Tempus User Manual v1.01 0106
Contents
1. The day flashes With the up down arrow keys change the day Push the right arrow key the month flashes Change the month with the up down arrow keys Push the right arrow key the year flashes Change the year with the up down arrow keys The new date starts by leaving this function pressing the right arrow key If you don t want to change the date leave this function with the left arrow key press 1x or 2x TEMPUS 5 Version 1 01 TOWER CLOCK Set or correct the tower clock For the master to be able to automatically set or correct the tower clock it is essential to enter the time displayed on the clock dial Press the down arrow key until Tower Clock appears in the display The output turns off 2 TOWER CLOCK ZO Enter this function with the right arrow key The output turns off and the tower clock stops Take a look at the tower clock face and enter the time displayed on the dial D a MOO Q The hours flash With the up down arrow keys set the hours to the same hour as displayed on the dial Then push the right arrow key again The minutes flash With the up down arrow keys set the minutes to the same time as displayed by the minute hand on the dial Press the right arrow key to confirm The setting process starts automatically The master compares the dial time which was just entered with the internal quartz timebase and corrects the clock If the time difference is 40min or less ahead of time the tower cl2. like time and date slave clocks tower clock synchronisation turning bell hammers on off etc The function menu allows the installer to set the system parameters e g impulse type impulse duration programming relays and bell hammers This menu can be protected against unauthorised changes by a security PIN code BACKLIGHTING All Tempus versions provide display backlighting for comfortable programming in poor lighting conditions TEMPUS 1 Version 1 01 2 Options Following options are available for the Tempus controller OPTIONAL EXTERNAL SYNCHRONIZATION Three time code receivers are available for synchronisation DCF Time Code Europe only This receiver is available for most of mainland Europe The Tempus accuracy will not deviate for more than 1 sec from Middle European time MSF Time Code UK only This receiver is available for the UK area The Tempus accuracy will not deviate for more than 1 sec from Western European time GPS Receiver world wide The GPS receiver can be used anywhere in the world It receives the atomic time from 24 satellites revolving around the earth The Tempus accuracy will increase to within 100uS from GMT UTC COMPUTER LINE This option enables the transfer of time and date via the RS232 serial code to a computer via remote control transferring data load pattern OPTIONAL PIM The PIM Plug In Memory Module enables the back up of the Tempus program and allows software transferral fr
3. CCAMPA TEMPUS USER S MANUAL Version 1 01 06 2001 12 47 36 08 10 0000 J tempus Australian Agent E EO BE HERTZ ELECTRON 086 6 0 cs A BN 69 51 4 PO Box 115 ANNANDALE NSW 2038 18 Rose Street ANNANDALE NSW 2038 PH 61 2 8205 0575 FAX 61 2 9571 9754 Email sale hertzelectronics com dau www hertzelectronics com adau A GENERAL 1 Introduction The TEMPUS master clock has been designed for controlling electro mechanical slave clocks with the following properties 1 Slave Clock indoor outdoor short circuit protected 24VDC alternating impulse output with a current handling capacity of 500mA 2 Tower Clock with 240VAC 3 wire control output using relays for added reliability AVAILABLE TEMPUS VERSIONS Tempus TempusGPS Tempus E Tempus P TEMPUS MENU Time only 1x 24V slave clock and 1x 3 wire tower clock output Time only with built in GPS receiver Time and 2x bell hammer control outputs FET based for direct connection of 2x independent electro mechanical bell hammers This enables hour 1 2 hour and quarter hour strokes the angelus and or simulated single or peal of bells Time and 2x relay programs for school bells lighting etc The Tempus controller provides three menu levels Main display User menu Function Menu The main display provides information about the time and date The user menu allows to set the system variables
4. Size gt 3x 0 75 mm TEMPUS Connection Diagram
5. an back up and restore the Tempus software programs The PIM module consists of a printed circuit board inside a small housing with two 9 pin D connectors on either end The PIM housing is marked with a red and green arrow to indicate the back up or restore directions If the red arrow faces the Tempus the contents of the PIM will be restored to the master clock If the green arrow faces the controller the PIM will make a back up of the Tempus software and program BACK UP THE CONTENTS OF THE TEMPUS 1 Turn the Tempus controller off 2 Insert the PIM into the 9 pin connector on the left hand side of the Tempus with the arrows pointing away from the controller and the green arrow closest to the unit This indicates the contents of the Tempus are being copied RED GREEN x r i ai 0000 JD TEMPUS 3 Turn the Tempus controller on 4 The contents of the controller are now automatically written to the PIM module After a full back up has been made the Tempus screen will return to the main display If a PIM is found to be faulty the Tempus controller will confirm this with the message BAD PIM 5 Before removal of the PIM module turn off the controller Remove the PIM Turn the Tempus back on Store the PIM in a save place for later use TEMPUS 7 Version 1 01 RESTORE THE CONTENTS OF THE PIM 1 Turn the Tempus controller off 2 Insert the PIM into the 9 pin connector on the left hand sid
6. clock synchronisation turning bell hammers on off etc 1 Change time and date Necessary only without a time code receiver 2 Synchronise impulse slave clocks 3 Synchronise tower clocks 4 Turning hammers on off Tempus E 5 Turning relays on off Tempus P D With the down arrow key enter the user menu D GO With the up or down arrow keys select following functions Time Date Tower Clock 3 wire 230VAC Slave Clock 24VDC GO With the right arrow key access the selected function lt a With the left arrow key go back one step without change TEMPUS 4 Version 1 01 TIME Tempus Tempus E and Tempus P Change the time not necessary with a time code receiver Push the down arrow key until Time appears on the display O KS E Push the right arrow key to enter time setting GO Lz SO d Oo The hours flash With the up down arrow keys change the hours Push the right arrow key the minutes flash Change the minutes with the up down arrow keys The time starts by leaving this function pressing the right arrow key The seconds start at 00 If you don t want to change the time leave this function with the left arrow key press 1x or 2x SET DATE Tempus Tempus E and Tempus P Change the date not necessary with a time code receiver Push the down arrow key until Date appears on the display D oe GO Push the right arrow key to enter date setting ZO 15 OCTOBER 08 OO D ZO
7. e of the Tempus with the arrows pointing towards the controller and the red arrow closest to the unit This indicates the contents of the PIM are being restored GREEN RED i e000 JD tempus W Turn the Tempus controller on 4 The contents of the PIM are now automatically loaded into the Tempus After a full restore has been made the Tempus screen will return to the main display If a PIM is found to be faulty the Tempus controller will confirm this with the message BAD PIM 5 Before removal of the PIM module turn off the controller Remove the PIM Turn the Tempus back on Store the PIM in a save place for later use 12 47 36 08 10 Ji tempus TEMPUS 8 Version 1 01 24V DC Impulse output i G Radio Receiver Input LCD Display 12 47 36 08 10 with back lighting Program restore or new program o Programming to Tempora AE Buttons UJ JD tempus Program back up TOWER CLOCKS HAMMERS to PIM Turn off Tempora Install PIM Turn on Tempora Automatic back up or restore Please follow the 240V 50Hz screen Mains Supply b 24VDC TEMPUS 4 Outputs Impulse Output F2 0 8AT slow Tower Clock Tower Clock Movement Minute Impulse Over Voltage Protection 240VAC 50Hz Cable
8. empus on The PIM will automatically reload the program 6 GPS DCF or MSF synchronization If a time code receiver has been installed use following method to check if the Tempus master clock has synchronised to the external time codes If it has synchronised the green light is on Switch the Tempus on and off to check the signal strength This also forces the unit to initialize and read the external time code signal 1 No signal received green LED flashes in synchronisation with the receiver s LED 2 Signal received green LED flashes in alternation with the receiver s LED 3 Synchronisation green LED illuminates continuously The synchronisation takes place during night time at the top minute 00 second between 03 00 and 05 00am provided there is no power failure during this time If the green LED illuminates continuously during daytime it would indicate that synchronisation has taken place the night before If the LED is off during daytime no synchronisation would have taken place or no receiver has been installed Please note the receiver should be installed at least approx 80 150 cm away from the master TEMPUS 3 Version 1 01 B SOFTWARE 1 Main display Turn the TEMPUS master controller on Shortly after turn on the main display will automatically show the current time and numerical date 12 47 36 08 10 2 User menu The user menu allows to set the system variables like time and date slave clocks tower
9. ock will wait SLAVE CLOCK Set or correct the 24V impulse slave clocks For the master to be able to automatically set or correct the impulse clocks it is essential to enter the time as displayed on the clock dials Press the down arrow key until Slave Clock appears in the display W SLAVE CLOCK ZO Enter this function with the right arrow key The output turns off and the impulse clocks stop Take a look at the slave clock faces and enter the time displayed on the dials If there is a discrepancy between slave clock dials correct the displays manually until all clocks are on the same time Then enter the time displayed on all dials o Coar QQ GO The hours flash With the up down arrow keys set the hours to the same hour as displayed on the dials Then push the right arrow key again The minutes flash With the up down arrow keys set the minutes to the same time as displayed by the minute hands on the dials Press the right arrow key to confirm The setting process starts automatically The master compares the just entered dial time with the internal quartz timebase and corrects the slave clocks by sending rapid impulses until the dials are on the right time If the time difference is 40min or less ahead of time the slave clock s will wait TEMPUS 6 Version 1 01 C OPTIONAL PIM MODULE PIM Plug in Memory Module The PIM Programmable plug in memory module acts like a memory stick that c
10. om one controller to another 3 TEMPUS Specifications Supply voltage 230VAC 50 60 Hz 5 10 standard 120VAC 50 60Hz 5 10 on request Outputs 1x 3 wire control output using 2x relays for reliable operation for tower clock movements 1x 24VDC alternating impulse output output capacity 500mA 2x spark free FET outputs for the direct control of bell hammers max output capacity 5A Tempus E only Power Consumption 14W at 230VAC without bell hammers Case Material Polystyrene UL94 VO Dimensions 260 x 160 x 85mm height x width x depth Weight 1 100 kg TEMPUS 2 Version 1 01 Green Synch LED LED flashing Search mode D Gare EK b o E G ush Buttons Synchronisation NY YY ee GZ WF Ga doce ache ce Led steady LED off 4 Front panel 12 47 36 08 10 Display with back lighting and time amp date display No synchronisation or no receiver installed AD TEMPUS 5 Replacing the back up battery The back up battery has a life expectancy of approx 10 years This battery is bundled with the quartz crystal timebase module of the Tempus controller The battery need to be replaced every 7 years before the battery goes flat How best to replace the battery is described below 1 With the optional PIM module take a back up of the Tempus program 2 Turn the unit off and then replace the battery timebase module 3 Insert the PIM unit with the red arrow facing the Tempus 4 Turn the T
Download Pdf Manuals
Related Search