User Manual for IMAGE IQ UI Corner Interactive System Software
Contents
1. Environment Avoid using the EWB in dusty damp or smog bound environments Read the EWB Maintenance section p 19 prior to installation and use Projecting Use the projector output format that matches the whiteboard format being used When ceiling mounting the projector please make the projector lens level with the top edge of the whiteboard The centre of the lens must on the horizontal centre of the Whiteboard The distance from the screen is determined by the optics of the projector Keystone correction should be used if necessary The Image of the projector must be in the centre of the effective area to the lower right of the receiver Extended Cable When the USB data line needs to be extended please use shielded twisted pair Max length should be less than 30m otherwise there may be loss of signal Production Certification and Warranty The product has passed FCC CE and ISO9001 and a three year warranty forthe receiver and a one year warranty for other accessories is offered 1 Installation of Hardware nu we _ Controller Signal Line WhiteBoard Date Line ePen Install and use the signal pen Pen tip Battery cover Rear cap 1 Unscrew the end cap of signal pen turning it counterclockwise q 2 Remove the battery cover by pushing the cover back away from the pen tip 3 Insert 1 AAA battery with the plus side up 4 Put the battery cover back and screw the cap back on c2. Signal 40 KHz ultrasonic 880nm infrared Minimum Height of writing or clicking 1 5cm Speed of writing or clicking 240point s Speed of signal tracking 3m s Effective resolution 9600x4800 300dpi Effective diagonal 80 4 3 100 16 9 Active area up to 1 2m X 2 4m Working hours of signal pen battery more than 52 hours sensible pressure gt 10g Working hours of electronic eraser battery more than 20hours sensible pressure gt 10g Connect PC through USB port plug and play external power is not required unless using Bletooth connection Length of cable 2m from receiver to controller 3m from controller to PC Power supply signal pen and electronic eraser use battery the receiver and controller are powered by USB port unless bluetooth wireless used power adaptor then required 3 System Requirement In addition to Projector Whiteboard or flat panel display CPU Based on X86 CPU pentium166 or above Memory 128 MB RAM Hard Disk 30 MB free space USB Port at least one available USB port 4 Storage and Operating Specifications Storage Temperature 40 degrees to 60 degrees Humidity 0 to 95 Operation Temperature 0 degree to 40 degrees Humidity 15 to 85 Warning prior to Installation Donotlook directly at the projector light Don tleave cables that may causing tripping If the cables must be put on the floor straighten and tape them to the floor using gaffer tape
3. write and erase capture screen move and zoom revolve combination hyperlink transmit export spotlight magnification reveal and so on 2 Mode storehouse figure label storehouse standard figure storehouse auto edit functions are provided Support figure format such as JPG GIF and figure stratification technology 3 Real time video can be saved as AVI format auto control of video play video handwriting labels are supported by operating system above WINDOWS SP2 4 Save original label trace of PPT in its original format and operate directly in the relevant application software 5 Edit functions of text figure and image 6 Achieves long distance interactive teaching through Internet and Intranet 7 Provides various working modes such as mouse writing and sign note edit and long distance interaction etc 8 Software upgrades provided FREE Visit website www iqboard com au for the latest software version ae Product Specifications Dimension of receiver 115 mmx68 mmx32mm Dimension of controller 115 mmx75 mmx28mm Dimension of package 370 mmx207 mmx128 mm Standard Net Weight 1 5kg 100g Specification and Configuration 1 Standard package supplied 1 x Receiver incl receiver attachment mount 1 x Controller 1xePen 1 x 2m Din cable 1 x 3m USB cable 1 x AAA battery Manual CD containing driver and software 2 Technical Parameters Power consumption less than 0 5W OS Win2000 XP 2003 Vista
4. also be located in the same Downloads section If you have any technical queries contact ABI staff on 02 9938 6866 3 Quality Warranty Three years warranty is provided on the receiver amp controller and its operation The service back to base so the client has to return the board to ABI and ABI will organize the return of the board to the user It does not include 1 Accessories pens batteries cable 2 Physical damage including surface scratching marks build up of dirt and pen ink and distortion caused by faulty installation 3 Damage resulting from operation not as stipulated in the user manual 4 Warranty on the product will be voided if the board is disassembled by the user or an unauthorized repairer 5 Damage caused by force majeure such as natural disaster thunder and lightning and accident 6 Product accessories consumable parts such as CD user manual package fixing parts batteries the shell the consumption components are all not include into the free repairing or exchanging a purchase clause 7 The user must be able to provide a copy of the original invoice 4 After Sale Service 1 ABI provides a service centre support to service and repair the IQ Whiteboard Contact ABI on 02 9938 6866 to discuss any problems or organize a service 2 Repairing When the warranty period has expired or the damage is not a warranty issue the customer will be charged for any repair Customers ca
5. User Manual for IMAGE IQ Ul Corner Interactive System Software Version 5 0 abi Copyright C 2009 A Brighter Image Pty Ltd Web www abimage com au Tel 02 9938 6866 Fax 02 9938 6899 E mail info abimage com au Contents Brief INtTrOGMUCTIOND isasid anaana aeaaaee aaa a a aaa aa a iaaa aaia 4 5 Al SIS CIC ALOIS E E E P A A A E E 5 2 Warning prior to Instalati N sssrin nirai ai 6 Installation Method cccccccccsscsecesseceenseseceeseeeeeneseenauseeeaseeeenauseeuuseeeeeeesenauseesenueseneeeees 7 10 1 Installation Of Hardware oo ccc cecccceeeecesseceseeeueceeeuceeseeueeeueaeeeeueeeueaaeeeeaeeeeeaaess 7 10 2 Installation and Uninstall of Software 0 0 cee ccecccceeecceseeeceeeeeeeeseeeeeeueeeseseeeeeeaneeens 10 Uninstall software oo cece cccccccceeececececeeeeececueuceeeuceeeeaeeeeaeueeeesaaeeeuaeeeeeeaeeeeuaeeeuneees 10 3 GONMECEING data ING sccscsstesececedededeAccscsscctascesevizecdeas idecedssesoaededede e eassenesaascaneixesdesexeees 10 Hardware USC ccsssccnce cctchcececedececcctdsctecndscccaseducussuecoausedeusesedeessccoastescdeasaeceass dosdesceuenseceunws 11 12 le Start USING the Systemi siitin deci ewes ie cece edad Eie danara aAa 11 PDE Eie a E EEEE E TEE EE EEEE E EE A E 11 12 PAGS E ENEE ET A NAE IEEE A A EAEE TT 13 14 Brief Introduction The IMAGE IQ UI Corner Interactive System incorporates the latest equipment for teaching training and conference presentation It incorporates the latest high tec
6. h research results such as top electronic technology software technology internet technology etc It enables static presentations on whiteboards or flat screen displays to be made interactive ideal for conference distance education and training It will gradually replace traditional teaching methods and conference modes It may be used by any profession in different situations The IMAGE IQ UI Corner provides abundant software functions It provides users with reliable rapid and nimble operation Its functions are as follows 1 Operation technology Ultrasonic technology 2 System supported Laptop PC Multi country language Win2000 XP 2003 Vista Mac 10 3 or later 3 Board Compatibility Can be fitted to any standard whiteboard flat panel monitor LCD or LCD TV or Rear Projection TV 4 Physical properties Supports any kind of projector image resolution 1 5cm Induction Height for writing or clicking 240 S processing rate High response rate sensitive operation 5 Installation Provide with corner attachment to fit to board or monitor Receiver slides into corner attachment 6 Computer Connection Standard USB slot Plug amp Play no need of external power 5m of connection length included max 20m extended cable in addition is acceptable 7 Driver Corresponding hardware driver and USB driver are needed supplied 8 Software functions 1 Enables PC interaction save and print send email copy and paste
7. he protective layer from the tape 6 Align the two sides of the receiver base with those of the frame corner push the base down until the base and the frame are firmly stuck The installation is complete T sites Tape 1 I Iin case the frame of the whiteboard or LCD TV has curved corners use the following method 1 Wipe out the dust on the left top corner of the screen or board surface 2 Remove the receiver base 3 Cut 5cm of the double sided tape 4 Affix the double sided tape on the corresponding position to the underside of the receiver 5 Take off the protective layer 6 Stick the receiver on the screen or board The installation is complete m fi Tersided tape Whiteboard Caution Ensure that the sides of the receiver are parallel ro the frame of the whiteboard or flat panel Also the receiver must be parallel with the surface of the board or panel to en sure accuracy in the operation of the system 9 2 Installation and Uninstall of Software Install driver and interactive whiteboard software Note There are 2 software programs to load Please double click on the software in the CD supplied and follow the instructions a WhiteBoardGeniusDRIVE exe Board drivers and calibration software Follow the installation prompts To uninstall go to Start Programs ReturnStar Whiteboard Genius Uninstall and follow prompts b Easiteach Starter Board Presentation software 1 Do not connect the data l
8. ine before installing the software 2 Lowest Specification of PC Pentium III GOO0MHz or above recommended 128MB RAM 1G HDD one USB port Resolution 1024x768 16bit high color or above 3 System Requirement MS Windows 98 Me 2000 XP 4 Some special functions may be limited by the OS used Run the file on the CD and install it according the prompts Uninstall Click Start gt Programs gt Easiteach gt Uninstall to uninstall this software You also can open Control Panel select Add Remove Programs and in the list of currently installed Programs select Easiteach Software then press the Change Remove button to remove 10 Start Using the System Select Start gt Programs gt Returnstar Whiteboard Genius gt Start or click the shortcut on the desktop to start the Whiteboard Genius A taskbar icon will appear on the right bottom of the screen as follows If the system prompts Hardware not found Please check your connection Please check the controller indicator and refer to Chapter 7 FAQ for solution After you start the Whiteboard Genius the red controller indicator should turn green g hardware has not been found the taskbar icon is me it means the hardware is connected Caution After starting Projector Genius if the taskbar icon is B it means the Mouse Right key Start Whiteboard Geniust4 Grientici AboutiH Exit st Odie _ TEF Mouse Right
9. iteboard Genius driver and orientation program are not installed successfully 3 There is an object in front of the receiver that blocks the signal 4 Batteries of signal pen or electronic eraser are run out or signal pen or electronic eraser is broken 5 The computer is not rebooted after installing the driver and orientation program of IQ Whiteboard 6 The application of electronic whiteboard is not installed 7 The USB cable or signal line is loose or broken The orientation is not precise 1 Bad orientation 2 The batteries of signal pen or electronic eraser are run down or signal pen or electronic eraser is broken 1 The computer is not under normal running or the memory is occupied too much 2 The batteries of signal pen or electronic eraser are run down or signal pen or electronic eraser is broken 3 There are interference source around the system such as flashing red light continuous mental collision sound etc Solution Check the USB port or the signal port and re connect In case the controller port needs to be replaced Please contact your dealer or ABI Please contact your dealer or ABI Please contact your dealer or ABI Close the IQ Whiteboard start icons and re start the IQ Whiteboard Start the IQ Whiteboard software Uninstall the old driver and orientation program and reinstall Remove the object Replace batteries signal pen or electronic eraser Reboot your co
10. key If you click this item you can use the mouse right key function for one time Start Whiteboard Genius Pause Whiteboard Genius Click Start Whiteboard Genius to use the signal pen to operate the board If you want to stop using Whiteboard Genius temporarily click Pause Whiteboard Genius Orient Click this item to enter the orientation interface and orient the whiteboard If no hardware has been found the system will popup a prompt window as follows ReturnStar Whiteboard Genius x A Hardware is not connected please connect it In order to make the Whiteboard Genius work normally you need to orient it the first time you use it After you start the Whiteboard Genius click the taskbar icon and select Orient option on the popup box the Orientation Window will appear as follows 11 Press ESC to exit the Orientation Window We use 9 Points orientation because of its high precision If you cannot find the red on the projection image you have to adjust the projection area until you can see it The course of orientation is very easy you just need to use your signal pen to click the 9 red crosses in sequence After it is finished click Ok to exit then you could operate the virtual whiteboard properly by signal pen or electronic eraser g Caution 1 if your signal pen did not locate the accurate central point or clicked the wrong point or the next fxed point appeared without press plase pres
11. lockwise 4 2 Setup receiver IQBoard UI D003 can skip this step The receiver can receive the signal emitted by signal pen and then identify its location on screen or board Generally the receiver is fixed on whiteboard or RP TV by two sided tape or screw ve When using the signal pen please beware that 1 Write at proper strength to guarantee that the signal pen can emit writing signal slight buzz can be heard when youhold the pen close to your ear 2 Try your best to make sure the signal pen is held perpendicular 15 to the whiteboard 3 The position where you hold the signal pen should not be lower than the middle part to ensure you don t block the signal as follows Writing strength a Slight buzz Vv Whiteboard Installing the receiver The receiver can receive the signal emitted by signal pen or electronic eraser detect their location on screen or board send it to controller through signal line and the controller will transmit the location and operating information to computer through USB cable Generally the receiver is fixed on the whiteboard or LCD TV by two sided tape or screw In case the frame of the whiteboard or LCD TV is level and smooth use the following method 1 Wipe out the dust on the left top corner of the frame 2 Install the receiver on its base 3 Cut 5cm of the double sided tape 4 Affix the double sided tape on the correspond position of the receiver base 5 Take off t
12. mputer and then start IQ Whiteboard again Install electronic whiteboard application Re plug or change the USB cable or signal line Start the orientation process again Start the orientation process again Replace batteries signal pen or electronic eraser Close some opened applications or restart the computer Replace batteries signal pen or electronic eraser Avoid the interference source and try again Behavior 6 The orientation is not precise or when orienting the red orientation cross moves randomly or the cursor flashes greatly 7 The action of click or double click is difficult to control FAQs Reason 1 Trapezoid distortion in projector 2 There are interference source around the system such as flashing red light continuous mental collision sound etc 1 You are not used to the operation yet 2 The mouse response is too slow or too fast Solution Keystone correct the projector Avoid the interference source and try again When operating please close the pen point to the surface and keep it steady Please practice 2 5 minutes until you master it Slow the mouse response speed Product Service 1 Software Upgrade Free Updates of the software will be supplied when available Check the website for information on the latest version It is listed under Downloads on the Home Page www iqboard com au 2 Technology Service Acopy of the User Manual will
13. n purchase related parts from ABI Pty Ltd When sending the damaged parts back to ABI for repair the customer has to pay the transportation costs and repair Copyright This user manual is for the IMAGE IQ Whiteboard the copyright belongs to A Brighter Image Pty Ltd We have the right to modify the content of user manual without notice
14. s ESC an the keyboard to exit this orientation and re orient Otherwise your writing pen or finger will not match the cursor accurately 2 Please to make your signal upright when onenting 3 In case the relative position and angle of the projector and receiver is changed or the postion projection image is shifted or the driver or the monitor resolution is altered please re onent For information on the Easiteach software refer to the Easiteach Instruction manual wif 2s Behavior 1 The controller indicator is not lighting or the indicator turns red after start the Whiteboard Genius 2 Signal pen or electronic pointer cannot control the virtual whiteboard or it can control the computer but cannot write 3 Signal pen or electronic eraser could only control part of the virtual whiteboard 4 Drawing line is irregular or it is hard to handle while remote control 5 When writing or operating by signal pen or electronic eraser the response is slow or inconsecutive FAQs Reason 1 The signal line is not well connected with the controller or the USB cable is not well connected with the computer 2 The computer USB port or the controller port needs to be replaced 3 The signal line or USB cable needs to be replaced 4 The indicator is not lighting but the IQ Whiteboard can be normally used 5 The IQ Whiteboard has been started too many times 1 IQ Whiteboard not working 2 Wh
Download Pdf Manuals
Related Search