Home

LP Morgan Flipper User Manual

1. Dimension Name Std Flipper Lrg Flipper A Overall Length 575 675 C Overall Width 670 770 K Operating Height 350 400 IL Cutout Length 528 628 M Front amp Back Offset 23 5 23 5 N Cutout Width 478 578 P Left Offset 26 26 O Right Offset 166 166 Q Widthways Hole Spacing 500 600 R Lengthways Hole Spacing 558 658 S Hole Offset 8 8 T Right Hole Offset 162 162 LP Morgan Installation Instructions 11 LP Morgan Flipper Manual Electrical Installation Do Not under any circumstances connect 240 VAC to any of these A terminals The Flipper is supplied with a 12V control unit that can be operated by either close contacts or the supplied wall switch You do not need to be a qualified electrician to wire the Flipper as all circuiting is 12V however Herma will not accept responsibility for damage incurred by faulty or incorrect wiring The motor limit switches and power supply are supplied pre wired into the control box If you need to disconnect them use the following wiring diagram very carefully You could damage your Flipper permanently if you wire it incorrectly Control Unit Wall Switch and Architrave Mount 12 LP Morgan Installation Instructions LP Morgan Flipper Manual Wiring Diagram We supply these units pre programmed to operate via a maintained SPST switch a single throw relay The supplied switch should be connected to the Up and Common
2. terminals ONLY Should you wish to use a different sort of switching method eg SPDT you can easily program the device to do so However you will need a receiver eye and special programming remote available as our Installer s Kit LPM43INSKIT 12V Negative Motor Blue Switch Down Not used in standard configuration Motor Brown Switch Up Use a small flat screwdriver to prise open the motor and mains terminals Stall Sensing These control units have an in built stall sensor which is a necessary feature if you are installing a Flipper into a tabletop To activate the stall feature you need to purchase a programmer s kit LPM43INSKIT has included detailed instructions on setting a calibrating the current threshold Contact Herma if you want further information on stall settings LP Morgan Installation Instructions 13 LP Morgan Flipper Manual Projector Installation The Flipper uses the LP Morgan Skyhook projector mount system Step 1 The parts kit contains e 4x long Skyhook arms e 2x short Skyhook arms 4xM4 4xM5 amp 4xM6 mounting bolts e 4x springs Determine which size mounting bolts suit your projector and set others aside They are no longer required Step 2 If your projector has only 3 mounting holes remove one of the adjustable arms Undo the M8 Nyloc nut remove an arm and replace the nut Step 3 Before connecting the Skyhook spread out the
3. arms so each end is over one of the mounting holes If you feel it necessary this is an appropriate time to remove 1 or 2 of the short arms and replace with the supplied optional longer arms Front of projector 14 LP Morgan Installation Instructions LP Morgan Flipper Manual Step 4 Connect Skyhook to Projector Fit the springs between the arms and the projector and tighten the mounting bolts so that the projector is parallel to the triangular plate Step 5 Move the position of the triangular plate over the centre of the projector with the edge with the 2 holes towards the front Step 6 Tighten the mounting bolts The projector and Skyhook system is ready to be inserted into the Flipper LP Morgan Installation Instructions 15 LP Morgan Flipper Manual Flipper Skyhook unit First ensure that the Flipper is operating correctly and that the projector cables are properly secured Open the Flipper and bolt the triangular projector plate to the underside of the Flipper using the supplied M6 bolts and springs M6 Bolt and Washer Detail M6 bolts and Spring These bolts will also give you Yaw and Tilt adjustment to align your image on the screen while the centre M8 bolt provides Pan adjustment The springs will ensure that the projector is held still during motion Do not install the projector plate without springs Extra Adjustment You can fine tune the open and closed
4. lpmorgan com au lp morgan October 2011 Version 2 2
5. positions of the Flipper by adjusting the angle of the two limit arms on each side of the pivot frame see page 5 for part names These arms hit the limit switches in the closed and open positions 16 LP Morgan Installation Instructions LP Morgan Flipper Manual Cable Management Because every projector has a different point of access for its mounting points and cable the Flipper provides an exit opening on the side of the pivot frame for the projector cables There are two holes near this cutout that you may use to tie off the cables so that they are firmly secured Ensure that you leave enough slack for the cables so that the cable will not interfere with the motion of the unit Cable management LP Morgan Installation Instructions 17 LP Morgan Flipper Manual Mulitiflip The multiflip bracket is an accessory that allow you to install the Flipper into an angled ceiling or even a wall You do not need to use the multilfip if installing into a horizontal ceiling or tabletop Step 1 Remove one of the limit arms the one that sets the open position and attach it to the multiflio bracket as shown using the supplied M6 x 10 Bolt Step 2 Attach the mutliflio bracket to the Flipper as shown using another of the M6 x 10 Bolts Position of Adjuster Arm determines stopping angle of Flipper 18 LP Morgan Installation Instructions LP Morgan Flipper Manual Step 3 A
6. LP Morgan Flipper User Manual lomorgan www lpmorgan com au LP Morgan Flipper Manual Table of contents To the owner Unpacking Part names Dimensions Mechanical installation Ceiling opening Ceiling space Electrical installation Wiring diagram ATTENTION O 1 N on A Co 10 11 12 13 Projector installation 14 15 Flipper Skyhook unit 16 Cable management 17 Multiflip 18 19 Dust cover fitting 20 Accessories 21 Maintenance and 22 Troubleshooting Warranty Information 23 Please read all of these instructions before you operate your Flipper for the first time Save these instructions for further reference A Never operate the Flipper while the projector is still powered Information in this document is subject to change without notice Herma Technologies All rights reserved This document is protected against unauthorised copying electronic or otherwise Trademarks used in this text Herma the Herma Logo Galleria LP Morgan and LP Morgan logo are registered trademarks of Herma Technologies Other trademarks and trade names used in this document remain the property of the relevant owners October 2011 Version 2 2 2 LP Morgan Installation Instructions LP Morgan Flipper Manual To the owner Congratulations on purchasing an LP Morgan Flipper This innovative projector mounting system is a novel and secure way to mount your projector out of sight when not in use giving y
7. P Morgan Flipper Manual Mechanical Installation The Flipper may be installed through its own hole if required The first crucial step like any projector installation is to determine where to put the Flipper in the ceiling The Flipper should be installed so that the projector lens is centered horizontally to the screen and the distance from the screen depends on the projector s throw distance Work out the maximum and minimum throw distances for the projector and place the Flipper somewhere in between It is better for the projector to be closer to the screen but don t place it at an extreme leave yourself some room to adjust the zoom in either direction Screen Projector centre Screen centre Lens centre Throw Distance Note When aligning the Flipper make sure that the projector lens is centred on the screen which is not necessarily the projector centre 8 LP Morgan Installation Instructions LP Morgan Flipper Manual Ceiling opening The Flipper was designed by an installer with the installer in mind The face panel that is supplied is 18mm undercoated MDF and is easily removed via six SCrews We recommend that you remove and paint this panel before fixing the Flipper in the ceiling In the case of a non plasterboard ceiling you may choose to fabricate your own ceiling panel eg from the same timber material as the ceiling itself to match The Ceiling trim we supply will leave a 2mm c
8. djust the position of the Limit Arm to give you the desired stopping angle arm engages limit switches Flipper in Angled Ceiling Projector is Horizontal when in use LP Morgan Installation Instructions 19 LP Morgan Flipper Manual Dust Cover Fitting We supply a folded cardboard box as a dust cover for the Flipper Cardboard is much more environmentally friendly than plastic cheaper and is easily modified to suit your specific installation Note You may need to cut the dust cover to fit around over bearers in the ceiling Space for the Motor Double Sided Adhesive Pad 20 LP Morgan Installation Instructions LP Morgan Flipper Manual Accessories The following accessories are also available from LP Morgan Contact your local retailer for pricing information Triggering From Projector HER20HD12V 12 volt trigger unit for projectors with a 12 volt trigger output e Often used also with LPM43SCR12V Screen 12V Trigger LPM48HDSCRTRIG Trigger Unit for Projectors without a 12 Volt Trigger e Uses current sensing to detect when the projector is on e Triggers a screen as well e Includes an IR repeater kit Infra Red Remote Control HER20HDIRKIT Infra Red remote control and receiver Radio Frequency Remote Control HER20HDREKIT Radio Frequency remote control and receiver RS232 Integration LPM43MULTI RS232 Interface for both Projec
9. e diagram on page 10 and take careful note of the motor and projector orientation The unit may be turning the wrong way if this is so it will damage the microswitches as it turns Contact Herma for advice The Face panel is not squared centred in the trim Loosen the 6 screws but don t undo and you will be able to adjust the position of the face panel slightly by about 2mm since the holes the screws go through are a 2mm larger than the screws 22 LP Morgan Installation Instructions LP Morgan Flipper Manual Warranty Information Keep your original receipt for warranty Please fill out the online warranty form in order to qualify for the manufacturer s warranty http www pmorgan com au owners html The warranty covers defects in workmanship and materials provided this product has been installed in a normal environment and maintained according to the written instructions Herma warrants the product against loss of usefulness discolouration or deterioration of optical quality within the warranty period as a result of manufacturing or material defects This warranty applies only within Australia Please return your goods to the place of purchase for all warranty claims Conditions Any equipment replaced pursuant to the terms of this warranty shall be retained by Herma All costs related to de installation and re installation of the product covered by this warranty are not the responsibility of Herma Technologi
10. es Herma will not be responsible for any consequential damages during or following installation procedures Herma is not responsible for any freight costs relating to repair or replacement Equipment must be returned to Herma in suitable packing to prevent damage in transit Herma will not accept any responsibility for damage to the equipment caused by inadequate or unsuitable packing or for any damage howsoever caused whilst the goods are in transit Herma Technologies shall not be liable for any injury loss or damage direct or consequential arising out of the use of misuse of or inability to use the equipment This Warranty does not cover any product which has been subjected to misuse abuse neglect accidental or intentional damage improper voltage or any alteration which affects the reliability or performance of the equipment not attributable to faulty manufacture parts or labour and without limiting the generality of the foregoing This Warranty does not cover any product where usage adaptation or installation are not in accordance with our written installation and operating instructions Warranty Periods Two years from date of purchase LP Morgan Installation Instructions 23 For more information on our range of products please visit www pmorgan com au or contact your local LP Morgan Retailer Factory 4a 6 Albert Street Preston Vic 3072 Phone 61 3 9480 6233 Fax 61 3 9480 6533 Email info herma com au www
11. learance on all sides of this face panel If you choose not to use this ceiling trim you should be aware that you will need to allow more clearance at the front and back of the panel because the trajectory traced by the ceiling panel is actually wider than the ceiling trim For a Standard Flipper Length Width Face Panel 500 450 Cutout required if NOT using the supplied trim 508 454 Cutout required if using the supplied trim 528 478 For a Large Flipper Length Width Face Panel 600 550 Cutout required if NOT using the supplied trim 608 554 Cutout required if using the supplied trim 628 578 LP Morgan Installation Instructions 9 LP Morgan Flipper Manual Ceiling Space The following diagrams show the position of the ceiling Cutout in relation to the Flipper frame the space required above the ceiling and the mounting hole positions The Flipper has been designed to be compatible with just about any installation situation You should be able to adapt the Flipper to suit your specific installation requirements The Flipper frame is designed to sit 12 5mm above the ceiling that is it virtually rests on the plaster Where possible install the Flipper in such a way that you can micro adjust the height so you can get it exactly flush with the ceiling eg suspended from threaded rod 10 LP Morgan Installation Instructions LP Morgan Flipper Manual
12. ou maximum enjoyment and a truly cinematic experience Since the Flipper was first released in 2004 we have added some new features that makes the Flipper even more versatile e Multiflip for installation at any angle even in a wall e Stall Sensing for installation in a tabletop bench Current sensor detects an obstruction and will stop the unit for added safety Please take a moment to review this manual as it will ensure you many years of trouble free service from your new Flipper On Safety Check that the operating voltage of your unit is identical with the voltage of your local power supply If voltage adaptation is required consult with a qualified electrician Should liquid or solid objects fall into the unit unplug and have it checked by qualified personnel before operating it further To disconnect the cord pull it out by the plug Never pull the cord itself The power supply should be near the unit and easily accessible Do not place your hand or other objects near the trapdoor during operation The Skyhook Projector Mount must be used for installation with the Flipper On Cleaning To keep the unit looking new and clean a dust cover is supplied If cleaning is necessary use a soft cloth and mild detergent solution Never use strong solvents such as thinners benzene or abrasive cleaners LP Morgan Installation Instructions 3 LP Morgan Flipper Manual Unpacking the Flipper Supplied parts acces
13. sories list Powdercoated steel frame and Undercoated timber panel pivot assembly affixed LP Morgan Skyhook Projector Control Unit Mount System including mounting bolts and spacers Wall Switch and Cardboard Dust cover Architrave Mount When unpacking the Flipper please handle all parts with care Do not destroy the folded inner box when unpacking as it is the dust cover for this unit 4 LP Morgan Installation Instructions LP Morgan Flipper Manual Part names Pivot Frame Skyhook Plate Motor Flipper Frame Orientation In use Note motor position and projector orientation LP Morgan Installation Instructions 5 LP Morgan Flipper Manual Dimensions Top View Closed Position Front Back View Closed Position lt gt 6 LP Morgan Installation Instructions LP Morgan Flipper Manual Dimensions Dimension Name Std Flipper Lrg Flipper A Overall Length 575 675 B Frame Width 515 625 C Overall Width 670 770 D Closed Height 84 84 E Face Panel Width 450 550 F LHS Panel Offset 40 40 G RHS Panel Offset 180 180 H Face Panel Length 500 600 l Rear Offset 37 5 37 5 J Front Offset 37 5 37 5 K Operating Height 350 400 Side View Closed Position LP Morgan Installation Instructions 7 L
14. tor Mount and Screen Controls LP Morgan Installation Instructions 21 LP Morgan Flipper Manual Maintenance and Troubleshooting The unit has stopped working and won t go up or down 1 Check that all the terminations are secure that the power supply is plugged in and that the cables are free from damage 2 A light on the power supply indicates power if it is off then the power supply may be damaged 3 Open the black plastic enclosure to expose the control board Switch the power off and on You will see a LED flash on the circuit board which indicates power and that the circuit board is operating correctly 4 Close the Switch Up and Common terminals on the control board refer to page 17 for a wiring diagram If the unit does not move but you hear a clicking sound then the motor may be damaged Contact Herma for advice If you have integrated the Flipper into a control system eg Projector triggering IR repeating Crestron AMX etc then the problem is most likely with the control system Check that the right signal is getting to the Flipper Use the wall switch close the Switch Up and Common terminals to test the unit If it still doesn t work Contact Herma for advice The projector cables get jammed in the pivot frame as it rotates Check that the cutout for the projector cable is on the right side NOT THE MOTOR SIDE You may have it installed upside down Check th

LP Morgan Flipper User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents