PM-311 User Manual
Contents
1. 5 3 3 Webcam Launch icon to launch the Webcam utility 5 3 4 Monitor Switch For Monitor switch press the Monitor Switch display mode within following four options Duplicate W e You can click Duplicate to display the same contents both on the PM 311 screen and external display device The resolution on these two display modes are same it is not available to adjust the resolution on the external display mode 32 PM 311 User Manual e You can click Extend BEES to display the different contents on the PM 311 screen and external display device You only can adjust the resolution on the external display device e You can click Projector only to display on external projector only 5 3 5 RF Device ON OFF Control Press this soft button via hotkey utility menu to enable or disable Wi Fi Bluetooth WWAN or GPS devices When you press the RF ON OFF soft button the screen pops up the option list for your selection W WP Bluetooth M GPS You can see all functions in this option list have been ticked To close any device function please touch the option to close the execution as shown in the following graphics Disable WWAN function Disable GPS function To activate the function please again tick the option as shown in the following graphics to make the device enable 33 PM 311 User Manual Activate WWAN function Activate GPS function 34 PM 311 User Manual Cha2. PM 311 User s Manual Hie e PM 311 User Manual Introduction 1 2 Please read these safety instructions carefully Please keep this User s Manual for later reference Please disconnect this eguipment from connecter before cleaning Don t use liguid or prayed detergent for cleaning User moisture sheet or cloth for cleaning Make sure the equipments are connected to the power source with the correct voltage frequency and ampere All cautions and warnings on the equipment should be noted Never pour any liquid into opening this could cause fire or electrical shock Never open the equipment For safety reason the equipment should only be opened by qualified service personnel If one of the following situations arises get the equipment checked by a service personnel a Liquid has penetrated into the equipment b The equipment has been exposed to moisture c The equipment has not worked well or you cannot get it work according to user manual d The equipment has dropped and damaged If the equipment has obvious sign of breakage Caution on use of battery User the battery recommended by the manufacturer or the same type of battery installed by the manufacturer If incorrect battery is used 1 PM 311 User Manual it may cause explosion or fire hazard Recycle or discard used batteries according the manufacturer s instruction or your local authority 10 The computers use nonvolatile memory
3. Mechanical Shock e Operating 20g 11ms Terminal sawtooth e Non operating 40g 11ms Terminal sawtooth MIL STD 810G Method 516 6 Procedure Water Dust Resistance IP65 equivalent 1 2 6 Material Chassis e RuggedTablet PC Slate Enclosure e PC ABS Plastic PC ABS and TPU Double Injection with Protective Rubber Grips Set Dimension W x Hx D mm e 220 X 168 x 26 5mm Weight e Approximate 950g with internal battery 1 2 7 Operation OS WIN7 PRO WES7 WS7P 1 2 8 Certifications EMI e FCC part 15 Class B e CE EN55022 EN55024 Safety e UL EN60950 CE RF e FCC part 15 subpart C SAR e FCC SAR OET 65 C 10 PM 311 User Manual 1 2 9 Optional Internal Module e 3 5G Sierra MC8355 Gobi3000 e Protocol HSUPA HSDPA UMTS EVDO EDGE e Frequency UMTS HSUPA HSDPA 850 900 1800 2100MHz CDMA EVDO 800 1900MHz GSM GPRS EDGS 850 900 1800 1900MHz 1 2 10 Optional External Accessories e MSR and Barcode Snap on module e MSR Reference Standard ANSI ISO Standards 7810 7811 1 6 7813 JIS Il Decoding Method ISO Track1 IATA Track2 ABA and Track3 THRIFT e Barcode Decoded Mode 1D Symbologies EAN UPC RSS Code 39 Code 128 UCC EAN 128 ISBN ISBT Interleaved Matrix Industrial and Standard 2 of 5 Codabar Code 93 93i Code 11 MSI Plessey Telepen postal codes 2D Symbologies Data Matrix PDF417 Micro PDF 417 Maxicode QR Aztec EAN UCC com
4. and the touch screen operation 3 2 Using the USB Ports USB Universal Serial Bus is a hardware interface that enables you to connect multiple devices such as printers mice keyboards storage devices joysticks digital cameras and video conference cameras etc to your tablet pc and up to 127 devices can be attached Besides USB s hot swap capability allows everything to be plugged in and unplugged without turning the system off USB 2 0 is fully backward compatible you will be able to use an USB 1 1 device in an USB 2 0 compliant system 1 Connect the external device to the system 2 The USB ports support hot plug in connections Install the device driver before using the device 3 3 Using the External Audio System At the right side of your Tablet PC you will find the built in audio ports for connecting Microphone jacks earphone or powered speaker To connect to an audio jack 1 Locate the audio ports Microphone and Headphone that you want to use to the target device 2 Plug the jack into the port on the right side of the system 3 4 Installing the Battery optional PM 311 provides optional external battery to extend the power of your system For installing the battery pack please follow the steps below 1 Turn off the system 2 Align the hook wall at the rear side then place and screw it securely 19 PM 311 User Manual Step1 Step 2 Step 3 3 Remove the cover of the external battery conn
5. gt LCD Panel 7 inches LED Backlight Screen 7 XGA 1280x800 350nits LCD or 700nits LCD option gt Touch Panel 8 PM 311 User Manual 5 wire Resistive Touch Screen Audio 1 x High Quality Speaker 2W Internal Microphone 1 x in front Bezel Communication 10 100Mbps Ethernet Wi Fi IEEE 802 11 a b g n Bluetooth 4 0 Webcam Front 2 Mega pixel Camera Rear 5 Mega pixel Camera with LED Flash light 1 2 2 VO Interface e External UO e 2 x USB 2 0 type A 1x MicroSD slot e 1x RS232 LED Status Indicator e Power LED Status 1 x Green Red Colors e Storage LED Status 1 x Blue Color e Wi Fi LED Status 1 x Blue Color 1 2 3 In Front Control e Switch e 1 x Power Button Button e Program Function Buttons 6 x Function keys Programmable 1 2 4 Power Management e Power Adapter e AC to DC 19VDC 3 42A 65W e AC 100V 240V 50 60Hz input e 19 DC in e Battery Internal Battery e Internal Smart Lithium Polymer Battery 3000mAh 2S1P 7 4V 1 2 5 Environment e Operation Temperature e 10 C to 50 C MIL STD 810G Method 501 5 and 502 5 e Storage Temperature e 20 C to 70 C MIL STD 810G Method 501 5 and 502 5 e Humidity 9 PM 311 User Manual e 5 95 without condensation MIL STD 810G Method 507 5 Drop e 5 ft drop to Plywood MIL STD 810G Method 516 6 Procedure IV Vibration e Operating SSD MIL STD 810G Method 514 6 Category 4 Fig 514 6C 3
6. screen or allow excess liquid to drip down inside the device Do not place anything such as food and drink on the screen at any time to prevent damage to the screen Clean the LCD display only with a soft cloth dampened with denatured alcohol or a proprietary LCD screen cleaner Cleaning the PM 311 Turn off the PM 311 and unplug the power cord Wipe the screen and exterior with a soft damp cloth moistened only with water Do not use liquid or aerosol cleaners on the screen as these will discolor the finish and damage the screen 35
7. selecting Enabled or Disabled option e Boot Priority lets you set the boot priority from UEFI boot or HDD boot 4 3 Security Chip Configuration Set Supervisor Password 25 PM 311 User Manual e Supervisor Password is This option displays the status of Supervisor Password If the password is entered it will display Set information or it will display Cleared information when there is no password setting e User Password is this option displays the status of User Password If the password is entered it will display Set information or it will display Cleared information when there is no password setting e Set Supervisor Password this field let you set or clear the Supervisor account s password e Set User Password this field let you set or clear the User account s password e TPM Support lets you activate or close the TPM function by selecting Enabled or Disabled option For the non TPM SKU this item will display no detected 4 4 Boot Management Setup 1 USB HDD This page allows you to set the search drive sequence where the system will try to boot up first To select the boot device you can use the up or down arrow key then press lt gt to move up the device in the list or press lt gt to move down the device in the list To exit from this menu press lt Esc gt 26 PM 311 User Manual 4 5 Exit Control Exit Saving Changes e Exit Saving Chan
8. that requires a battery to retain system information when power is removed The 3V lithium battery is on the system board The battery life depends on the amount of time the computer is powered on If the computer does not display the correct time and date replace the battery IMPORTANT Loss of BIOS settings occurs when the battery is removed BIOS settings must be reconfigured whenever the battery is replaced WARNING A risk of fire and chemical burn exists if the battery is not handled properly Do not disassemble crush puncture or short external contacts or expose the battery to temperatures higher than 60 C 140 F Do not dispose of a used battery in water or fire CAUTION Danger of explosion if battery is incorrectly replaced Replace only with same or equivalent type recommended by the manufacturer Discard used batteries according to the manufacturer s instructions FCC Compliance Statement This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation I
9. 2 osk exe F3_PARA F3_PATH F4_EXE C WINDOWS system32 taskmgr exe F4_PARA F4_PATH The configuration file is c FKeySet txt e Camera 5Mega pixel The built in camera can be used as a communication device for allowing you to capture images record videos and have video chats It is 5 0 M pixels and transmitting instant image through network for conference Power Button Switch the computer power on and off or resumes whenever it is in Suspend mode by OS define e USB Ports The two USB type A ports allows you to connect USB 2 0 compliant devices for example mouse keyboard and so on to your Tablet PC e 3 5mm Headphone Jack Allows you to connect an external 3 5mm 4 conductor TRRS stereo plus mic headphone for personal listening and sound recording e MicroSD Card Slot The MicroSD SDHC card slot allows you to transfer record video and pictures to your tablet while adding extra storage capacity e Ethernet Port 15 PM 311 User Manual The 10 100Mbps Ethernet port allows you to connect to other computers networks through a local area network LAN e RS 232 Serial Port RS 232 serial port allows connections to modems printers mice barcode readers data acquisition equipment and other peripheral devices e Accessory Door By removing the two long screws on top side of the system allows you to install optional snap on module e External Battery Connector To install the external battery
10. C adapter e Docking Connector Lets you connect the system to docking station to dock the tablet PC when you are at home or office desk 16 PM 311 User Manual 2 2 Preparing for Installation Your PM 311 is designed and pre configured for easy setup and use This section describes the installation steps you should follow to get the system running as quickly as possible 2 2 1 Switch ON the main battery a Main battery switch is located on rear side of yellow label battery door b Adjust DIP switch to ON c Place back the battery door ip WE HL HE sf de 2 2 2 Plugging to the DC supply The AC adapter provides external power source to your system and charges the internal battery pack at the same time The AC adapter also has an auto switching design that can connect to any 100VAC 240VAC power outlets To connect the power adapter 3 Plug the AC adapter connector to the DC Jack socket on the left side of the system 4 Plug the power cord to the AC adapter H o 5 Plug the other end of the power cord to a live wall outlet at the same time the Power LED at front panel lights up For the power supply of this equipment an approved power cord has 17 PM 311 User Manual to be used Make sure the socket and any extension cord s you use can support the total current load of all the connected devices Remove all power from the device prior to installing or removing any a
11. E Ee Ge 33 CHAU CEG NE E EE OE EE EE EE 35 Ee e Ee TE 35 6 1 Maintaining the Batter ees ke RR RR EER ERK RE ER RR KEER RR KEER ERK KEER RR KEER EE 35 6 2 Maintaining the LCD DisplaY sees REK RR EE RR RR EE RR RR RE ERK KEER R RR EER EE 35 6 3 Cleaning the PM 311 essens de ARK KA ne EER Ee ERNA ee nna 35 7 PM 311 User Manual Chapter 7 General Information 1 1 Introduction PM 311 rugged tablet PC is Intel Cedar Trail Platform N2600 NM10 processor core architecture based rugged Tablet PC with a bright 7 inch LED backlight LCD display The powerful CPU brings the most dynamic applications to life without sacrifices to any industrial reliability Delivering a variety of connectivity features built in USBs Microphone and Headphone port It is ideal for an all around system performance Furthermore PM 311 rugged tablet PC is equipped with fanless design 1 2 Specification The PM 311 rugged tablet PC is a flexible multi functional flat tablet PC With following specifications that can be applied in diverse operational environments and implemented in multi faceted applications 1 2 1 Main System gt Platform Intel Cedar Trail Platform N2600 NM10 gt CPU Intel ATOM N2600 1 6GHz Dual core gt Graphic Intel Graphics Media Accelerator 3600 series gt Chipset Intel NM10 Express Chipset gt System Memory 2GB DDRIII 800 SO DIMM gt Storage 1 x 32GB SATA Slim Half Size Solid State Disk
12. PM 311 I O is as described below VO Diagram MSR Barcode Scanner Function Button Function Button 2 Mega pixel Camera GPS 5 Mega pixel Camera Power Button USB Audio Jack Micro SD DC IN Docking Connector F1 Button F1 Windows File explorer F2 Button F2 Windows Media Player RJ45 RS232 Enter Button Finger Print LED Indicator F3 Button F3 On Screen keyboard osk Ne F4 Button F4 Task Manager 13 PM 311 User Manual Fn Hotkey Utility Enter or Return key Implement Secure Attention Sequence SAS similar function as pressing Ctrl Alt Delete combination keys F1 or F4 acts as trigger button when optional barcode scanner is installed e Camera 2 Mega pixel The built in camera can be used as a communication device for allowing you to capture images record videos and have video chats It is 2M pixels and transmitting instant image through network for conference e Digital Microphone The built in microphone receives sounds and voices when used with the built in camera e LED Power Storage Wi Fi Keeps you informed of your system s current power status Storage access status and Wi Fi ON OFF status d O l 1 Power Indicator LED 2 Storage Access 3 WiFi ON OFF e Power Indicator LED To let you know that system is turned on and indicate the battery charging status lt Lights green when the system is powered on and battery is discharging o
13. To display the User Interface please press the FN button or point the hot key Utility on the screen D To close the User Interface function please press the button on the top right corner on this User Interface for disabling this utility from the screen If there is no action took for this utility in 5 seconds the UI screen will close automatically 5 2 3 System Status Information This utility shows you the battery capacity status RF status with its signal strength and system information and provides the control panel for the function setting 28 PM 311 User Manual For battery capacity status The PM 311 is eduipped with one internal battery and one optional external battery The battery capacity status shown below advises you that only one internal battery is embedded with the system which is fully charged and there is no SE optional battery installed in the system If the system installs both the 1st internal battery and 2nd optional battery the illustration shown below indicates its current charging status and capacity If Ist battery capacity drops to 15 the system will display the following warning message for 5 seconds For RF status The following RF status shows you that the system is equipped with Wi Fi and Bluetooth functions If you want to close either of these functions please refer section for how to disable it 29 PM 311 User Manual M WP Bluetooth The following si
14. ccessories hardware or cables Before cleaning the system make sure it is disconnected from any external power supplies i e AC adapter 2 2 3 Starting Your System The Power Resume button is found on the right side of the Tablet PC Press the Power Resume button to start your system and check that if the Power LED turns on After a few seconds the system s display will turn on and your system will begin to execute the Power on Self Test or POST to check if all system components are running properly Any error found during the test will be displayed on the screen After the test the screen will also display a message press lt F2 gt to enter SETUP You don t need to run this program at the moment as your dealer already made the necessary settings for your computer optimal operation After the test has completed your computer will start to search and boot up the operating system from your hard drive 2 2 4 Connecting the keyboard and mouse Before setting up the system please make sure the following items are available e Keyboard e Mouse for system software installation A keyboard is an input device a mouse is a pointing device Please connect these two devices as graphics shown below to interact with your system 18 PM 311 User Manual Chapter 3 Using the PM 311 3 1 Introduction This chapter describes the basic features and procedures for using the panel PC It includes the I O ports connecting
15. ce and screw it firmly of the system 3 5 2 Removing a SIM Card To remove a SIM Card from the SIM Card slot 1 Turn off your system 2 Slightly push the SIM card to pop it out and pull it out directly When the SIM card has moved out a space out of the slot hold the edges of the card and slowly slide it out 3 6 Using a 2 in 1 Snap on MODULE Barcode Scanner MSR optional Your PM 311 is designed with equipped the optional 2 in 1 Snap On MODULE Barcode Scanner MSR To install the 2 in 1 Snap on MODULE Barcode Scanner MSR 1 Make sure the system is turned off 2 Unscrew the compartment cover on top of the system 3 Place module connector to the connectors inside the compartment 21 PM 311 User Manual 4 Screw to secure the Barcode Scanner module onto the system 22 PM 311 User Manual Chapter 4 The BIOS Setup Program This system comes with a chip from Phoenix BIOS that contains the ROM Setup information for your system This chip serves as an interface between the processor and the rest of the system components This section explains the information contained in the Setup program and tells you how to modify the settings according to your system configuration The Setup utility program allows updates to the main board configuration settings The BIOS setup values will be saved in the CMOS It is executed when you change the system configuration you change the system back
16. ector as marked Oo below and place it on the lower position as marked below 4 Snap the battery pack into the external battery connector and latch into the hook wall securely Step 4 Step 5 For removing the external battery repeat the above steps in reverse order to remove the battery 3 5 Using a SIM Card Your PM 311 can be equipped with a 3 5G module optional that can work with SIM card SIM card is always working with 3 5G module 3 5 1 Inserting a SIM Card To insert a SIM card into the SIM Card slot 1 Turn off your System The PM 311 must be powered off while the SIM Card is being connected Otherwise it is harmful to both devices and it shortens the life of these devices 3 Make sure the clipped corner facing inward with the metallic label of the card facing down Push the SIM Card firmly but slowly into the SIM Card slot To insert a SIM card into the slot please pay attention only one correct side can be accepted for the card slot If you cannot insert the 20 PM 311 User Manual card into the slot or you had inserted the card but it is not recognized by the Tablet PC please remove the card and insert it again To prevent the damage made both on card and the slot never forced an entry into the slot with incorrect side 4 When the full length of the card is almost inside the slot the SIM Card will be automatically detected 5 Place the both battery and service door cover back to the pla
17. f this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment 2 PM 311 User Manual FCC RF Radiation Exposure Statement 1 This Transmitter has been demonstrated co location compliance requirements with Wi Fi Bluetooth and RFID Modules This transmitter must not be co located or operating in conjunction with any other antenna or transmitter 2 This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This device was tested for typical hand held operations with the device contacted directly to the human body to the back side of the tablet pc To maintain compliance with FCC RF exposure compliance requirements avoid direct contact to the transmitting antenna during transmitting Europe EU Declaration of Conformity This device complies with the essential requiremen
18. ges when you select this option it will pop out the following message Save configuration changes and exit setup Select OK to save the changes and exit the BIOS SETUP UTILITY e Exit Discarding Changes when you select this option it will pop out the following message Discard changes and exit setup Select OK to exit the BIOS SETUP UTILITY without saving any changes e Load Setup Defaults when you select this option it will pop out the following message Load optimal defaults Select OK to load the default values for all the setup configurations e Save Changes when you select this option it will pop out the following message Save changes Select OK to save all changes 27 PM 311 User Manual Chapter 5 User Interface for PM 311 5 1 Introduction This user interface provides specific mobile utility to let you easily setup some helpful functions and aware the system status directly This utility also let you adjust some function to fit the requirements such as brightness and volume adjustment webcam launch screen orientation and monitor switching Furthermore it also provides system information for your reference such as battery status RF setting with its signal strength firmware BIOS amp EC version information Besides these features you can press the soft button to hibernate this device 5 2 About the User Interface 5 2 1 Enable or disable the User Interface
19. gnal strength shows you that the Wi Fi function is connecting currently the stronger the signal strength the more scale will show on the bar If there is no module in the system there will be no status scale in the following status bar For System Information The system information shown on the left shows you the hotkey utility version BIOS and EC version and you can use them for customer service when asked system Info Utility 1 0 0 8 BIOS ITBE2D_D EC 1911 30 PM 311 User Manual 5 3 Using the Application Your PM 311 has numbers of applications on the control panel for executing specific command It provides you to adjust brightness volume launch webcam make screen orientation and switch monitor 5 3 1 Brightness Control For brightness adjustment press the Brightness command e You can click DO or KA to reduce or increase the brightness e Also you can slide the scale bar to set the brightness e Since the system supports the light sensor if you tick the brightness Auto adjustment the screen brightness will automatically adjust according to the operating environment 5 3 2 Volume Control When you press it the Volume control panel is appeared as follows 31 PM 311 User Manual e You can click Q or el to reduce or increase the audio volume incrementally e Also you can slide the scale bar to set the audio volume e You can tick the Mute to mute the audio
20. pack install external battery holder first and remove the cover of external battery connector before snap the battery pack into the external battery connector e Speaker Integrated stereo speaker for sound and audio output for your multimedia presentations or listening pleasure Protective Rubber To prevent system harm from vibration or shock the system is designed with installing protective rubber on four corners DC Jack Lets you connect the AC power adapter in supplying continuous power to your Tablet PC and recharging the battery The AC adapter provides external power source to your system and charges the internal battery pack at the same time The AC adapter also has an auto switching design that can connect to any 100VAC 240VAC power outlets To connect the power adapter 1 Plug the AC adapter connector to the DC Jack socket on the right side of the system 2 Plug the power cord to the AC adapter Plug the other end of the power cord to a live wall outlet at the same time the Power LED at front panel lights up For the power supply of this equipment an approved power cord has to be used Make sure the socket and any extension cord s you use can support the total current load of all the connected devices Remove all power from the device prior to installing or removing any accessories hardware or cables Before cleaning the system make sure it is disconnected from any external power supplies i e A
21. posite Desktop Docking e 4x USB2 0 type A 1 x Ethernet 1 x HDMI 1 x VGA 1 x Kensington lock and 1 x DC Jack support External Battery Kits e External Battery Pack Hot swappable Lithium Polymer battery pack doubles duration of mobile operation 4200mAh 2S1P 7 4V External Battery Charger a Recharges external battery pack e Vehicle Application Accessories Vehicle Mounting Docking 4 x USB2 0 type A 2 x RS232 1 x 10 100Mbps Ethernet 1 x VGA and DC Jack support 75 x 75 100 x 100mm Vesa Mount Holes support 6VDC to 36VDC Input 6VDC to 36VDC for Momentary and 9VDC to 32VDC for Normal 19 V 1 57A Max total output 30W 11 PM 311 User Manual Cigarette lighter plug power cord ACC power cord option GPS option 1 3 Packing List Main Packing List QTY i AR Main system stylus Comer Rubber Power Adapter Hand Strap E Rubber Screw Handle Secures Shoulder Strap 1 Accessories Option an Barcode Scanner MSR Battery Charger DeskTop Dock EE HE Ek Dock 1 External EE Pack vehicle Power es Battery Chargen Charger 1 12 PM 311 User Manual Chapter 2 System Setup 2 1 Exploring Your PM 311 Before starting to set up the PM 311 get familiar with the locations and purpose of controls connectors and VO ports which are illustrated in the figures below When placed upright the front panel of the PM 311 appears as shown in below 2 1 1 The PM 311 IO The
22. pter 6 Maintenance Your PM 311 needs occasional cleaning to prolong their life Please read this section carefully to ensure proper care of PM 311 When it is necessary to clean it use a soft lint free cloth slightly dampened with a mild detergent solution or use the contents of any commercially available computer cleaning kit Never use petroleum based solvents or harsh detergents to clean the system Also never spray any liquids directly on the computer case or screen If the display screen has become smeared or dusty clean the screen by first applying a mild glass cleaner to a soft clean lint free cloth and gently wipe the glass Never apply liquids directly on the screen surface Moreover do not use paper towels to clean the display screen 6 1 GU No Paper can scratch the display screen matte Maintaining the Battery Do not expose heat or attempt to disassemble the battery and do not place the battery in water or ina fire Do not subject the battery to strong impact such as a blow from a hammer or stepping on or dropping it Do not puncture or disassemble the battery Do not attempt to open or service the battery Replace only with batteries designed specifically for this product Keep the battery out of reach of children Dispose of used batteries according to local regulations Maintaining the LCD Display Do not scratch the surface of the screen with any hard objects Do not spray liquid directly on the
23. r when the system is powered on and battery is fully charged lt Lights blinking red when the system is in S3 Suspend and battery is charging or when the system is in S3 Suspend and battery is fully charged lt Lights red when the system is powered on and battery is charging lt Lights blinking red indicates that the battery is in charging and system is power off S3 Suspend lt Lights off when power off or the battery is fully charged e Storage Access When LED in blue light indicates that the system is accessing the Storage Drive 14 PM 311 User Manual e WiFi ON OFF When LED turns on blue light indicates that the WiFi is activated When LED lights off it indicates that the WiFi function is disabled e User Interface Button This button is used to define the User Interface function When you press this button the system will appear the UI screen as illustrated below for executing the applications easily and quickly e Programmable Function Buttons If your system does not define this button s function this button can be programmable to execute specific application When you program your application please write this directory as listed below into your configuration file then the system will aware and execute this application Setup FI EXE c windows explorer exe Fi PARA F1 PATH F2 EXE C Program Files Windows Media Player wmplayer exe F2 PARA prefetch 1 F2_PATH F3_EXE C WINDOWS system3
24. rmation the end user should contact the national spectrum authority in France 4 PM 311 User Manual Table of Contents INI OO UCU ss ED N ee di GE 1 Table Of E d 5 CHEADICE FT AE EE EE 8 General Information ss NENNEN ER EE ER EE RE 8 Dec Ws WMT ONC e p D 8 ES sade Uile EE EE Ra 8 MAR ES Ou E 8 EA OS os ONE EE EE EE EE N 9 1 2 3 WE PION CODO see ees ee Re ei N Ao ge ee 9 1 2 4 Power Management 9 Ba od as ie pd EE EE OE OE EER NE EE 9 Le D EO EE EE ER EE E EE LE ORE 10 1 2 7 Opaal on OS ese Rae EA ee RE nate ae n AE ee SE ER ince EE 10 128C CAUNES ie ae De oe be ee ee OE De 10 1 2 9 Optional Internal Module iii ee ee ee ee ee Ee ee ee ee 11 1 2 10 Optional External Accessories ee ee ee ee ee ee 11 UN sie died NE EE e R 12 EE 13 System e iss DE ER Ee EE OE EE EI EE 13 2 1 Exploring Your PM TI ees Rede ER GED ie GE GR N bee GE ER ee 13 Bk TERM OD EE 13 2 2 Preparing for InstallatlOn iese ee EER RE ERK EE ER REGEER KEER RR Re ERK EER ER KEER EE 17 2 2 1 Switch ON the main Daller 17 222 Plugging to th DC SUDD so ERGE RES Ee Ge Ee N ee Ge 17 2 2 3 Slarting Your System eie ee ee Ee ee ee RE ee ee ee ee ee ee ee ee ee ee ee 18 5 PM 311 User Manual 2 2 4 Connecting the keyboard and MOUSE ie AR Re ARE 18 Go eo dade OE EE EE OE EE EE EN 19 Using the PM 311 ss EES EE EE 19 2 Bled dee te die ie AE OE OE N EE EE EE 19 3 2 Using the USB e CC 19 3 3 Using the External Audio Sys
25. rsion Build Time the system will automatically displays the build time of BIOS EC Version the system will automatically displays the information of EC Embedded Controller firmware version VBIOS Version the system will automatically displays the information of VBIOS version of internal graphics Board Version The system will automatically displays the information of PCB version of mainboard Processor Type The system will automatically displays the information of Processor Type and speed System Memory Speed The system will automatically displays the information of System Memory Speed L2 Cache RAM the system will automatically displays the information of L2 Cache RAM Total Memory the system will automatically displays the information of Total Memory 24 PM 311 User Manual 4 2 Advanced BIOS Features For Advanced Settings the BIOS will automatically display the Platform information and let you define the configuration when system booting In this section you may set the configurations for the following items Quick boot UEFI boot Legacy boot and Boot Priority SATA Controller Mode e Select Language lets you select the language displayed in SETUP UTILITY The current BIOS support the languages of English Japanese and French e UEFI Boot lets you activate or close the UEFI boot function by selecting Enabled or Disabled option e Legacy Boot lets you activate or close the Legacy boot function by
26. teM seeks RR ee EER RR EE EER RR Rae EE EE 19 3 4 Installing the Battery Optional is Re ER RE EER EE RR EER ERK EER ER KEER 19 3 5 Using a SIM ad ss ai EER ARE ER EI AA HE EER Re Ge ee ee oi 20 3 5 1 Inserting a SIM Card ese SN EE EE AN AE EE GR RA ED SE Ee Ee Re EE ESE 20 3 5 2 Removing a SIM Card sms Eie NG Ek Ee GR EG N GE DR EE ee 21 3 6 Using a 2 in 1 Snap On MODULE Barcode Scanner MSR optional 21 Og 2 0 ge En EE ee ee EE ee eee eee eee 23 The BIOS Setup Program ss ss EER EE RE ER EE 23 4 1 Main Screen Setup Utility iese koe RR EE EER RR RE EER RR REGEER RR RR Rae EE EE 23 4 2 Advanced BIOS Features seke Re Re Re Re REENEN EN ee ER EG Re Re Re Re Ee 25 4 3 Security Chip Configuration ccccccccsssssseseeeessseessesseeeeeeseeeeeneees 25 4 4 Boot Management Setup ccccceeceessseeeeeeeesseeeseeenseeeeseeenseeesseoenes 26 4 5 Exit Control EE 27 Call DEENSE EE E SE ee 28 User Interface fOr PM 311 EE ENNEN ENNEN 28 G ER 28 5 2 About the User Interface ek ENKEN Re Re Re REENEN Re ee Re Re Re Re Re Re Ee 28 5 2 1 Enable or disable the User Interface ES ee ee ee ee 28 5 2 3 System Status Information 28 5 4 E eh CR e e Uu ME EN e edel e EE 31 5 32 Volume Control use die ee RE ha ee de eias 31 5 8 WebEam Ee es RES AE ER Ee GE ee AEAEE diodia 32 5 3 4 Monitor Switch 32 6 PM 311 User Manual 3 9 AF Device ONOFF CONVO issie ses RS se ee SG EE ee D
27. ts of the R amp TTE Directive 1999 5 EC and EMC directive 2004 108 EC The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R amp TTE Directive 1999 5 EC and EMC directive 2004 108 EC EN 55022 2006 A1 2007 EN 61000 3 2 2006 EN 61000 3 3 1995 Al 2001 A2 2005 EN 55024 1998 A1 2001 A2 2003 IEC 61000 4 2 2008 IEC 61000 4 3 2006 A1 2007 IEC 61000 4 4 2004 IEC 61000 4 5 2005 IEC 61000 4 6 2003 A1 2004 A2 2006 IEC 61000 4 8 1993 A1 2000 IEC 61000 4 11 2004 lt EN 60950 1 2001 Safety of information technology equipment lt EN 300 328 V1 7 1 2006 lt EN 301 489 17 V2 1 1 2009 and EN 301 489 1 V1 8 1 2008 lt EN 62311 2008 This device is a 2 4GHz wideband transmission system transceiver intended for use in all EU member states and EFTA countries under the following conditions and or with the following restrictions A A NA A lt In Italy the end user should apply for a license at the national spectrum authorities 3 PM 311 User Manual in order to obtain authorization to use the device for setting up outdoor radio links and or for supplying public access to telecommunications and or network services This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 2483 5 MHz For detailed info
28. up battery or the system detects a configuration error and asks you to run the Setup program You must have connected a USB type of keyboard and Use the arrow keys to select and press Enter to run the selected program Function Key Please check the following table for the function description of each direction key Moves cursor left or right to select menu on menu bar Moves cursor up or down to select items To change option for the selected items 4 1 Main Screen Setup Utility When you enter the BIOS SETUP UTILITY the Main screen will appear and display the system overview 23 PM 311 User Manual BS GE GE Kee Ee We at ee ee Sen FR TEER ae f gt System Date The Standard CMOS Setup screen is displayed above Each feature may have one or more option settings Use the arrow keys to highlight the feature you want to change and then use N or N to select the value you want for that feature NOTE The system BIOS automatically detects EC version board version Processor memory size thus no changes are necessary System Date to set the date highlight the Date field and then press keys to set the current date Follow the month day and year format System Time to set the time highlight the Time field and then press keys to set the current time Follow the hour minute and second format BIOS Version the system will automatically displays the information of BIOS ve
Download Pdf Manuals
Related Search