KIP 2300 User Manual - KIP
Contents
1. Space for accepting a thick original 2 12 Chapter 2 Basic Operation 5 The Original Guides will prevent the original from skewing during scanning when placed correctly Referring to the size lines on the scanner table place these guides to the locations where the edges of scan original will be Original Guides Ec PE Ll E gt 2 13 Chapter 2 Basic Operation 6 Confirm that the original is face down 7 With aligning both side edges with the Original Guides insert the scan original into the Lower Original Feeder and move it forward until the Lower Original Feeder Indicator starts blinking which notices that the original is enough inserted Leading edge of the original Blinks when original is enough inserted 2 14 Chapter 2 Basic Operation 8 Press the BOARD Button The Document Press Unit moves down and holds the original firmly BOARD Button Document Press Unit This moves down 2 15 Chapter 2 Basic Operation A CAUTION Do not put the hand under the Document Press Unit when it is moving down as the hand will be caught Even if the hand is caught by the Document Press Unit accidentally the scanner automatically detects it and moves up the Document Press Unit within a few seconds for relieving the hand Or the operator can r2. 2 9 Chapter 2 Basic Operation 2 2 2 Scanning a board type original An original thicker than 1 5mm needs to be scanned in the board original mode and it also needs to be fed into the Lower Original Feeder LE am eee Board type original 1 5 through 16 0mm Lower Original Feeder 1 Confirm the Lower Original Feeder Indicator is lighting in green which means the scanner is currently acceptable of original Lower Original Feeder Indicator 2 10 Chapter 2 Basic Operation 2 Move the bottom ends of Rear Steel Trays from normal position to low position which will set the entire Rear Steel Trays to the low flat position Normal position Low position SY gt Normal position Low position A NOTE Please set the Rear Steel Trays to the low position when a board type original is scanned 2 11 Chapter 2 Basic Operation 3 Press BOARD Button to enable the Board Original Feeding Mode The BOARD Lamp lights in green and the Power Lamp blinks in green with waiting the insertion of board original BOARD Lamp lights Power Lamp blinks BOARD Button Press this to enable the board original mode 4 The Document Press Unit moves up when the BOARD button is pressed which allows for accepting thick original by having wide space in the Lower Original Feeder Normal Board Original Feeding Mode
3. KIP 2300 User Manual Version A We highly appreciate your purchasing our KIP 2300 Image Scanner This User s Manual contains functional and operational explanation for KIP 2300 Image Scanner Read this User s Manual carefully before use in order to understand the KIP 2300 Image Scanner completely and to use more efficiently Keep this User s Manual for future reference 1 For U S A This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2 For Europe This equipment complies with the requirements in Pub 22 of CISPR Rules for a Class B computing device Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take whatever steps are necessary to correct the interference Do not install Machine around electronics equipment or precision instruments It may be influenced by electrical reason or vibration while operation If Machine is installed near electronics equipment such as TV or radio interference to equipment such as noise or flickering may be occurred Use separate power line and install Machine as far as such equipment As an ENERGY STAR Partner Katsuragawa Electric Co Ltd has determined that this product meets the ENER
4. Dirt of these parts may result in the image problem or getting dirt on the scan original 4 1 1 Document Glass Open the scanner upper unit Wipe the Document Glass with a soft cloth with a little water or with neutral detergent first and wipe it with a dry soft cloth Document Glass 4 2 Chapter 4 Maintenance Ah CAUTION The Document Glass can be removed if the thumb screws on both sides and the brackets are removed But do not touch this screw as only the service technician is allowed for removing the Document Glass If the Document Glass is removed some foreign substance may drop into the machine and may cause several troubles as short circuit Do not touch this screw 4 3 Chapter 4 Maintenance 4 1 2 Platen Wipe the entire white part of the Platen with a soft cloth with a little water or with neutral detergent first and wipe it with a dry soft cloth Platen Clean the entire white part 4 4 Chapter 4 Maintenance 4 1 3 Feed Rollers Wipe the Feed Rollers with a soft cloth with a little water or with neutral detergent first and wipe it with a dry soft cloth Feed Rollers 4 5 Chapter 4 Maintenance Feed Rollers 4 6 Chapter 4 Maintenance Feed Rollers 4 7 Chapter 4 Maintenance Image Scanner KIP 2300 User s Manual Version A 1 Published by Katsuragawa Electric Co Ltd 21 1 Shimomaruko 4 Chome Ota ku Tokyo 146 8585 Japan All rights reserved Please note that some ar
5. 6 10 Frequency 50 or 60Hz Max power consumption Less than 120W Average power consumption US 120V During scanning Stand by In Power Save Mode EUR ASIA 200 240V During scanning Stand by In Power Save Mode Dimension 1 366mm Width x 543mm Depth x 318mm Height NOTE Original Guides Original Tray and Pedestal are excluded Weight About 76kg Environmental conditions Temperature 10 32 degrees centigrade Humidity 15 85 RH No dew Recommended 23 degrees centigrade and 60 RH No dew Acoustic noise Stand by Less than 55db During scanning Less than 60db Impulse sound Less than 70db Stacking capacity of trays Front Steel Tray Max number of originals about 20 sheets of 36 x48 Max weight of originals 2 2kg square meter Rear Steel Tray Max number of originals about 50 sheets of 36 x48 Max weight of originals 5kg square meter A NOTE Specifications may change without notification 1 6 Chapter 1 Before Use 1 4 Name amp Function of Each Part 1 4 1 Front view 1 7 Chapter 1 Before Use Name Function ss Upper Original Feeder Upper Original Feeder accepts a sheet type original that is 0 05 1 49mm in thickness Please set the original with face down The original fed from here Feeder is ejected to the front side of scanner via Lower Original Feeder Lower Original Feeder Lower original Feeder accepts not only a sheet type
6. It may cause a fire or receiving an electric shock Do not step on the power cord and do not damage or process it It may also cause a fire or receiving an electric shock Do not tie the power cord or make a knot on it It may also cause a fire or receiving an electric shock Do not put a flower vase a flowerpot or a water filled glass on the top of the machine If the water spilt out it may also cause a fire or receiving an electric shock If the machine generates abnormal smell or noise turn it off and then disconnect the power plug from the outlet necessarily Do not handle the power plug with the wet hand positively It may cause to receive an electric shock Insert the power plug into the outlet completely If the power plug is not inserted completely it may cause a fire Use only the attached power cord Make sure to catch the Plug when you unplug the machine Otherwise you may break the cord and may result in a fire or receiving an electric shock Do not disassemble or tamper the machine Otherwise it may cause a fire or receiving an electric shock CAU TION Do not install the machine at the following places 1 Humidified or dusty place 2 Unstable floor When the machine comes down it may cause the injury Be careful not to catch your hand between Upper Unit and Main Unit when you close the Upper Unit Unplug the machine before you move it to another place Otherwise the power cord
7. This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may Cause undesired operation 2 For Europe This equipment complies with the requirements in Pub 22 of CISPR Rules for a Class B computing device Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take whatever steps are necessary to correct the interference Do not install Machine around electronics equipment or precision instruments It may be influenced by electrical reason or vibration while operation If Machine is installed near electronics equipment such as TV or radio interference to equipment such as noise or flickering may be occurred Use separate power line and install Machine as far as such equipment 1 3 Chapter 1 Before Use 1 2 Features Large format full color image scanner KIP2300 is a full color image scanner that provides various copy scan operations with being combined with KIP IPS controller It provides the following 4 modes for scanning and copying 24 bit color mode 8 bit gray mode 4 bit gray mode Binary black amp white mode Recognizable of various original widths KIP 2300 Scanner can recognize the following kinds of standard original widths as well as any non standar
8. Receives the original ejected from the scanner after scanning Max number of originals about 50 sheets of 36 x48 Max weight of originals 5kg square meter 6 7 1 8 Chapter 1 Before Use 1 4 2 Rear view Name Rear Counter Rollers Help to transport the original when ejected 2 USB Terminal USB cable is connected Connected to the PC Type B Connector 3 3V max HIL Terminal HIL Connector is connected Connected to the PC 3 3V max Inlet Power cord is connected 1 9 Chapter 1 Before Use 1 5 Specifications for Scan Original 1 5 1 Originals Prohibited from Duplication It may be illegal to duplicate or copy certain types of originals and you may be punished by local or regional laws if copies are made of these types of originals Please be aware of your local or regional laws and which originals they forbid you to duplicate some Examples Originals prohibited from copying by the law s 1 Do not copy Currency Bill Money Bank Note etc Government issued Negotiable Instruments National Bonds Security Local Debt Bonds etc 2 Do not copy Foreign Currency or Foreign Negotiable Instruments 3 Do not copy unused postal stamps or government postcards without permission to make replica from said Governments 4 Do not copy Government issued revenue stamps certificate stamps that are prescribed by Liquor Tax Act or the Commodity Tax Act Special items which require yo
9. may be damaged and may result in a fire or receiving an electric shock If nobody operates the scanner in the night time make sure to turn it off for the safety If nobody operates the machine for a long time during consecutive holidays make sure to turn it off for the safety Nothing should be put near the power plug so as to disconnect it quickly anytime LED Safty Safty of LED Products Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure As the LED on the Light Source PCBs PW12130 amp PW12131 are Class 2 LED singularly it is not allowed for using it with disassembling or converting Classification of LED product CLASS 1 LED PRODUCT IEC 60825 1 2001 EN 60825 1 1994 A2 2001 A1 2002 Maximum class of the embedded LED CLASS 2 WHITE LED Maximum power 4 0mW POWER CORD INSTRUCTION The installation of or exchange to a power plug which fits in the wall outlet of the installation location shall be conducted in accordance with fallowing A WARNING Selected a power plug which meets the following criteria The plug has a voltage and current rating appropriate for the product s rating marked on its name plate The plug meets regulatory requirements for the area The plug is provided with a grounding pin or terminal If the appropriate plug does not fit the wall outlet in the installation the customer
10. shall install an appropriate outlet Connector Type Configuration Standard Usually found in 1EC60320 C13 7A 250V IEC 7A 125V UL Configuration Standard Usually found in CEE7 7 TA 250V European countries KS C 8305 TA 250V Korea AS NZS 3112 TA 250V Australia New Zealand GB1002 TA 250V China GB2099 1 RAM 2073 TA 250V Argentina ii _ SASO 2203 TA 250V Saudi Arabia BS 546A TA 250V British IS 1293 India SABS 1293 South Africa Configuration Standard Rating minimum Usually found in ange NEMA 5 15P 7A 125V US Canada SS UL Listed Power Cord e Set only 5 Cord Type a Te II ON Usually found in SVT 3X18AWG SVT 3X18AWG Long lt 2 4m lt 2 4m TA I7A125V North America HO5VV F 3X0 75mm TA 250V European countries Argentina RVV 3X0 75mm 7A 250V 1 1 Chapter 1 Before Use page Installation Requirements ci su Se ast eae eet Gear tha A a ds 2 Features O A a A A A Et aa d au Da a au A asa 6 alt 1 4 Specifications Phere eta hdc Mc ata gt Iona es ashe ts tee cn intaia Peete cota et ie audi tava Pe aa Neat deal aut E 1 5 Name amp Function of Each Part sola z do de i AA T ne foaia BD an AE ety cotit ata a E actul antec te amines oom A 1 Front view sit adi TAS ANA A a dadu NR OS 1 T 2 Rear view E tao E aaa baia ata Ei e OT Or 1 9 Specifications for Scan Original n adanca ada acad aia i la Sa Aaa 1 1 0 1 Originals Prohibited from Duplication sasi masina dani ama leii C E EE
11. to the outlet via the power cable A WARNING 1 Do not handle the power plug with a wet hand It may result in receiving an electrical shock 2 Ground the machine for safety 3 Please connect to a dedicated outlet Many loads on a single outlet may cause overheating and result in a fire 4 The outlet must satisfy 100 240V 6 10 50 60Hz 6A or higher 3 Turn on the KIP2300 scanner pressing the bar side of Power Switch on the left Press this side for turning on 4 Scanner takes initialization It takes about 10 seconds for the initialization and the scanner does not accept original insertion during this period which is shown by green flash of Power Lamp Power Lamp flashes before ready 2 2 Chapter 2 Basic Operation 5 Scanner gets ready when all the initializations are finished which is shown by continuous lighting of Power Lamp in green Power Lamp lights when ready 2 3 Chapter 2 Basic Operation 2 2 Scanning an Original 2 2 1 Scanning a sheet type original A sheet type original can be fed from both upper and lower original feeders Upper original feeder accepts 0 05 to 0 1mm in thickness Lower original feeder accepts 0 05 to 1 5mm in thickness Upper Original Feeder Sheet type original 0 05 through 1 0mm Lower Original Feeder 1 Using the Upper Original Feeder The thicknes
12. E EA 1 10 2 Specifications for the scan original EAS EA AS a aaa 1 1 1 1 1 Chapter 1 Before Use 1 1 Installation Requirements The following conditions have to be satisfied when installing the KIP2300 Scanner 1 Satisfy the following input power condition Voltage v 100 240V 6 10 Current ees GA or higher Frequency 50 or 60Hz KIP2300 can be connected to the outlet simply so far as the voltage is within 100 240V 6 and 10 are acceptable 2 Connect the power plug to the grounded outlet 3 To completely disconnect the equipment from the power source please draw the power plug from the outlet The outlet must be easily accessible near the equipment 4 The temperature must be within 10 through 32 degrees centigrade and the humidity must be within 20 through 80 5 Keep the equipment away from fire dust and direct sunlight If it is impossible to avoid the direct sunlight please pull the curtain to intercept the sunlight 7 Keep enough space around the machine as follows The following values are the least requirements Please keep a wider space if possible A 1600mm Rear side a KIP2300 Front side 1000mm 2000mm is required if the original is thicker than 1 2mm 1 2 Chapter 1 Before Use Reference Machine Noise Information Ordinance 3 GSGV January 18 1991 The maximum sound pressure level is equal or less than 70dB A according to ISO 7779 A NOTE 1 For U S A
13. GY STAR guidelines for energy efficiency ENERGY STAR The International ENERGY STAR Office Equipment Program is an international program that promotes energy saving through the penetration of energy efficient computers and other office equipment The program backs the development and dissemination of products with functions that effectively reduce energy consumption It is an open system in which business proprietors can participate voluntarily The targeted products are office equipment such as computers monitors printers facsimiles copiers scanners and multifunction devices Their standards and logos are uniform among participating nations The symbol shown indicates that this product conforms to Directive 2002 96 EC of the European Parliament and the council of 27 January 2003 on waste electrical and electronic equipment WEEE and does not apply to countries outside of EU Only For EU Member States The symbol shown indicates that this product conforms to SJ T11364 2006 of People s Republic of China Electronic Industry Standard and does not apply to countries outside of People s Republic of China The symbol shown indicates that this product conforms to GB 18455 2001 11364 2006 of National Standard of the People s Republic of China and does not apply to countries outside of People s Republic of China WARNING FOR THE SAFETY OBSERVE THESE WARNING Following warnings are very important to use this equ
14. P2300 Image Scanner Desktop scanner 3 CCD Reduction Optical System 3 CCD of RGB 7450 pixels Main scanning horizontal direction Sub scanning vertical direction Range of Scan Resolution 100 2400dpi Scan mode Binary mode 4 bit gray mode 8 bit gray mode 24 bit color mode Scanning method Sheet through type Scan speed Monochrome Gray mode 100dpi 12 sec lower feeder 5 sec upper feeder 600dpi 5 sec lower feeder 5 sec upper feeder 2400dpi 1 25 sec lower feeder 1 25 sec upper feeder Color Mode 100dpi 12 sec lower feeder 5 sec upper feeder 600dpi_ 2 sec lower feeder 2 sec upper feeder 2400dpi 0 5 sec lower feeder 0 5 sec upper feeder Original type Sheet type amp board type Upper original feeder can accept 0 05 0 1mm Lower original feeder can accept 0 05 16 0mm Maximum reading width 914 4mm 36 Transportable original length Transportable original width Thickness of original Interface USB 2 0 for controlling amp image data transfer HIL High speed Image Link for image data transfer NOTE Connected PC needs to have a PCI Express card slot for installing the HIL Add in Card Memory capacity From 256MB standard to 2GB Option A NOTE Specifications may change without notification 1 5 Chapter 1 Before Use Power source Voltage 100 120V 6 10 200 240V 6 10 Note Scanner accepts any voltage so far as it is within 100 240V
15. anner when 15 minutes of inactive period has passed Please turn on the scanner again with the Power Switch for using the scanner again 277 Power switch 2 20 Chapter 2 Basic Operation 2 6 Removal of Trays 2 6 1 Front Steel Trays The Front Steel Tray can be removed when unnecessary or for saving the space Please do as instructed in below 2 21 Chapter 2 Basic Operation w B w A then moving up as arro 2 Remove the Front Tray BKT 3 2 by twisting as arro it upper un rs 3 to open the scanner 3 Pull up both blue leve Chapter 2 Basic Operation 2 22 4 Remove the Front Tray BKT 2 4 on the right ye A 4 5 Remove the Front Tray BKT 1 5 on the left 6 Close the scanner upper unit finally 2 23 Chapter 2 Basic Operation 2 6 2 Rear Steel Trays The Rear Steel Tray can be removed when unnecessary or for saving the space Please do as instructed in below 1 Move up and remove the Rear Steel Trays 1 2 24 Chapter 2 Basic Operation Chapter 3 Troubleshooting page 3 1 Original Misfeeac iii nete etalon aes 3 2 3 1 When feeding into upper original feeder re cereale ap eta 3 2 3 2 When feeding into upper original EPIA ae 3 4 3 2 EFROS sooo era es ee acte Pia A A d cada aa la lata aa 3 5 3 1 Chapter 3 Troubleshooting 3 1 Original Misfeed When the original is mis fed du
16. d widths ranging from 210mm to 1066 8mm 42 Metric standard original widths AO A1 A2 A3 A4 36 Engineering Architecture widths 36 34 30 24 22 18 17 12 11 8 5 High resolution scanning KIP2300 scanner s 600dpi optical resolution allows for producing high quality scan copy image from various types of original image Scan resolution can be increased or decreased between 100 and 2400dpi as required Acceptable of extensive original thickness KIP2300 accepts a sheet type original as well as a board type one The acceptable thickness range is from 0 05mm to 16 0mm Dual original feeders The lower original feeder accepts all supported thicknesses and sizes of originals The original is set with face down and ejected to the rear tray The upper original feeder accepts all sizes of sheet type original that is thinner than 1 49mm The original is set with face up for enabling an operator to check the image or orientation before scanning The original fed from the upper original feeder is ejected from the lower original feeder High speed data transfer If the HIL Card is installed onto the KIP IPS or network PC connected with KIP2300 and KIP2300 scanner is connected to the IPS with dual cables USB 2 0 cable and HIL cable the data transfer from scanner to IPS can be accomplished much faster NOTE PCI Express slot is required for accepting HIL Card 1 4 Chapter 1 Before Use 1 3 Specifications KI
17. elieve his hand by Scanner upper unit opening the scanner upper unit with pulling either one of blue levers Blue levers 9 The scanner automatically detects the width of original then moves the original to the front side for placing it at the start position 10 KIP2300 starts scanning automatically or manually according to the operation on the controller software 2 16 Chapter 2 Basic Operation 10 The original is ejected to the rear side and stacked on the Rear Steel Tray 2 17 Chapter 2 Basic Operation 2 3 Cancellation of Current Scan 1 Press of the Stop Button during scanning will cancel current scan and the KIP2300 stops original feeding Stop button 2 One more press of the Stop Button will eject the original to either front or rear accordingly to the location of original When removing a very thick board type original do not open the scanner upper unit as the following example Please eject it by pressing the Stop button as instructed in the above Scanner upper unit 2 18 Chapter 2 Basic Operation 2 4 Turning OFF the KIP 2300 Turn off the KIP2300 scanner pressing the bar side of Power Switch on the left a Press this side for turning off 2 19 Chapter 2 Basic Operation 2 5 Auto Power OFF KIP 2300 has Auto Power OFF feature for energy saving purpose which automatically switches off the sc
18. ipment safely and to prevent the operator from danger and his her property from being damaged Hazardous or damage degree is classified and shown as follows when this machine is erroneously used ignoring this USER S MANUAL WARNING This caution mark denotes that the failure to follow given instructions in handling the machine could result in a death or serious injury CAUTION This caution mark denotes that the failure to follow given instructions in handling the machine could result in an injury or physical damage only This symbol signifies what must not be done This symbol signifies General Mandatory Action WARNING Connect the scanner and Ground with each other surely with the grounding wire Otherwise it is dangerous for you if you receive an electric shock or at the time of lightning If the outlet does not have a Grounding Terminal or if it is impossible to connect call the vendor or service professional for the installation Power source should be rated from 100V 240V 6 10 6A or higher and 50 60Hz It is preferable that the used power circuit is provided with a dedicated breaker Install the machine as close as possible to the outlet When you wish to move the machine to another place make sure to ask your service engineer Do not use a multi wiring connector that might raise the temperature of the outlet abnormally and cause a fire Do not put anything heavy on the power cord
19. mm 1 Confirm the Lower Original Feeder Indicator is lighting in green The original can be accepted only when it is lighting in green Lower Original Feeder Indicator 2 The Original Guides will prevent the original from skewing during scanning Move them onto the Lower Original Feeder if on the Upper Original Feeder Then according to the width of scan original align the inside edge of Original Guides to the concerning size lines on the table Original Guides 2 7 Chapter 2 Basic Operation 3 Confirm that the original is face down 4 Aligning both side edges with the Original Guides insert the scan original into the Lower Original Feeder until the leading hits the feeding roller Wait a few seconds with contacting the leading edge to the feeding rollers until the scanner starts transporting 5 A few seconds later the scanner automatically transports the original a little to the rear side to detect its width After that the original is moved back to the front side 2 8 Chapter 2 Basic Operation 5 KIP2300 starts scanning automatically or manually according to the operation on the controller software The lower original feeder will transport the original very quickly especially when low scan resolution is selected in the monochrome gray mode Be careful not to touch the edge of original during transportation so as not to be harmed 6 The original is ejected to the rear side and stacked on the Rear Steel Tray
20. n label 1 11 Chapter 1 Before Use Folded Leading edge Uneven thickness Curled Diameter of curl must be larger than 80mm Irregular shape Not square Wet Ink is not dried Made of metal or cloth Chapter 1 Before Use Clipped or stapled Clipped Stapled 7 Rough surface Carbon paper for example Rough surface Dusty Electrically changed Photograph 1 13 Chapter 1 Before Use Chapter 2 Scanner Hardware Operation page 2 1 Turning ON the KIP2300 A iia Za 2 2 2 Scanning an Original ee A 2 4 2 2 1 Scanning a sheet type original ER EEEE AERE E E E E EAE aie er 2 4 1 Using the Upper Original ESBOBr iaa a Ei ac taiat aaa 2 4 2 Using the Lower Original e ccm cee ene 2 7 2 2 2 Scanning a board type original dd e Tal ade te 2 10 2 3 Cancellation of Current Scan NN 2 18 2 2 Turning OFF the KIP 2300 AI AA NAAA LAA AAA A AAA E EIA AAA ASA pei odata La vitala 2 19 2 5 Auto Power OFF AAA AA AAA AAA AREA AAA AAA AA c la 2 20 2 6 Removal of Trays eens clay II IO DICA DR PARI A a a A Re E C Aechmea tates A AII 2 27 2 6 1 Front Steel Trays a Mera NATE EE RUA sea aaa Mead c aaa tota a 2 27 2 6 2 Rear Steel Trays sie us Bots A oaia at ads coat d ua ta cl 2 24 2 1 Chapter 2 Basic Operation 2 1 Turning ON the KIP 2300 1 Prepare a power cable that satisfies the following specifications 2 Connect the KIP2300 scanner
21. original that is 0 05 1 49 in thickness but also a board type original that is 1 5 16 0mm in thickness Please set the original with face down The original fed from here is ejected to the rear side of scanner and received by the Rear Steel Tray Indicator insertion and does not light when it can not accept Lower Original Feeder This lights green when the Upper Original Feeder can accepts original Indicator insertion and does not light when it can not accept And in the Board Original Mode it blinks green when the scanner detects original size These guides can be shifter left and right according to the original width and prevent the original from skewing during scanning Board Lamp lights green when the Board Original Mode is enabled Stop Button amp Lamp Pressing the Stop Button during scanning will stop scanning and original transportation in the middle and one more will eject the original to either front or rear Power Lamp This shows the status of scanner Blinking in green During initialization not ready Lighting in green Ready for scanning or during scanning Lighting in orange Scanning original transportation is paused Blinking in orange Ejecting the original Lighting in red Scanner has any error 10 Front Steel Tray Helps feeding a board type original into the Lower Original Feeder Max number of originals about 20 sheets of 36 x48 Max weight of originals 2 2kg square meter Rear Steel Tray
22. ring scanning remove it manually as instructed in below 3 1 When feeding into upper original feeder 1 Open the document upper cover with holding both sides Document upper cover Hold here when opening the document upper cover 2 Pull up both blue levers to open the scanner upper unit Blue levers 3 2 Chapter 3 Troubleshooting 3 Remove the mis fed original Mis fed original Ah CAUTION Take cere not to catch your hand when closing the document upper cover or scanner upper unit 3 3 Chapter 3 Troubleshooting 3 2 When feeding into lower original feeder 1 Open the scanner upper unit by pulling up the blue levers on both sides Blue levers 2 Remove the mis fed original Mis fed original A CAUTION Take cere not to catch your hand when closing the scanner upper unit 3 4 Chapter 3 Troubleshooting 3 2 Error The Power Lamp lights in red when the scanner has any error See the description of error indicated on the controller monitor and correct the error appropriately Power Lamp lights in red when any error occurs 3 5 Chapter 3 Troubleshooting Chapter 4 Maintenance page 4 7 Cleaning o aa ate ai a n tsi au 4 2 4 1 7 Document GASS nica A ANI ES AE tate d ata 4 2 4 1 2 Platen censeo a ee 4 4 41 2 Feed Rollers tin AO 4 5 4 1 Chapter 4 Maintenance 4 1 Cleaning It is recommended to clean Original Glass Platen and Feeding Rollers once a week or as needed
23. s of original that the upper original feeder can accept is from 0 05 to 0 1mm 1 Confirm the Upper Original Feeder Indicator is lighting in green The original can be accepted only when it is lighting in green Upper Original Feeder Indicator 2 4 Chapter 2 Basic Operation 2 The Original Guides will prevent the original from skewing during scanning Move them onto the Upper Original Feeder if on the Lower Original Feeder Then according to the width of scan original align the inside edge of Original Guides to the concerning size lines on the table Original Guides 3 Confirm that the original is face up Aligning both side edges with the Original Guides insert the scan original into the Upper Original Feeder until the leading hits the feeding roller Wait a few seconds with contacting the leading edge to the feeding rollers until the scanner starts transporting 4 A few seconds later the scanner automatically transports the original a little to the rear side to detect its width After that the original is moved back to the front side 2 5 Chapter 2 Basic Operation 5 KIP2300 starts scanning automatically or manually according to the operation on the controller software The original is turned and ejected to the front side via Lower Original Feeder 2 6 Chapter 2 Basic Operation 2 Using the Lower Original Feeder The thickness of original that the lower original feeder can accept by normal mode is from 0 05 to 1 5
24. ticles illustrations and photographs might be partially different from the actual machine because of the modification of machine and so on
25. ur attention 1 The government issues warnings if you are to copy private issued securities stock certificate draft check goods ticket etc commutation ticket or book of tickets excluding that some specific company copies such originals as many as it requires for its own business 2 We recommend you not copy originals as government issued passports public or private issued licenses automobile inspection certification ID and tickets passes or meals Originals protected by the copyright It is prohibited to copy originals such as books music paintings printed copies maps drawings movie posters and pictures which are protected by the copyright laws Please see your local or regional laws 1 10 Chapter 1 Before Use 1 5 2 Specifications for the scan original Original s thickness which KIP2300 scanner accepts is 0 05 through 16mm Originals are divided into 2 types such as sheet type and board type in terms of the thickness Sheet type 0 05 through 1 49mm Board type 1 50 through 16 0mm IA we LE LE LZ gt a e ne Sheet type original Board type original 0 05 through 1 49mm 1 50 through 16mm The available original size differs according to the type ss Sheet type Board type Length 210 through 16000mm 210 through 1219mm Width 210 through 1066 8mm 210 through 914mm Weight A 22g square meter Do not scan the following types of original as it may damage the original or scanner itself With stick o
Download Pdf Manuals
Related Search