User Manual - Skope Industries
Contents
1. Operation User Manual Controller Alarms Display Buzzer Alarm Description Action sz E a i l i I IT I EJ EN r I E EN Operation User Manual O O Q D my E EE rr A Flashing A Flashing A Flashing A Flashing A Flashing A Flashing A Flashing None O Flashing A Flashing A Flashing None None SKOPE OD400 Product HIGH 1 Check the cabinet product loading to ensure temperature alarm ventilation slots are not blocked and that auto reset product does not overhang the shelves 2 Ensure the cabinet is installed with good refrigeration unit ventilation 3 If immediate alarm recovery is required unplug the cabinet from the power supply for 1 minute then reconnect to power supply Product LOW temperature alarm auto reset If alarm persists contact SKOPE Refrigeration system 4 Check refrigeration ventilation Ensure clear high temperature airpath at the top and front of the cabinet to pre warning auto extract hot air A minimum of 200mm clear reset space is required above and in front of the refrigeration unit 2 Ensure the cabinet is installed in a suitable Refrigeration system environment high 3 To reset the CHt alarm unplug the cabinet temperature shutdown manual reset from the power supply for 1 minute then reconnect to power supply If alarm persists contact2. User Manual SKOPE Contacts SKOPE Industries Limited NEW ZEALAND CONTACT Head Office PO Box 1091 Christchurch New Zealand Freephone 0800 947 5673 Fax 03 983 3896 E mail enquiry skope co nz Website www skope co nz AUSTRALIAN CONTACT A B N 73 374 418 306 PO Box 7543 Baulkham Hills B C NSW 2153 Australia Freephone 1800 121 535 Fax 1800 121 533 E mail enquiry skope com au Website www skope com au Trademark Infringement The SKOPE trademark on this product is infringed if the owner for the time being does any of the following e Applies the trade mark to the product after their state condition get up or packaging has been altered in any manner e Alters removes including part removal or obliterates including part obliteration the trade mark on the product e Applies any other trade mark to the product e Adds to the product any written material that is likely to damage the reputation of the trade mark Notice of the above contractual obligations passes to e Successors or assignees of the buyer e Future owners of the product OD400 SKOPE Open Deck Chiller User Manual MAN1590 Rev 9 1 Jul 2015 2006 SKOPE Industries Limited All rights reserved SKOPE Industries Limited reserve the right to alter specifications without notice SKOPE is a registered trademark of SKOPE Industries Limited
3. SKOPE Ambient probe fault also flashes rE Evaporator probe fault Condenser probe fault To reset alarm unplug the cabinet from the power supply for 1 minute then reconnect to Defrost over time power supply limit If alarm persists contact SKOPE Real time clock fault Controller E prom error Controller E prom error Start defrost request None End defrost request 11 SKOPE OD400 3 Servicing Lighting Cabinet The cabinet has two interior side lights each fitted with one fluorescent tube Interior Lights Model Fluorescent Tube Part No OD400 14W 860 T5 fluorescent tube 016mm x 550mm ELLO601 To replace a fluorescent tube 1 Disconnect the cabinet from the power supply 2 Remove the side light diffuser by compressing the rear of the diffuser until it disengages from the side housing see below I Light Diffuser N i Printing Fluorescent Tube Red Lamp Holder 3 Rotate the red lamp holder outwards until the fluorescent tube is released see above Rotate inwards to lock the tube in position 4 When fitting the new fluorescent tube ensure the printing on the tube is at the bottom as the orientation of the tube is important Cleaning Cabinet When necessary wipe both the interior and exterior of the cabinet with a damp cloth Ensure the cabinet is disconnected from the mains power supply before cleaning the cabinet CAUTION Do NO
4. OD400 SKOPE Open Deck Chiller U _ Cie O N s o 6 0 0 SEKOPE ED g Refrigeration SKOPE Warranty Protection Register now for peace of mind It s quick and simple Take a few minutes to register your SKOPE product and enjoy more efficient support plus other warranty benefits When registering make sure you have your cabinet serial number at hand To register online Visit our website at www skope com warrantyprotection then complete and submit the online registration form Or freephone 1800 121 535 Australia 0800 947 5673 New Zealand SKOPE 1 year Extended Warranty Extend your Warranty Protection by 1 year during registration Please check you have not already organised an extended warranty through your dealer at time of purchase For pricing information on an extended warranty visit www skope com warrantyprotection Service amp Support We know you will get years of satisfaction from your new SKOPE product when you follow a few simple preventative maintenance guidelines Helpful information is available on our website www skope com serviceandsupport Thank you for purchasing a SKOPE refrigeration product SKOPE OD400 User Manual Installation Safety First lt 6 cine dwdeccuencebawadedeeed deem dedae dae ae oat 4 Cabinet Location a na naana aaaea eee 4 Power Supply 2 0302 e dei a be a a id wx 5 Air Movement lluua aaa aaa aaa ee eee 5 Ven talon sacz ani hora pets aceit
5. T wash any solvents down into the refrigeration system as this could lead to refrigeration failure 42 Servicing User Manual SKOPE OD400 Condenser To ensure trouble free performance the condenser coil must be kept clean Coil We strongly urge monthly cleaning with a soft brush to remove dust and fluff A thorough cleaning is required by qualified service personnel every six months The condenser coil must be kept clean for efficient and reliable operation WARNING Disconnect the chiller from the power supply before cleaning the condenser coil To clean the condenser coil 1 Disconnect the cabinet from the power supply 2 Remove the front panel from the cabinet by removing the fixing screws near the bottom of the panel and lifting it up and off the cabinet Fixing Screw Front Panel 3 Brush the condenser coil with a soft brush 4 Refit the front panel and reconnect to the power supply Advanced Servicing Advanced servicing should be carried out by an authorised service agent Servicing must comply with all relevant standards and regulations including Australian and New Zealand Refrigerant Handling Code of Practice 2007 Part 1 and Part 2 and AS NZS 3000 2000 Wiring Rules Detailed service and spare parts information is available in the SKOPE OD300 400 Service Manual SKOPE part no MAN1591 Please contact SKOPE Customer Services for advice regarding disposal of the product Servicing 13
6. during normal operating mode Flashes when the door is open HACCP HACCP n a CONTINUOUS CYCLE n a No Item 1 2 a 3 4 0 6 HK 8 aux A 10 O 11 y 12 13 14 15 8 Operation User Manual Defrost Continuous Cycle Temperature Setpoint Operation User Manual SKOPE OD400 To ensure efficient operation the electronic controller forces a defrost cycle when required During a defrost cycle the compressor stops DEF and the 2 will display on the electronic controller faceplate The cabinet will resume normal operation once the defrost cycle has finished A manual defrost can also be initiated by pressing and holding the button The continuous cycle can be used to pull down the temperature of product inside the cabinet quickly During a continuous cool down the compressor runs continuously for a set time To start a continuous cycle 1 While the cabinet is switched on and running press and hold the dk and w buttons for five seconds The lt symbol will display during a continuous cycle To stop a continuous cycle 1 The electronic controller will automatically stop the continuous cycle after a period of time The continuous cycle can be stopped by pressing and holding the a and y buttons for five seconds The chiller is manufactured with a pre set control temperature set point of 2 5 C standard or 1 C dairy If this set point does not match your required storage te
7. e A 9 SNMG sensei der anera wos Sahu deed AGR EREMIE 6 Adjustable Shelves 0 0 000 0 cece nano 6 Cantilevered Shelf Brackets o ooooooooooo 6 LO OAQING gee eneas pubs amp ate Ge ane oe pane eee om e dde ws 6 Operation Automatic Start Up anana aaa aaea 7 Night Blind optional OD400 only 7 Electronic Controller 0 0 0 0 0c ccc eee 8 Controller Display 0 00 cc eee 8 Controller Operations 0 0 00 ccc ee eee 8 Temperature Setpoint 0 0 0 nono 9 Controller Reset 00 0 9 Controller Alarms 0 0000 cece ee eee ees 10 Servicing DONUNJ 4a sm Gils ob BS sted aoe Ow OS Ee WEG tdci S Se Wd 12 Cabinet Interior Lights 20 0 0 12 Cleaning soe needa oe wee a ad aha E 13 CAINS at ck SERA ne wah Greene Gi dows Dae Bord nS Geant ee A 13 Condenser Coil LLL aaa aaa aaa aa aaa aaa ees 13 Advanced Servicing 0 0 0 aaa aaa aaa aa aa aaa 13 CONTENTS SKOPE OD400 1 Installation Safety First Always observe safety precautions when using any electrical appliance Read these instructions carefully and retain them for future reference o When the appliance is used by or near young children or infirm persons close supervision is necessary especially to ensure children do not play with it Do not use this appliance for other than its intended use Do not cover the grilles or block the entry or exhaust of airf
8. est place possible because it will use less power and last longer Although it operates in environs up to 25 C at 60 RH climatic class 3 it would be unwise to make the chiller constantly run at the upper end Ensure the cabinet sits on a level surface to prevent the condensate tray from overflowing A Installation User Manual SKOPE OD400 Power Supply The power supply cord which exits out the bottom rear of the cabinet Air Movement Ventilation Installation User Manual should be retrieved before the cabinet is positioned The power supply must be plugged directly into a dedicated wall socket Extension cords or multi boxes should NOT be used The cabinet must NOT be situated where it is affected by air conditioning air outlets ventilation fans or air re circulation fans as this will compromise the airflow and thus product temperature in the open cabinet zone There must be NO air movement directly into the cabinet opening Air movement will cause failure of the air curtain over the product resulting in excessive temperature rise Detectable air draft will adversely effect the cabinet operation Maximum air movement across the cabinet opening must not exceed 0 2 m s IMPORTANT There must be NO air movement directly into the cabinet opening Never store cardboard cartons or other items in front or rear of the refrigeration unit The ventilation slots in the front and rear of the cabinet must be kept clear at al
9. l times For efficient operation of the chiller it is essential that adequate ventilation clearance be provided around the refrigeration unit Normal operating conditions should not exceed 25 C at 60 RH Climatic Class 3 It is critical that the hot refrigeration exhaust air is not restricted and that it can easily flow up away from the cabinet IMPORTANT For efficient operation of the chiller it is essential that adequate ventilation clearance be provided around the refrigeration unit The minimum clearance between the cabinet back and the rear wall must be at least 75mm The minimum clearance above the cabinet must be at least 200mm The cabinet should also have at least 60mm clearance on both sides 75mm Ceiling lt 200mm o Unimpeded refrigeration exhaust airflow clear of any obstruction Front Rear Wall Air intake gt SKOPE OD400 Shelving The SKOPE Open Deck Chiller is supplied with the following standard shelving items packed inside the cabinet a 1 Adjustable Height Top Shelf shallow depth a 1 Adjustable Height Middle Shelf medium depth a 1 Fixed Bottom Shelf deep supplied fitted m 4 Cantilevered Shelf Brackets 2 shallow and 2 medium depth Adjustable The adjustable height top and middle shelves are each held in place by two Shelves cantilevered shelf brackets Top Shelf shallow Middle Shelf medium Bottom Shelf deep To fit the adjustable height shel
10. low by placing objects up against the refrigeration unit m Do not probe any opening m Only use this appliance with the voltage specified on the cabinet rating label o Ensure the chiller has adequate ventilation as this is essential to economical high performance Be careful not to touch moving parts and hot surfaces For your own safety and that of others ensure that all electrical work is done by authorised personnel m Ifthe power supply flexible cord becomes damaged it must be replaced by an authorised service agent or similarly qualified person in order to avoid a hazard m Ensure all necessary safety precautions are observed during installation or removal of the refrigeration unit m he chiller is not designed to be stable while in motion Use extreme caution when moving or transporting it WARNING Disconnect the cabinet from the mains power supply before attempting any cleaning or maintenance CAUTION Never overload the power supply which could damage the chiller and product See the rating label inside the cabinet for the safe power supply and current draw CAUTION Do NOT allow liquids or any other materials to drain into the bottom of the cabinet as this could lead to refrigeration system failure Cabinet The location of the chiller may be the single most important decision that will Location extend its life and ensure economical high performance We recommend that you put the chiller in the cool
11. mperature it is recommended that you change the set point accordingly The set point can be adjusted between 0 C and 4 C To view and adjust the temperature setpoint 1 To view the setpoint press and hold the Set key for 2 seconds until the setpoint value flashes 2 To adjust the setpoint press either the A def ax and w keys to display the required setpoint value 3 Press the Set key again to memorise the new setpoint value If this is not done within 60 seconds changes will be lost and you will need to repeat the above procedure SKOPE OD400 Controller To delete program modifications and reset the controller to SKOPE default Reset program or when a replacement controller is being fitted a Controller Reset 10 Press the or Immediately press the Set key to must be performed To reset the controller Disconnect the cabinet from the power supply 2 Press and hold the y key while plugging the cabinet into the power supply this may require two people After a few seconds the controller is reset and program mode bn0 is displayed The controller must never be left in program mode bn0 as failure will occur y keys to select bn1 standard or bn2 dairy for SKOPE default programs confirm the preferred program If not confirmed within 60 seconds the cabinet will remain in program mode bn0O and cause failure If this occurs repeat the above procedure
12. nd pull down Hook both ends of the handle under the two hooks behind the front air shield taking care not to damage the air shield SKOPE OD400 Electronic Controller Introduction The electronic controller controls the chiller and signals temperature alarms The preset temperature setting controls the product temperature between 0 C and 5 C The electronic controller is pre programmed and usually requires no initial setup or additional programming SKOPE does not recommend that the settings be changed unless necessary Faceplate Because the electronic controller plays such an important role it s helpful to know the parts of the faceplate you may use Description MUTE Mutes the audible controller alarm LIGHT SWITCH Press and hold to switch the lights on and off not available on all cabinets SET Service use only MANUAL DEFROST Press and hold to initiate a manual defrost cycle COMPRESSOR ON when the compressor and condenser fan starts Flashes when activation of the compressor is temporarily delayed FAN Shows when fan is operational DEFROST ON when the defrost is activated Flashes when the activation of the defrost is temporarily delayed due to procedures in progress AUX nia ALARM Flashes in the event of alarms CLOCK On when real time clock is enabled LIGHT On when the cabinet lighting is activated A SERVICE Flashes in the event of malfunctions 586 0 DISPLAY Shows three dashes
13. on and checking for air movement inside the cabinet The internal cabinet air will continue to circulate at all times The compressor will start after approximately one minute will switch off when the cabinet internal temperature reaches approximately 1 5 C and on again at approximately 4 C Electronic When the cabinet is connected to the power supply the Controller electronic controller will display the current cabinet temperature The compressor LED will indicate the compressor is operating and the evaporator fan LED will normally come on within 2 minutes see page 8 for controller display Cabinet Lighting The cabinet interior lights will both go on when the cabinet is plugged in and will stay on permanently while the cabinet is connected to the power supply The cabinet lighting can be manually turned off and on by pressing the controller key for 2 seconds not available on all cabinets The lighting will go off during the CHt high temperature shutdown see page 11 for controller alarms The fluorescent lights will require a period of time to stabilise following initial start up Night Blind Only applicable to cabinets fitted with a night blind Operation User Manual The OD400 cabinet has a night blind you can pull down to save power when the chiller is not being used This blind is located inside the cabinet behind the front of the cabinet lid To close the blind grab the handle at the bottom of the blind a
14. ves 1 Unpack all the shelving items from inside the cabinet 2 Establish the desired position for each of the shelves based on the height of the product intended to go on each shelf 3 Fit the cantilevered shelf brackets into the vertical slots in the back of the cabinet Place each shelf onto the brackets with the rear of the shelf clipped over the back of both brackets Cantilevered The cantilevered shelf brackets can be fitted either horizontal so the Shelf Brackets shelves sit flat or angled down to accommodate the gravity feed of product Loading When loading the cabinet shelves with product Ensure all shelves are securely fitted m Allow air space around all packages etc for even cooling and efficient operation of the chiller m Leave an air space of at least 50mm 2 above packages etc on the top shelf m Do not allow products to overhang the front of the shelves as this will effect the air flow Do not exceed a maximum loading of 20kg per shelf Remove some product if the shelves are flexing or bending 6 Installation User Manual SKOPE OD400 2 Operation Automatic After the cabinet has been positioned in a suitable place plug it in and check Start Up the following activity Item Activity Refrigeration Unit The refrigeration unit evaporator and condenser fans should all operate continuously from the time the cabinet is plugged in This may be verified by listening for compressor switch
Download Pdf Manuals
Related Search