User Manual for FIT 188 Alcohol Computer Watch
Contents
1. Specification subject to change without notice Made in PRC China Page 2 188 06Y01568 user manual FIT 188 R00 16 Nov 20062. amp to alter the selected digits 8 Press to shift the selected digit 9 In AL mode press UP to en disable the chime and press to en disable the clock alarm 10 In AL mode press key for 2 seconds to enter into alarm setting mode The selected digits for adjusting will flash 11 Press UP amp DOWN to alter the selected digits 12 Press START to shift the selected digit Alcohol testing a ae 1 To begin wash your mouth with water before using the unit Abstain from smoking or drinking for at least 20 minutes 2 Insert the provided blowing tube completely into the transparent gas inlet located aside of the watch 3 In RTC mode press the Key for 0 5 seconds to activate an approximate 20 30 seconds sensor warm up process PH flashes and then followed by 15 second count down or 30 second for long time un used machine READY flashes with beep tone when count down to zero and ready to start 4 Blow continuously through the blowing tube for approximately 6 seconds When auto detect your breath sample successfully and BLOW will be shown on the display when detect the breath sampling Err shows if less than 6 seconds continuous blow Stop blowing when you hear a beep tone and the reading shows on the display If BLOW flashes while blowing it means there is residue inside the chamber Please clear the residue and test again i A measurement of less than 0 15 BAC 0 075mg l or 0 015 B
3. AC will show LO and no breath sample detected will also show LO li A measurement between 0 15 BAC 0 075mq I or 0 015 BAC amp 1 50 0BAC 0 75mq I or 0 15 BAC will show its digital reading iii A measurement above 1 50 BAC 0 75mg l or 0 15 BAC HI amp NO DRIVING will flash on the display 5 Press to convert the alcohol unit but the default unit will resume for another alcohol test Alert Signals FIT 188 is designed to alert user as following 1 Low Level For measurement below 0 15 BAC 0 075mq I or 0 015 BAC LO will be shown on display with GREEN backlight 2 Safety Level For measurements between Low Level gt 0 15 BAC 0 075mqg I or 0 015 BAC and Pre alert Level Warning Level the alcohol concentration level shows on the display with GREEN backlight Page 1 188 06 Y01568 user manual FIT 188 RO0 16 Nov 2006 User Manual for FIT 188 Alcohol Computer Watch 3 Pre alert Level For measurements within 0 15 BAC 0 075mq l or 0 015 BAC below the alert point The analyzer beeps together with NO DRIVING amp HI flashes alternatively for 4 times and RED backlight flash as well The LCD will keep the RED backlight for 15 seconds DON T DRIVE You are very close to the alert level or you have reached the alert level if take tolerance of the unit into account 4 Alert Level For measurements equal to or above the alert concentration level the analyzer beeps t
4. User Manual for FIT 188 Alcohol Computer Watch Thanks for purchasing our FIT188 Breath Analyzer a hand held Digital Alco Watch with temperature and Calendar Watch FIT188 gives you a digital indication of your breath alcohol content and thus your possible concentration of intoxication Operation instructions Li General To 1 Use the provided charger cable and car charger optional to charge up the mo battery for at least 12 hours when it is the first time of use Make sure the AT ve and ve sign on both cable and the watch bottom are matched The pa battery charging animation gt will move forward and backing when Ni aia l the cable is connected correctly aono y 2 If no battery the battery indicator will flash and please charge up the battery Ss rd immediately Te Time amp unit setting 1 Press MODE key for 0 5 seconds to turn on the back light Loco 2 BATTERY INDICATOR 2 Press UP to change the temperature unit 4 oe Oe 3 Press DOWN to read the maximum and minimum temperature MODE Gap were vs ie E memories AT og 4 Press DOWN for two second to reset the max and min temperature memories d 5 When back light is on press again to toggle Real Time clock mode U I ra RTC amp Alarm mode AL FRAY 6 In RTC mode press MODE key for 2 seconds and enter into time a a setting mode The selected digits for adjusting will flash 7 Press UP
5. eep sound is heard User can press Key once to stop the alarm sound of Err 4 When the product is unused please store in a dry environment 5 When low battery inductor flashes the reading is not valid please recharge the battery immediately 6 If the difference between two successive reading gt 0 1 BAC 0 05mg l or 0 01 BAC user should test again Product Specifications 1 Alcohol Range 0 15 1 50 BAC or 0 075 0 75 mg l 0 015 0 150 BAC 2 Measuring Temperature Range 20C to 7 70 C 2 Power Input 3 6V rechargeable battery Build in 3 Operating Temp 10C to40 C 4 Storage Temp 10C to60 C 3 Display Digital display with bi color backlighting 4 Real time clock power save mode 2 minutes after any key in 5 Breath sampling About 6 seconds continuous breath sample 6 Recycle time 20 seconds 7 Weight 135g 8 Alert level calibrated L10 2 BAC LI0 3 BAC L10 5 BAC L10 8 BAC L10 15mg l 10 25mg l L10 05 BAC LI0 08 BAC 9 Agency Approval CE 10 Accessories 3 pcs blowing tubes 1 pc Auto cleaning cap The FIT 188 Digital Alcohol Computer should be used as a general guide to the level of alcohol in your body Many factors e g environment gas residue smoke amp various smells in human mouth etc may affect the BAC level so the Readings are For Reference Only Neither the reseller nor manufacturer accept any liability arising from the use of this unit DO NOT drink before you drive
6. ogether with NO DRIVING amp HI flashes alternatively for 15 seconds and RED backlight flash as well The LCD will keep the RED backlight for 15 seconds The alcohol concentration level displays and NO DRIVING will then remain on the LCD with RED color backlight If reading greater than 1 50 BAC 0 75mq I or 0 15 BAC HI amp NO DRIVING will remain on the LCD with RED backlight Press MODE key can stop the alert sound YOU ARE PROHIBITED TO DRIVE since you already exceed the alert level Note 1 To ensure high precision readings user should perform the auto cleaning if unused for a long period especially for the first time of using User can start the auto cleaning process Put a few drops of alcohol solvent lt 1 inside the provided cleaning cap accessory Place the cap onto the gas outlet and then press ST key to activate the sensor pre heating process The machine will perform a formal alcohol testing as describe in xx x After the cleaning process remove the cleaning cap and let the machine rest for few minute and let all residues off the chamber and Make sure no alcohol residues left by blowing fresh air into the gas inlet before formal testing 2 After any 5 consecutive tests allow the device to rest for 2 minutes 3 An Err flashes on the display for 5 seconds for the following improper operations When user does not blow continuously for at least 6 seconds during blowing until a b
Download Pdf Manuals
Related Search