REGION4 CS52CD COPYSMART User Manual – V1.9 –
Contents
1. LCD will show the process of the erasing disc When erasing disc is finished the LCD will show the message as left Press ESC to go back Chapter 4 Trouble Shooting 1 No display on LCD or the unit does not operate when power on Please check the connection of power cable and the environment of power outlet is normal 2 LCD shows the Error message During operations like Copy Test Compare and Verify you may press ESC button to abort the operation An Error message will be shown on the LCD With some CD writers the abort will cause the duplicator to hang up and you have to re start the power to return to normal operation Failed reading may cause the error message shown on the LCD display Change the master CD to try again During operation if buffer under run or writing errors occur the LCD will show error message like Pass xx failed xx If there is no device connected and detected by duplicator during power on the duplicator will show error message on LCD before entering the main menu 3 CD ROM can not read disc and shows error message Check the format of master CD or master CD itself for damage Use the CD Writer to read the master if it works the CD ROM may be defective or not compatible with CD ROM 4 Buttons do not function May be still busy on task Button malfunction Faulty board 5 Copy completed but CD R disc is not readable executable Use compare to check Change to source drive to test 62. back MODEL FIRMWARE Press ENT button to see the device information and ESC to go back 3 11 14 System Info This function will show the system of information on the LCD 11 14 Setup System Info Press ENT button to enter the System Info and see the next information press ESC to exit CD Duplicator 1 1 ver 1 80L The LCD shows as below SST 39SF020 2001 11 16 3 11 15 Quick Erase This function will quick erase the data on the CD RW discs It will only take a short time to do it 11 15 Setup Quick Erase All data will be lost erase Yes Erasing disc 00 24 Quick Quick Erase OK 01 Fail 00 3 11 16 Full Erase Press ENT button to enter the Quick Erase and ESC to exit Use arrow buttons to change Yes or No setting then press ENT or press ESC to go back LCD will show the process of the erasing disc When erasing disc is finished the LCD will show the message as left Press ESC to go back This function will fully erase the data on the CD RW disc As it will completely erase all data it will take a few minutes complete 11 16 Setup Full Erase All data will be lost erase Yes Erasing disc 03 24 Full Full Erase OK 01 Fail 00 Press ENT button to enter the Full Erase and ESC to exit Use arrow buttons to change Yes or No setting then press ENT or press ESC to go back
3. change the setting and ESC to exit 3 11 2 Burn Speed This setting controls the maximum writing speed of CD writers Default setting is Auto which will use the highest writing speed of the writers Sometimes maximum writing speed will cause high failure rates that may be due to poor CD quality or unstable CD writing in high speed Under these circumstances please lower the writing speed under this setting to get higher successful rate in CD writing 11 02 Setup Burn Speed Press ENT to enter the setting and ESC to exit Burn Speed 24X Use arrow buttons to change the burning speed then press ENT Depending on the CDRW drive maximum speed support 3 11 3 Read Speed Sets the reading speed of the target source CD ROM 11 03 Setup Read Speed Press ENT to enter the setting and ESC to exit Read Speed 32X Use arrow buttons to change the reading speed then press ENT Depends on the CDROM maximum speed support 3 11 4 Auto Start Drive Use this setting to auto start copy or test when the blank discs are inserted into the CD RW drives Default setting is Off 11 04 Setup Auto Start Drive Press ENT button to enter Auto Start Drive and ESC to exit Auto Start Drive Off Use arrow buttons to change The number or Off setting then press ENT or press ESC to go back 3 11 5 Start up menu This setting selects one of the menu items which wi
4. Mode1 amp Mode2 CD ROM XA Mode2 form1 amp form2 CD DA Mixed Mode Video CD CD I Karaoke CD Photo CD Single amp Multi session CD Extra HFS CDBridge ISO9660 CD R and CD RW Writing mode Auto Detect DAO TAO Chapter 2 Installation and Operation Procedure Unpack the duplicator Check the entire unit to see if there is any mal function or damage found Make sure that the voltage setting is correct Connect power cable Switch on the CopySmart with the front power button 2 1 Key Functions and Operating Instructions ASARD 5 Esc LCD Display Panel Displays main functions and all messages Scroll up through menus or functions Scroll down through menus or functions ENT Executes the function which you select ESC Cancels the function which you select Power on the system The CopySmart will process a self test for a few seconds After the self test has completed the LCD will show CD Duplicator 1 1 ver 1 80L 1 Copy 2 2 Quick Start Place master disc in CD ROM Switch to Copy function by pressing arrow button Place a blank CD R or CDRW disc into the CD writer Press ENT button to start copying once the writer detects the CD discs front panel lights stop flashing When Copy is completed on the writer the passed CD disc will be ejected Default setting discs passed will be ejected This can be changed according to your need For continuous duplication place additional blank
5. REGION4 CS52CD COPYSMART Standalone CD Duplicators User Manual V1 9 Copyright 2003 Region4 Pty Ltd Chapter 1 Introduction 1 1 Overview Users who want to backup their CDs normally have go through many steps by turning on their computer launching the software setting up various parameters and tiding up their computer Sometimes it can take up to an hour to get only a few disc backups A standalone CopySmart will easily resolve this inconvenience CopySmart is a CD to CD R W standalone duplicator and does not need to connect to a computer It duplicates almost any format of disc with excellent accuracy With its professional mechanism design and multi function LCD panel CopySmart is easy for any end user to operate It is a perfect cost effective disc duplicator for audio data and video applications The simple four button control panel is designed to provide copy modes selection and copy operation 1 2 Features Standalone IDE to IDE CD Copy controller Self system diagnostics when power on Auto format detection User friendly interface with message rich LCD display Supports high speed CD RW writing mode Easy operation without software and training are required Firmware upgrade via CD ROM 1 3 Specifications Power requirement voltage 240V Environment Temperature Operating 0 oC to 70 oC Storage 20 oC to 85 oC Dimensions Length 285 mm Width 190 mm Height 165 mm CD Format CD ROM
6. SC to exit LCD will show the process of the prescan If the master of the disc can be read correctly the LCD will show OK message If the master disc cannot read correctly the LCD will show Fail message 3 7 Disc Info This function will show the total amount information on the master disc 7 Disc Info Total 02 Sessions Total 10 Tracks Total 74 00 Total 650 MB Session 01 Track 01 09 Track 01 AUDIO 03 54 3 8 Select Source Press ENT button to show the disc information or press ESC to exit The LCD will show the total sessions and tracks on the master disc Press ENT button again the LCD will show the total time and capacity on the master disc Press ENT button again and use the arrow button to select the session LCD will show what information is contained on the session Press ENT button again and use arrow button to select the track LCD will show what the information is contained on the track This function is provided to set the target source The source could be selected from CD ROM or CD R RW 8 Select Source Src CD ROM 01 IDEO Master CD ROM selected 3 9 Image Press ENT button to modify the select source function or press ESC to exit Use the arrow button to select the CD ROM or CD RW as the master source When the source is selected then press ENT button LCD will show the source information as on the le
7. The failure rate is high Lower the speed of CD Writer and try again Quality of bland disc is poor Check for latest firmware version Check the CD Writer maximum writing speed 7 Can not boot up or fail to upgrade firmware Contact your dealer to solve the problem Please note you may be charged for this A failed firmware upgrade might cause failed boot This can only be solved by returning the duplicator to the agent or factory directly 8 To cancel the duplicator working process Press ESC button for 2 seconds to cancel any Copy Test or Verify etc function while the job in working process Appendix 1 Directory Structure Copy Test Test amp Copy Verify Compare Prescan Disc Info Select Source Image OONOARWOWND 10 Edit Track For AUDIO disc only 10 01 CD to CD Edit 10 02 CD to HDD Edit 10 03 Play Audio Track 10 04 Close Session 11 Setup 12 Adv Setup 11 01 Language 11 02 Burn Speed 11 03 Read Speed 11 04 Auto Start Drive 11 05 Startup Menu 11 06 Auto Verify 11 07 Auto Compare 11 08 Auto Prescan 11 09 Eject Disc 11 10 Burn On The Fly 11 11 Burn Mode 11 12 Button Sound 11 13 Device Info 11 14 System Info 11 15 Quick Erase 11 16 Full Erase aa LCD Type1 English If no disc in CD RW list all supported speed else list speed supported by disc Maximum If ready CD RW number equals to this value auto start to copy or test Appendix 2 LCD M
8. ction of discs by the CD writer Three options are available Eject Good Only setting will only eject the passed discs automatically and leave the failed ones in the CD writers Eject All Disc means the CD writers will eject the CD discs no matter whether the copy operation is successful or failed Do Not Eject means all discs will remain in CD writers when the job is done and you will have to eject discs from the CD writers manually 11 09 Setup Eject Disc Press ENT button to enter Eject Disc and ESC to exit Eject Disc Eject Good Only Use arrow buttons to select Eject Good Only then press ENT or press ESC to go back Eject Disc Eject All Disc Use arrow buttons to select Eject All Disc then press ENT or press ESC to go back Eject Disc Do Not Eject Use arrow buttons to select Do Not Eject then press ENT or press ESC to go back 3 11 10 Burn on The Fly This setting controls the writing methods of the CD writers When the setting is On the data will direct copy from source drive to the target drive 11 10 Setup Burn On The Fly Press ENT button to enter Burn On The Fly and ESC to exit Burn On The Fly On Using arrow button to change On or Off setting then press ENT or press ESC to go back There is no HDD The CopySmart has no hard drive the LCD will show the message as left 3 11 11 Bu
9. discs into the CD writer and repeat the above procedures Failed disc s will remain in the CD writer Default setting Failed disc NOT ejected This can changed according to your need Pressing the ENT button will eject any failed CD from the writer or press each eject button on the CD writer to eject disc manually Chapter 3 Function 3 1 Copy When running the coping process the data will really burn into the blank CD R RW disc Before starting the coping process please make sure the master CD is put in the CD ROM drive before coping 1 Copy Place blank CD R CD RW disc into the CD writer When the writer detects the CD press ENT button duplicator will start copying Copying 24X 0 650 0MB 74 00 LCD will show the process of copying the disc 1 Copy OK 01 When copying is completed those discs passed will be ejected automatically and failed ones will remain in CD writer Put new CDs in the writer for additional copies NOTE The CopySmart is capable of CD RW writing Data stored in the CD RW disc will be quickly erased automatically before copying new data no special setting or procedure is required to erase the old data 3 2 Test This will simulate the CD R RW disc writing process When testing is completed the CD R RW disc will remain blank 2 Test Press ENT button to start the disc copy simulation or press ESC to exit Erasing disc For CD RW discs that contain data emulate will do q
10. essage List Normal LCD Message List Message Description Initialize SDRAM Detect Drives User Abort Analyzing Source Drive Not Ready Target Drive Not Ready Source Disc Not Ready Target Disc Not Ready Erasing disc Fail to get Drive Info Fail to get Src Disc Info Save new config Fail Load Default Config Src amp Tgt can t in the same channel Audio Disc Can t compare Identical Read disc error Cannot read TOC TOC not match Source Disc Empty Target overflow Target Disc Not Empty Press a Key to Eject Good Disc Press a Key to Eject Fail Disc CD RW does not Support the Func Hold ESC to exit All data will be lost erase Erase Finished No Eraseable Disc in CD RW Initialize the memory on the system Detect what drives are connected to the system Job was cancelled Analyzing the source disc Source drive is not ready to read Target drive is not ready to write Source disc in not ready for reading Target drive is not ready for writing System is erasing the data on the CD RW disc The drive is not correctly recognised Cannot read the information from CD ROM The new setting of configuration cannot be saved Loading the factory default setting When doing the compare operation the source and target can not in the same channel System is preparing the data and devices connecting for CD recording System is checking the target device wait for a while Audio disc compari
11. ft This function will show No HDD on the LCD 3 10 Edit Track This is a track selecting function that can combine tracks on different CD discs into one single CD disc For example you can make a collection of favorite songs from different music CDs and store them into one CD disc 10 Edit Track Press ENT button and arrow button to select or press ESC to exit 3 10 1 CD to CD Edit Select CD to CD Edit to choose the CD track on the CD ROM then you can copy directly from CD to CD 10 01 Edit Track CD to CD Edit Press ENT button to change setting ESC button to bring you to next setting Select Track 1 10 03 25 Follow the LCD to select the track you want to edit Select Track 1 10 03 25 Press ENT button to select track After the track is selected the will appear Pressing ENT again will cancel the track that you selected to edit Select Track End 1Trk03 25 Finally when the track selection is made use the arrow buttons to move to End End edit disc and burn Yes Press ENT button to finish the track selection Using the arrow buttons confirm to burn the track Copying 24X Edit 1 10 gt 1 1 LCD will show the process of CD Edit copying process Burn Complete OK 01 When track copying is finished the LCD will show the Burn Complete message Continue edit next Disc Yes System will ask if to continue edit Use the arrow butt
12. ll become the first menu item to show when turning on duplicator 11 05 Setup Startup Menu Press ENT button to enter Startup Menu and ESC to exit Startup Menu 1 Copy Use arrow buttons to select menu item setting for the first menu item to show 1 to 11 items then press ENT 3 11 6 Auto Verify This setting controls On and Off of auto verify for the target Default setting is Off 11 06 Setup Auto Verify Press ENT button to enter Auto Verify and ESC to exit Auto Verify Off Use arrow buttons to change On or Off setting then press ENT or press ESC to go back 3 11 7 Auto Compare This setting controls auto compare of the data between master and target discs after discs copy Default setting is Off 11 07 Setup Auto Compare Press ENT button to enter Auto Compare and ESC to exit Auto Compare Off Use arrow buttons to change On or Off setting then press ENT or press ESC to go back 3 11 8 Auto Prescan This setting controls the auto prescan of the master of the disc and tests the reading speed Default setting is OFF 11 08 Setup Auto Prescan Press ENT button to enter Auto Prescan and ESC to exit Auto Prescan Off Use arrow buttons to change On or Off setting then press ENT or press ESC to go back 3 11 9 Eject Disc This setting controls the eje
13. ng is not supported Confirmation after comparing that the contents of CD is the same During the comparing the disc has a read error CD s TOC data can not read After comparing the source and target device s TOC do not match The source CD is blank without data The target blanks do not have enough space to record the source The target disc is not empty to record Press any key to eject the good disc after the recording process Press any key to eject the fail disc after the recording process CD RW drive does not support this function Press ESC for a seconds to terminate the testing All data on the CD disc will be lost Confirm to erase the CD RW disc CD RW disc has been erased The CD discs in the CD RW drive is not erasable disc Audio Edit Messages Message Description Lost selected Tracks End edit disc and burn Continue edit next Disc Target Overflow Re Select Close all disc s session Can t edit HDD No AUDIO track in this disc Insert next disc Sessions were closed already Burn or Move to partition Tgt overflow del last trk Ins empty disc Continue Abort the tracks selected and delete it Finish the music disc edit and start to record the CD Asking to continue editing next music disc or not The CD disc space is not enough to record the selected track please re select another Closing the disc s session and will not allow to record any further data The hard drive can n
14. on to enter the play audio function ESC button to bring you back one menu Use arrow buttons to select which track you are going to play LCD will show the process of Audio Playback 3 10 4 Close Session Selecting Close Session will make the disc close and you cannot write any additional data to it This function is required to allow the disc to be read on normal player 10 04 Edit Track Close Session Press ENT button to close session ESC button to bring you to next setting Close all disc s session Yes System will ask a confirmation to close the disc s session After this step the disc cannot have additional data written to it Closing Session Please wait LCD will show the progress of the disc closing Closing Complete OK 1 Fail 0 When closing session is finished the LCD will show the number of discs OK and Fail message 3 11 Setup This function contains a list of options that allow user to change the original default settings As there are different settings under the setup function to control the duplicator s operation we suggest using the original default settings for optimal operation 11 Setup Press ENT button to enter the Setup function 3 11 1 Language optional Use this option to set which language is shown on the LCD There are English Traditional Chinese Simplified Chinese and Japanese languages 11 01 Setup Language Press ENT to
15. ons to make Yes or No selection Insert next disc If Yes is selected the source disc will be ejected Please inset another audio disc to edit Select Track 2 10 04 25 Follow the step to select the track that you want to edit Then press ENT button to add it on the disc Select Track End 2Trk07 50 End edit disc and burn Yes Copying 24X Edit 1 10 gt 2 2 Burn Complete OK 01 Continue edit next Disc No Close all disc s session Yes Closing Session Please wait 3 10 3 Play Audio Track Finally when the track of selection is made Please use arrow button to move to the End menu Press ENT button to finish the disc editing using arrow buttons to make Yes or No selection LCD will show the process of CD Edit copying process When Copy is finished the LCD will show the Burn Complete message System will ask if you wish to continue editing Use arrow buttons to make the No selection then press ENT button The system will ask to close the disc session Using arrow buttons make Yes or No selection LCD will show the process of closing the session Select Play Audio will use the CopySmart as a music player You can plug speakers into the audio out from the front panel of the CD ROM drive 10 03 Edit Track Play Audio Track Select Track 1 10 03 25 Playing Track 1 00 00 03 25 Press ENT butt
16. ot edit as a source audio CD The source CD disc can not find a audio track Asking to insert the next audio disc The disc session has already been closed Confirmation of direct burning to CD disc or move the data to the partition The CD disc space is not enough to record the selected track asking to delete the last track Asking to insert an empty disc and continue the process
17. rn Mode This setting controls the writing methods the CD RW disc including Disc At Once DAO or Track At Once TAO Default setting is DAO Some CD writers may support different writing methods If the method selected is not supported the duplicator will automatically switch to the other one 11 11 Setup Burn Mode Press ENT button to enter Burn Mode and ESC to exit Burn Mode DAO Use arrow buttons to change TAO or DAO mode setting then press ENT or press ESC to go back 3 11 12 Button Sound This setting controls button sounds Default setting is On Press ENT button to change and ESC to exit 11 12 Setup Button Sound Press ENT button to enter Button Sound and ESC to exit Button Sound On Use arrow buttons to change On or Off setting then press ENT or press ESC to go back 3 11 13 Device Info This function will show what devices are connected Each devices brand and type of information will be shown on LCD 11 13 Setup Device Info Press ENT button to enter the device information and ESC to exit 00 IDEO Master CD ROM BRAND Use arrows button to select the device or press ESC to go back MODEL FIRMWARE Press ENT button to see the device information and ESC to go BACK 01 IDE1 Master CD RW BRAND Using arrow button to select another device or press ESC to go
18. to exit Verify 24X 0 650 0MB 74 00 LCD will show the progress of the Verify process 4 Verify OK 01 When the process is finished the LCD will show the Verify result 3 5 Compare The data on master and target disc will be compared to each other This will confirm an accurate copy has been made 5 Compare Press ENT button to run the disc compare or press ESC to exit Compare 24X 0 650 0MB 74 00 LCD will show the progress of Compare process Compare OK 1 Fail O Diff 0 Src 01 CD ROM Total 650 0MB Src 02 CD RW Identical Compare OK 2 Fail 1 Diff 0 Src 01 CD ROM Total 0 Bytes Src 02 CD RW TOC not match 3 6 Prescan When the process is finished the LCD will show the result of the Compare process The CD disc will be ejected by CD writer Press ENT button to see the results of Compare If the compare result is identical the LCD will show the message as left If the compare result has failed the message will show the number of discs failed amp succeeded Press ENT button to see the detail of Compare information If the compare result is failed the LCD will show the reason of fail message as left This function will scan the master disc to confirm if can read correctly and test the reading speed 6 Prescan Scaning 24X 0 650 0MB 74 00 PreScan OK PreScan Fail Press ENT button to prescan the disc or press E
19. uick erase of all old data before emulation Thus never do emulate on CD RW discs that contain important data Testing 24X 0 650 0MB 74 00 LCD will show the process of testing the discs 2 1 est OK 01 When the process is finished the LCD will show the message of the Test result Termination during Test will not affect the CD R disc and it will remain blank But please note that CD RW discs containing data will be destroyed and cannot be retrieved again Some CD writers may not support sudden termination during operation The duplicator may hang up and you can only reset those writers by re starting the power 3 3 Test amp Copy 3 Test amp Copy Press ENT button to do the disc testing then really write the data on the disc or press ESC to exit Testing 24X 0 650 0MB 74 00 Before starting the copying process the writer will simulate the data writing process Copying 24X 0 650 0MB 74 00 When testing process is completed duplicator will start writing data onto the CD R RW disc The CD R RW disc will contain data 3 Test amp Copy OK 01 When the process is finished the LCD will show the result of the Test amp Copy 3 4 Verify This will verify if the target disc can be read correctly in the CD ROM drive after copying of the disc Discs in the CD writer and CD ROM drive can be verified together simultaneously 4 Verify Press ENT button to start the disc verify or press ESC
Download Pdf Manuals
Related Search