DIP1000 HDMI with USB Over IP LAN Installation and User's Manual
Contents
1. USB Composite Device USB PnP Sound Device Select USB PnP Sound Device as the Windows default sound device in order to use the speaker and microphone on the DIP1000R Line Out green and Microphone jack pink Attach USB devices like keyboard mouse pen drive audio speak microphone to the AV DIP1000R 4 USB A ports Note you will need DC 5V with 4A power adapter if all DIP1000R 4 USB ports are used To gain the USB access right among multiple DIP1000R press and hold for more than 3 secs the Link button of the DIP1OOOR until an OSD message of Requesting USB is displayed then release An OSD message of Starting USB will be displayed if it successfully Meanwhile the previous USB Master unit will show an OSD message USB Stopping Reset to Factory default and EDID Operation 1 To Reset the DIP1000T to the Factory default setting Press and Hold the Button 1 then Power ON until Green and Red LED blinking I 2 To Use the DIP1000T Loop out monitor EDID Press and Hold the Button to Power ON until the Green LED starts blinking 3 To update the DIP1000R EDID Press and Hold the Mode button to Power ON until Green LED is blinking 4 To Reset the DIP1000R to the Factory default setting Press and Hold the Link button to Power ON until Green and Red LED s are blinking Remote Power On Off optional This function is designed for remote Power on off control of your PC through the DIP102. IR signal from the DIP1000R to the AV sources 1 Connect the supplied IR blaster cable to the IR blaster socket at the rear panel of the DIP1000T Transmitter Please check if the LED on the IR blaster is correctly positioned in the front of the AV sources Make sure your infrared remote controller is able to align the DIP1OOOR IR Rx port When you press any key on the remote controller the DIP1000R receives the IR signal and transmits it to the DIP1000T Then the IR signal is delivered to the AV sources device through the LED on the IR blaster cable The LED of the IR blaster cable must be facing the IR receiver of your Windows Media Center Edition PC TV tuner card or Blu Ray player Digital Video and Audio Source DIPLOOOR pes a IR Blaster ay w gt CAT5e 6 6a 7 Cable gp up to 100m ie ef ral Pa IR Remote Contorl
3. USB PnP audio device Set the OS Pat 13 Line OUT default audio to the USB PnP audio device that is created by the No Component Description DIP1000T 1 Green LED Power Link Green Blinking Red Off System is starting up 14 Gigabit Ethernet For connecting directly to DIP1000T or via a Gigabyte Switch 2 Red LED System status Green On Red Blinking Linking or waiting HDMI input Green On Red On Connection established 4 bit DIP switch for 16 ID settings To enable Transmitter Receiver as 3 Link ID a pair or group the transmitter and receiver must be set with the same Link ID 4 USB Host For remote USB devices such as USB KB Mouse storage audio 5 IR Rx optional Remote Universal IR receiver 6 Remote Power On Off Button for Remote PC Power On Off function p for 1 i second Anti Dither Mode Setting to Anti Dither optional Press button for gt 3 Mode to achieve better video quality for seconds 7 Mode button some ATI graphic cards Press and Hold at Establishes EDID as the system EDID Power ON until Green LED blinking update DIP1000T EDID Press button for 1 second gt i Fress Er 3 To enable USB access 8 Link button Press and Hold Power ON until Green and Resets unit to the Factory default setting Red LED starts blinking 9 DC 5V In System power input 5V 2A or 4A when used with 4 x USB devices Connects to HDMI display For DVI display you may
4. need a padded HDMI to DVI adapter cable 11 RS 232 optional Provides Serial over IP function Microphone Input for the USB audio device Set the OS default 12 Mic IN audio device to the USB PnP audio device that is created by the DIP1000T Installation 1 Ensure that the Link ID of both the DIP1000T and DIP1000R have the same settings Attach the HDMI display to the DIP1000R HDMI Out port Power on the DIP1000R An AVExtender logo will be displayed If this does not appear an error has occurred with either the DIP1000R HDMI cable or the display You can connect multiple DIP1000R s and multiple DIP1000T units to your Gigabit Ethernet switch Alternatively use a CAT6 UTP cable straight EIA 568B to directly connect a DIP1OOOT with a DIP1000R as a pair Attach the HDMI source PC or Blue Ray to the DIP1000T HDMI In port and then power On the DIP1000T The first DIPLOOOR that is detected by the DIP1000T will gain the USB access right If you are using your PC as your HDMI source you will see your HDMI display EDID information on the PC graphic card control panel If not then something is wrong either with the DIP1000T or HDMI cable Output HDMI with audio from HDMI source and check if they are correctly displayed on your HDMI display USB over IP installation I 10 11 12 Connect DIP1000T USB to PC port to a Windows based PC USB port by a USB A B cable 3 devices will be detected Generic USB Hub
5. 00R Remote Power On Off push button PC Board DIP1000T r Transmitter A E z Connect to a Remote i Power button Po i Fewer Cable Te miem H hu Cr I Connect to Power Reset 1 Connect the 3 5 mm plug of the supplied control cable into the DIP1000T Transmitter Remote Power on off socket 2 Atthe other end of the control cable there are 2 x separated 2 pins holders Connect any one to your PC board Power Reset jumper and the other holder connects to your PC Reset button cable 3 On the front panel of the DIP1000R Receiver press the Remote Power On Off button You can then remote Power Off your PC By pressing the button again it will turn on your PC again RS 232 Control optional This function is designed for remote access and control of your RS 232 device Cierrebet ts RJA hasu Connect the 3 5mm mini stereo plug of the supplied RS 232 cable to the RS 232 socket at the rear panel of the DIP1000T Transmitter and then connect the DB9 Female connector of the supplied RS 232 cable to the COM port of your PC Connect the 3 5mm mini stereo plug of the supplied RS 232 cable to the RS 232 socket at the rear panel of the DIP1000R Receiver and then connect the DB9 Male connector of the supplied RS 232 cable to the RS 232 device RS232 Pin mssignments sou se RO ef e 6 e se se DIP1000R Gg B EJEJER DIP1000T Infrared Control optional This function is designed to transmit
6. DIP1000 HDMI with USB Over IP LAN Multi cast Version Installation and User s Manual For Sales and Service please contact ICP Global Pty Ltd Phone 02 9314 2092 Fax 02 9344 9537 Suite 603 Level 5 152 Bunnerong Road PAGEOOD NSW 2035 Date October 4 2011 l Introduction The DIP1000 system is a perfect solution to extend HDMI USB and optional IR RS 232 Remote Power On Off over IP networks It includes the main units of DIP1000T transmitter and DIP1000R Receiver as well as the below mentioned optional accessories The DIP1OOOT transmitter connects with a PC or any other device with via HDMI source The DIP1000R receiver connects to HDMI display speaker microphone USB devices Keyboard Mouse Storage and RS232 devices It is based on the standard Ethernet IP network Gigabit or Fiber LAN switches can be used for inter connection or multi casting Optional Accessories 3 5m mini stereo to DB9 Female RS232 control cable 3 5m mini stereo to DB9 Male RS232 control cable 3 5m mini stereo to 2 pins Remote Power on off cable IR blaster cable Panel View 4 bit DIP switch for 16 ID settings To enable Transmitter Receiver as a pair DIP1000T Transmitter 1 2 34 6 Link ID r or group the transmitter and receiver must be set with the same Link ID 7 Gigabit Ethernet For connecting directly to DIP1000R or via a Gigabyte Switch 8 RS 232 Control Provide Serial over IP function optional 9 DC 5V I
7. n System power input DC 5V 2A Connects this USB B to PC 1 USB audio device USB audio device will be detected when it is attached to PC in Windows OS 2 Virtual 4 port USB Hub for remote USB devices 11 HDMI IN Connects to HDMI Source For DVI source you may need a HDMI to DVI adapter cable 12 IR Blaster 10 USB to PC No Component Description Connects to external IR LED 1 HDMI Loop out HDMI Loop out for Local Monitor optional Press button for 1 second Press button for gt 3 Output video to both Remote and Loop out DIP1000R Receiver 2 Button 1 seconds monitors Press and Hold Power ON until Green and Red LED s Resets unit to the Factory default setting start blinking P for 1 pes sumer Switch to Video or Graphic mode second Anti Dither Mode Setting to Anti Dither Switch video to Remote or Loop out monitor Panel View U8 Link IL IR PEx P button for gt 3 i l l 2 Button 2 ame eee Mode to achieve better video quality for some ATI graphic cards Press and Hold Power ON until Green LED Establishes EDID from Loop out monitor starts blinking Gigabit Ethamet 3 Red LED System Green Blinking Red Off System is starting up 4 Green LED Green On Red Blinking Waiting for HDMI input source Power Link Green On Red On Connection established 41 1213 14 5 Remote Power Connects to PC motherboard for Remote Power On Off 3 4 Stereo Audio output for the
Download Pdf Manuals
Related Search