Installation Manual
Contents
1. Screws l LA Mounting Screws Install the Drive in Drive Case 6 Secure the drive in place using the supplied mounting screws Use the mounting holes on the sides or bottom depending on the design of the drive 7 Slide the drive case cover back on The hardware installation is complete Your Mobile Rack drive case is ready to use Mobile Rack Drive Case Ready for Use Mobile Rack Installation Manual 7 3 1 Using the Mobile Rack Non Hot Swapping Models Models VP 10K VP 10KF Key lock models VP 10K and VP 10KF do not support hot swapping Your computer must be POWERED OFF when the drive is inserted or removed Once installed the removable drive can be used like any other drive To insert the Mobile Rack drive case 1 Make sure the computer is OFF 2 Insert the Mobile Rack drive case with drive installed into the installed Mobile Rack docking case and push firmly until the drive is seated 3 Insert the key and turn key to the right to lock 4 Turn your computer ON The LED on the Mobile Rack should light after a slight delay The installed Mobile Rack device is ready to use o Lock Position 2 _ w To remove the Mobile Rack drive case 1 Turn your computer OFF 2 Insert the key and turn key to the eft to unlock 3 Gently pull on the Mobile Rack handle to slide the drive case out 2 Unlock Position WARNING e DO NOT remove the drive case while the drive is working Damage to data2. cable e Convenient pull out handle e Safety lock feature e Power on off feature Models VP 10KP VP 10KPF and VP1OLS VP 10LSF e LED indicators for power and drive activity e Built in cooling fan Models VP 10LSF VP 10KF and VP 10KPF only e Drive case is interchangeable between all models e Fully compatible with MS DOS Windows 3 11 95 98 NT OS 2 Warp e Dimensions 8 4 D x 5 8 W x 1 6 H Unpacking Your Mobile Rack Before installing the Mobile Rack verify that the following items are included in the carton If any parts are damaged or missing please contact your local dealer or sales representative immediately 1 One Mobile Rack Removable Docking Module 2 Eight mounting screws 3 One user s guide IDE Basics IDE isan acronym for Integrated Device Drive Electronics and is sometimes referred to as an ATA AT Attachment interface It is the most commonly used interface for hard disk drives installed on personal computers Other devices like CD ROM tape optical drives and so on have adapted a variation called ATAPI ATA Packet Inter face and can be intermixed with standard IDE drives because they use the same cabling and electrical interface Most systems today have two IDE channel connectors that are typically referred to as primary and secondary ports Each IDE port can have a maximum of two devices that must be uniquely identified typically by the setting of a jumper as a master or slave dev
3. Mobile Rack For Removable Docking Modules with 3 5 2 5 HDD or Optional for zip SuperDisk LS 120 MO TR 4 Tape or ATA Flash Memory Reader N F fai Tul iit ith i li Model VP 10LS Model VP 10LSF Model VP 10K Model VP 10KF Model VP 10KP Model VP 10KPF Model VP 15 Installation Manual VWiPowkEl We are your DataBridge http www vipower com Table of Contents Tet MTRO GIO ON areen a E UI Seance msanach acct baceu R Unpacking Your Mobile Rack ccccssseeeeeeeeseeeeeeeeeens NB ASICS eat eaten E canenseeance 2 1 Hardware Installation cccccccccccseeeceeeseeeeeeeeseeeeeeeeseeeeees Mobile Rack Components cccccseeeeeeeeeeseeeeeeeeeeeeeeeees Installing Mobile Rack Docking Case ccceeceeeeeees Mounting a Drive in the Drive Case cccceeeeeeeeeeeeeee 3 1 Using the Mobile Rack asura Non Hot Swapping Models cccccssseeeeeeeeeeeeeseeeeeees Hot Swapping Models cccccsecceeeseeeeeeseeeseeeeeeeeeeees PROPRIETARY NOTICE ViPowER Inc makes no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability and fitness for a particular purpose ViPowER Inc shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material This document contains proprietary information w
4. Mobile Rack drive case cover by sliding it towards the back of the unit Slide Cover Off Remove the Drive Case Cover Mobile Rack Installation Manual 5 2 Ifyou plan to install a drive that features removable media such as a zip TR 4 tape MO LS 120 drive or ATA Flash memory reader carefully punch out the center part of the front panel Center Part of Front Panel Removed Remove Front Panel for Removable Media Drives IMPORTANT If you are installing a new hard drive into the Mobile Rack you may need to configure the drive before you install it Refer to the drive manufacturer s docu mentation and configure the drive as Master Cable Select or Slave depending on the configuration of your computer After you complete this installation you may also need to re configure the computer s BIOS Setup to make the drive functional in the system 4 The drive cases 40 pin IDE cable supports 3 5 inch drives Attach the power and IDE cables from the Mobile Rack drive case to the drive The power connector is D shaped to correctly orient the connector The colored stripe on the IDE cable should be closest to the power connector To install a 2 5 inch drive you must purchase a 44 pin to 40 pin connector adapter from your local computer dealer 5 Carefully position the drive inside the drive case 6 Mobile Rack Installation Manual Power Cable Colored Stripe IDE Data Cable Mounting
5. e case out power cf Unlock Position Hy Unlock Position Mobile Rack Installation Manual 9 amp Printed on recycled paper
6. hich is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the written consent of ViPowER Inc The information contained in this document is subject to change without notice IBM is a registered trademark and PC AT are trademarks of International Business Machines Corporation Windows and Windows NT are registered trademarks of Microsoft Corporation All other trademarks belong to their respective owners Patent USA 5694290 Taiwan 126661 amp 129379 Germany Nr 297 15 551 2 amp Nr 297 22 974 5 Japan 3047936 amp 3050489 China ZL 97 2 03156 1 Patent Pending U K France Korea Copyright 1998 by ViPowER Inc 9 98A This manual will guide you through the installation of the VP 10LS and VP 10K Series Mobile Rack Removable Docking Modules Mobile Rack Models VP 10LS IDE interface Latch lock Slide Switch VP 10LSF IDE interface Latch lock Slide Switch with Cooling Fan VP 10K IDE interface Key lock VP 10KF IDE interface Key lock with Cooling Fan VP 10KP IDE interface Key lock Power Switch VP 10KPF IDE interface Key lock Power Switch with Cooling Fan VP 15 IDE interface Drive Case Model Number Code Descriptions for Ordering Information VP 10LS F 1 HOHaROND 2345 6 ViPowER Interface Type 1 IDE 2 SCSI 3 Wide SCSI BOY estates 2 Out Frame 5 In Tray Box 0 Frame Tray Lock Ty
7. ice 2 Mobile Rack Installation Manual 2 1 Hardware Installation The Mobile Rack Docking Module is designed to install in any PC AT or Pentium class computer that hasan available 5 25 inch half height drive bay General instructions for installing the Mobile Rack are given since the design of computer cases varies Refer to your computer s manual whenever in doubt Mobile Rack Components The Mobile Rack is comprised of two components Docking Case VP 12 L S F K P Drive Case VP 15 Mounting Holes Power ON OFF LED Indicator Drive Activity Slide Lock Power Switch LED Indicator Latch Lock Model Mobile Rack Docking Case Mounting Holes Power ON OFF LED Indicator Drive Activity Slide Lock Power Switch LED Indicator Key Lock Model Mobile Rack Docking Case Mobile Rack Installation Manual 3 Power Connector Data Interface Cable Bottom Mounting Holes Handle Side Mounting Holes Removable Front Panel for Removable Media Drives Mobile Rack Drive Case VP 15 with cover removed Installing the Mobile Rack Docking Case l Turn OFF the power to your computer and any other connected peripheral devices Follow the precautions for static electricity discharge e Discharge any static electricity build up in your body by touching a grounded metal surface such as the computer case if plugged in e During installation procedures avoid any contact with internal parts 2 Unplug the powe
8. may result e The Key Lock keyswitch must be in the Lock position when in use This prevents removal while working e Always turn the system power OFF before removing or inserting the drive case 8 Mobile Rack Installation Manual Hot Swapping Models Models VP 10LS VP 10LSF VP 10KP VP 10KPF Latch Lock models VP 10LS and VP 10LSF and Key Power Lock models VP 10KP and VP 10KPF support hot swapping The power to your computer can be ON when the drive is inserted or removed Use the Latch Lock switch or Key Power Lock keyswitch to turn power to the drive ON after inserting it and OFF before removing it To insert the Mobile Rack drive case 1 Insert the Mobile Rack drive case with drive installed into the installed Mobile Rack docking case and push firmly until the drive is seated 2 For models VP 10LS VP 10LSF slide the latch lock left to the lock position For models VP 10KP VP 10KPF insert the key and turn key to the right to lock The LED on the Mobile Rack should light after a slight delay The installed Mobile Rack device is ready to use A power cf A Lock Position Lock Position 2 Sa To remove the Mobile Rack drive case 1 Formodels VP 10LS VP 10LSF slide the latch lock right to the unlock position For models VP 10KP VP 10KPF insert the key and turn key to the eft to unlock Note that the power LED on the Mobile Rack should now be OFF 2 Gently pull on the Mobile Rack handle to slide the driv
9. pe L Latch lock K Key lock Power Switch S Latch Switch P Power IC Switch Cooling Fan F Fan NOTE Although there are certain feature differences between the Mobile Rack models the installation for all models is the same For instructions on how to use your Mobile Rack please refer to the section that applies to your Mobile Rack model 1 1 Introduction Congratulations on your purchase of a Mobile Rack Removable Docking Module The Mobile Rack is the perfect solution for data backup and transporting data between computers It enables portability of 3 5 inch 2 5 inch IDE and ATAPI devices such as hard disk SuperDisk LS 120 MO TR 4 tape zip drives and ATA flash memory readers The Mobile Rack is form fitted for a standard PC AT 5 25 half height bay Its drive case can accept most half height 3 5 and 2 5 drives with separately purchased adapter cables Not being limited by memory size you can install any capacity drive Mobile Rack Installation Manual 1 Features e Compatible with tower or desktop PC external subsystem amp RAID system cases e Enables portable use of hard disk LS 120 MO TR 4 tape zip and other IDE and ATAPI devices e Drive bay module for mounting a 1 0 inch height 3 5 inch or 2 5 inch IDE or ATAPI device in a 5 25 inch drive bay e Supports fixed 3 5 inch hard disk drives and 2 5 inch hard disk drives requires 2 5 inch drive adapter
10. r cord from the back of the computer 3 Remove your computer s cover 4 Remove the computer s front cover plate from the 5 25 inch drive bay you plan to install your Mobile Rack into Remove separate the Mobile Rack drive case from the docking case by lifting the handle and pulling it out Slide the docking case into the 5 25 inch drive bay Mounting a Mounting Screws Screws Docking Case All Models Mounting Screws Install the Mobile Rack Docking Case into the Drive Bay Mobile Rack Installation Manual 7 Attach an existing IDE 40 pin data cable from the system motherboard to the 40 pin connector on the back of the docking case Most connectors are keyed for proper insertion If there is no key orient the cable so the pin 1 colored stripe edge is closest to the power connector 8 Attach an available 4 pin power cable from the system s power supply to the 4 pin connector on the back of the docking case The power connector is D shaped to ensure proper orientation when making the connection Pin 1 ee 40 pin IDE Connector Power Connector Docking Module IDE and Power Connectors 9 Replace the computer s cover and reconnect the power and other external cabling Mounting a Drive in the Drive Case VP 15 Proceed with the following steps to install a 3 5 inch drive device in the Mobile Rack drive case Note a special adapter kit is required in order to install a 2 5 inch drive 1 Remove the
Download Pdf Manuals
Related Search