 10 second increments in the exit delay The exit delay can be programmed in 10 second increments from 10 to 150 seconds 1 10 seconds through 15 2150 seconds For example programming a 2 in this location will produce an exit delay of 20 seconds Note A 0 entry is treated as O seconds Programming a 6 in this location will produce an exit delay of 60 seconds Factory default is 60 seconds 20 LOCATION 179 PROGRAMMING THE SECONDARY EXIT DELAY ZONE TYPE 9 Location 179 contains the number of 10 Second increments after arming before trips will be recognised on a zone type 9 The exit delay can be programmed in 10 second increments fr
25. allation manual and you may begin programming the control panel When using an optional plug in programmer which automatically enters the programming mode the only entry necessary is 9 5 0 to load factory defaults PROGRAMMING EXAMPLE FIGURE 2 ZONE 4 LED 8 J PATA 9 ZONE 3 LED 4 No LED s Illuminated 0 ZONE 1 LED 1 ZONE 2 LED 2 DATA 28 To change or enter data in loca Pressing the Key will advance tlon shown enter data and fol to next location or specific ioca low by the Key tions can be reached by press ing location number followed by the Key FS4597 PROGRAMMER FIGURE 3 Location Indicator 1 Thru 0 Data Keys Location Advance Key Data indicator Data Enter Change key 7 PROGRAMMING THE COMMUNICATOR THIS PAGE DESCRIBES ALL THE LOCATIONS THAT MUST BE PROGRAMMED IN ORDER FOR THE DAS DL100 TO FUNCTION AND REPORT TO A CENTRAL STATION OTHER OPTIONS MAY BE SELECTED BY FOLLOWING THE ADDITIONAL PROGRAMMING INSTRUCTIONS LOCATIONS 032 047 PROGRAMMING THE PRIMARY TELEPHONE NUMBER The primary telephone number is programmed in successive locations beginning with location 032 Any zero 0 within the telephone number must be programmed as a 10 A 0 indicates the end of the phone number Delays of four seconds can be programmed at any point in the phone number by programming a 13 in the appropriate location If a or are required in your phone number then a 11 and 12
26. be activated by 10 different conditions To utilise the outputs program a number from 0 to 9 in locations 145 output 1 to location 148 output 4 according to the desired characteristics listed on the following page Output 1 is terminal 1 and output 4 is terminal 4 17 AUXILIARY OUTPUT TABLE 0 BURGLARY ALARM LATCHED OUTPUT LATCHED OUTPUT x o DAMPERALARM LATCHEDOUTPUT AUTOTEST MOMENTARYOUTPUT STATUS LED LATCHED OUTPUT LOCATIONS 149 INVERTING THE AUXILIARY OUTPUTS The auxiliary outputs of the DL100 are normally POSITIVE going NEGATIVE They can be changed to a normally NEGATIVE going POSITIVE by programming the appropriate number in location149 Auxiliary output 1 has a value of 1 Auxiliary output 2 has a value of 2 Auxiliary output 3 has a value of 4 and Auxiliary output 4 has a value of 8 The values for the outputs that you wish to change to NEGATIVE going POSITIVE must be added together and the total programmed in location 149 For example if you wished to make outputs 2 2 and 3 4 NEGATIVE going POSITIVE you would program 6 2 4 6 in location 149 NOTE CURRENT LIMITED TO 250 MICRO AMPS POSITIVE AND 20 mA NEGATIVE VALUE OUTPUT INVERSION VALUE OUTPUT INVERSION NO AUX INVERTED INVERT AUX 1 OUTPUT INVERT AUX 2 OUTPUT INVERT AUX 1 amp 2OUTPUT INVERT AUX 3 OUTPUT INVERT AUX 1 amp 3 OUTPUT INVERT AUX 2 amp 3 OUTPUT INVERT AUX 1 2
27. d into the Program mode by use of the new FS4610 Smart Programmer or the original FS4597 programmer or for Code Pad programming by utilising the FS4534 LCD Code Pad the preferred method or the FS4623 LED Code Pad These methods are described below Using a Programmer The FS4610 Smart Programmer has been designed to make programming of the DL100 simpler as well as more efficient for users The FS4610 programmer features up to 4 resident standard programs to allow for separate system standardisation Plug the optional model FS4610 programmer into the 4 pin male outlet marked program on the DL100 P C Board Using The LCD Code Pad The most straightforward method of Code Pad programming is to utilise the FS4534 LCD Code Pad in the programming mode To access the programming mode enter C 0 0 followed by the four digit Go To Program access code which is factory default 9 0 5 0 this code can be reprogrammed and follow the Code Pad prompts Using The LED Code Pad The DL100 can also be programmed by the standard binary method of Code Pad programming described below When the FS4623 LED Code Pad is used for programming enter the factory default four digit Go To Program access code of 9 7 1 3 NOTE The DL100 must be disarmed to gain access to programming with this code After entry of this code the DL100 will be in the Program mode and the yellow LED s will display the data in location 000 The data is displayed usi
28. e 11 ADEMCOSSILENT KNIGHT 1900Hz TRANSMITTAL 1400Hz HANDSHAKE 10 PPS DOUBLE SLOW ROUND PARITY 12 SILENT KNIGHT 4 2 FAST 1900Hz TRANSMITTAL 1400Hz HANDSHAKE 20 PPS DOUBLE ROUND PARITY 13 SESCOA FRANKLIN FAST 1800Hz TRANSMITTAL 2300Hz HANDSHAKE 20 PPS HEX DOUBLE ROUND FSK FORMAT IA 15 CUSTOM FORMAT SELECT YOU OWN FORMAT FOR NON STANDARD BASE STATIONS REF TO YOUR DAS BRANCH FOR MORE INFORMATION OMMUNICATOR IS DISABLED TMF FORMAT T T D DTMF FORMAT RE E EE LOCATIONS 000 003 PROGRAMMING THE MASTER ARM DISARM CODE Locations 000 003 contain master arm disarm code user number 1 Location 00 contains the first digit of the code location 003 contains the fourth digit of the code THE CODE MUST CONTAIN FOUR 4 DIGITS The master code can then be used in the run mode to enter arm disarm codes 1 7 see page 40 ENTERING AND CHANGING THE MASTER CODE The factory default code is 1 2 3 4 LOCATIONS 004 023 PROGRAMMING THE ARM DISARM CODE FOR USERS 2 THRU 6 Locations 004 023 contain the arm disarm codes for user numbers 2 thru 6 Location 004 contains the first digit of the code 2 and location 007 contains the fourth digit of code 2 THESE CODES MUST CONTAIN FOUR 4 DIGITS To disable a code PROGRAM a 15 as the first digit of the code These codes can be changed in the RUN mode using the master code see page 38 ENTERING AND CHANGING AUXILIARY CODES LOCATIONS 024 027 PROGRAMMING THE DURESS CODE OR US
29. ed program a one 1 in the extended or the second location to enable this report an event 302 Low Battery will be reported Low battery will only report when the A C power is disconnected and the battery voltage drops below 10 2v D C If both locations are 0 low battery will not be reported LOCATION 124 PROGRAMMING FOR PRIORITY ZONE TROUBLE REPORTING The DAS DL100 has the ability to report a trouble code each time a Priority zone opens The desired trouble code is programmed in location 124 When using Ademco High Speed program a one 1 in this location to enable this report A one 1 will be displayed for the channel corresponding to the zone in Trouble alarm E G 5155 5555 5 will be reported for zone two 2 When contact I D is selected program a one 1 in this location to enable this report an event 380 Zone Trouble will be reported If this location contains a O the Priority Trouble will not be reported LOCATION 125 PROGRAMMING FOR ISOLATE REPORTING The DAS DL100 has the ability to report an Isolate on zones 1 6 The desired Isolate code is programmed in location 125 When using Ademco High Speed program a one 1 in this location to enable this report A one 1 will be displayed for the channel corresponding to the zone that is Isolated E G 5155 5555 3 will be reported for zone two 2 When contact I D is selected program a one 1 in this location to enable this report an event 380 Zone Isolate will be re
30. git and location 087 contains the extended digit When using Ademco High Speed program a one 1 in the first location to enable this report a 1555 5555 1 Duress is reported When contact I D is selected program the extended or the second location with the required event code from appendix 1 to enable this report event Programming a 10 in location 87 will report an event 121 Duress The Open Close report will accompany the Duress report complete with the user number to indicate that an Open or Close was preformed under Duress No restore code is reported for this event If both locations are O the duress capability is disabled and user code number 7 can only be used as a standard arm disarm code 11 LOCATION 088 089 PROGRAMMING FOR AUXILIARY 1 1 amp 3 DOUBLE KEYPRESS The DAS DL100 has the ability to report an Auxiliary 1 code and activate the Priority siren each time the 1 and 3 keys are pressed simultaneously on the code pad The desired reporting code is programmed in locations 088 089 Location 088 contains the standard digit and location 089 contains the extended digit When using Ademco High Speed program a one 1 in the first location to enable this report a 1555 5555 1 Duress is reported When contact I D is selected program the extended or the second location with the required event code from appendix 1 to enable this report event Programming a 1 in location 89 will report an event 110 Fire If activated t
31. he current hour tens digit The time is entered in 24 hour time If the current time is 5 25 PM the 24 hour time is 17 25 so this location should contain a 1 which is the current hour tens digit If the current time is 9 36 AM the 24 hour time is 09 36 so this location should contain a O 19 LOCATION 159 PROGRAMMING THE CLOCK CURRENT HOUR ONES DIGIT Location 159 contains the current hour ones digit The time is entered in24 hour time If the current time is 5 25 PM the 24 hour time is 17 25 so this location should contain a 7 which is the current hour ones digit If the current time is 9 36 AM the 24 hour time is 09 36 and this location should contain a 9 LOCATION 160 PROGRAMMING THE CLOCK CURRENT MINUTES TENS DIGIT Location 160 contains the current minutes tens digit The time is entered in 24 hour time If the current time is 5 25 PM the 24 hour time is 17 25 so location 160 should contain a 2 which is the current minutes tens digit If the current time is 9 36 AM the 24 hour time is 09 36 and this location should contain a 3 LOCATION 161 PROGRAMMING THE CLOCK CURRENT MINUTES ONES DIGIT Location 161 contains the current minutes ones digit The time is entered in 24 hour time If the current time is 5 25 PM the 24 hour time is 17 25 so this location should contain a 5 which is the current minutes ones digit If the current time is 9 36 AM the 24 hour time is 09 36 and this locatio
32. he siren can be silenced by entering any arm disarm code No restore code is reported for this event If both locations are 0 the Auxiliary 1 double keypress is disabled LOCATION 090 091 PROGRAMMING FOR AUXILIARY 2 4 amp 6 DOUBLE KEYPRESS The DAS DL100 has the ability to report an Auxiliary 2 code and activate the pulsing buzzer each time the 4 and 6 keys are pressed simultaneously on the code pad The desired Auxiliary 2 code is programmed in locations 090 091 Location 090 contains the standard digit and location 091 contains the extended digit When using Ademco High Speed program a one 1 in the first location to enable this report a 1555 5555 1 Duress is reported When contact I D is selected program the extended or the second location with the required event code from appendix 1 to enable this report event Programming a 11 in location 91 will report an event 100 Medical If activated the code pad sounder can be silenced by entering any Arm Disarm code No restore code is reported for this event If both locations are 0 the Auxiliary 2 double keypress is disabled LOCATION 092 093 PROGRAMMING FOR Code pad PANIC amp DOUBLE KEYPRESS The DAS DL100 has the ability to report a Code pad panic code and activate the Burg siren each time the and keys are pressed simultaneously on the code pad The desired Code pad panic code is programmed in locations 092 093 Location 092 contains the standard digit and
33. is location must be programmed when using the maintenance code feature see location 167 LOCATION 154 PROGRAMMING THE CLOCK CURRENT YEAR TENS DIGIT Location 154 contains the current year tens digit If the current year is 1994 this location should contain a 9 which is the tens digit of the current year LOCATION 155 PROGRAMMING THE CLOCK CURRENT YEAR ONES DIGIT Location 155 contains the current year ones digit If the current year is 1994 this location should contain a 4 which is the ones digit of the current year If the current year is 1995 this location should contain a 5 which is the ones digit of the current year LOCATION 156 PROGRAMMING THE CLOCK CURRENT DAY OF THE MONTH TENS DIGIT Location 156 contains the current day of the month tens digit If the current day of the month is the 5th 05 this location should contain a O which is the current day of the month tens digit If the current day of the month is the 26th this location should contain a 2 LOCATION 157 PROGRAMMING THE CLOCK CURRENT DAY OF THE MONTH ONES DIGIT Location 157 contains the current day of the month ones digit If the current day of the month is the 5th 05 this location should contain a 5 which is the current day of the month ones digit If the current day of the month is the 26th this location should contain a 6 LOCATION 158 PROGRAMMING THE CLOCK CURRENT HOUR TENS DIGIT Location 158 contains t
34. location 093 contains the extended digit When using Ademco High Speed program a one 1 in the first location to enable this report a 1555 5555 1 Duress is reported When contact I D is selected program the extended or the second location with the required event code from appendix 1 to enable this report event Programming a 2 in location 93 will report an event 120 Code Pad Panic If activated the siren can be silenced by entering any Arm Disarm code No restore code is reported for this event If both locations are O the Code pad panic double keypress is disabled LOCATION 094 095 PROGRAMMING THE CODE PAD TAMPER FEATURE The DAS DL100 has an optional tamper feature that when enabled will lock out the code pads for 1 minute if 30 random keypresses are made without producing a valid code The desired tamper code should be programmed in locations 094 095 If the control is not programmed for local only the tamper will be communicated Location 094 contains the standard digit and location 095 contains the extended digit When using Ademco High Speed program a one 1 in the first location to enable this report a zone 8 alarm 5555 5551 7 will be reported When contact I D is selected program a one 1 in the extended or the second location to enable this report an event 137 Code Pad Tamper will be reported No restore code is reported for this event If both locations are 0 the tamper feature will not be enabled or reported LOC
35. med in location 126 and a Burglary Alarm B A restores a B R will be transmitted If a 1 is programmed in location 124 and a Fire Alarm F A zone goes into Trouble an F T will be transmitted 30 SPECIFICATIONS OPERATING POWER 16 5 VAC 1 5 AMP Plug Pack AUXILIARY POWER 12 VDC Regulated 500 mA LOOP RESISTANCE 300 Ohms Maximum BUILT IN SIREN DRIVER 4 Ohms Max LOOP RESPONSE Selectable 20mS to 500ms OPERATING TEMPERATURE 32 to 120 degrees F KEYPAD DIMENSIONS 5 50 Wide 4 25 High 850 Deep METAL ENCLOSURE DIMENSION 11 25 Wide 11 25 High 3 50 Deep SHIPPING WEIGHT 9 lbs WARRANTY STATEMENT DIRECT ALARM SUPPLIES GUARANTEES THIS PRODUCT AGAINST DEFECTIVE PARTS AND WORKMANSHIP FOR TWENTY FOUR 24 MONTHS FROM DATE OF PURCHASE IF ANY DEFECT APPEARS DURING THE WARRANTY PERIOD RETURN IT TO DAS POSTAGE PREPAID THE UNIT WILL BE REPAIRED AND RETURNED DAS ASSUMES NO LIABILITY FOR CONSEQUENTIAL OR INDIRECT DAMAGE AND ACCEPTS NO RESPONSIBILITY FOR REPAIRING DAMAGE TO THE PRODUCT CAUSED BY MISUSE CARELESS HANDLING OR WHERE REPAIRS HAVE BEEN MADE BY OTHERS NO OTHER GUARANTEE WRITTEN OR VERBAL IS AUTHORIZED BY OR ON BEHALF OF DIRECT ALARM SUPPLIES BULLETIN IM DL100 B 31 32
36. n should contain a 6 LOCATION 162 PROGRAMMING THE AUTOTEST TIME HOUR TENS DIGIT Location 162 contains the tens digit of the hour that the autotest report is initiated The time is entered in 24 hour time If the desired autotest time is 5 25 PM the 24 hour time is 17 25 so this location should contain a 1 which is the tens digit of the desired hour for autotest If the desired autotest time is 9 36 AM the 24 hour time is 09 36 and this location should contain a O LOCATION 163 PROGRAMMING THE AUTOTEST TIME HOUR ONES DIGIT Location 163 contains the ones digit of the hour that the autotest report is desired The time is entered in 24 hour time If the desired autotest time is 5 25 PM the 24 hour time is 17 25 so this location should contain a 7 which is the ones digit of the hour for autotest If the desired autotest time is 9 36 AM the 24 hour time is 09 36 and this location should contain a 9 LOCATION 164 PROGRAMMING THE AUTOTEST TIME MINUTES TENS DIGIT Location 164 contains the tens digit of the minutes after the hour that the autotest is desired The time is entered in 24 hour time If the desired autotest time is 5 25 PM the 24 hour time is 17 25 so this location should contain a 2 which is the tens digit of the minutes for autotest time If the desired autotest time is 9 36 AM the 24 hour time is 09 36 this location should contain a 3 LOCATION 165 PROGRAMMING THE AUTOTEST TIME MINUTES ONE
37. n with the required event code from appendix 1 to enable this report event programming a three 3 in the extended or the second location will select an event 130 Burglary to be reported The data in the standard location or first location must be left at default or changed to the zone number that is to be reported If locations 104 105 are O this report is disabled LOCATION 106 107 PROGRAMMING THE COMMUNICATOR CODE FOR ZONE 2 Locations 106 107 contain the communicator code to be reported each time zone 2 creates an alarm Location 106 contains the standard digit and location 107 contains the extended digit When using Ademco High Speed program a one 2 in the first location to enable this report a 5155 5555 7 is reported When contact I D is selected program the extended or the second location with the required event code from appendix 1 to enable this report event programming a three 3 in the extended or the second location will select an event 130 Burglary to be reported The data in the standard location or first location must be left at default or changed to the zone number that is to be reported If locations 106 107 are O this report is disabled LOCATION 108 109 PROGRAMMING THE COMMUNICATOR CODE FOR ZONE 3 Locations 108 109 contain the communicator code to be reported each time zone 3 creates an alarm Location 108 contains the standard digit and location 109 contains the extended digit When using Ademco High Speed
38. ng a Binary system With this system the yellow zone 1 LED equals 1 when illuminated The zone 2 LED equals 2 when illuminated The zone 3 LED equals 4 when illuminated The zone 4 LED equals 8 when illuminated Thus if the data in location 000 is 9 the LED for zone 1 1 and zone 4 28 would be illuminated By adding the two values together 12 829 you would determine that the data in location 000 is 9 If the data in location 000 is 6 the LEDs for zone 2 22 and zone 3 24 would be added 2 4 6 indicating the data in that location to be 6 If no LED s are illuminated the location contains a 0 To advance from location 000 through 255 press the key To go to a specific location press the location number followed by the key The yellow LED s will then display the data in that location Data is changed by entering a number between 0 and 15 followed by data enter Review the examples in figure 1 on the following page Important Function Codes 9 5 0 When in the program mode this function code can be used to write original factory default codes into the DL100 9 3 0 This function code is used to exit the programming mode after it was accessed via the Code Pad 1 IMPORTANT Before programming the DL100 for the first time enter the Go To Program Code 9 7 1 3 from the Code Pad followed by the factory default function code 9 S 0O The panel defaults will now match this inst
39. not delay 60 seconds before accepting open or short inputs from any zone If a 0 is programmed sensors on all zones are allowed 60 seconds to stabilise at power up or after exiting the program mode After 60 seconds the DL 100 will once again accept loop opens or shorts as an alarm condition This 60 Second period will also be initiated after a watchdog circuit reset condition LOCATION 137 IMMEDIATE RESTORE BY ZONE If a 1 is programmed in location 137 restoral signals will follow the restore condition and report restores immediately after the condition has unfaulted A non extended format will not send a restore message until all zones and trouble conditions have restored If this location contains a O the restore signal or signals will be reported only after siren timeout LOCATION 138 NO ARMING WITH A ZONE BYPASSED If a 1 is programmed in location 138 the DAS DL100 will not arm with any zone bypassed If programmed with a 0 6 of the 6 burglary zones can be bypassed and the DAS DL100 can still be armed 16 LOCATION 139 PROGRAMMING THE QUICK ARM DIGIT The DAS DL100 can be programmed to Quick Arm with digit 3 by programming a one 1 in location 139 A 0 in this location will disable this feature If the Quick Arm digit is the same as the first digit of the Master code user 1 the Door Chime Annunciation feature will not function LOCATION 140 141 RESERVED FOR FUTURE USE LOCATION 142 SIREN BELL TEST FEATURE
40. o 150 seconds 1 10 seconds through 15 2150 seconds For example programming a 2 in this location will produce an exit delay of 20 seconds Note A 0 entry is treated as 0 seconds Programming a 6 in this location will produce an exit delay of 60 seconds Factory default is 60 seconds LOCATION 077 PROGRAMMING THE SIREN SHUTDOWN RECYCLE TIMEOUT Location 077 contains the number of 2 minute increments in the automatic cutoff time The automatic cutoff time can be programmed in 2 minute increments from 2 to 30 minutes 1 2 min thru 15 30 min For example programming a 2 in this location will produce an automatic cutoff time of 4 minutes Programming a 6 in this location will produce an automatic cutoff time of 12 minutes 10 LOCATIONS 078 085 PROGRAMMING THE ZONE TYPES Locations 078 through 085 contain a number identifying the characteristics of each of the 8 zones Location 078 corresponds to zone 1 and location 085 corresponds to zone 8 Each zone will factory default according to the programming worksheet To program zone characteristics other than the default values program a number from 1 to 9 based on the characteristics in the list below NUMBER ZONE CHARACTERISTICS DESCRIPTION 1 DAY ZONE A trip on a Day zone will produce an instant alarm when armed and activate the code pad sounder when disarmed 24 HOUR A trip on a 24 Hour zone will produce an instant alarm when the DAS DL100 is armed or disarmed
41. ode to be reported each time zone 5 creates an alarm Location 112 contains the standard digit and location 113 contains the extended digit When using Ademco High Speed program a one 5 in the first location to enable this report a 5555 1555 7 is reported When contact I D is selected program the extended or the second location with the required event code from appendix 1 to enable this report event programming a three 3 in the extended or the second location will select an event 130 Burglary to be reported The data in the standard location or first location must be left at default or changed to the zone number that is to be reported If locations 112 113 are O this report is disabled LOCATION 114 115 PROGRAMMING THE COMMUNICATOR CODE FOR ZONE 6 Locations 114 115 contain the communicator code to be reported each time zone 6 creates an alarm Location 114 contains the standard digit and location 115 contains the extended digit When using Ademco High Speed program a one 6 in the first location to enable this report a 5555 5155 7 is reported When contact I D is selected program the extended or the second location with the required event code from appendix 1 to enable this report event programming a three 3 in the extended or the second location will select an event 130 Burglary to be reported The data in the standard location or first location must be left at default or changed to the zone number that is to be reported If
42. of the exit delay will become isolated All zones that become secured before the end of the exit delay will become active in the system Partial Arm Entry Guard This unique home level arming allows you to remain inside your home and only arm areas that are not occupied For example Night Arming Group Isolate Zones can be programmed to isolate as a group when the button is pressed during the exit delay This feature is enabled in Locations 244 249 Assigning Special Characteristics For Zones beginning on page xx of this manual Dynamic Battery Test When enabled in location 203 the DL 100 can be programmed to perform a dynamic battery test for a selected duration at the preselected time Quick Arm If programmed in location 139 the DL 100 can be armed by entering a one button Quick Arm code which is 3 Auto Arming If programmed in location 202 the DL 100 will automatically arm the system at a specific time locations 198 201 if it has not already been armed by a system user Chime Feature If chime zones are selected pressing the 1 from the code pad will enable this feature Smoke Detector Reset If programmed in location 143 the key on the code pad can be used to reset smoke detectors Auxiliary Outputs The DL 100 has four auxiliary outputs that can be activated by ten different conditions see locations 145 148 Loop Response Time The DL 100 has a programmable loop response time from 20mS up to 500mS see
43. om 10 to 150 seconds 1 10 seconds thru 15 150 seconds Note A 0 entry is treated as zero 0 seconds If the exit delay time in this location is less than that of location 076 this secondary delay will follow the amount of time in location 076 LOCATION 180 PROGRAMMING THE LOOP RESPONSE TIME Location 180 is used to program the loop response time for all zones programmed as fast loop response in locations 186 193 The response time is equal to 20 milliseconds times the number programmed in this location 1 20 milliseconds and 5 100 milliseconds If this location contains a O the loop response time will be 500 milliseconds LOCATION 181 AUTOTEST SUPPRESSION Programming a 1 in location 181 will cause the DL100 to suppress anautotest report if the communicator has sent any report since the last autotest Programming a 0 factory default will cause all autotest reports to be sent LOCATION 182 183 FORMAT OVER RIDE LOCATIONS 184 185 RESERVED FOR FUTURE USE LOCATIONS 186 191 ASSIGNING SPECIAL CHARACTERISTICS FOR ZONES 1 6 Locations 186 191 are used to assign individual characteristics for each of zones 1 6 These locations can be used to enable or disable the chime feature restore reporting bypass feature and fast loop response for each of the individual zones 1 6 To enable the features enter a binary number according to the following chart VALUE CHARACTERISTIC VALUE CHARACTERISTIC NO FEATURE SELECTED CHIM
44. ported If this location contains a 0 zone Isolate will not be reported 14 LOCATION 126 PROGRAMMING THE COMMUNICATOR CODE FOR RESTORAL Location 126 contains the communicator code that will be sent for restoral of a zones and or system report events When using Ademco High Speed program a one 1 in this location to enable this report When contact I D is selected program a one 1 in this location to enable this report If this location contains a O norestorals will be reported LOCATION 127 PROGRAMMING THE COMMUNICATOR CODE FOR CANCEL EXCEPTION OPENING Location 127 contains the communicator code that will be sent for cancel The cancel code programmed in this location will be sent if an arm disarm code is entered after a trip on zones 1 through 6 has been reported excluding 24 hour zones After a cancel has been reported no loop restorals will be transmitted on non 24 Hour zones When using Ademco High Speed program a one 1 in this location to enable this report the opening event will be reported with the user code number used When contact I D is selected program a one 1 in this location to enable this report the opening event will be reported with the user code number used This feature can not be enable when Open Close reporting is also enabled If this location contains a 0 cancel is disabled LOCATION 128 PROGRAMMING THE COMMUNICATOR TO ABORT Location 128 contains the number of 3 second increments in the communica
45. ry Output Terminals Current limited to 250 micro amps positive and 20 mA negative Connect one side of zone 1 loop The other side of loop to common terminal 6 Open or short causes alarm Common Terminal Connect one side of zone 2 loop The other side of loop to common terminal 6 Open or short causes alarm See Terminal Drawing and repeat the above sequence for zones 3 6 Connect code pad wires as follows yellow to terminal 17 green to terminal 18 black to terminal 19 red to terminal 20 70 metres maximum run with 7 020 cable 120 metres maximum run with 14 020 cable Home run cable to each code pad Siren driver output to speaker s speaker rating should be 15 watt at 8 or 16 ohm or 30 40 watt at 4 8 or 16 ohms If siren driver disable is selected in location 132 output becomes voltage output 12VDC 1 Amp maximum load Smoke detector power 12VDC 100 mA maximum For those jurisdictions which allow the Priority zone to be used with smoke detectors Auxiliary Power regulated 12VDC 500 mA maximum Earth Ground connect to a cold water pipe or 6 to 10 foot driven rod AC input connect a 16 5V 1 5 Amp Plug Pack Standby battery leads black and red connect to a 12VDC lead acid rechargeable battery Do not connect to a dry cell battery FUSE DESCRIPTION FUSE NO DESCRIPTION 1 AMP Code pad 2 AMP Siren Driver 1 AMP Aux Power amp Smoke Detector Power PROGRAMMING The DL100 can be place
46. s you to remain inside your home and only arm areas that are not occupied To enable this mode location 131 must be programmed correctly When Partial Arm is enabled zones programmed with a 2 will be monitored in Partial Arm For zones to be isolated in this mode do not program a 2 in this location When Partial Arm is enabled pressing the 2 at the code pad and waiting five seconds will arm the DL 100 in this mode The disarming method is determined in location 131 NOTE The Partial Arm entry time will follow your primary entry time Group Isolate Zones can be programmed to isolate as a group when gt 9 is pressed prior to arming This feature can be enabled in conjunction with the Partial mode feature Programming a 4 in these locations will enable the selected zone to be part of the group isolate DATA CHARACTERISTIC PARTIAL ARM ENTRY GUARD MONITORED GROUP ISOLATE PARTIAL ARM ISOLATED GROUP ISOLATE PARTIAL ARM ENTRY GUARD MONITORED NO GROUP ISOLATE PARTIAL ARM ISOLATE LOCATIONS 250 251 RESERVED FOR FUTURE USE LOCATION 252 253 PROGRAMMING TO REPORT CODE PAD AUXILIARY 3 The DAS DL100 has the ability to report a Silent Auxiliary 3 code each time the 7 and 9 keys are pressed simultaneously on the code pad This feature is generally used as a manual communicator test The desired Auxiliary 3 code is programmed in locations 252 253 When using Ademco High Speed program a one 1 in the first location to
47. to be one of nine different types including 24 Hour Interior Follower and Day zone Each zone is individually annunciated and can be bypassed from the code pad See page 11 for a description of all zone types Read the OPERATORS MANUAL before you begin the installation for the best overall description of how the DAS DL100 functions After installation of the security system complete the information on page 1 of the operators manual and explain the system operation to all security system owners operators Standard Parts List The DAS DL100 is shipped with the parts listed below PART DESCRIPTION PART NO MASTER CONTROL PANEL W O CODE PAD FS4657 33K 1 2 WATT E O L RESISTORS EOL 33 TELEPHONE LEAD FS4596 INSTALLATION MANUAL IM DL100 OPERATORS MANUAL OM DL100 Optional Parts List The following parts are available for use with the DAS DL 100 6 LED REMOTE CODE PAD PROGRAMMER WITH DIGITAL NUMERIC DISPLAY FS4597 SMART PROGRAMMER WITH LCD DISPLAY FS4610 12VDC 6AH BATTERY FS4312 DOWNLOADING SOFTWARE PACKAGE FS4532 FEATURE DEFINITIONS Secondary Exit Delay Used most often for garage doors this zone type is a second entry exit delay zone that has its own delay times independent of the standard entry exit delay zone Auto Isolate Enable When enabled in location 197 the DL 100 can be armed with zones violated lacking a green READY light on the code pad Under this condition all zones that are not secure at the end
48. tor abort feature which is programmable from 3 to 45 seconds 1 3 seconds through 15 45 seconds For example programming a 2 in this location will produce an abort time of 6 seconds The DL 100 will abort the alarm report on any non 24 hour zone if an arm disarm code is entered within the abort time If this location contains a 0 the DL 100 will not abort any reports LOCATION 129 PROGRAMMING FOR SILENT PANIC HOLD UP Location 129 is used to silence the audible output for a panic hold up alarm Programming a 1 in thi location will silence the audible output during a panic hold up alarm If this location contains a 0 the DAS DL100 will have an audible panic hold up output LOCATION 130 LIMITED SIREN AND OR COMMUNICATOR OUTPUTS Location 130 is used to limit the sirens or the communicator or both to one output per zone during a single arming cycle The following table will indicate the value to be programmed in location 130 to give the DL100 the desired characteristics Factory default is 1 once per zone for the siren and unlimited reports for the communicator VALUE DESCRIPTION SIRENS AND COMMUNICATOR NOT LIMITED 2 COMMUNICATOR ONE REPORT PER ZONE SIREN NOT LIMITED SIREN ONCE PER ZONE COMMUNICATOR NOT LIMITED SIREN AND COMMUNICATOR LIMITED TO ONCE PER ZONE LOCATION 131 AUTOMATIC BYPASS INSTANT ARMING PARTIAL MODE SECURITY FEATURE Location 131 is used to enable automatic Instant Arming or Partial Arm
49. uxiliary outputs to activate for 10 seconds each time a Fire Panic or Burglary activates Programming a 0 in location 132 will cause the Burg and Panic outputs to activate when the yelping siren is on and the Fire Auxiliary output to activate when the steady siren is on LOCATION 133 L E D EXTINGUISH FEATURE Code pad LEDs with the exception of the A C LED will be extinguished after 60 seconds of code pad inactivity if a 1 is programmed in location 133 The LEDs will become illuminated immediately upon a keypress or alarm condition LOCATION 134 ENTERING THE NUMBER OF DIAL ATTEMPTS Location 134 is used to enter the number of dial attempts 1 to 15 attempts the communicator will try for the appropriate phone number s before ending the notification process If this location contains an 8 the communicator will make 8 attempts to the first number and then eight attempts to a second number if a second number is programmed as backup LOCATION 135 POWER UP CONDITION If a 1 is programmed in location 135 the DAS DL100 will power up disarmed if there is a total power shutdown and battery failure If a 2 is programmed in this location it will power up armed If this location contains a 0 the DAS DL100 will maintain the condition it was in at power down A watchdog circuit reset will cause the DAS DL100 to reset to the selected condition LOCATION 136 POWER UP DELAY If aone 1 is programmed in location 136 the DAS DL100 will
50. wnload section for this location to have an effect The callback number will be used according to the following binary scale DESCRIPTION CALLBACK SHOULD NOT OCCUR BEFORE A DOWNLOAD SESSION 8 SITE INITIATED DOWNLOAD IS ENABLED 3 CALLBACK SHOULD NOT OCCUR BEFORE A DOWNLOAD SESSION 8 SITE INITIATED DOWNLOAD IS ENABLED CALLBACK AT AUTOTEST INTERVALS IS ENABLED CALLBACK SHOULD NOT OCCUR BEFORE A DOWNLOAD SESSION CALLBACK AT AUTOTEST INTERVALS IS ENABLED CALLBACK SHOULD NOT OCCUR BEFORE A DOWNLOAD SESSION 8 SITE INITIATED DOWNLOAD IS ENABLED CALLBACK AT AUTOTEST INTERVALS IS ENABLED 8 SITE INITIATED DOWNLOAD IS ENABLED CALLBACK AT AUTOTEST INTERVALS IS ENABLED 22 LOCATIONS 208 209 FORMAT OVER RIDE LOCATIONS 210 243 RESERVED FOR FUTURE USE LOCATIONS 244 249 ASSIGNING PARTIAL ARM GROUP ISOLATE FOR ZONES 1 6 Locations 244 249 are used to assign Partial Arm and Group Isolate zone characteristics for zones 1 6 Location 244 is for zone 1 and 249 is for zone 6 Each zone can have any or all of the following characteristics regardless of the zone type selected in locations 078 085 excluding Fire zones which cannot have isolate capability enabled The table below shows the possible programming data for each zone Factory default is 8 for each of these zones meaning Group Isolate and Partial mode are disabled Partial Arm Entry Guard This unique home level arming mode allow

Download Pdf Manuals

Related Search

Related Contents

  Guía del usuario  Sony VPL-CX3 User's Manual  取扱説明書    EnGenius EOC-3220 EXT WLAN access point  OPERATING INSTRUCTIONS FOR FUEL MANAGEMENT SYSTEM  30 LTC NF Online Portal User Manual 03242014  KGP-913/913D  Scandyna BigPod  

Copyright © All rights reserved. Failed to retrieve file