User Manual for FiT208-S Digital Alcohol Analyzer
Contents
1. 2 Please notice that pressing the MODE key at any time can easily terminate the auto cleaning process 3 To achieve an accurate reading user should ensure there is no alcohol residue inside the chamber before starting a new alcohol test Users can pre check the tester until the Lo indication is shown on the display This may be achieved by pressing key once Holding the key and blow fresh air into gas inlet for about few seconds Alternatively shaking the unit forwards and backwards several times will allow any alcohol residue to leave before starting a new alcohol test 4 After any 5 consecutive tests allow the device to rest for 2 minutes 5 An Err flashes on the display for 5 seconds for the following improper operations i When user does not hold the key for at least 6 seconds during blowing until a beep sound is heard ll When user fails to start the test within 10 seconds after READY turns on and blow flashes User can press Key once to stop the alarm sound of Err Storage and handling 6 When the product is left unused please store in a dry environment 7 When low battery inductor flashes the reading is not valid please replace the batteries immediately 8 This is an instrument for breath alcohol concentration user should avoid the tester from high impacted or drop Please ask for the recalibration from your nearby service centre if such kind of abnormal impact occurred 9 Recalibration Accordi2. UNIT key once to convert the alcohol unit in DAC mode between BAC BAC mg l iii Press amp REV key once to scroll forward the 5 memory readings and then the average reading iv Hold amp REV key for 2 seconds to clear the memory readings in alcohol mode Real time Clock setting i When in Real time Clock mode hold Y SET key for 2 second to enter into time setting in RTC mode i Press 4 ADV key once to advance the selected digit in RTC setting mode ll Press W SET key once to decrease the selected digit in real time setting mode lil Press ST key once to shift the select digit in real time setting mode Note 1 To ensure high precision readings user should perform the auto cleaning if unused for a long period especially for the first time of using User can start the auto cleaning process by holding amp 4 keys together for 2 seconds or by removing the batteries and power up again Put a few drops of alcohol solvent lt 2 inside the provided cleaning cap accessory Place the cap onto the gas outlet when you see the animation of CAP u gt CAP n for 10 seconds Then take off the cap when Auto amp Clr flashes and leave the Fil208 S perform the 3 minutes auto cleaning The analyzer will then return to normal Alcohol mode automatically when the cleaning process finishes Make sure no alcohol residues left by blowing fresh air into the gas inlet before formal testing
3. tone and the reading shows on the display ie A measurement of less than 0 15 BAC will show LO li A measurement between 0 15 amp 1 5 0 BAC will show its digital reading iii A measurement above 1 5 BAC HI amp NO DRIVING will flash on the display iv re amp test flash alternative on the display if the tester left unused for 10 minutes repeat setp 6 v Air amp Clr will flash for 10 second and then re amp test BATTERY INDICATOR will flash alternative on the display for 2 minutes if user continuously test for 7 times After 2 minutes waiting the c0 a ook Yr eS NO DRVING SYMBOL machine will resume to normal User is requested to clean a INDICATOR FOR READY residue inside the chamber while Air amp Clr flashing ST KEY f _ _ _ _ j i a YY aA KEY REV ADV Y KEY SET UNIT Wies 4 Result 8 Should repeat step 4 7 four times After 5 test samplings press A REV key once to scroll backward the last five pre test memory A readings Press 4 REV key once more and get the final average reading of your five test samplings AVG amp the 5 memoery bars flash alternatively 9 Ifthe difference between two successive reading gt 0 1 BAC user should test again Alert Signals FiT208 S is designed to alert user as following For measurement below 0 15 BAC LO
4. will be shown on display with GREEN backlight Safety Level For measurements between Low Level gt 0 15 BAC and Pre alert Level Warning Level the alcohol concentration level shows on the display with GREEN backlight Pre alert Level For measurements within 0 2 BAC below the alert point The analyzer beeps together with NO DRIVING amp HI flashes alternatively for 3 times GREEN amp ORANGE backlight exchanges alternatively as well The LCD will keep the red backlight DON T DRIVE You are very close to the alert level or you have reached the alert level if take tolerance of the unit into account Alert Level For measurements equal to or above the alert concentration level the analyzer beeps together with NO DRIVING amp HI flashes alternatively for 15 seconds ORANGE amp RED backlight exchanges alternatively The alcohol concentration level displays and NO DRIVING will then remain on the LCD with red color backlight If reading greater than 1 5 BAC NO DRIVING amp HI will remain on the LCD Press MODE key can stop the alert sound YOU ARE PROHIBITED TO DRIVE since you already exceed the alert level Page 1 218 06Y01365 US r manual FIT_208 S R41 0 2006 09 02 User Manual for FiT208 S Digital Alcohol Analyzer Enhanced feature instructions Unit conversion and memory recall i Hold Key for 0 5 seconds to toggle Real Time clock RTC Alcohol mode DAC ll Press W
5. User Manual for FiT208 S Digital Alcohol Analyzer Thanks for purchasing our Fil208 S Breath Analyzer a hand held Digital Alcohol Computer FiT208 S gives you a digital indication of your breath alcohol content and thus your possible concentration of intoxication To achieve the high accuracy user should follow the step 8 and the final reading shows on the display together with AVG amp the 5 memoery bars flash alternatively Operation instructions Install 3pcs AAA 1 5V Alkaline battery into the battery compartment auto cleaning will automatically activate according to the CAUTION manual amp refer to page 2 note 1 amp 2 2 To begin wash your mouth with water before using the unit Abstain from smoking for 10 minutes or drinking for at least 20 minutes Press MODE key for 0 5 seconds to toggle Real Time clock mode RTC amp Alcohol mode DAC Make sure no alcohol residue inside the chamber Page2 note 3 Insert the provided blowing tube or drinking straw into the gas inlet located on top of the LCD screen Press the Key for 0 5seconds to activate an approximate 20 seconds sensor warm up process PH flashes for about 4 seconds and then followed by 15 second count down READY displays together with blow flashes with beep tone when count down to zero and ready to start 7 Hold the Key while blowing continuously through the blowing tube for approximately 6 seconds Stop blowing when you hear a beep
6. ng to the international standard e g DIN31051 all measurement instrument should be recalibrated every 6 months Product Specifications 1 Range 0 15 1 5 BAC 2 Power Input 3pcs AAA 1 5V Alkaline batteries 3 Display Graphic amp Digital display with tri color backlighting 4 Real time clock power save mode 2 minutes after any key in 5 Breath sampling About 6 seconds continuous breath sample 6 Recycle time 20 seconds 7 Dimensions 88 X 47 X 24 mm approx 8 Weight 50 without batteries 9 Alert level calibrated 10 2 10 3 10 5 10 8 BAC 10 Agency Approval CE 11 Accessories 3 pcs blowing tubes 1 pc Auto cleaning cap The FIT 218 Digital Alcohol Analyzer should be used as a general guide to the level of alcohol in your body Many factors e g environment gas residue smoke amp various smell in human mouth etc may affect the BAC level so the Readings are For Reference Only Neither the reseller nor manufacturer accept any liability arising from the use of this unit DO NOT drink before you drive Specification subject to change without notice Made in China Page 2 218 06Y01365 US r manual FIT_208 S R41 0 2006 09 02
Download Pdf Manuals
Related Search