Home

Installation Manual - JRW Security Services

1. Commissioned See commissioning instructions Disclaimer While every effort has been made to ensure the accuracy of this manual the manufacturer assumes no responsibility or liability for any errors or omissions Due to ongoing development this manual is subject to change without notice 2003 Inner Range Pty Ltd Part No 635507 CONCEPT IQ Combined Installation Manual Rev 1 0 05 03 19 INSTALLATION Connection diagrams provided on the next page Installing the RF Module The Module must be installed on a flat surface in an appropriate secure location See LAN cabling considerations Cut suitable holes in the mounting surface for cable entry if required and the fasteners The base of the plastic enclosure can be used as a template Cut suitable holes in the base and or cover of the enclosure for cable entries as required ACCESS TO THE PCB IS REQUIRED FOR COMMISSIONING THE MODULE INCLUDES ENROLLING THE REMOTES DO NOT FIT THE COVER OR SECURE THE BASE TO THE MOUNTING SURFACE UNTIL THE COMMISSIONING IS COMPLETED When commissioning is completed fit the cover to the base of the enclosure The base of the enclosure can now be installed using appropriate fasteners through the holes provided Connecting and Mounting the RF Module Insert the cabling through your cable entry cutouts Connect the LAN cabling into the Screw Terminal block T2 If the RF Receiver is installed remotely connect the RF Rec
2. Interface amp Programming Key Interface 5 m gt cable as shown on page 1 2 Run the CIQ Upload Download pro gram c9 Programming Key Import FROM Export TO 3 Follow the on screen instructions and PKey PKey prompts Choose Import or Export when amp Logout required and ensure that the correct Computer COM Port is selected from the drop down menu Parts List for 995515 and 995516 when purchased seperately Disclaimer While every effort has been made to ensure the accuracy of this manual the manufacturer assumes no responsibility or liability for any errors or omissions Due to ongoing development this manual is subject to change without notice CONCEPT IQ Combined Installation Manual Rev 1 0 05 03 p27 DTMF Card 995505 The DTMF Card connects directly to the Control Module DTMF Port to provide Telephone remote control DTMF Card Parts List DTMF Card Installation Manual This document 1x 20mm Brass PCB standoff INSTALLATION Remove the screw on the top edge of the Control Module PCB next to the STATUS Lamp Fit the Brass PCB standoff in place of the screw Plug the DTMF Card onto the box header JP10 on the Control Module DTMF PORT Secure the DTMF Card to the standoff using the screw removed from the Control Module Program the required DTMF functions See Programming Manual Programming of Advanced Features
3. TTL Comms Port connect Prog Key Port 0 only RS232 PC connection requires adapter cable 993030 or Printer connection IQ Plus only adapter cable 993030DB25 r Disclaimer 1 The manufacturer amp or it s agents take no responsibility for any damage financial loss or injury caused to any equipment property or persons resulting from the correct or incorrectuse of the system or it s peripherals The purchaser assumes all responsibility in the use of the system and it s peripherals 2 While every efforthas been made to ensure the accuracy of this manual the manufacturer assumes no responsibility or liability for any errors or omissions Due to ongoing development this manual is subject to change without notice CONCEPTIQ Combined Installation Manual Standard LED Terminal 995500V2 The LED Terminal is the main operator interface for the Concept IQ system providing status display of 16 Zone Inputs and 4 Areas along with indication of Power Fault Home Mode and Armed conditions Rev 1 0 05 03 pl Audible button press feedback is provided and the built in Beeper also provides indication of Alarms Entry Exit warnings Auto Arm warning User Operation OK and User Operation Unsuccessful While the system can be programmed via Upload Download software the LED Terminal also provides the ability for the Installer to program all system parameters INSTALLATION Mounting the Terminal The Terminal must be instal
4. Location of Brass PCB standoff JP10 DTMF PORT 4 m F o9 E E 8 Control Module Disclaimer While every effort has been made to ensure the accuracy of this manual the manufacturer assumes no responsibility or liability for any errors or omissions Due to ongoing development this manual is subject to change without notice 2003 Inner Range Pty Ltd Part No 635505 p28 Rev 1 0 05 03 CONCEPT IQ Combined Installation Manual
5. and Battery retainer wisssesQssi O Li A T1 16V AC Power Step 3 connections Step 5 Latch for optional lock T3 Battery connections Step 6 12V 7AH B ition Rear cable entry cutout rud attery position Step 7 12V i Bottom Mounting Holes x 2 Step 4 lt Location of Side Cable entries Step 7 CONCEPTIQ Combined Installation Manual Connection Details Detectors Tamper switch and Fuses LO Rev 1 0 05 03 p9 d Cor 98 Ce Dur rri il 10000 Li 000000 8 3 dE B 3 y t Sw e Be oy A 1 ov T Detector C Tamp 1 1 Alarm Detector 1 1 Alarm 1st Detector 2nd Detector NOTE The 1k EOL Resistor must be fitted at the 2nd Detector ue Minimum Cable spec 14 0 2 Mode 3 Telephone Socket Wiring for Australia 604 Socket 0 to other equipment oo Oe Q 4 604 Cable from zv Concept IQ Control Supplied Module 1 os 2 D o l2 2 PSTN ovo 5 E eme C ipm Line COAT 69 6 wo JP9 F2 PWR Fuse 1A M205 T2 TAMP Dedicated Cabinet Tamper input Tamper switch supplied No End of line resistors necessary T6 and T7 Zone Input connections Single End of Line e g 3k3 Seal Open Cct Alarm Dual
6. Download software the Terminal also provides the ability for the Installer to program all system parameters In addition to these standard functions the RF Enhanced Terminal also provides an interface for the Concept IQ RF Remote Receiver Up to 6 Four button Keyfob Remotes can then be programmed to Arm and Disarm the Areas in the User s Area List Turn Auxiliary 2 on the Control Module On and Off Activate a Panic alarm by pressing any 2 keys simultaneously IMPORTANT NOTES 1 Four Button Keyfob Remotes P N 995508 are purchased separately 2 The Enhanced RF Terminal DOES NOT provide Door Access Control functions Enhanced RF LED Terminal PARTS LIST Concept IQ Enhanced RF LED Terminal 910043 Mounting Backplate 995509 RF Receiver 625500 Zone List Label Installation manual This document SPECIFICATIONS Dimensions Length 132mm Width 85mm Depth 28mm Weight 150 grams Installation Environment Continuous Operating Temp 0 to 50 C Storage Temperature 20 to 70 C Relative Humidity 15 to 85 Non condensing Operating voltage 11V to 14V DC Current consumption Standby 32mA 50mA with 8 LEDs On RF Receiver Part No 995509 Dimensions Length 110mm Width 30mm Depth 10mm Current Consumption 7 5mA LAN CABLING CONSIDERATIONS The Enhanced RF Terminal is one of a number of different types of Concept IQ LAN Modules A maximum of 4 LAN Modules can be connected to the system LAN O
7. NOTES 1 This Firmware is the application which runs in the Control Module it is NOT the Area Zone System Options and User information etc that can be programmed by the Installer or Master User When a Firmware upgrade is performed all the Installer User programmable database is retained 2 If the Firmware Upgrade is performed whilst the system is ARMED the system will DISARM when the FLASH Interface cable is disconnected 3 If the system is monitored System Reset will be reported when the FLASH Interface cable is disconnected Procedure for Reprogramming Upgrading of the Firmware NOTE This procedure requires you to contact Inner Range Technical support for a File Key 1 Obtain a copy of the Concept IQ Flash Programmer program FLDVER EXE 2 Obtain the new version of Firmware for the Concept IQ Control Module Inner Range will forward or e mail a Field file version XIQ of the requested Firmware to the Installer 3 Connect the PC to the Control Module using the Programming Key and Flash Interface and the FLASH Interface cable as shown on page 1 Ensure that the connector on the cable is oriented correctly Pin 1 on the PCB Header labeled FLASH JP8 Run the CIQ Flash Programmer program FLDVER EXE Select the correct COM Port that you are using on the Computer Press the lt CONTINUE gt button and select the Field file version XIQ that was provided by Inner Range You will be prompted for the FILE KE
8. See Perform the Module Setup Security Cable recommended 14 0 2 LAN connections to the Control Module T4 connector CONCEPT IQ Combined Installation Manual Rev 1 0 05 03 p21 5 10 11 Enable Remote Keyfob enrollment programming mode DIPswitches 1 to 6 are used to select the Remote to enrol To enable the first Remote to be enrolled a Set DIPswitch 1 to ON Selects Remote 1 to enrol b Set DIPswitch 7 PGRM to ON Enables Program mode Enrol a Remote Keyfob a Press any key on the Remote LED L1 will flash once to acknowledge that the RF Module has received the data b Press the same key on the Remote again to confirm the data LED L1 will flash three times to confirm that the data has been successfully received twice Through Steps a amp b and the enrolment has been accepted c Set DIPswitch 7 to OFF then Set DIPswitch 1 to OFF Enrol additional RF Remote Keyfobs Follow steps 5 and 6 to enrol up to 5 additional Remotes A total of 6 Remotes can be enrolled Erasing RF Remote Keyfobs To Erase a Remote from the RF Module a Set one of the DIPswitches 1 to 6 to ON Selects the Remote to erase b Set DIPswitch 8 CLR to ON Erases the selected remote LED L1 will flash 3 times slowly Set DIPswitch 8 CLR to OFF d Set the other DIPswitch From switches 1 to 6 to OFF Initialize the LAN If the RF Module has been added to an existing system once the Module is c
9. cable by cutting the wires close to the connector This will leave approximately 30mm flying leads for connection to the Terminal Strip 5mm of insulation from the Red Black and Brown wires to prepare for termination and route the cable to the Enhanced RF Terminal The Blue wire is not used Terminate the Red Black and Brown wires into the LAN OV and Zone1 connections respectively as shown in the diagram opposite Other connections The Zone2 Input and Aux1 Output are not utilized on RF Enhanced Terminals at this time ADDRESSING amp COMMISSIONING Read LAN cabling considerations first 1 Enable Terminal Configuration Mode Method 1 Remove power from the Terminal Hold down the NEXT and HOME keys Re apply power to the Terminal Release the NEXT and HOME keys Method 2 Hold down the NEXT and HOME keys Short the RST Reset link on the rear of the Terminal See diagram on Page 3 Release the NEXT and lt HOME gt keys 2 Note the current Address setting The current Address of the Terminal will be displayed via the Zone 1 to 4 Lamps The Zone Lamp number that corresponds to the current Address will flash 3 Select the new Terminal Address number Press the key that corresponds to the required Address 1 to 4 within 10 seconds then press ENTER 4 Checkthat the current Door Alarm status is Disabled After the Terminal Address has been entered as per Step 3 th
10. to the selected User If the Remote Key is already assigned to another User or is not recognised by the system one long beep will sound to indicate a problem Enter the new PIN Code may not be required A Zone Lamp 1 to 4 OR 1 to 6 will Fast flash to indicate which digit of the PIN code is to be entered As each digit is entered 3 very short beeps will sound to indicate that the entry is accepted and the next Zone Lamp will now Fast flash for the next digit to be entered Enter the new PIN number w w J w 4 or 6 digits then press Three short beeps will sound to confirm the new PIN number has been programmed If the PIN is rejected one long beep will sound to indicate a problem Assign or Change the User Area or Areas Only required if you have a Multi Area System The lt A2 gt Lamp will flash to indicate the system is ready for the Area assignment entry The corresponding Zone Lamps 1 to 4 will indicate the Area s selected Press the Area number for each Area that is to be Assigned or Un assigned to this User When the required Areas have been Selected and or De selected press NOTE Each User programmed into the system can have an RF Remote OR Access Card assigned but not both If a person requires both of these items program two Users into the system for that person Set the options exactly the same for both Users and assign the RF Remote to one of them and the Access Card to the other User Pro
11. End of Line e g 3k3 Seal 10k1 Alarm Open Cct Tamper Short Cct Tamper Zone Doubling 1k Seal 4k3 1st Zone in Alarm 7k8 2nd Zone in Alarm 11k1 1st amp 2nd Zones in Alarm Open Cct Tamper Short Cct Tamper T5 DET and OV Detector Power connections 12V Supply for Detectors and Auxiliary Devices Total combined current sourced from DET and LAN must not exceed 600 milliAmps NOTE Zone Input connections Normally Open Alarm Contacts Normally Open Alarm Contacts e g As often found on Smoke Detectors are wired in the same manner as Normally Closed contacts When programming the Zone Input Option 7 Normally Open in the Zone Options must be selected Addresses 651 Zone 1 to 666 Zone 16 p10 Rev1 0 05 03 CONCEPT IQ Combined Installation Manual Connection Details Power Warning devices amp LAN JP10 DTMF Voice 8 zl Card Port 8 T8 Aux LAN For temporary connection of a Terminal for diagnostic Da H amp m purposes d ni UT TUE eon HEN fi H H 70 al T9 Zone Input S L T Auxiliary Output HILL IM 222222 Expansion Bus Port AC Bx i ZNI OV ZN2 ZN3 OV ZNA Ov T ov t t A TVA Earth boe T4 LAN connections to Terminals Up to 4 Maximum run to furthest LAN Module 100m Total LAN cabling 150m maximum If twisted pair cable is used DO
12. Expander Card must not exceed 600 milliAmps Concept IQ Expander Rev A VE Inner AX3 4 AX6 AX10 2 Zone Input connections Single End of Line Dual End of Line T4 Auxiliary Output connections 995504 Only 1k min LED wiring Note Dropping Resistor can be any 7 value in the range of 1k to around 1k5 e g 2 x 3k3 Resistors in parallel sles T Relay wiring ea NC Relay coil voltage 12V DC O Fit reverse diode across coil LOo 2 No e g 1N4001 1N4004 NOTE ZONE INPUT CONNECTIONS NORMALLY OPEN ALARM CONTACTS Normally Open Alarm Contacts e g As often found on Smoke Detectors are wired in the same manner as Normally Closed contacts When programming the Zone Input Option 7 Normally Open in the Zone Options must be selected Addresses 651 Zone 1 to 666 Zone 16 IMPORTANT NOTE AUXILIARY POWER Total combined current sourced from DET and LAN on the Control Module and ve on the Expander Card must not exceed 600 milliAmps If additional current is required a separate external Power Supply and backup battery must be used to provide power to the required Auxiliary devices and or Detectors e g 994051 2A Power Supply 994055 Short form Power Supply Board 560001 Plug pack For 1A PS or 560004 In line transformer For 2A PS When separate Power
13. F Terminal cannot perform any operations until it is assigned to a User See Step 10 below Program the RF Remote operations When the lt ENTER gt key is pressed the Enhanced Terminal will exit Terminal Configuration Mode Initialize the LAN If a new Terminal is added to an existing system once the Terminal is configured and connected to the system LAN the LAN must be initialized by Removing and Re applying power to the Control Module Remember to disconnect the battery also when removing power Area Assignment RF Enhanced Terminals must be configured for Single Area Mode by defining an Associated Area for the Terminal Addresses 561 Terminal 1 to 564 Terminal 4 See the Programming Manual Program the RF Remote Operations for a USER Adding or Changing a User NOTE RF keyfobs can only be assigned to a USER on Terminal 1 Logon Enter your PIN code Select the first User number to be added or changed Press ex 4 Where is the User number The A1 Lamp will flash to indicate the system is ready for the PIN Code or Wireless Remote Key entry If a PIN code is already programmed for this User the corresponding number of Zone Lamps 4 or 6 will be flashing Enrol the User s Wireless Remote Key Press a button on the Remote Key within 30 seconds of selecting the User number Three short beeps will sound to confirm that the Remote Key has been enrolled and assigned
14. Installation M anual Contents Section One Concept IQ Hardware Overview 1 1 Typical Installation 1 2 Concept IQ Lockable Cabinet 1 3 Connecting Zone Inputs 1 4 Input amp Output Connections 1 5 IQ Expansion Module Section Two Installation Manuals Control Module 995501 995502 Standard LED Terminal 995500 Enhanced LED Terminal 995500EN Enhanced RF LED Terminal 995500V2RF RF Module 995507V2 Expansion Card 995503 995504 Programming Key 995510 Programming Key and Flash Interface 995511 995515 995516 DTMF Card 995505 ee Factory Default PIN Codes User 1 Installer 2345 User 2 Master User 0123 2003 Inner Range Pty Ltd Part No 635501 INST p2 Rev 1 0 05 03 CONCEPTIQ Combined Installation Manual 1 1 Typical Installation Up to 4 LED Terminals To PC for Upload Download Siren Ps E d Strobe To Central Station DTMF module Connector Upto 16 Zone Inputs Control of up to 10 Auxiliary Devices lights sprinklers pumps CONCEPT IQ Combined Installation Manual Rev 1 0 05 03 p3 1 2 Concept IQ Lockable Cabinet IQ lockable cabinet with room for back up battery Cut outs in sides and re
15. NOT combine Clock amp Data on the same pair 4 Core Security Cable recommended 14 0 2 E T5 OUT2 amp DET Auxiliary 2 Output General purpose Aux May be used for Piezo Siren e g Program Aux 2 as Auxiliary Event Type 9 Ext Siren or 0 Int Siren at Address 802 Maximum switched current 200 mA M W Minimum Cable spec 14 0 2 CAUTION 2 Total current sourced from 5 OUT1 amp DET Strobe DET4 and LAN must Auxiliary 1 Output notexceed 600mA Normally used for Strobe e g Assign E edd Auxiliary Event Type 1 at Address 801 1 Maximum switched current 200 mA Minimum Cable spec 14 0 2 T5 SPK amp DET Siren Speaker output Maximum load 8 Ohms Minimum Speaker rating 10 Watts i e 1 x 8 Ohm Speaker only Additional speakers must not be connected in parallel Siren coverTamper switch Normally Closed Minimum Cable spec 14 0 2 NOTE A 6k8 Resistor must be connected between SPK amp DET if Siren speaker not connected Battery cable supplied T3 amp 12V Sealed Lead Acid Battery connection Maximum Battery capacity 7 AH T1 AC 16V AC Input Connect Green Yellow Earth wire to Plug Pack and cable color may vary outside Australia Port 0 amp Port 1 995502 IQ Plus only Serial OUR UEM REM MUR REM HER Rum Rum REM MEM um Rm m ms mm
16. P N 995516 Port 0 extension cable P N 995517 Instruction Manual This document Programming Key and Flash Interface with FLASH Interface cable connected 995515 Flash Interface Cable Parts List O Py FLASH interface cable Instruction Manual This document 995516 Programming Key Interface Cable Parts List gt y Programming Key interface cable STD Instruction Manual This document Concept IQ PC Interface Specifications Length 96mm Width 42mm Depth 24mm Installation Environment Continuous Operating Temp 0 to 50 C FLASH Interface Storage Temperature 20 to 70 C Cable P N 995515 Relative Humidity 15 to 85 Non condensing Ensure that Pin 1 of the cable Connection Options connector aligns PC or Laptop Computer Programming Key with Pin 1 ofthe and Flash Interface PCB Header 2 E B Ue I B ie i 3 OR APO e To 9 Pin Serial Com Port on PC The posts on the DB9 Connector may be removed if required ey Interface Cable P N 995516 2003 Inner Range Pty Ltd Part No 635511 p26 Rev 1 0 05 03 CONCEPT IQ Combined Installation Manual Reprogramming the Flash Memory in a Concept IQ Control Module Firmware version upgrades for the Concept IQ Control Module can be implemented by reprogramming the Flash Memory with a new version of the firmware IMPORTANT
17. Supply is used 1 The Power Supply must be installed close to the Control Module and the OV or VE supply connections of the Power Supply and the Control Module must be connected together using a heavy guage wire 14 0 20 minimum 2 The ve supply connections of any system Module DET LAN or VE must not be connected to ve of the separate Power Supply Disclaimer While every effort has been made to ensure the accuracy of this manual the manufacturer assumes no responsibility or liability for any errors or omissions Due to ongoing development this manual is subject to change without notice p24 Rev 1 0 05 03 CONCEPT IQ Combined Installation Manual Programming Key 995510 The Concept IQ Programming Key is a portable non volatile memory device housed in a convenient key tag The Programming Key connects directly to the Control Module Port 0 and allows the Installer to Upload the system database from the Control Module or Download a system database to the Control Module via a simple key press sequence on the LED Terminal An indicator lamp is provided on the Programming key to monitor data transfer activity and the LED Terminal provides audible indication of Upload Download Successful Failed Programming Key Parts List NOTE The Inner Range Port 0 Programming key Extension Cable P N 995517 Instruction Manual This document is required for the Concept IQ Plus which has both por
18. Y a Check that the CIQ Flash Version is the one with which you wish to reprogram the panel b Contact Inner Range and ask for the FILE KEY to allow you to access this field file You must inform Inner Range of the TRAN ID number to obtain the correct file key The TRAN ID number will be displayed when you attempt to load the Field file 8 After entering the FILE KEY press OK and the preprogramming will commence If it fails immediately check that you have the cable connected correctly to the PC NOTE It takes several minutes to Erase Reprogram and Verify the flash memory 9 Disconnect the cable from the Control Module FLASH Header 10 Disconnect then reconnect power to the Concept IQ Control Module to restart the application 11 Perform some tests to ensure that the Concept IQ System is functioning correctly 12 Press lt CONTINUE gt to reprogram another Concept IQ Control Module or press CANCEL to exit DO ges Uploading Downloading Data from to a Programming Key The Programming Key and Flash Interface also allows the Programming Key to be connected to a Computer This allows the Concept IQ Upload Download software to Export a system database to a Programming Key for subsequent downloading to a Control Module or to another PC or to Import a system database from a Programming Key Export Import Procedure 1 Connect the PC to the Programming Key o x using the Programming Key and Flash File Edit View
19. ame pair Do not apply power to cable until all connections are made and checked Maximum cabling distance from the Control Module to the furthest Module must not exceed 100 metres Maximum total LAN cabling in the system must not exceed 150 metres DO connect the CLK amp DATA wires to the Control Module until all LAN Modules e g Terminals are Commissioned See next page Wiegand Reader connection Note Supports 12V Reader power supply only No 5V supply option The Reader D1 amp DO wires must be connected to LAN OV Zone1 amp Zone2 on the Terminal using Shielded RS232 Data cable e g Tycab DMC6702 Electra EAS7206 Belden 9536 Alpha 1296C etc DO NOT use Twisted pair cable or Security cable under any circumstances NOTE Check that there is sufficient current still available from the LAN power to supply the Reader If not a separate power supply must be used for the Reader power Diodes must be inserted in series with each of the DO and D1 connections Cathode to Reader Ensure that appropriate insulating sleeve is fitted over the Diodes and solder connections Maximum cabling distance from the Reader to the Terminal must not exceed 80 metres Door Reed switch and Request to Exit button REX connections The Normally Open Request to Exit REX button if used is connected between the Zone 1 Input and OV A 6k8 Resistor m
20. ar mounting plate can be used as a template NOTE The Terminal is also designed to be mounted on plasterboard gyprock surfaces using a standard switch plate Mounting Clip e g Clipsal 154 or HPM 712 rear mounting plate can now be installed using appropriate fasteners through the holes provided Remember to insert the LAN cable and other wiring through the cable entry cutout first Connect the LAN wiring into the Screw Terminal block T2 Clip the Terminal onto the rear mounting plate by first locating the tongue at the top of the Terminal into the slot provided by the rear mounting plate then clip the bottom of the Terminal into place ACCESS TO THE TERMINAL PCB IS REQUIRED FOR RF RECEIVER WIRING AND COMMISSIONING INCLUDES ENROLLING THE REMOTES DO NOT CLIP THE TERMINAL ONTO THE REAR MOUNTING PLATE UNTIL ALL WIRING AND COMMISSIONING IS COMPLETED RF Receiver Installation Install the RF Receiver Part No 995509 in a suitable location not more than 10 metres cabling distance from where the Enhanced RF Terminal is installed NOTE A 2 metre cable is supplied with the RF Receiver If convenient it is recommended that the Receiver is installed within 2 metres cabling distance from the RF Terminal If the cabling distance is greater than 2 metres an additional length of cable will be required to extend the length of the supplied cable 4 core security cable is recommended Remove the 4 way connector on the flying end of the
21. ar of cabinet allow for cable entry Tamper switch fitted to right hand side center will alarm if cabinet door is opened or cabinet is removed from wall p4 Rev 1 0 05 03 CONCEPTIQ Combined Installation Manual 1 3 Connecting Zone Inputs Connections for inputs 1 4 showing OV as common Zone Doubling 3K3 1K and 6K8 with Tamper recognition For Zone Doubling WITH tamper recognition the 1K EOL MUST be at the 2nd PIR Cabling MUST be run from the 1st PIR NOT from the panel For Zone Doubling Without tamper recognition the 1K EOL can be anywhere in the line 1K Seal on PIR 1 amp 2 4K3 Alarm PIR1 7K8 Alarm PIR 2 11K1 Alarm PIR 1 amp 2 S C or O C Tamper N N C Alarm Tamper N Contact Panel Connections PA gt N C PIR BN N C Alarm Tamp Contact CONCEPTIQ Combined Installation Manual Rev 1 0 05 03 p5 Siren 8 ohm SPK to DET Only ONE Standard 8 ohm speaker or 2 x 4 ohm in SERIES max SPK load is 8 ohms Auxes SPK or Aux 0 selectable as siren or Aux at Loc 872 Option 7 1 amp 2 OUT 1 amp OUT 2to DET max 200mA each Max current available 600mA Lund bes z pepa 1 Connection for Tamper switch No EOL resistor required M Port 0 Connector for Upload Download or Program Key p6 Rev 1 0 05 03 CONCEPT IQ Combined Installation Manual 1 4 Input amp Output Connections cont Connector for Firmware upgrad ing and fa
22. arm activation instructions If required neatly print the names of any Areas and Zones used in the system in the spaces provided on the label Remove the backing sheet and carefully affix the label to the inside of the keypad cover ensuring that the top of the label is at the hinged end of the cover CONCEPT IQ Combined Installation Manual Rev 1 0 05 03 p17 6 10 Enrol the Remote Keyfobs into the Terminal a Press any key on the first Remote to be enrolled The Terminal will emit a short beep to acknowledge that the Terminal has received the data b Press the same key on the Remote again to confirm the data After successfully receiving the Remote Keyfob data twice Through Steps a amp b the Terminal will emit a long beep to confirm that the enrolment was accepted a Enrol additional RF Remote Keyfobs Repeat step 6 to enrol up to 5 additional Remotes A total of 6 Remotes can be enrolled b Erasing RF Remote Keyfobs Press the lt 9 gt key at any time while in RF Remote Programming mode to erase all Remotes NOTES 1 When 6 Remotes have been enrolled into the Terminal enrolling any additional Remotes will always overwrite the last Remote that was enrolled i e The first 5 Remotes enrolled will not be affected 2 Ifthe RF Terminal does not receive any data from a Remote for 60 seconds the Terminal will automatically exit Terminal Configuration Mode 3 Any Remote that has been enrolled on an R
23. assumes no responsibility or liability for any errors or omissions Due to ongoing development this manual is subject to change without notice 2003 Inner Range Pty Ltd Part No 635510 CONCEPT IQ Combined Installation Manual Rev 1 0 05 03 p25 Programming Key and Flash PC Interface 995511 995515 995516 The Programming Key amp Flash PC Interface is a portable RS232 Interface housed in a convenient D connector shell housing The Interface connects to the DB9 Serial Port on a PC or Laptop computer A choice of interface cables allows connection to 1 The FLASH connector JP8 on the Concept IQ Control Module for in field upgrading of the Firmware Version Cable P N 995515 2 A Concept IQ Programming key This allows Upload Download of a Concept IQ database from to the Programming Key direct from a PC Cable P N 995516 The PC Interface has three indicator lamps The Pwr lamp Red indicates that the device is powered up Tx Green and Rx Red lamps monitor data transfer activity NOTE For an Upload Download direct connection between a PC and Port 0 on the Concept IQ Control Module a Port 0 Interface Cable Part No 993030 must be used The Programming Key and Flash Interface DOES NOT provide this function 995511 Programming Key and Flash Interface Parts List Concept IQ Programming Key and Flash PC Interface FLASH interface cable P N 995515 Programming Key interface cable
24. cable is recommended COMMISSIONING Read LAN Cabling considerations first 1 Configure the DIPswitches for Setup mode Set DIPswitches 1 to 6 all to the ON position 2 Selectthe RF Module setup options Set DIPswitch 7 to the OFF position Selects RF mode Set DIPswitch 8 to the OFF position Disables Door monitoring function 3 Perform the Module Setup Method 1 Remove power from the Module Re apply power to the Module Method 2 Briefly Short the RST Reset link See diagram on Page 3 Almost as soon as the power is re applied or the link has been shorted the LED L1 will Flash quickly 3 times to confirm Setup is complete 4 Configure the DIPswitches for normal operation Set all DIPswitches 1 to 8 to the OFF position LED L1 will flash slowly 2 seconds On 2 seconds Off to indicate normal operation p20 Rev 1 0 05 03 CONCEPT IQ Combined Installation Manual INSTALLATION DIAGRAMS The RF Module with RF Receiver installed RF Receiver PCB mounted onto RF Module header socket JP2 LAN connections and a Remotely installed RF Receiver note only ONE RF Receiver can be connected internally as above or remotely shown below If extending the length of cable between the RF Receiver and the RF Module 4 Core Security Cable is recommended 14 0 2 Totallength mustbe less than 10 RST Reset link 4 Core
25. ctor power connections 995504 Zone amp Auxiliary Expansion Card Incorporates all Zone Expansion card features along with 8 additional low power open collector Auxiliary Outputs and 4 additional 12V Auxiliary power outputs Expansion Card Parts List Zone Auxiliary Expansion Card Installation Manual This document Installation Kit containing 3x 20mm Brass PCB standoff 1 20mm Threaded plastic PCB standoff 1 Pan Head M3x6mm screw 2 6 Way plug on screw terminals 4x 2 Way plug on screw terminals 995504 contains 2 extra 2 Way and 1 x 8 Way plug on screw terminals 10 x 3k3 End of line resistors 8 x Zone Inputs 2 x Spare orange orange black brown brown 10 x 6k8 End of line resistors 8 x Zone Inputs 2 x Spare blue grey black brown brown INSTALLATION Remove all power to the Control Module Remember to disconnect the Battery See Note 1 below Remove the 3 screws along the bottom edge of the Control Module PCB The screws adjacent to T4 T6 amp T2 Fit the 3 Brass PCB standoffs in place of these 3 screws Fit the Threaded plastic PCB standoff into the mounting hole on the Control Module PCB next to T8 AUX LAN Plug the Expander Card onto the box header T9 on the Control Module EXT PORT Secure the Expander Card to the 4 standoffs using the 3 screws removed from the Control Module and the additional screw provided in the Installation kit Connect the additional Zone Inp
26. ctory default cf NEN 5 299 SA DTMF Port for domestic Ce dialling or remote telephone access mesesmeec LE LEERY HDD additional 8 zone inputs and or 8 auxiliary outputs 8 Auxiliaries AX3 AX10 maximum 200mA each 8 zone Inputs ZN9 ZN16 CONCEPT IQ Combined Installation Manual Rev 1 0 05 03 p7 Control Module 995501 995502 Contents Control Module e LER LERRA EI ERREUR HH BERE IEEE RE Rn 1 eR 1 Installation Procedure nice rne ener etg eri er i x 2 Connection Details Zone Inputs Detectors Tamper switch and FUSES 3 Mode Telephone line connection 3 Connection Details Power Warning devices amp LAN ssssseeeeneeneneenen 4 Control Module Parts List Control Module PCB mounted in metal enclosure User Manual Installation Manual This document Installation Kit containing Contents may vary outside Australia 4 x Pan Head Self tapping screws 4x6mm Used to secure the enclosure cover 5 x plastic D bungs Must be fitted to all unused cable entry cutouts in the cover Telecom Line cord Note Non standard configuration Only suitable for use with this product 10 x 3k3 End of line resistors orange orange black brown brown Used for Single EOL Dual EOL Zone Doubling 10 x 6k8 End of line resistors blue grey black brown brow
27. e display will now show the current Door Alarm enable status 0 Disabled Default 1 Enabled If the Door Alarm status is Enabled press the 0 key within 10 seconds to Disable 5 Enter RF Remote Keyfob enrolling mode While the Door Alarm status is being displayed Press the lt 2 gt key within 10 seconds to enter RF Remote Keyfob enrolling mode All 4 of the Area LEDs will flash to indicate that programming mode is enabled p16 Rev 1 0 05 03 CONCEPT IQ Combined Installation Manual INSTALLATION DIAGRAMS o erm 000 concept ia e LED Terminal wp v P 935500 Rev B WE 0 c3 s Izd Ifextending the length of cable between the RF Receiver and the RF Enhanced Terminal L3 4 Core Security Cable is recommended 14 0 2 Total length mustbe less than 10 metres A U L Red LAN connections to the om J 9 Control Module 4 connector 4 Core Security Cable recommended 14 0 2 RST Reset link Either link can be used See Enable Terminal Configuration Mode Method 2 Zone List label fitted to a ees inside of keypad cover Lp A E ga d TO gue _____ _ Zone List Label 7 15 eS op Medical A self adhesive label is provided that can be used to provide Area CD amp COR 80 and Zone information and Emergency al
28. ecommunications systems Cables must be protected at the entry points by grommets or by allowing the conduit to protrude into the cabinet The D Bungs provided must be fitted to all unused cable entry cutouts DO NOT connect the LAN CLK amp DATA wires to the Control Module until all LAN Modules e g LED Terminals are Commissioned 8 Diagnostics The STATUS Lamp on the Control Module can be used to assist with troubleshooting and testing SLOW FLASHING MicroProcessor OK Running FAST FLASHING Controller is Dialing NOT FLASHING MicroProcessor Not running OR Programming Key Upload or Download in progress 9 Cover In order to comply with regulations the cover must always be correctly re fitted following any installation or maintenance work Engage the hinges on the Left hand side and fasten the cover tightly to the cabinet using all four 4 of the screws provided Screw holes are located on both edges of the two Right hand side corners STATUS Lamp Top mounting holes x2 Step 8 Step 4 JP9 Mode 3 Line Socket Port 1 Serial Comms Port E sE for connection to Telecom ahs IQ des ei i Li 7 Bg Line Special cable dB d E jH Ej E 3 B supplied must be used 0 5 f vor e p Port Noam fo Gobo amp Tamper switch bracket Prog Key 9 PEITTTIT
29. eiver wiring into the LAN OV and Zone1 connections respectively on the Screw Terminal block T2 as shown in the diagram opposite The Blue wire is not used Other connections The Zone2 Input and Aux1 Output are not utilized on RF Modules Installing the RF Receiver into its housing to use remotely only if required Remove the 3 small countersunk screws from the RF Receiver housing Carefully remove the RF Receiver PCB from the Right angle header socket JP2 Place the clear plastic LED Lens onto the PCB Connect the cable to RF Receiver PCB pin 1 marked on header re assembly the housing If the RF Receiver is being installed remotely Install the Receiver in a suitable location not more than 10 metres cabling distance from where the RF Module is installed NOTE A 2 metre cable is supplied with the RF Receiver If convenient it is recommended that the Receiver is installed within 2 metres cabling distance from the RF Module Remove the 4 way connector on the flying end of the cable by cutting the wires close to the connector This will leave approximately 30mm flying leads for connection to the RF Module Strip 5mm of insulation from the Red Black and Brown wires to prepare for termination and route the cable to the RF Module The Blue wire is not used If the cabling distance is greater than 2 metres an additional length of cable will be required to extend the length of the supplied cable 4 core security
30. er Data inputs and REX Door Sealed INSTALLATION Connection diagrams provided on the next page Mounting the Terminal IMPORTANT Enhanced Terminals must be installed on the inside secure side of the Door to be controlled The Terminal must be installed on a flat vertical surface in an appropriate location Ensure that the display will be at or slightly below eye level for all Users Remove the rear mounting plate from the back of the Terminal Cut suitable holes in the mounting surface for cable entry and the fasteners The rear mounting plate can be used as a template NOTE The Terminal is also designed to be mounted on plasterboard gyprock surfaces using a standard switch plate Mounting Clip e g Clipsal 154 or HPM 712 The rear mounting plate can now be installed using appropriate fasteners through the holes provided Remember to insert the LAN cable and other wiring through the cable entry cutout first Connect the wiring into the Screw Terminal block T2 Clip the Terminal onto the rear mounting plate by first locating the tongue at the top of the Terminal into the slot provided by the rear mounting plate then clip the bottom of the Terminal into place LAN connection A maximum of 4 LAN Modules can be connected to the system LAN Recommended cable is 4 core or 6 core security cable 14 0 20 NOT twisted pair Twisted pair cable e g Category 5 may be used however DO NOT combine Clock amp Data on the s
31. gramming can be found in the Programming manual or in the User s manual p18 Rev1 0 05 03 CONCEPT IQ Combined Installation Manual RF Module 995507V2 The RF Module provides a convenient interface for Wireless Keyfob Remote Control in Concept IQ systems The Module connects to the Concept IQ LAN and can be installed in a suitable location up to 100 metres cabling distance from the Control Module This allows a greater degree of flexibility for optimising the location of the RF Receiver for the best coverage A Concept RF Receiver is connected to the RF Module by one of 2 methods The Receiver is mounted on board by connecting directly into a Header socket provided as supplied The Receiver is installed in a suitable location up to 10m cabling distance from the RF Module Optional Four button Remotes can then be used to Arm and Disarm the Areas in the User s Area List Turn Auxiliary 2 on the Control Module On and Off Activate a Panic alarm by pressing any 2 keys simultaneously IMPORTANT NOTES 1 The RF Module Address is hard coded to Terminal Address 4 and cannot be changed Only one RF Module can be installed in a Concept IQ system Ensure that no LED Terminals or other Modules are programmed to Address 4 2 The RF Module DOES NOT provide Door Access Control functions at this time 3 The Four Button Keyfob Remotes P N 995508 are purchased separately 4 The RF Receiver P N 995509 is included and mounted o
32. l Pwr to Unlock Use NO From Lock Power Supply To Lock Strike LAN connections to ADDRESSING amp COMMISSIONING Read LAN connection first the Control Module 1 T4 connector Enable Terminal Configuration Mode Method 1 Remove power from the Terminal Hold down the NEXT and lt HOME gt keys Re apply power to the Terminal Release the NEXT and HOME keys Method 2 Hold down the NEXT and HOME keys Short the RST Reset link on the rear of the Terminal Release the NEXT and HOME keys Note the current Address setting The current Address of the Terminal will be displayed via the Zone 1 to 4 Lamps The Zone Lamp number that corresponds to the current Address will flash Select the new Terminal Address number Press the key that corresponds to the required Address 1 to 4 within 10 seconds then press ENTER Note the current Door Alarm enable status After the Terminal Address has been entered as per Step 3 the display will now show the current Door Alarm enable status 0 Disabled 1 Enabled Default Enable Disable Door Alarm If an Enhanced Terminal is required to generate a Door Alarm for Door Forced or Door Held conditions then Door Alarm must be enabled for that Terminal To Enable or Disable select the option required 0 or 1 within 10 seconds then press ENTER When the ENTER key is pressed the Enhanced Terminal will now exit Te
33. led on a flat vertical surface in an appropriate location Ensure that the display will be at or slightly below eye level for all Users Remove the rear mounting plate from the back of the Terminal Cut suitable holes in the mounting surface for cable entry and the fasteners The rear mounting plate can be used as a template NOTE The Terminal is also designed to be mounted on plasterboard gyprock surfaces using a standard switch plate Mounting Clip e g Clipsal 154 or HPM 712 84mm mounting centres The rear mounting plate can now be installed using appropriate fasteners through the holes provided Remember to insert the LAN cable and any other wiring through the cable entry cutout first Connect the wiring into the Screw Terminal block T2 Clip the Terminal onto the rear mounting plate by first locating the tongue at the top of the Terminal into the slot provided by the rear mounting plate then clip the bottom of the Terminal into place LAN connection A maximum of 4 LAN Modules can be connected to the system LAN The LAN must be connected as follows Recommended cable is 4 core or 6 core security cable 14 0 20 NOT twisted pair Twisted pair cable e g Category 5 may be used however DO NOT combine Clock amp Data on the same pair Do not apply power to cable until all connections are made amp checked Maximum cabling distance from the Control Module to the furthest Module must not exceed 100 metres Maximum t
34. n Used for Dual EOL or Zone Doubling 10 x 1k End of line resistors brown black black brown brown Used for Zone Doubling Tamper switch Tamper switch bracket 2x 6 Way plug on screw terminals Only for PCBs that do not have fixed terminal blocks fitted 1x 3 Way plug on screw terminals Only for PCBs that do not have fixed terminal blocks fitted 5 x 2 Way plug on screw terminals Only for PCBs that do not have fixed terminal blocks fitted 2 x 6 3mm Tamper switch connectors Battery connection lead 220mm pre assembled 1x 2 Amp M205 20mm Fuse Spare Electrical Specifications Power Supply I P Plug pack Mains Supply 240V AC 10 10 50 Hertz Plug pack Output 16V AC 1 0 Amperes PCB AC Input Voltage 16V AC Battery Capacity 12V 7AH Sealed Lead Acid Battery DC Operating Voltage Batt I P 9 5 14 V DC Low Battery alarm activated at 11 2V 0 3V Battery Input Fuse F1 5 Ampere Power Supply O P Current Total combined current required by devices connected to DET and LAN must not exceed 600 milliAmps Fuse Protection F2 2 Ampere DET and LAN Auxiliary Outputs OUT1 Strobe OUT2 Max switched current 200mA per Auxiliary Open Collector Siren Output SPK Maximum Load 8 Ohms i e 1 x 8 Ohm Speaker only Additional speakers must not be connected in parallel NOTES 1 ALWAYS REPLACE FUSES WITH THE SAME FUSE TYPE AND VALUE 2 See data supplied with detectors and
35. n board its plastic housing and cable are supplied so that the receiver can be mounted externally if required RF MODULE PARTS LIST Concept IQ RF Module mounted in Plastic enclosure complete with RF Receiver Installation kit containing 3x 1N4004 Diode 2x 6 8k Resistor 4x M2 5 x 5 screws Installation manual This document RF Receiver plastic housing and cable SPECIFICATIONS Dimensions PCB Length 89mm Width 74mm Depth 13mm Enclosure Length 135mm Width 83mm Depth 44mm Weight 160 grams 140 grams without RF Receiver fitted Operating voltage 11V to 14V DC Current consumption 56mA 48mA without RF Receiver fitted Installation Environment Continuous Operating Temp 0 to 50 C Storage Temperature 20 to 70 C Relative Humidity 15 to 85 Non condensing LAN CABLING CONSIDERATIONS A maximum of 4 LAN Modules can be connected to the system LAN Recommended cable is 4 core or 6 core security cable 14 0 20 NOT twisted pair Twisted pair cable e g Category 5 may be used however DO NOT combine Clock amp Data on the same pair Do not apply power to cable until all connections are made and checked Maximum cabling distance from the Control Module to the furthest Module must not exceed 100 metres Maximum total LAN cabling in the system must not exceed 150 metres DO NOT connect the CLK amp DATA wires to the Control Module until all LAN Modules e g Terminals are
36. nfigured and connected to the system LAN the LAN must be initialized by Removing and Re applying power to the Control Module Remember to disconnect the battery also when removing power Area Assignment Additional system programming allows Terminals to be configured for Multi Area Mode or for Single Area Mode by defining an Associated Area for each Terminal Addresses 561 to 564 2003 Inner Range Pty Ltd Part No 635500 p12 Rev 1 0 05 03 CONCEPTIQ Combined Installation Manual Enhanced LED Terminal 995500EN The Enhanced LED Terminal is a versatile operator interface for the Concept IQ PLUS system providing standard LED Terminal functions along with an interface for Door Access Control The Terminal provides status display of a single Associated Area and up to 16 Zone Inputs along with indication of Power Fault Home Mode and Armed conditions Audible button press feedback is provided and the built in Beeper also provides indication of Alarms Entry Exit warnings Auto Arm warning User Operation OK and User Operation Unsuccessful While the system can be programmed via Upload Download software the Terminal also provides the ability for the Installer to program all system parameters In addition to these standard functions the Enhanced Terminal also provides Single low power open collector Door Unlock Output Programmable un lock time 0 to 60 seconds Two multi purpose inputs configurable as Wiegand Read
37. onfigured and connected to the system LAN the LAN must be initialized by Removing and Re applying power to the Control Module Remember to disconnect the battery also when removing power Area Assignment The RF Module must be configured for Single Area Mode by defining an Associated Area for the Terminal Addresses 564 Terminal 4 See the Programming Manual Program the RF Remote Operations for a USER Adding or Changing a User NOTE RF keyfobs can only be assigned to a USER on Terminal 1 Logon Enter your PIN code v Select the first User number to be added or changed Press ex 4 Where is the User number The A1 Lamp will flash to indicate the system is ready for the PIN Code or Wireless Remote Key entry If a PIN code is already programmed for this User the corresponding number of Zone Lamps 4 or 6 will be flashing Enrol the User s Wireless Remote Key Press a button on the Remote Key within 30 seconds of selecting the User number Three short beeps will sound to confirm that the Remote Key has been enrolled and assigned to the selected User If the Remote Key is already assigned to another User or is not recognised by the system one long beep will sound to indicate a problem Enter the new PIN Code may not be required A Zone Lamp 1 to 4 OR 1 to 6 will Fast flash to indicate which digit of the PIN code is to be entered As each digit is entered 3 very short beeps
38. otal LAN cabling in the system must not exceed 150 m DO NOT connect the CLK amp DATA wires to the Control Module until all LAN Modules e g Terminals are Commissioned See below ADDRESSING amp COMMISSIONING Read LAN connection first 1 Enable Terminal Configuration Mode Method 1 Remove power from the Terminal Hold down the NEXT and HOME keys Re apply power to the Terminal Release the NEXT and lt HOME gt keys Method 2 Hold down the NEXT and lt HOME gt keys Short the RST Reset link on the rear of the Terminal Release the NEXT and lt HOME gt keys e om Concept IQ Q2 N1210 SWI LED Terminal 995500 Ro 8 LI A a 1t 4 5 38 07 af eL H 1999 8 nsr 4Core Security Cable recommended 14 0 2 LAN connections to the Control Module T4 connector Note the current Address setting The current Address of the Terminal will be displayed via the Zone 1 to 4 Lamps The Zone Lamp number that corresponds to the current Address will flash Select the new Terminal Address number Press the key that corresponds to the required Address 1 to 4 within 10 seconds then press lt ENTER gt When the ENTER key is pressed the Terminal will exit Terminal Configuration Mode Initialize the LAN If a new Terminal is added to an existing system once the Terminal is co
39. output devices for current consumption Mechanical Specifications Dimensions Height 260 mm Width 265 mm Depth 80 mm Weight 4 2 kg Cabinet amp cover PCB and 7AH battery Plug pack 0 6kg Environmental Specifications Continuous Operating Temperature 0to 50 C Storage Temperature 20 to 70 Relative Humidity Non condensing 15 to 85 2003 Inner Range Pty Ltd Part No 635501V2 p8 Rev 1 0 05 03 CONCEPT IQ Combined Installation Manual Installation Procedure 1 Installer The system must be installed and maintained by a competent qualified installer who holds appropriate licences for Telecommunications and Security System cabling in accordance with local Regulations 2 Location The Control Module must be installed in a secure location near an AC Power outlet and Telephone line connection Install the unit where it will not be subject to temperature or humidity outside the specified range and will not come into contact with water other liquids high dust levels or chemical atmospheres Adequate ventilation must be provided around the cabinet 50mm min to ensure that heat from any other source does not cause the Control Module to operate at an unsafe temperature 3 Positioning Orientation of the cabinet MUST be as per the illustration below with the battery at the bottom Fit the Tamper switch into the hole provided in the Tamper switch bracket The Tamper switch bracket must be positioned in the slot pr
40. ovided and under the base of the cabinet before the cabinet is secured to the wall When wired to the TAMP input Tamper switch alarms if the cabinet is removed from the wall or the cover is opened 4 Mounting The cabinet must be secured to a flat solid vertical surface using appropriate fasteners through the 4 holes provided in the base and must be positioned to provide unhindered access for installation and maintenance The two mounting holes in the top of the cabinet are keyhole slots to assist with positioning When mounting onto flammable surfaces a fire protection backplate MUST BE INSTALLED 5 Power Plug Pack and cable color may vary outside Australia Strip 5mm of insulation from the ends of the 3 Plug pack cable conductors Terminate the 16VAC conductors into the AC Input connections and the Earth wire Green Yellow into BATT on the PCB CAUTION Do not connect the Plug pack to an AC outlet until all wiring is complete and checked 6 Battery Connect the pre assembled battery cable into the BATT and BATT connections on the PCB CAUTION Do not connect the Terminals to the Battery until all wiring is complete and checked 7 Cabling All cabling must enter the cabinet via the existing cutouts provided in the rear and sides Additional holes must not be cut in the cabinet Installation of Cables both inside the cabinet and external to the cabinet must conform to the appropriate Standards for Security and Tel
41. rminal Configuration Mode Initialize the LAN If a new Terminal is added to an existing system once the Terminal is configured and connected to the system LAN the LAN must be initialized by Removing and Re applying power to the Control Module Remember to disconnect the battery also when removing power Area Assignment Each Enhanced Terminal must be configured for Single Area Mode by selecting an Associated Area Address 561 564 with no area defined the Enhanced terminal will default to Area 1 Door Un lock time The Terminal auxiliary time for door unlock is set at Address 909 this is a global setting and applies to all Enhanced Terminals fitted a valid time is between 0 and 60 Default 5 seconds remember a low value allows little time to open the door p14 Rev 1 0 05 03 CONCEPT IQ Combined Installation Manual Enhanced RF LED Terminal 995500V2RF The Enhanced RF LED Terminal is a versatile operator interface for the Concept IQ system providing standard LED Terminal functions along with an interface for the Inner Range Wireless Keyfob Remote Control The Terminal provides status display of up to 16 Zone Inputs and 4 Areas along with indication of Power Fault Home Mode and Armed conditions Audible button press feedback is provided and the built in Beeper also provides indication of Alarms Entry Exit warnings Auto Arm warning User Operation OK and User Operation Unsuccessful While the system can be programmed via Upload
42. ther types of LAN Modules are Standard and Enhanced LED Terminals and RF Modules Recommended cable is 4 core or 6 core security cable 14 0 20 NOT twisted pair Twisted pair cable e g Category 5 may be used however DO NOT combine Clock amp Data on the same pair Do not apply power to cable until all connections are made and checked Maximum cabling distance from the Control Module to the furthest Module must not exceed 100 metres Maximum total LAN cabling in the system must not exceed 150 metres DO NOT connect the CLK amp DATA wires to the Control Module until all LAN Modules e g Terminals are Commissioned See Commissioning Instructions Disclaimer While every effort has been made to ensure the accuracy of this manual the manufacturer assumes no responsibility or liability for any errors or omissions Due to ongoing development this manual is subject to change without notice 2003 Inner Range Pty Ltd Part No 635500RF CONCEPT IQ Combined Installation Manual Rev 1 0 05 03 p15 INSTALLATION Connection diagrams provided on the next page Enhanced RF Terminal installation The Terminal must be installed on a flat vertical surface in an appropriate location Ensure that the display will be at or slightly below eye level for all Users Remove the rear mounting plate from the back of the Terminal Cut suitable holes in the mounting surface for cable entry and the fasteners The re
43. ts installed Programming Key connected to Port 0 LBHHH poorer IL Tie elleeleeeoc OPERATION uwulsssss Importing Data from the Programming Key This Mode allows the Installer to copy the programming contents of the Programming Key into the Control Module IMPORTANT NOTE The new data will override the existing contents of the Control Module memory Connect the Programming Key to Serial Port 0 on the Control Module Select the Import Data Mode Enter PIN C then vec then the Mode number 9 9 The Lamp on the Programming Key will flash slowly to indicate data is being copied The Terminal beeper will sound 3 short beeps if the operation was successful or 1 long beep if unsuccessful Export Data to the Programming Key This Mode allows the Installer to copy the programming contents of the Control Module into the Programming Key IMPORTANT NOTE The Control Module data will override the existing contents of the Programming Key Connect the Programming Key to Serial Port 0 on the Control Module Select the Export Data Mode Enter PIN JC C then r then the Mode number 9 The Lamp on the Programming Key will flash quickly to indicate data is being copied The Terminal beeper will sound 3 short beeps if the operation was successful or 1 long beep if unsuccessful Disclaimer While every effort has been made to ensure the accuracy of this manual the manufacturer
44. ust be connected in series with the button The Normally Closed Reed switch if used is connected between the Zone 2 Input and OV A 6k8 Resistor must be connected in series with the Reed switch When the Door Switch is NOT used and Door Alarm status see Commisioning 4 is not disabled a 6K8 EOL resistor must be fitted to Zone 2 if not fitted Door Forced alarms will occur and Lock Open times will be cancelled Lock Relay connection The Lock power must be switched via a Relay to provide isolation from the Terminal circuits e g 995085 1A DPDT Relay Board or 995083S 2x10A Relay Board The Relay control input is connected to and AUX1 on the Terminal The power to the lock must be wired from a separate lock power supply through the appropriate Relay contacts and must not make any connection to the Terminal wiring 2003 Inner Range Pty Ltd Part No 635500EN CONCEPT IQ Combined Installation Manual Rev 1 0 05 03 p13 Reet to ae a button Pr e e om Norma y Open Normally Closed Read Door Reed 000 Concept IQ j m Switch information EOL on Page 1 d Res LED Terminal ef 6k8 4 935500 Rev 1 Security Cable recommended 14 0 2 SONH31INI AV 13H 1A DPDT Relay d 4 Core v Board 995085 Fitreverse C Diode across Pwr to Lock Use NC 14 0 2 Lock coi
45. uts and or Auxiliary Outputs required Reconnect the power and the Battery to the Control Module then program the required Zones and Auxiliaries NOTES 1 CAUTION Shorting any of the pins on the Expansion Port connector whilst powered up can result in permanent damage to the Control Module and or the Expansion Card 2 To use the Zone Inputs on an Expander Card the EOL Resistor Type must be set to one of the Types 0 to 14 Types 15 and 16 Zone Doubled must not be selected Address 600 i e If Zone Doubling is used e g On Zones 1 to 8 on the Control Module the Zone Inputs on the Expansion Card CANNOT BE USED Only the Auxiliary Outputs can be used See next page for Zone Input amp Auxiliary Output wiring Control Module Location of Threaded plastic PCB standoff Concept IQ Expander _ 935504 Rev A il Inner Range VE ov Expansion Port 4 AX6 AX7 AXS AX10 ZN9 OV 2 10 ZN11 OV ZN12 ZN13 OV ZN14 ZN15 OV ZN 6 T9 EXT PORT 00000000 BT 5569606009 Location of Brass PCB standoffs 2003 Inner Range Pty Ltd Part No 635504 CONCEPT IQ Combined Installation Manual Rev1 0 05 03 p23 EXPANDER CARD WIRING DIAGRAMS Minimum Cable spec 14 0 2 T5 amp T6 VE and OV Detector Power connections 12V Supply for Detectors Total combined current sourced from DET and LAN on the Control Module and ve on the
46. will sound to indicate that the entry is accepted and the next Zone Lamp will now Fast flash for the next digit to be entered Enter the new PIN number w w J w 4 or 6 digits then press Three short beeps will sound to confirm the new PIN number has been programmed If the PIN is rejected one long beep will sound to indicate a problem Assign or Change the User Area or Areas Only required if you have a Multi Area System The lt A2 gt Lamp will flash to indicate the system is ready for the Area assignment entry The corresponding Zone Lamps 1 to 4 will indicate the Area s selected Press the Area number for each Area that is to be Assigned or Un assigned to this User When the required Areas have been Selected and or De selected press NOTE Each User programmed into the system can have an RF Remote OR Access Card assigned but not both If a person requires both of these items program two Users into the system for that person Set the options exactly the same for both Users and assign the RF Remote to one of them and the Access Card to the other User Programming can be found in the Programming manual or in the User s manual p22 Rev 1 0 05 03 CONCEPTIQ Combined Installation Manual Expansion Card 995503 995504 The Expansion Card connects directly to the Control Module Expansion Port and is available in 2 Versions 995503 Zone Expansion Card Provides 8 additional Zone Inputs and additional Dete

Installation Manual - JRW Security Services

Contents

Download Pdf Manuals

Related Search

Related Contents