Australian Arrow Boards User Manual
Contents
1. Optional Beacons On Off Optional ogaggogoodo User Manual V1 1 5 Australian Arrow Boards eperation sinigie sicded Turn on Board Press once to activate arrow board amp controller Illuminated LED indicates power on Press again to turn board off NOTE The controller will emit a feint beeping until it is turned on if it senses a power supply Tilt Board Up Down Rack Mounted Boards Only Electric operation optional Press once to activate electric actuator Flashing LED indicates actuator in operation Steady on LED indicates actuator operation has stopped NOTE Pressing the Tilt Up or Down button whilst the actuator is in motion will stop the board in it s current position Recommence or change direction by pressing the desired button once Caution Always check to make sure there are no obstructions before tilting the board up or down Australian Arrow Boards 6 June 2010 Tilt Board Up Down Rack Mounted Boards Only cont Manual operation Tilt Up Using the handle integrated into the passenger side of the board push with a steady motion until the gas strut takes the weight of the board and guide the board gently into it s upright position Tilt Down Using the handle integrated into the passenger side of the board pull back with a steady motion until the gas strut releases the weight of the board and guide the board into it s down posi2. bulbs not working replace bulb s if beacon s are not rotating have wiring amp beacons checked by auto electrician if condition persists replace beacon s Turn board off Wait a minimum of 15 seconds then turn on again if condition persists have wiring amp connection checked by auto electrician controller may need replacing 15 Australian Arrow Boards Specincation s Model Name AAB AB AAB AB DBL AAB BB AAB BB DBL AAB CB Board 1262mm 1262mm 1502mm W 1502mm 2400mm W Dimensions 160mm ja 270mm a 160mm D 270mm a 270mm D 2mm 662mm H 662mm H 772mm H 772mm H 1200mm H Controller 120mm W 120mm W 120mm W 120mm W 120mm W Dimensions 31mm D 31mm D 31mm D 31mm D 31mm D 69mm H 138mm H 69mm H 138mm H 69mm H No of Lamps 13 26 15 30 15 17 Facility for 2 lamps on rear of board Current Draw 21A 4 2 A 2 5A 5 0 A 2 5A Operating Voltage 11 5 13 5 VDC Weight Board Only 16 0 Kg 18 7 Kg 21 6 Kg 25 3 Kg 80 Kg Weight Board including 26 2 K 28 3 K 31 2 K 34 9 K N A Rack amp Electric Ang 39 Aag 39 Actuator Power Harness 10 m Controller 15m Harness perating 10 C to 60 C emperature IP Rating Board ve Lamp Dimming EGE Automatic 5 levels below 1100 Ix Full brightness at 1400 Ix and above Australian Arrow Boards 16 June 2010 User Manual V1 1 17 Australian Arrow Boards HSE atone Detalll s Note This User Manual is to rema
3. or lamp harness Controller and Arrow Board have lost communication Arrow Board has entered Fail Safe Mode Controller and Arrow Board have lost communication Arrow Board has entered Fail Safe Mode Light sensor obstructed or malfunction Light sensor malfunction Beacon s wiring or connectors damaged or beacon s faulty Controller malfunction User Manual V1 1 r If vehicle is not running Start engine to bring voltage up to normal range if condition persists have electrical system checked by auto electrician As Above Have lamp connectors checked by auto electrician if condition persists replace affected lamp s Turn board off If safe remove obstruction amp turn on board Have wiring amp connection to actuator checked by auto electrician If condition persists replace actuator Have wiring checked by auto electrician If condition persists replace affected lamp s Disconnect board from power Wait a minimum of 15 seconds then reconnect power if condition persists have wiring amp connection checked by auto electrician controller or control board may need replacing As Above Clear obstructions dirt etc from sensor if condition persists have wiring checked by auto electrician if condition persists replace light sensor Have sensor connector checked by auto electrician if condition persists replace sensor unit if beacon s are rotating but
4. FAS 5 Australian Arrow Boards User Manual A Board AAB AB AAB AB DBL B Board AAB BB AAB BB DBL C Board AAB CB N24440 iMTe OCureron Thank you for purchasing an Australian Arrow Boards product For installation instructions please refer to the Australian Arrow Boards Installation amp Repair manual Australian Arrow Boards products conform to Australian Standards AS4192 2006 RTA NSW RTA FAS 5 A Board 1005 FAS5 01A B Board 1005 FAS5 01B C Tick No N24440 Lamps NATA Certified Report No V080404 03 Australian Arrow Boards 2 June 2010 Contents Page Introduction 2 Contents 3 Arrow Board Components 4 Controller Components 5 Operation Single Sided Board 6 Operation Double Sided Board 10 Warranty Statement 12 Trouble Shooting Guide 13 Specifications 16 Installation Details 18 User Manual V1 1 3 Australian Arrow Boards oO 7 Australian Arrow Boards Integrated Handle Gas Ram Board Rack Assembly Optional Light Sensor Access Panel to Control Board Electric actuator Optional LED Lamp with Visor Board Housing 4 June 2010 eornt olle ARROW SEQUENCE as viewed by Traffic Approaching Board TILT UP AUSTRALIAN ARROW BOARDS ry O BOTH QO HAZARDO RIGHT ON OFF TILT DOWN Selected Sequence Display Left Arrow Both Arrows Hazard Right Arrow Board On Off Actuator Tilt Down Optional Actuator Tilt Up
5. cates power on Press again to turn off FRONT board FRONT Board Arrow Sequences Press once to activate required sequence Steady on LED indicates selected sequence Press again to turn off sequence or Select a different sequence by pressing desired button once O tert som QOHaAzARDC RIGHT GeeS gt T BUZZER SOUNDS see hands Australian Arrow Boards 10 June 2010 Note Selected sequence display flashes in real time with the corresponding lamps on the arrow board Caution Arrow sequences on the FRONT amp BACK BOTH ARROW SEQUENCES SWITCHED 7 5 i AS VIEWED FROM REAR OF VEHICLE board are shown on their displays as they a a ALIAN ARROW BOARDS would be viewed from traffic HAZARD RIGHT ON OFF approaching the rear of your vehicle User Manual V1 1 11 Australian Arrow Boards Wearrrarttyastaternrerit Australian Arrow Boards products are built to exacting standards and are covered by a component replacement repair amp return warranty against faulty workmanship and or material components 5 years on lamps Lamps will be replaced under warranty should 9 individual LEDs fail to illuminate 2 years on electronics amp hardware Board controller amp electronics housing amp mounting hardware including the optional electric actuator will be either repaired or replaced during this period Labour costs are not covered under wa
6. in with the vehicle to which the board has been installed Installation Date Installer Name Address Board Model ca ee ee eee ae ee ae eee Board Serial NUM er a Options Installed Rack Assembly oo 1 sun Yes No mn Electric Actuator mmm LES NO cnn Beacons Yes No Venicle TYPE asp ee ee Vehicle VIN Australian Arrow Boards 18 June 2010 This publication is copyright All rights reserved This publication may not be reproduced in full or in part by any means electronic or mechanical without the prior written permission of Australian Arrow Boards User Manual V1 1 19 Australian Arrow Boards Australian Arrow Boards Froad urmner ee PE www roadrunnerparts com au Unit 2 42 44 Whyalla Place Prestons NSW 2170 PO Box 314 Menai Central NSW 2234 Phone 02 9607 5774 Fax 02 9607 5589
7. rranty Caution There are no user serviceable components in the controller or the board Any repairs that are needed to wiring connectors or internal components must be undertaken by a qualified auto electrician Failure to do so may void your warranty Australian Arrow Boards 12 June 2010 TFOUDIesHOOottG All Australian Arrow Boards include a range of self diagnostic capabilities built in to ensure the safe operation of your board The controller and the board communicate with each other once every two seconds to ensure everything is working as it should and if a fault is detected the operator will receive feedback via a buzzer within the controller There are 3 types of audible feedback that you may hear from the controller Short fast beeps Long slow beeps Continuous buzz The table on the following page will allow you to determine what fault may have occurred and the steps needed to fix the problem User Manual V1 1 13 Australian Arrow Boards Board Condition Controller Condition SI Fast Fast Slow Continuous Continuous Continuous Continuous Arrow Sequence changes to Hazard pattern Arrow Board has no lamps working Arrow Sequence missing lamp or lamps Board not fully in up or down position Board can be in any position Currently selected Arrow Sequence remains in operation No lamps on board operational Board has switched automatically from selected pat
8. tern to Hazard pattern Board has switched automatically from selected pattern to Hazard pattern Lamps dull during daylight operation Lamps full brightness during night time operation Normal Arrow Board functions Beacon s not working Normal Arrow Board functions Beacon s not working Arrow sequence display shows Hazard pattern Controller switched off No LEDs illuminated Arrow Sequence display has LEDs not illuminated Tilt Up or Down LED flashing Tilt Up or Down LED flashing Unable to change Arrow Sequence May be possible to select a different Arrow Sequence Arrow Sequence display has automatically changed from selected pattern to Hazard pattern Controller switched off No LEDs illuminated Full functions Full functions Beacon indicator LED illuminated Beacon LED indicator fails to illuminate when activated Australian Arrow Boards 14 June 2010 Power supply has reached low voltage 11 6V Power supply has reached extreme low voltage 10 8V or Power supply has reached over voltage 15 7V 1 or more lamps corresponding with the Arrow Sequence display have a faulty connection or have failed Arrow Board has been obstructed during Tilt Up or Down operation Power to actuator has been isolated to prevent further damage Short circuit detected in actuator or actuator wiring Power to actuator has been isolated to prevent further damage Short circuit in lamp
9. tion Caution DO NOT release the handle and let the board crash into position This will reduce the life expectancy of your arrow board and damage incurred by such operation will not be covered under warranty User Manual V1 1 7 Australian Arrow Boards Operation singles sicdlecmcent Beacons Optional Press once to activate beacon circuit Steady on LED indicates circuit is on Press again to turn off beacon circuit BEACON Arrow Sequences Press once to activate required sequence Steady on LED indicates selected LEFT BOTH Q HAZARD RIGH sequence cS fo 3 Press again to turn off sequence ULT BUZZER SOUNDS see handbook or Select a different sequence by pressing desired button once RROW SEQUENCE as v Note Selected sequence display flashes in real time with the corresponding lamps on the arrow board Australian Arrow Boards 8 June 2010 ARROW SEQUENCE as viewed by Traffic Approaching Board Caution EE Arrow sequences are shown on the display as they would be viewed from traffic approaching the board User Manual V1 1 9 Australian Arrow Boards ODeratior Double sided Note The BACK Board operation of a Double Sided board is the same as the operation of a Single Sided board O on orF Turn On FRONT Board Press once to activate FRONT board amp the FRONT board controls Illuminated LED indi
Download Pdf Manuals
Related Search