Home
ETM770 Signal Strength Meter User Manual Features:
Contents
1. 2049 lt CR gt Both IP1 and IP2 must ET IP2 144 132 166 189 2049 lt CR gt be set Checking IP Connectivity Use the UP and DOWN buttons to select 2 ISP Connect and press ENTER Open ISP confirms that the SIM and ISP login details are correct and that a successful logon occurs Possible errors may come from incorrect authentication details incorrectly configured SIM or no signal Ping confirms that once logged on to the ISP a remote server can be reached Once ISP testing is finished use the UP and DOWN buttons to scroll to Return gt Main Menu and press ENTER ETM 770 Users Manual 201404RV01 Docx Page 8 of 16 For Support Contact 61 2 9956 7377 Or support etmpacific com au Main Menu 3 Network Operators Signal strength and cell information for available networks can be scanned from a SIM of any valid network operator Note that registration on the network and ISP connectivity testing see above is only applicable for the network which provided the SIM Scanning a Different Network To scan the signal from a different network at the Main Menu use the UP and DOWN buttons to select 3 Net Operators Then once the screen below is shown use the UP and DOWN buttons to select the desired Network to be scanned Once the desired network is selected by pressing ENTER the unit will wait for a response from the network and then return to the main menu Once back at the main menu 1 Scan Signal can be selected and th
2. Code Identifies a Location Area e Cell ID Cell identification number APN ACCESS Point Name Refer to Network Operator C IP IP Address allocated by Network Operator RSCP Received Signal Code Power Received Signal Code Power in dBm SQ Signal Quality Quality value for base station selection in dB RX level value for base station selection in dB ETM770 Users Manual 201404RV01 Docx Page 4 of 16 For Support Contact 61 2 9956 7377 Or support etmpacific com au Introduction Nomenclature ETM770 1 incorporates the Cinterion TC63i engine and is intended for use worldwide The ETM770 2 770 3 variants incorporate the Cinterion EU3 P PH8 P engine both models are intended for use in Europe Asia Australia and New Zealand Overview The ETM 770 x models are signal strength meters designed for measuring the signal strength of 2G and 3G cellular operators at a particular location Terminal Nomenclature History Comment Module Installed ETM770 1 First Release TC63i ETM 70 2 First Release EU3 P ETM 70 3 First Release PH8 P Applications The product is typically used to z Check signal availability for a potential installation r Determine the best operator for a particular location y Assess antenna positioning and suitability for a particular installation Interfaces Min USE The Mini USB located on the top left of the unit is used both for programming the unit using a terminal program ae as well as for charging
3. ETM770 Users Manual 201404RV01 docx l j ETM770 1 2G GSM GPRS Signal Strength Meter ETM770 2 3G 2G HSDPA UMTS GSM GPRS Signal Strength Meter ETM770 3 3G 2G HSPA UMTS GSM GPRS Signal Strength Meter ETMZ770 Signal Strength Meter User Manual Features LCD Display with backlight Scan for signal strength r Identify network operators SMA antenna connector FME adapter included r Internal rechargeable battery pack Mini USB connector for programming and recharging r Send TCP IP data packages to a server to confirm connectivity Page 2 of 16 For Support Contact 61 2 9956 7377 Or support etmpacific com au Contents Explanatory List of Network Abbreviations cccccccceeccceeceeeeceeeceeeeseeeeseeeseeeeseeeseeeeeeeeseeeaneesaeeees 3 OGU CHON seenen AE EE E AE A E E N 4 NOMNI O oa er E AE ET E 4 OVENI W a E A E T tea weactitera egacasn ener caine 4 PAO ONG ANON erreien ineen EEEE A EEE EE E EEEE E AEE EEN E EE E 4 DR ch E e E E E E E E A AA EA A E E E E santos 4 LLR D S o E E A E E E E EA S E A E E E EA 4 SMA Antenna COnne tol cccccccecccseccceeeceeeceeeecneesececeeeesaeeseeeseuseseessaeeseeessueesaeeseueesaeeseeeeasoeees 4 BNO LO meren E sine aa sie teere chia E E E in dentonansniadas eesaecn a eae 4 POOT scene ecto apceeta tn we oe vec nin ceva gdp eee pete psn ga E as E 4 Charging Temperature Limitation ccccccccecccescecececeeeeeeeeseeeeseesaneceuceseeeeeaeeseee
4. IP1 213 115 2 218 3004 RIP2 213 115 2 218 3004 Last TCP 213 115 2 218 3004 LP 2040 Last UDP 213 115 2 218 2049 LP 2040 OK ET IAPN1 Sets APN Access Point Name OK cgdcont 1 ip telstra internet for network operator and SIM ET IAPN2 used cgdcont 1 ip telstra internet Must set both APN1 and APN2 Note the unit must be reset for this command to take effect ET IP1 144 132 166 189 2049 Sets the remote IP address ET IP2 144 132 166 189 2049 Must set both IP2 and IP Note the unit must be reset for this command to take effect Software Reset Note If you are using SIMs that are on a VPN then a username and password are required to be set this can only be done via the appropriate ETM configuration tool contact ETM for assistance ETM770 Users Manual 201404RV01 Docx Page 15 of 16 For Support Contact 61 2 9956 7377 Or support etmpacific com au Troubleshooting Error Net Login on Startup Possible Causes Further Details Corrective Action SIM PIN Incorrect The Scan Signal Section can be Accessed Deactivate SIM Pin in but will show handset recommended Use Configuration tool to enter SIM PIN contact ETM for assistance No or very weak signal If SIM PIN okay the following start up Check antenna connection screen would have been displayed Try alternate antenna Check network coverage maps information Check Radio Band region or Radio Band Settings lf ETM770 2 consider trying an alter
5. Program available free of charge upon request can be used to set certain parameters in the unit Baud Rate is set to 9600 N 1 Terminal COM11 ETM M TTEKNIK AB 08 252875 eettil ID Default ETM O RTC 10 06 068 22 068 55 REFDATE 2010 06 06 53 TOTAL 22 41 12 RSTIN 1 16 47 RC Si 794 PU 3860 T2BO034R04 20100805 CTo408 F Hil 65535 255 N a SIGNAL 10 MIN 0 MAx 10 SUPPL OLT 5 02 ACT 3G CHANN 10737 RS 0 dBm 91 LAC 7DO9 CELL 41E1666 MTemp 2 deqC CID 0 IMET 359520030001667 BAT VOLT 4 21V DE AT C50 050 10 99 OF Port Ring MICO E CSA ECTS Par ero 3600 id aa F r aTa csa ATi ATDL ath o Jani ETS mice CREG ATov CPIN ATA Add AddA Hist Clear adw Mr Screen Shot of ETI command response using ETM Term42 program ETM770 Users Manual 201404RV01 Docx Page 14 of 16 For Support Contact 61 2 9956 7377 Or support etmpacific com au Some Gommon Usetul Commands to Use with Terminal Window Command Typical Response ETI To gain a quick summary of the See above example units status as well as information on units firmware version ETSEND AT COPS To determine network amp service COPS 1 0 Telstra 32 Mobile to which you are connected ET I amp IP To check set server settings et I amp ip AT CGDCONT AT CGDCONT CGDCONT 1 IP internet 0 0 0 0 0 0 OK IP STATUS IPCL TCP APN internet LIP 0 0 0 0 R
6. Temperature Limitation In the battery charge condition of the ETM770 when the mini auton S l Risk of explosion if battery is USB connector is used the maximum operating ambient replaced by an incorrect type temperature is limited to 40 C Dispose of used batteries appropriately Starting the Unit After ensuring the unit is off insert a suitable SIM card and connect your antenna of choice We recommend that the SIM PIN if applicable is deactivated before inserting in the unit If the unit has sufficient charge then depressing the Enter button will start the unit After the unit has successfully started the following screen should appear ETM770 Users Manual 201404RV01 Docx Page 6 of 16 For Support Contact 61 2 9956 7377 Or support etmpacific com au Main Menu Scan Signal Scanning for Signal Strength Use the UP and DOWN buttons to select 1 Scan Siqnal and then press ENTER Battery Indicator indicates charging Signal Strength Network 2G or 3G Frequency Y indicates USB connected R indicates home network I indicates ISP connected Scanned Network Signal Strength in dBm and SQ value between 1 and 31 plus Average SQ during current scan Signal strength bar Min and Max Signal Strength during current scan LAC Cell ID PLMN and Channel ID The above Scan Screen Indicates the Network Frequency and Signal Strength Minimum Maximum and Average during the period which the scan has
7. been active to start a new scan press any button and you will return to the main menu then select 1 Scan Signal again To scan another network see Main Menu 3 Network Operators Last Scan option will show results of the last scan that was performed Neighbour Cells This This option will indicate how many cells are available Main Menu 2 ISP Connect This function allows for checking an IP connection using the selected network and SIM To use this feature you must first set up the details of the server to be connected The appropriate commands can be sent from a terminal program or via SMS If user name are required then these can only be set via appropriate Configuration Tool contact ETM for more details ETM770 Users Manual 201404RV01 Docx Page 7 of 16 For Support Contact 61 2 9956 7377 Or support etmpacific com au Set APN Access Point Name The following commands should be used to set the APN for connection to an ISP over Internet ET IAPNx cgdcont 1 ip APN lt CR gt Example ET IAPN1 cgdcont 1 ip telstra internet lt CR gt Both APN1 and APN2 ET IAPN2 cgdcont 1 ip telstra internet lt CR gt must be set Set IP Address The following commands should be used to set the IP Address for connection to a Server ET IP1 Remote Server IP Address Remote Port lt CR gt ET IP2 Remote Server IP Address Remote Port lt CR gt Example ET IP1 144 132 166 189
8. e signal strength on the new network scanned as required ETM770 Users Manual 201404RV01 Docx Page 9 of 16 For Support Contact 61 2 9956 7377 Or support etmpacific com au Main Menu 4 Status The Status section provides additional information on the current network connection as well as details of the unit s battery status and firmware version Press the UP and DOWN buttons to select 4 Status and press ENTER to access the unit status details system Details Unit details including firmware version hardware version IMEI supply and battery voltage Scroll down until Return appears and press Enter to return to previous menu ETM770 Users Manual 201404RV01 Docx Page 10 of 16 For Support Contact 61 2 9956 7377 Or support etmpacific com au Network Select Network Information such as cell details relating to the network to which the unit is set will be displayed Scroll down until Return appears and press Enter to return to previous menu Settings Select Settings Details of the IP address and Port to which the unit has been set see Main Menu 2 ISP Connect will be displayed Scroll down until Return appears and press Enter to return to previous menu ETM770 Users Manual 201404RV01 Docx Page 11 of 16 For Support Contact 61 2 9956 7377 Or support etmpacific com au Main Menu 3 Services The Services menu section allows you to change Radio Band Region and Radio Band as well as Shutdown and Resta
9. era E ps pe eon acdsee ecards den ania leanne neeaaa nedeee ened ainda ananassae 12 SEA CIC occ ciee sis wsisrimsistewananravigatsronte E E A 13 Using a Terminal Window to Configure the Unit 0 0 0 0 ccc ccccceececeeceeeeseeeeeeeeseeeeseeeseeesseeeseeeaees 13 Some Common Useful Commands to Use with Terminal Wind OW c sssseccceecesssecceeeeeseceeessaaeseeess 14 TOUDE SIO ORIG ccs casts annctsniosenncetocetee E sere wee Unc union ese mnsiesnce ais amine ben iopncntaasnet oes 15 Error Net Login ON Startup 0 2 0 ccc ceccceececeecceeecceeceeeeeseeeeeeeeseeeseeeeeeeeseueeseeeseeeeseeeseeeesuseseeesaeseeaes 15 OPR COMEC aoe ke ee ee ee eee eee ee eee ee ee 15 ETM770 Users Manual 201404RV01 Docx Page 3 of 16 For Support Contact 61 2 9956 7377 Or support etmpacific com au Explanatory List of Network Abbreviations Abbreviation Full Name Explanation CHANN Channel Shows the ARFCN Absolute Frequency Channel Number of the Radio Band Frequency Primary Synchronization Code Describes start and stop time for the time slot that the device has been allocated PLMN Public Land Mobile Network A network that is established and operated by an administration or by a recognized operating agency ROA for the specific purpose of providing land mobile telecommunications services to the public Mcc Mobile Country Code The first part of the PLMN code i Mobile Network Code The second part of the PLMN code LAC Local Area
10. esaeesauesseseseeesauseeaes 5 SAAE U ea EE EE 5 Man Menu s T Scan o IN er a E a A E E a 6 scanning Toroignal Stengt seneese niei E a aE R 6 Ee EEE i E ENA E A EE E A A AE A E A A E A A nee buasiovaee 6 CTO IDOI GOIS stone ca onr E E E cee 6 Main Menu 2 ISP COnne ct ccc cccccccccccecceeeeeeeeece cece ceseeeeeeesaeesaaeeseeeseusesaeesseeesaeeseueeseessueeeseeees 6 Set APN Access Point NAme cccccecccesccceeceeeeeeeeceeeeseeeseeeceeeeseeeeseeeseeeseeeesaeeseeeeseeeseeesaeeeees T S AlE eE e E E EE O E A E E E 7 TOC IG IP COS CY merienn setecaeae E A E E E E 7 Main Menu 3 Network Operators cccceeccsecceecceeeceeeeeeeeeeeeneeeeeeeeeteeeeaeeeaeeseeeneeeeetseesseeseeesaesenes 8 Scanning a Different Ne twork ccccccceccseecceseeeeeeseeeeaeeseeeseeeseeesaeeseeesageesaeeseueesaeesaeeseusensaeees 8 ETM re gee fc 10 ene ee ee eee eee ee ee ee eee ee 9 SU OS ANS ea ce tice cctvnecte es ce sence ease cence a gee ee seein os aoe nana E borane cetueeen anne etan 9 NODOT K cairear aen EERE near AEAEE EEEE AAE nina poet EE E E EE EEEE E AERE E ENGA 10 SUN a a E E E E E E 10 Main Me nu 5 Services serrr res teeeoeeeeneec EEEE EKE AEA a EAREN EEE ENEE KENESE 11 Radio Band Region Only Applicable to ET M7 70 1 cccccccceccceececeeeceeeececeeeeeeseeeseeeeaeeseeeeaes 11 Radio Band Restricting Scan to 2G or 3G oo eccceccceeeeceeeceeeeseeeeeeeeseeeseeeesaeeseeesseeseeeeaeeenes 12 SUM OW SCS ces
11. nate networks SIM ISP Connect Errors Possible errors may arise from incorrect authentication details incorrectly configured SIM or no Signal Possible Causes Further Details Corrective Action Incorrect ISP Login Details ISP Dial up Login Details are incorrect Verify APN and IP details are correct Ensure SIM is provisioned correctly for data services No or Weak Signal See above ETM770 Users Manual 201404RV01 Docx ETM Matteknik AB ETM Pacific Pty Ltd Ekbacksvagen 32 Suite 6 273 Alfred Street SE 168 69 Bromma North Sydney NSW 2060 Sweden Australia Tel 46 0 8 25 28 75 Tel 61 0 2 9956 7377 ci Fax 46 0 8 80 11 10 Fax 61 0 2 9956 5791 connecting things lt Email etm etm se Email info etmpacific com au Web www etm se Web www etmpacific com au ETM Pacific Pty Ltd Subject to change without notice
12. rt the device Radio Band Region Only Applicable to ETM770 1 Radio Band Region sets the Radio Band Groups applicable to the location you are in for example the applicable GSM GPRS region for Australia is 900 1800 MHz NOTE This menu item is not applicable for either the ETM770 2 or ETM770 3 ETM770 Users Manual 201404RV01 Docx Page 12 of 16 For Support Contact 61 2 9956 7377 Or support etmpacific com au Radio Band Restricting Scan to 26 or 36 This section allows the selection of a specific radio band for scanning First select Radio Band and press ENTER The following screen will then appear Remember to reset to Try All Bands if you want the unit to scan for all available services Use the UP and DOWN buttons to select applicable band and Press ENTER the should move to the selected radio band Use the UP DOWN buttons to select Return gt Main Menu and press enter Shutdown Device Use this function to turn the unit off Select Shutdown Device and press ENTER ETM770 Users Manual 201404RV01 Docx Page 13 of 16 Restart Device Use this function if you want to restart the device Select Restart Device and press ENTER For Support Contact 61 2 9956 7377 Or support etmpacific com au Note pressing the UP and DOWN arrows together will software reset the unit Using a Terminal Window to Configure the Unit Any suitable terminal program such as Windows HyperTerminal or ETM s own Term42
13. the unit Connector Mini USB SIM Holder Insert SIM this way up ______ SMA Antenna Connector Side catch back lock into paion An SMA Jack antenna connector is located top centre of a once SIM is inserted o the unit Any suitable antenna can be connected directly or via the use of an adaptor if required FME adaptor included with unit SIM Holder The units SIM holder is located top right of the unit di VOS Please take care to ensure the unit is off when the SIM is removed or inserted also ensure that the SIM is inserted correctly Buttons Z s ETM M tteknik AB gm i F f Current Model Older Units ON OFF Z T Connes Scroll Up Scroll Up Enter OK enter AAS Scroll Down Scroll Down ETM770 Users Manual 201404RV01 Docx Page 5 of 16 For Support Contact 61 2 9956 7377 Or support etmpacific com au Specifications Feature ETM770 4 1 ETM770 2 ETM770 3 3G UMTS HSDPA 850 900 2100 MHz 800 850 900 1900 Frequency Bands 2100 MHz 2G GSM GPRS Frequency 850 900 1800 1900 900 1800 MHz 850 900 1800 1900 Bands MHz MHz Screen LCD Backlit Backlit LCD Backlit Backlit LCD Backlit Backlit Battery Loot oo mAhr 3 7V a mAhr 3 7V ee mAhr 3 7V Rechargeable LIP Rechargeable LIP Rechargeable LIP typical use typical use typical use weight Operating Temperature 20 C to 40 C 20 C to 40 C 20 C to 40 C Range Charging
Download Pdf Manuals
Related Search
Related Contents
第2章 F9190RL1/RS1 光メディアコンバータ 取扱説明書 HG "polish brillance extrême (golvpolish)" Manuale Utente Soyo SY-7VDA Motherboard MANUAL DEL USUARIO - Whaley Food Service R15b_CSA Parte Tecnica Facciate Epson S5 User Replaceable Parts List Kocioł ścienny gazowy o wysokiej sprawności Plynové Copyright © All rights reserved.