User's Manual EN IMPORTANT
Contents
1. Time set Filter cycle 1 set Filter cycle 2 set 3 6 SET THE MODE 1 Press Mode button to enter mode programming 2 Press Warm button or Cool button to select the mode then press Mode button to confirm the selection STANDARD mode maintains the desired temperature ECONOMY mode the spa only heats the water during the filter cycles SLEEP mode The heater will be turned off all the time SI222 CH USER 8 EN V1 1 User s Manual EN Once the spa has been properly connected the system will automatically select the standard mode to maintain the desired temperature 3 7 LIGHT SEQUENCES 3 1 The LED LIGHT has different modes press the button Light to turn on the light once again to turn off the light press the button again to turn the light and change into another mode 3 8 OTHER FUNCTIONS Filter cycle programming Under the standby mode the filter cycle programming will automatically run twice each day Hose and pipe clearing cycle One minute after the filtration cycle has started the system will automatically turn on the blower and the massage pump for 2 minutes to purge the hydraulic circuits Clean up cycle Optional depending on the configuration At the end of any massage after 30 minutes a clean up cycle will begin the filtration and ozone generator will run for one hour If all the buttons are left on the system will revert to standby mode after one hour Massage automatical2. S1222 CH USER 5 EN V1 1 User s Manual EN 2 4 AVOIDING RISKS OF HYPERTHERMIA e Prolonged direct contact with hot water could cause HYPERTHERMIA This occurs when the internal body temperature reaches levels above the normal temperature of 36 5 C It is advised not to bathe for longer than 15 minutes e Symptoms of hyperthermia are a sudden drop in blood pressure resulting in a sensation of dizziness with the possibility of fainting e The Spa water should never be above 40 C e Water temperatures between 37 C and 40 C are only considered safe for adults without any health problems Lower temperatures are recommended for the majority of people and children THE USE OF ALCOHOL DRUGS OR MEDICINES COULD INCREASE THE RISK OF HYPERTHERMIA IT IS NOT ADVISABLE FOR PREGNANT WOMEN PATIENTS WITH HIGH BLOOD PRESSURE A HEART CONDITION DIABETES OR UNDER MEDICATION TO USE THE SPA SHOULD SEEK DOCTOR S ADVICE SEEK DOCTOR S ADVICE IMPORTANT Your Spa is designed for private use and discontinued operation It is recommended not to exceed two 15 minute massage sessions per day S1222 CH USER 6 EN V1 1 User s Manual EN 3 USE OF THE SPA 3 1 SPA CONTROL PANEL Jets 2 omer Standard 1 Sleep Time a chet 1 a Ferd L 30 we k y 23 Blower 3 2 FUNCTION BUTTONS JE T E Power on stand by Switching key Jets1 Time CE OE Soe Pump 2 Temperature time mode set key rn eee Bo Air blo
3. 3 Power on press power button to turn on the power once the panel is turned on all the functions are available 3 4 SETTING THE TEMPERATURE 10 40 C 1 Press the Warm button Each time the button is pressed the set Temperature display will increase by one degree 2 Press the Cool button Each time the button is pressed the set Temperature display will decrease by one degree 3 5 SET THE TIME AND THE FILTERING CYCLE 1 To set the time press the Time button then the Mode button 2 Select the hour by pressing Warm or Cool button each press will change the time by one hour Press Mode button to enter the minutes press Warm or Cool button to change the minutes Press Mode button to exit the time setting procedure To set the filter cycle press Time button and Mode Mode Mode Within 3 seconds press Warm button or Cool button to adjust any time Start time hour and minutes for the start time of filter cycle 1 Press the Mode button to set the end time of filter cycle1 adjust the time as above Press the Mode button to set the start time of filter cycle 2 adjust the Time as above Press the Mode button to set the end time of filter cycle 2 adjust the time as above Standard Time Standa rd Slander o a T 7 o T Ea Do A r E 6 I Lo 0 Oo LI Piter Io COLI LD Frez G o ga z
4. avoid possible reactions Do not add chemical products to the water if there is someone in the Spa 5 2 MAINTENANCE SCHEDULE OF THE SPA WATER All chemical products Bromine in tablet form Algaecides Anti calcareous and pH reducer must be added to a floating dispenser not supplied with the massage pump on for at least ten minutes S1222 CH USER 18 EN V1 1 User s Manual EN 5 3 pH ADJUSTMENT A pH index of between 7 2 and 7 6 is recommended The pH level measures the acidity and alkalinity Values above 7 are alkali and below 7 are acid It is very important to maintain the correct pH level both for the disinfectant to work properly and to prevent corrosion or deposits on the Spa Any damage caused by an inadequate pH level is not covered by your Spa guarantee e The effects of a very low pH level are The disinfectant will quickly dissipate The equipment of the Spa become rusty The water can start causing skin irritations to bathers e The effects of a very high pH level are The disinfectant is less effective Scale may appear on the acrylic and equipment The water may become cloudy The filter cartridge can become blocked Check the pH of the Spa water daily using the pH test set not supplied If the pH is above the indexes use pH MINOR SPA Wait for two hours and re do the pH test If the pH is below indexes use pH MAJOR SPA Wait for two hours and re do the pH test Once t
5. the Spa To use this product it is recommended to empty the Spa and apply a degreaser with a sponge on the parts to be cleaned Rinse immediately with plenty of water 5 6 OZONE GENERATOR only in spas with this option Ozone O3 is an oxidizing chemical compound which is very effective for disinfecting water The main advantage of ozone is that it leaves no chemical trace and is odourless The capacity of ozone as a disinfectant is due to its potential as an oxidizing agent which eliminates any organic matter that may be present in the water In order to produce ozone electricity is passed through an ozonator to produce ozone ions from oxygen in the atmosphere This is an automatic process and the resulting product is injected through the jets of the Spa The process does not require the user to use any other mechanism The water is collected in the drains and skimmer by the absorption action of the massage pump It is then sent through the heat exchanger and as it leaves the ozone is injected The water is distributed by the filtering back flow Part of this flow is also distributed through the drain outlet in order to avoid stagnant water from collecting Ozone treatment does not exclude the use of other chemical products such as Bromide or Chlorine Ozone is considered a complementary process to them therefore reducing the use of Bromide or Chlorine S1222 CH USER 20 EN V1 1 User s Manual EN QUICK GUIDE TO THE APPLI
6. 1 EN V1 1 User s Manual EN 1 GENERAL DETAILS This manual contains all the information needed to fully enjoy your SPA Please read carefully all the instructions provided as well as the installation manual that you will find with this user manual If you have any question or doubt on the operation or maintenance of this product please contact your local dealer They are professional specialists and their knowledge will help you enjoy this product Keep this manual in a safe place as you will find it very useful IMPORTANT The manufacturer reserves the right to modify part of the design or specifications without prior notice and without entering into any obligation This Spa has been designed and conceived for private use only any public use shall annul its guarantee S1222 CH USER 2 EN V1 1 User s Manual EN 2 SAFETY WARNINGS 2 1 GENERAL Avoid contact with electrical voltage Carefully follow current regulations regarding accident prevention Any modification on the equipment requires prior authorisation from the manufacturer Original spare parts and accessories authorised by the manufacturer guarantee greater safety The manufacturer of the equipment is exempt from all liability for damages caused by using non authorised Spare parts or accessories The user shall ensure that qualified adult professionals carry out both the assembly and maintenance works who have previously carefully read the installation a
7. CATION OF CHEMICAL PRODUCTS Reason for Use Amounts per m Frequency of use of water pH MINOR SPA Add if the pH level is above acceptable levels 7 2 7 6 ppm pH MAJOR SPA Add if the pH level is below acceptable levels 7 2 7 6 ppm BROMIDE Add if the Br level is TABLETS above acceptable values 3 5 ppm ANTI CALCAREOUS To prevent precipitation of calcium salts scale SPA ALGAECIDE Prevents algae from growing in the water DEGREASER To eliminate rings of dirt on the walls of the Spa ANTIFOAM Foam in the water 6 RECYCLING AND THE ENVIRONMENT j gt N Add following recommendations of the chemical product manufacturer Add following recommendations of the chemical product manufacturer Add following recommendations of the chemical product manufacturer Add following recommendations of the chemical product manufacturer Add following recommendations of the chemical products manufacturer Rub with a sponge and immediately rinse with abundant water Add following recommendations of the chemical product manufacturer Analyse the pH daily with the pH Test Analyse the pH daily with the pH Test Analyse the Br daily with the Br Test Once a week and whenever the water is renewed Once a week and whenever the water is renewed Whenever dirt is observed on the walls of the Spa Whenever foam appears in the water A The Spa includes
8. User s Manual EN CONTENTS te Generali IDECAINS aeea a bee el a a ent ee taeda meres 2 2 Savery W AmI Seea Madina eau ea aadee E 3 2 1 General 2 2 Warnings in maintenance work 2 3 Warnings in the use of the Spa 2 4 Avoiding risks of hyperthermia 5 USE Ol TNS SP avi iiy nE A A E E NT 7 3 1 Spa Control Panel 3 2 Function buttons 3 3 Initial start up 3 4 Set the Temperature 3 5 Set the Time and the Filtering Cycle 3 6 Set the Mode 3 7 Light sequences 3 8 Other options 3 9 Jets operation 4 Maintenance Instructions of the Spa ccccc ee ee eee eeeseeeneeeeeesecuennnaeeenegs 11 4 1 Renewing the Spa Water 4 2 Maintenance of the Filter 4 3 Maintenance of the Acrylic 4 4 Maintenance of the Unit 4 5 Maintenance of the Light 4 6 Maintenance in Periods of non use or absence 5 Maintenance oF The Water einn a a tebe A 18 5 1 Safety in the use Chemical Products Maintenance Schedule of the Spa Water pH Adjustment Disinfection of the Water Use of Special Products Ozone Generator OUI BR WN 5 F oe S i 6 Recycling and the EnNvirOnMent cccceceecsccssneeeeeetecennenereseceeennaseneses 21 IMPORTANT This instructions manual contains fundamental information on the safety measures to be adopted when installing and starting up the spa It is therefore essential that both the Fitter and the User read these instructions before assembly and start up S1222 CH USER
9. anybody to play with sharp or metal objects inside the Spa which could damage the acrylic surface e Do not allow any user to access the electrical parts of the Spa e Do not start up the Spa unless it is full of water e Do not use electrical or electronical apparatus inside the Spa e Do not let animals in the Spa e Do not fill the Spa with other liquid other than fresh duly treated water e Do not fill the Spa with hot water maximum 35 C let the water heat by itself otherwise it could damage the temperature probes see Temperature Adjustment e Do not use the Spa immediately after intense physical exercise e Do not use the Spa if you are suffering from a contagious disease or 14 days after recovering from a contagious disease S1222 CH USER 4 EN V1 1 User s Manual EN e In order to guarantee maximum safety when bathing all our Spas use pumps designed to suction water from anti vortex safety drain covers located on the floor of the Spa Take special care that these drain covers are not covered by any object or the users pieces of clothing hair legs etc For safety reasons your head should always be outside the Spa in order to avoid drowning Do not use the Spa if the drain covers are broken damaged or unassembled as apart from damaging the Spa it could also lead to a risk of drowning e The headrests of your Spa are made of synthetic foam which can be damaged in high concentrations or bromine or chlori
10. electric and or electronic material which at the end of its life span should be suitably treated as special waste Contact your local authorities to find out the collection and waste disposal procedure for electric and electronic material S1222 CH USER 21 EN V1 1
11. em if dirt is observed Remember that if a filter is blocked it will reduce the water flow and therefore the Spa will operate incorrectly PRE FILTER It is based on a grid where the larger particles floating on the water are deposited 0 FILTERING CARTRIDGE Retains the smaller particles S1222 CH USER 11 EN V1 1 User s Manual EN To change or clean the filter follow these instructions 1 Disconnect the electrical supply Differential in the OFF position 2 Locate the filter and remove it as shown 3 Lift the skimmer cover Remove the pre filter upwards together with the filtering cartridge To reach the pre filter and the filtering cartridge in Spa models with side skimmers follow the steps indicated below 1 Carefully slide off the trim of the skimmer unit upwards 2 Remove the tray that is used as a pre filter 0 3 Remove the filtering cartridges one by one by unscrewing and lifting them out of their housing and placing them in a horizontal position 4 Clean the pre filter with water until there are no remaining particles Clean the filtering cartridge with a garden hose jet spray at low pressure until it is clean Clean from top to bottom spraying the water at an angle of 45 5 After several washing cycles it may be necessary to change the filtering cartridge Contact your supplier 6 Replace the filtering cartridge and pre filter S1222 CH USER 12 EN V1 1 U
12. he pH index has been adjusted to the values indicated above proceed to the next point 5 4 DISINFECTION OF THE WATER Disinfection of the water is of utmost importance in order to destroy algae bacteria and organisms that could develop in the water However excessive disinfection could cause skin and eye irritation BROMIDE TABLETS are a Suitable disinfectant for the Spa water This product is placed in the pre filter and gradually dissolves Check the residual bromide level daily using the Br analyser set The recommended level of residual bromide is between 2 2 and 3 3 ppm S1222 CH USER 19 EN V1 1 User s Manual EN 5 5 USE OF SPECIAL PRODUCTS Apart from products to maintain the pH and disinfectant level there are other products formulated especially for use in Spas that will help you to maintain the water and installation in perfect condition e SPA ANTI CALCAREOUS This prevents the precipitation of calcium salts scale particularly in hard water This product should be added weekly and whenever the water is renewed e SPA ALGAECIDE This algaecide prevents algae from growing in the Spa water This product is added weekly and whenever the water is renewed e SPA ANTIFOAM Foam is often formed owing to the agitation of the water and grease present in the water Whenever there is a significant amount of foam remove it with Spa Antifoam e SPA DEGREASER To remove rings of dirt and grease that form on the walls of
13. ions in each country should be followed There is a risk of flooding with this equipment and therefore the Spa should be installed in an area prepared to collect or drain leaking water either from below or overflowing water as a result of using the Spa or from possible leakage in any of its circuits See the Guarantee The installation of the Spa must at all times meet current regulations applicable in each country particularly those referring to electrical safety This unit must be installed in an appropriately prepared area with easy access to all the components of the Spa The Guarantee does not cover any S1222 CH USER 3 EN V1 1 User s Manual EN building work required to position or replace the product See the Guarantee IMPORTANT The manufacturer shall not be held responsible for any damage as a result of incorrect positioning or misuse of the Spa 2 2 WARNINGS ON MAINTENANCE WORK e Before carrying out any electrical or mechanical maintenance work make sure that the machine is disconnected from the mains and that the start up devices are blocked e Do not handle the equipment with wet feet 2 3 WARNINGS ON THE USE OF THE SPA e Take extreme precautions to stop children from entering the Spa unattended To avoid accidents ensure that children are supervised at all times Never leave children alone in the Spa Take care when entering and leaving the Spa to avoid slipping on wet surfaces e Do not allow
14. ly turns off If left on the Jest1 Jets2 and Blower will automatically turn off after 15 30 minutes Memory function The system will revert to the last setting after each power on Diagnosis functions See the installation manual for more detailed instructions Default settings Temperature 38 C Mode Standard Filter cycles Filter 1 08 00 gt 10 00 Filter 2 20 00 gt 22 00 RISK OF ELECTRIC DISCHARGE The user must not repair any parts Do not attempt to repair this control Call your dealer or technical service S1222 CH USER 9 EN V1 1 User s Manual EN 3 9 JETS OPERATION The water jets provide a hydrotherapy pressure jet It is a closed circuit where the water is absorbed by 1 2 or 3 pumps depending on the SPA model through the drain and driven to the jets The hydromassage effect is provided by the jet when the circuit water mixes with the outside air in the so called Venturi effect To adjust the amount of air driven into the jets simply turn the air input tab venturis as follows Turn clockwise to reduce the amount of air mixed in the jets This will reduce the intensity of the jet massage Turn anti clockwise to increase the amount of air mixed in the jets This will increase the intensity of the jet massage LEX GREATER INTENSITY LESS INTENSITY Each air inlet activates a certain group of jets Some jets can also adjust the flow intensity on opening and closing the wate
15. nd service instructions ATTENTION Correct earthing connection is essential The earth connection circuit of the building must be in perfect condition to guarantee the safety of the Spa user If you have doubts on the matter ensure the earth circuit is reviewed by qualified personnel The manufacturer shall not be responsible for the damages caused by inadequate maintenance of the earth connection circuit ATTENTION It is essential that the owner of the Spa tests the differential switch at least once a month to check its good working order The manufacturer shall not be responsible for the damages caused by the assembly of non authorized accessories nor for those caused by a improper handling by non qualified personnel Please contact your authorised dealer or technical assistance service if you have any doubts or need technical assistance During operation some parts of the equipment are at dangerous electrical voltage levels Work on each element or equipment can only be performed once it has been disconnected from the mains and with the start up devices disconnected Safety in the operation of the machine can only be guaranteed if installation and service instructions are followed The limits indicated on the electrical control panel cannot be exceeded under any circumstances Contact the Technical Service of the manufacturer or your local dealer in the event of malfunction or a breakdown In this respect the current regulat
16. ne or low levels of pH Make sure that when adding chemical products the headrests are neither totally nor partially immersed in the water If necessary remove them until the chemical products have taken effect Damages resulting from improper use shall not be considered under the guarantee of the product e The Spa includes a cover designed to protect the acrylic surface from sunrays when it is not being used This cover will also help to keep the water warm and for sun protection that could damage the acrylic material of the Spa The cover will require additional means of protection in the event of heavy rain or snow The cover is not designed to bear heavy weights not even children or animals Also water in bad condition could damage the cover Therefore keep the chemical levels in accordance with the instructions provided in this manual Do not clean the cover with detergent or abrasive products as they will cause damage Improper use of the cover is not included in the guarantee WARNING The water should be disinfected thoroughly before using the Spa especially if it has not been used for a certain period of time whether or not it has been left with or without water inside During periods of non use traces of stagnant water may remain which may cause the growth of micro organisms potentially dangerous for health Therefore disinfect the Spa as indicated in this manual ensuring that the pH and disinfectant parameters are suitable
17. ormal for small cracks to appear This is a normal reaction to environmental conditions that do not damage the wood It should simply be polished and treated with oil Good quality Teak oil should be used or any other wood protection oil 4 5 MAINTENANCE OF THE LIGHT Replacing the lamp is the only required maintenance on the spotlight To replace the lamp follow these steps WARNING RISK OF ELECTRIC SHOCK Make sure the power of the Spa is turned off The new lamp must have the same features as the lamp supplied Never install lamps without the front lens To ensure perfect watertightness clean the mounting base of the flat gasket of the glass or replace it if you observe any dents or permanent damage Depending on spotlight model the lamp is replaced in the following way Draining the Spa depending on the model of spotlight e Empty the Spa See section Spa Drainage e Fit the aforementioned plastic spanner in the front side of the spotlight and turn it in order to release its bayonet fastening e Change the lamp press fastening e Reassemble the spotlight making sure to fasten the bayonet of the front part with the spanner and pressing sufficiently to prevent water from entering the spotlight e Assemble the trim of the spotlight in the colour you wish Without draining the Spa depending on the model of spotlight e Dismantle the wooden side panel where the spotlight is installed using a medium
18. r flow To do this proceed as follows Turn the outer ring a quarter clockwise to close the jet Turn the outer ring a quarter anti clockwise to open the jet ATTENTION Do not attempt to forcibly turn the outer ring of the jet as you could damage it S1222 CH USER 10 EN V1 1 User s Manual EN 4 MAINTENANCE INSTRUCTIONS OF THE SPA The Spas are built with maximum quality and with the hardest wearing materials available Proper care and maintenance will ensure a long life span of the Spa and its components 4 1 RENEWING THE SPA WATER To change the Spa water e Disconnect the electrical equipment placing the differential switch installed in the main input of the home in the OFF position e Locate the drain valve see Spa drainage of the Installation Manual and turn the valve to the OPEN position The Spa will empty by gravity through the general drain e Once the Spa is empty inspect the acrylic and clean if necessary see point 4 3 Maintenance of the acrylic Turn the drain valve to the CLOSED position e Fill the Spa with clean water see Filling the Spa of the Installation Manual 4 2 MAINTENANCE OF THE FILTER All Spas include either a cartridge filter or a pressure filter Check the type of filter in your Spa and follow the maintenance instructions below 4 2 1 MAINTENANCE OF CARTRIDGE FILTERS It is advisable to periodically check the condition of the cartridge filter Clean them or replace th
19. ser s Manual EN 7 Turn on the electrical equipment Differential in the ON position The Spa should always operate with the pre filter and the filtering cartridge in the correct position Never place objects that could block the inlet to the filter 4 2 2 MAINTENANCE OF THE PRESSURE CARTRIDGE FILTER It is advisable to periodically check the condition of the cartridge filter Clean them or substitute them if dirt is observed Remember that if a filter is blocked it will reduce the water flow and therefore the Spa will operate incorrectly These filters are made up of a single part To replace or clean the filter follow these steps 1 Turn the electric unit off Differential in the OFF position 2 Locate the filter and remove it as follows 3 Unscrew the bleeding drain marked with an arrow to remove the air This step is very important 4 Lift the part blocking the filter see figure and unscrew the part fastening the unit anticlockwise S1222 CH USER 13 EN V1 1 User s Manual EN 5 Lift the remaining part by the handle to reach the cartridge filter 6 Clean the pre filter with water until no particles remain Clean the filtering cartridge with a low pressure garden hose until it is clean Clean from top to bottom spraying the water at a 45 angle 7 After several cleaning cycles you may have to replace the filtering cartridge To do this please contact your supplier 8 Reinsert
20. sized stecker screwdriver S1222 CH USER 16 EN V1 1 User s Manual EN e To replace the lamp turn the lamp holder bushing anticlockwise and lift it from its position e Once the faulty lamp has been replaced place the lamp holder back in position and reassemble the wooden side panel of the Spa e If you have any doubt about the explanation of this operation contact your authorised dealer or authorised technical service 4 6 MAINTENANCE IN PERIODS OF NON USE OR ABSENCE SHORT PERIODS 3 5 DAYS e Adjust the pH and treat the water see Water Maintenance section e Cover the spa e Before using the Spa again readjust the pH and treat the water again PROLONGED PERIODS 5 14 DAYS e Set the temperature at its lowest level e Adjust the pH and treat the water see Water Maintenance section e Cover the Spa e Before using the Spa again reset the temperature as required readjust the pH and treat the water again PREPARATION FOR WINTER If it is not planned to use the Spa through the winter season or for prolonged periods of time the following operations should be done e Disconnect the electrical equipment placing the differential switch tab in the OFF position e Locate the drain valve see Drainage of the Spa and turn the red lever of the valve to the OPEN position The Spa will empty by gravity through the general drain e Leave the drain valve open e Remove the filter cartridge s from the filter See Main
21. tenance of the filter and keep in a dry place e Clean and dry the Spa e Cover the Spa Do not leave water in the Spa without electrical connection outdoors at temperatures below 4 C as the pipes can freeze and damage the Spa S1222 CH USER 17 EN V1 1 User s Manual EN 5 MAINTENANCE OF THE WATER The user must pay particular attention to the maintenance of water Maintenance will depend on the mineral content of the water used how often the Spa is used and how many people use the Spa There are three essential points for the maintenance of the water QO FILTERING OF WATER O CHEMICAL ANALYSIS AND pH CONTROL QO DISINFECTION OF WATER 5 1 SAFETY IN THE USE OF CHEMICAL PRODUCTS Before using a chemical product read the instructions on the product label carefully IMPORTANT It is advisable that always the same person handles the chemical products Keep these products away from children Add the exact amounts to the water as specified Keep containers tightly closed in dry well ventilated places Do not inhale chemical products and take care not to let them come into contact with the eyes nose or mouth Wash hands after use Follow the emergency instructions on the product label in the event of an accident or ingestion Do not smoke while handling these products they may be flammable Do not store these products inside the Spa unit Do not mix products Add first one and then the other to the water to
22. the filtering cartridge the press on cover and the threaded part It is very important to lift the part you have previously lifted in point 4 and insert it properly in the corresponding slot of the filter S1222 CH USER 14 EN V1 1 User s Manual EN 9 Close the valve you opened in point 1 Always remember to check that this valve is closed properly otherwise your spa could be seriously damaged 10 Turn the electric unit on Differential in the ON position Never place objects that could block the inlet to the filter Remember to follow all the steps and to close the valve as indicated in order not to damage the Spa or hurt yourself 4 3 MAINTENANCE OF THE ACRYLIC To clean the acrylic surface use a non abrasive cleaner and warm water Once the Spa is clean rinse with water to remove the detergent Clean the non submerged part of the spa with good quality Spa polish once a week Remember never leave the Spa uncovered and exposed to sunlight as this could cause damage not covered by the guarantee 4 4 MAINTENANCE OF THE UNIT Only Spas with natural wood unit The unit is treated with special oil that protects the wood from water absorption It is recommended to repeat this treatment periodically at least once a year Extra treatment given to the unit when it is new will prolong its life span S1222 CH USER 15 EN V1 1 User s Manual EN In time the wood will darken and because it is live matter it is n
23. wer Temperature time mode set key oo Operating instructions 1 Power this button is used to switch between stand by and power on modes 2 Jeti press the jet button to activate the low speed of the pump and again for the high speed of the pump optional depending on the spa model press the jet button again to turn off the pump 3 Jet2 Press the jet button to turn the pump 2 on or off Optional depending on the spa model 4 Blower press the blower button to turn the blower on or off Optional depending on the spa model 5 Light press the light button to turn the light on or off and switch between different modes 6 Warm Temperature time mode set key 7 Cool Temperature time mode set key 8 Mode allows to switch between STANDARD ECONOMY and SLEEP modes 9 Time time 10 Time Warm Press together time and temperature it will indicate reversely Press again and it will return back 11 Warm Cool Press them together to lock the panel indicating PL Press them again to unlock 12 Time Blower Press them together to return to original set S1222 CH USER 7 EN V1 1 3 3 INITIAL START UP 3 3 1 Stand By Power On mois gag i ry O 3 A E oF Stand by Power on 1 Stand by the spa goes into stand by mode when the spa is properly supplied with power 2 In the stand by mode the current temperature and time will appear on the screen
Download Pdf Manuals
Related Search