Brushless ESC's User Manual
Contents
1. motor rotation can be reversed by changing the value of setting on the ESC 9 Restore factory setup defaults Restore Sets the ESC back to factory default settings Tones Toot Toot toot Throttle range setting 1 Turn on transmitter move throttle stick to top position connect battery pack to ESC and iene 3 Short wait for 2 seconds until you hear toot toot emits 2 The tone of toot toot will repeat for 4 times during these times move the throttle stick to bottom position the motor emits special tones means the setting of throttle range is Battery Type MEd completed After 1 second the system will enter the battery cells confirmation program and Cutoff Mode emit 123 for system OK tones Cutoff Threshold Low Note In order to make ESC compatible with your transmitter s throttle range if you otor Timing Low use this ESC for the first time or if you change to use other transmitter you must reset R the throttle range by following above mentioned steps Very Soft Acceleration Program Setting Default Setting Program the ESC with your 2 Select programmable item transmitter 4 Steps After entering program mode you will hear 9 tones in a loop 1 Enter program mode with the following sequence If you move the throttle stick 2 Select programmable item to bottom and hear one group of special kind of tones the 3 Set item s value Programmable item will be selected option toot2. Very Soft Soft Acceleration Start Acceleration Start Acceleration mode is suitable for fixed wing Very Soft and Soft Acceleration suitable for Helicopter The initial rom for Very Soft and Soft Acceleration is relatively low even if the throttle stick is moved to the top position instantly the slow will be provided from start to full rom 7 Active RPM Fixed Wing Helicopter Note Rpm On There will be a 8 second delay from start to full rpm Attention After start up if throttle cut off in less than 3 second then the next start will be as Rpm off mode if throttle cut off in more than 3 seconds then the next star will be in Rpm on mode Once the governor Mode is enabled the ESC s Brake and Low Voltage Cutoff Type settings will automatically be reset to No Brake and Reduce Power 3 Set item value Programmable option respectively regardless of what settings they were previously set You will hear several tones in loop Set the value matching to a tone by moving throttle stick to 8 Motor Rotation Forward Reverse the top position when you hear the tone then a special tone emits means the value is set and In most cases motor rotation is usually reversed by swapping two motor wires saved Keeping the throttle stick at the top position you will go back to step 2 and you can However in cases where the motor cables have been directly soldered the ESC cables select other item Disconnect the battery pack will exit the program mode directly
3. www szfvt com Contac Email sales szfvt com Check the power connection Replace the connectors Check the voltage of battery pack or move the throttle sticker to the right position Change to use bigger discharge power battery Change to use low rotation motor Start up accelerate sets lower Changes to bigger motor timing Swap any two wire connections between ESC and motor
4. till he toot toot toot toot emits which means the program mode is entered Select Programmable Items Now you ll hear 9 tones in a loop When a Toot tone emits move throttle stick to bottom to enter the Start Mode Set Item Value Programmable Options Motor starts to ring afte you hear Toot toot move thel throttle stick to top position then a special tone emits which means youl have set the Brake type to the value lof Brake ON Trouble Shooting After power on motor does not work no sound is emitted After power on motor does not work such an alert tone emits beep beep beep beep beep beep The motor doesn t run smoothly or stop running while starting up sudden acceleration The motor runs in the opposite direction in condition of The connection between battery pack and ESC is not correct Throttle sticker is not on bottom position or input voltage is abnormal too high or too low Battery s power doesn t discharge well Motor rotation too high Start Up accelerate sets too high Motor timing too low The connection between ESC and the motor need to be changed Favourite Electronics Shenzhen Co Ltd Address 2 F Bldg 1 Henghaofeng S amp T Park Phase II E Block Mingzhu Industrial Zone Avenue Mingzhu Shajing Bao an Shengzhen P R China Tel 86 755 61168882 61168885 Fax 86 755 61168887 Website
5. Brushless ESC s User Manual DECLARATION Thanks for purchasing our SKY series Brushless Electronic Speed Controller ESC High power system for RC model can be very dangerous so please read this manual carefully In that we have no control over the use installation application or maintenance of our products no liability shall be assumed nor accepted for any damages losses of costs resulting from the use of the product Any claims arising from the operating failure of malfunctioning etc will be denied We assume no liability for personal injury property damage or consequential damages resulting from our product or our workmanship As far as is legally permitted the obligation for compensation is limited to the invoice amount of the product in question FEATURES All firmware and components are purchased from renowned makers Multiple motor timing choices so compatible with most brushless motor in the market Compatible with fixed wing and helicopter If the position of the throttle stick is inadequate when power on the motor will not start and emit Beep beep continuous warnings Multiple protection features Over heat protection and throttle signal loss protection low voltage cut off protection Throttle range setting and multiple accelerations start up choices Wires Connection Connectors should be soldered carefully to the cables and insulated with heat shrink tube to avoid shortcut SETTINGS Wo
6. brake 1 short 4 Exit program mode toot toot battery type 2 short 1 Enter Program Mode toot toot toot cutoff mode 3 short 1 Switch on transmitter movel toot toot toot toot cutoff threshold 4 short throttle stick to top position toot motor timing 1 long 2 Connet battery pack to ESC and gt toot toot startup 1 long 1short wait for 2 seconds toot toot toot governor 1 long 2 short 3 Motor emit 4 times of toot toot toot toot rotation 1 long 3 short toot tone which means progra toot toot toot toot toot default 1 long 4 short mode is entered 3 Set item value Programmable option You will hear several tones in loop Set the value matching to a tone by moving throttle stick to the top position when you hear the tone then a special tone emits means the value is set and saved Keeping the throttle stick at the top position you will go back to step 2 and you can select other item Disconnect the battery pack will exit the program mode directly Tones Beep Beep beep Battery Type Cutoff Mode Cutoff Threshold Startup Acceleration Motor Rotation Default Setting Program Example Setting Brake to Brake ON i e option 2 of the programmable item 1 Enter program mode switch o transmitter move throttle stick tol top position connect battery pack to SC then wait
7. rds in Bold Black are default settings 1 Brake ON OFF 2 Battery type NiMH LiPo 3 Low Voltage Cutoff Type Reduce Power Cut off Power Note When ESC is in low voltage or over heat to slowly reduce the motor power state no matter what the throttle sticker position is the power will reduce to a certain value to stabilize the system 4 Cut off Voltage Threshold Low Voltage Protection Threshold Low Medium High 1 For LI xx packs number of cells are automatically calculated This ESC provides 3 setting options for the low voltage protection threshold Low 2 8V Medium 3 0V High 3 2V For example the voltage cutoff options for a 3 cell Li Po pack would be 3 0x3 9V Medium 2 For Ni xx LiFe packs low Medium High cutoff voltages are 0 60 65 of the initial voltage of the battery pack 0 means no protection For example A fully charged 6 cell NiMh pack s voltage is 1 44Vx 6 8 64V when Medium cutoff voltage is set the cutoff voltage is 8 64V x 60 5 18V 5 Motor Timing Low Medium High In most cases low timing works well for all types of motors However the structure for motors are different please try to use different timing for a better effect For higher speed High timing can be set Some motors require different setups therefore we suggest you to follow the manufacturer recommended setup Note Run your motor on the ground first after making any changes to your motor timing 6 Soft Acceleration Startup Mode
Download Pdf Manuals
Related Search