STAINLESS STEEL AIR CURTAINS INSTALLATION MANUAL
Contents
1. SHER 3 4 1 Fix the air curtain as in the procedure for installing on the concrete wall y MOUNTING PLATE FIXING SCREW 4 TECHNICAL PARAMETER ee p FM 4009S L 1400m3 h 1000m3 h Air Volume m3 h PM 40125 L 1900mam 1500msm os FM 4018S L 2850m3 h 2250m3 h FM 4020S L 3255m3 h 2855m3 h Page 5 of 6 Noise Level dBA 1 metre Air Volume 1 s Air Velocity m s 3 3 4 Do the same as step A to install the main body 3 4 2 Then pipe as right Fig Instructs CEILING q Dimensions Saga Input power W Net V Weight Updated 26 June 2013 r oy LEVANTE 5 Wiring Diagram DOUBLE SPEED INFRARED CONTROLLED WIRING DIACRAM DOUBLE SPEED SWITCH WIRING DIACRAM 6 OPERATION 6 1 Turn on the power switch 6 2 Select the best speed High H Low L 6 3 According to using to adjust the grate to obtain the best effect 7 CAUTIONS a Use the unit at the rate voltage and frequency indication on the name plate b Disconnect power source before unit operation c Routing maintenance must be done every year d Never use petrol benzese thinner or any other such chemical for clearing the unit e Don t allow water or anything enter the motor f When power supply comes from socket the plug must accord with IEC335 1 When the power cord is connected with charging li2. ia LEVANTE Stainless Steel Air Curtain Supplier Www airc rcurtainsupplier com a Phone 613 97948182 info aircurtainsupplier com au STAINLESS STEEL AIR CURTAINS INSTALLATION MANUAL FM 4009S L Y FM 4010S L Y FM 4012S L Y FM 4015S L Y FM 4018S L Y FM 4020S L Y E my LEVANTE Thanks for purchasing this Air Curtain Please read these instructions carefully before use 1 IDENTIFICATION amp INSTALLATION DIMENSIONS A wom Ja Th OC DT EF ola 64 240 2 INSTALLATION CAUTION Must follow the following when installing stainless steel air curtain 2 1 Please install the unit in a sturdy place to 2 2 Please install the unit inside the room avoid shaking and ensure that it s secure Page 2 of 6 Updated 26 June 2013 E Ea LEVANTE 2 3 Don t install the unit too low no less than 2 3 meter from the ground 2 5 Don t allow gaps between the unit and the wall 3 INSTALLATION A Installing onto the concrete wall 3 1 1 Remove the mounting plate Unclamp the fixing screws on the back of main body to remove the mounting plate MaMa LLL LLL L INDOOR Z OUTDOOR 2 4 When the entrance is wider than the unit it is recommended to install two or more units in parallel I
3. n this case provide 20 40mm gaps between the units 20 40mm 2 6 Don t install the unit in a place where it is splashed by water exposed to excessive steam explosive or corrosive gas 3 1 2 Fix the bolts in the proper position Decide the position with the mounting plate and pour cement into the bolt holes Page 3 of 6 Updated 26 June 2013 a ia LEVANTE r MOUNTING PLATE 3 1 3 When the cement has set fit the mounting plate use the washer and nut according to the following WASHER SPRING WASHER Y K Hh A U ri NUT F ZA MOUNTING PLATE B Installing to a wooden wall 3 2 1 Fix the mounting plate in the proper position with tapping screws erie MOUNTING PLATE Remove the mounting plate from main Same as step3 1 1 MOUNTING PLAT SS he A FIXING SCREW Page 4 of 6 3 1 4 Install the main body Set the main body onto the upper end of the mounting plate and clamp it as shown 3 2 2 Same as step 3 of A WASHER f SPRING WASHER 7 NUT Updated 26 June 2013 LEVANTE 3 3 3 Set the mounting plate on the ceiling brackets and ensure safe amp fixing use the bolts attached to the ceiling brackets as Fig3 3 2 Using the ceiling brackets to hang from the ceiling the position of mounting plate can be adjusted in the limit of 100mm WASHER SPRING WA
4. ne directly all polarity switches that the contact gap is 3mm at least must be installed in the charging line Page 6 of 6 Updated 26 June 2013 E wey LEVANTE WARRANTY ALL CURTAINS 12 months parts only Distributed by CLEAN AIR SERVICES PTY LTD 1 147 GREENS ROAD DANDENONG SOUTH VICTORIA AUSTRALIA 3175 TEL 03 97948182 FAX 03 97935707 EMAIL info cleanairservices com au Page 7 of 6 Updated 26 June 2013
Download Pdf Manuals
Related Search