TruVision Dome Brackets Installation Manual
Contents
1. TruVision Dome Brackets Installation Manual Pendant mount installation TVD PPB Check the section Overview Fixed dome cameras by bracket on page16 to confirm that the correct bracket is used with the camera 5 inch dome cameras Use the TVD PPB bracket and the TVD CB5 TVD CB5A cup base See Bracket and cup base description on page 2 for examples of the assembled brackets To mount a pendant mount bracket on a ceiling 1 10 Screw the mounting plate onto the tube and fasten with the locking screw Pull the camera cables through the bracket tube and then attach the bracket to the ceiling with expansion screws Screw the cup base onto the tube and fasten with the locking screw TVD CB5 only Using the enclosed screws attach the camera housing to the cup base Loosen the screws on the dome enclosure 1 using the supplied hex wrench and remove the dome enclosure and liner 2 W i HE 1 TruVision Dome Brackets Installation Manual Connect the cables to the dome camera Insert the dome module into the cup base 8 Re attach the dome liner and enclosure to the camera 3 inch dome cameras Use the TVD PPB bracket and the TVD CB3 cup base See Bracket and cup base description on page 2 for examples of the assembled bracket To mount a pendant mount bracket on a ceiling 1 Screw the mounting plate onto the tube and fasten with the l2. TVD SNB bracket with the TVD CB3 cup base or TVD M2 WM bracket See Bracket and cup base description on page 2 for examples of the assembled brackets To mount a swan neck bracket on a wall 1 Pull the camera cables through the TVD SNB bracket tube and then attach the swan neck bracket to the wall with the expansion screws A provided Screw the cup base onto the swan neck bracket and fasten with the locking screw as shown A Then attach the mounting plate B to the cup base Note The mounting plate is shipped with the dome camera Loosen the screws on the dome enclosure using hex wrench and remove the dome enclosure and the liner Connect the cables to the dome camera Using the enclosed screws attach the dome module of the camera A to the bracket Then re attach the dome liner and enclosure B Re attach the dome enclosure to the camera TruVision Dome Brackets Installation Manual To mount an indoor wall mount bracket 1 Pull the camera cables through the TVD M2 WM 4ga bracket tube and then attach the bracket to the wall with the expansion screws A provided Ta O Attach the mounting plate to the bracket Note The mounting plate is shipped with the lt dome camera Loosen the screws on the dome enclosure using the supplied hex wrench and remove the dome enclosure and liner from the dome module Connect the cables to the dome camera Using the encl
3. A 13 Specifications 14 Pipe threading information 15 Overview Fixed dome cameras by bracket 16 TruVision Dome Brackets Installation Manual Introduction These are the installation instructions for the TruVision series of dome brackets and cup bases The series brackets and cup bases are compatible with both indoor and outdoor Interlogix cameras Models For a list of the brackets and cup bases with their corresponding cameras see Overview Fixed dome cameras by bracket on page on page 16 Packet contents The package contains the following items e Bracket or cup base e Accessories for installation e Screws Unpacking Please check the package contents to ensure that all parts are present and in good condition Note For safety purposes the mounting surface must be able to support three times the combined weight of the bracket cup base and camera Bracket and cup base descriptions TruVision dome swan neck bracket TVD SNB 180mm gt G1 1 84 Mounting plate 85 mm 150 mm 20 mm lt gt a Tube Y NO rro gt 2 TruVision Dome Brackets Installation Manual TruVision flush mount bracket TVD M2 FM 178mm E TruVision dome cup bases TVD CB5 160 mm Note The rubber ring for TVD CB5 is pre installed in the cup base TVD CB5A di 100 mm 160 mm Note The rubber ring for TVD CB5A is pre installed in the cup base TruV
4. amera to the pole mount 4 Adjust the camera position and angle as required Specifications SKU TVD SNB TVD PPB TVD M2 FM TVD M PMA TVD M2 WEBM TVD M2 WM TVD CB5 TVD CB5A TVD CB3 14 Dimensions 253 x 95 x 180 mm 150 x 537 mm 210 x 9 mm 117 x 194 x 143 mm 1135 x 9 mm 0135 x 182 5 x 251 mm 160 x 80 mm 160 x 100 mm 140 x 60 mm Weight 490 g 1 2 Ib 1169 g 2 56 Ib 540 g 1 19 Ib 1205 g 2 66 Ib 25 g 0 05 Ib 580 g 1 28 Ib 490 g 1 2 Ib 340 g 0 75 Ib 320 g 0 71 Ib TruVision Dome Brackets Installation Manual TVD CB2 124 x 57 mm 190 g 0 42 Ib Pipe threading information Pipe Threads Pitch Thread major Corresponding pipe thread lin mm diameter size mm in OD OD Thickness mm in mm G1 2 309 33 249 1 309 25 TruVision Dome Brackets Installation Manual Tapping drill size mm BSP F G 30 75 15 Ienue UO e 8 SU SI9ADBJG BWOG UOISIAN L 91 gt BE e gt P II zl gt j ER 1 sl gt ES gt Il PS IL gt ES w gt ES ww gt Il P e gt P gt ww gt O 1 gt j o Il O IO IE gt O gt Il BE eej gt P gt ws m
5. base plate to the converter pan 6 Re attach the camera enclosure to the camera Pole mount installation TVD M PMA Check the section Overview Fixed dome cameras by bracket on page16 to confirm that the correct bracket is used with the camera Use the TVD M PMA pole mount adaptor to mount a camera on a pole To mount a swan neck bracket on a pole 1 Atthe desired mounting place securely fasten the TVD M PMA pole mount adaptor to the pole Pull the cables through the mount 2 Pull the camera cables through the TVD SNB bracket tube and then attach the bracket to the pole mount with the expansion screws provided 3 Screw the cup base onto the swan neck bracket and fasten with the locking screw as shown A Then attach the mounting plate B to the cup base Note The mounting plate is shipped with the dome camera TruVision Dome Brackets Installation Manual 13 4 Loosen the screws on the dome enclosure using the supplied hex wrench and remove the dome enclosure and liner Connect the cables to the dome camera Using the enclosed screws attach the dome module of the camera to the bracket 7 Re attach the dome liner and enclosure to the camera To mount a bullet camera on a pole 1 Atthe desired mounting place securely fasten the TVD M PMA pole mount adaptor to the pole Pull the cables through the mount Connect the cables to the camera Use the enclosed screws to attach the c
6. interlogix des United Technologies TruVision Dome Brackets Installation Manual P N 1072649B EN REV 1 0 ISS 30SEP13 Copyright Trademarks and patents Certification Contact information 2013 UTC Fire amp Security Americas Corporation Inc Interlogix is part of UTC Climate Controls amp Security a unit of United Technologies Corporation All rights reserved The TruVision name and logo are trademarks of United Technologies Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products CE 2002 96 EC WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info For contact information see www utcfireandsecurity com or www utcfssecurityproducts eu Content Introduction 2 Bracket and cup base descriptions 2 Wall mount installation TVD SNB and TVD M2 WM 4 5 inch dome cameras A 3 inch dome cameras 6 2 inch dome wedge cameras 7 Flush mount installation TVD M2 FM 8 5 inch dome indoor cameras 8 Pendant mount installation TVD PPB 10 5 inch dome cameras 10 3 inch dome cameras 11 2 inch dome wedge cameras 12 Pole mount installation TVD M PM
7. ision Dome Brackets Installation Manual e TVD CB3 Converter pan TVD M2 WEBM Accessories Y Screw 4 mm 2 Expansion screw Screw 4 mm Locking screw 4 mm Black screw A mm pieces 10 mm 5 pieces 4 pieces 2 pieces 4 pieces Wall mount installation TVD SNB and TVD M2 WM Check the section Overview Fixed dome cameras by bracket on page 16 to confirm that the correct bracket is used with the camera 5 inch dome cameras Use the TVD SNB bracket and the TVD CB5 TVD CB5A cup base See Bracket and cup base description on page 2 for examples of the assembled brackets To mount a swan neck bracket on a wall 1 Pull the camera cables through the bracket tube Il and then attach the swan neck bracket to the d wall with the expansion screws A provided 4 TruVision Dome Brackets Installation Manual 2 Screw the cup base onto the swan neck bracket and fasten with the locking screw as shown 3 TVD CB5 only Using the enclosed screws attach the cup base to the camera housing 4 Loosen the screws on the dome enclosure 1 using the supplied hex wrench and remove the enclosure and dome liner 2 Connect the cables to the dome camera Insert the dome module into the cup base TVD CB5A shown and attach using the enclosed screws 7 Re attach the dome liner and enclosure to the camera TruVision Dome Brackets Installation Manual 3 inch dome cameras Use the
8. m O e Il E ee gt LL S ej SE GAL GAL GAL VSO say 299 maan WM zw VS sa9 299 Wi aen Joopul GAL OAL GAL ZN GAL GAL GAL ZIN GAL GAL GAL NMS esowey ssely VINd W GAL ddd dAL ONS OAL junoul 9 0d junou1 Bu 199 jUepuad JUNOW eM yunow ysn 4 sn 0 jayelg jyoyoriq Aq ses wes swop PdaXI 4 A IAIJ AO ZL 100p nO 100p nO Joopu pepnjoul junou ysn y Joopino Joopino Joopu Joopu Joopino Joopino Joopu Joopu Joopu Joopino Joopu pepnjoul junow ysn 4 Joopino JOopu Joopu Joopino vsdo Gi ego GAL GAL GAL vsdo Gi aen JOopul GAL dAL I 100p no 104 qe ins OSa O VINd W GAL yunouu lod x Id GAL yuUNow HuljiaojjUuepUuddg enue y UO e esu sjex9eJg auog UOISIANI L d N 6VA MNO dX dI GAN d N ZVA MNOtdX dI GAN d N Z ASPZN GAL d N WZ SSZZN GAL d N b MOLZN GAL d N Z AOLZN GAL d N F ASZZSIN GA 1 d N WE SSZZSW GAL d N WZ SSrZEW GAL d N 2 AGZZEW GAL d N Z AOLZEW GAL d N 2 AGZZZW GAL d N F AOLZZN GA L d N Z AOLZZW GAL d N WZ 3StZLIN GA L d N Z ASZZLIN GA 1 d N Z A0LZLIN GA1 d N Z AAOLZLN GAL ZN GAL GAL AAL GAL GAL NAS esoweg dl dl dl dl dl dl dl dl dl dl dl dl dl dl dl dl dl dl ssej9
9. ocking screw as shown 2 Pull the camera cables through the bracket tube and then attach the bracket to the ceiling with PH expansion screws 3 Screw the cup base onto the tube and fasten with the locking screw A T Using the enclosed screws attach the camera 0 mounting plate B to the cup base Note The camera mounting plate is shipped with j D the dome camera 4 Loosen the screws on the dome enclosure 1 using the supplied hex wrench and remove the dome enclosure and liner 2 TruVision Dome Brackets Installation Manual 11 Connect the cables to the dome camera Using screws attach the dome module to the mounting plate 7 Re attach the dome liner and enclosure to the camera 2 inch dome wedge cameras Use the TVD PPB bracket and the TVD CB2 cup base To mount a pendant mount bracket on a ceiling 1 Screw the mounting plate onto the tube and fasten with the locking screw as shown 2 Pull the camera cables through the bracket tube and then attach the bracket to the ceiling with expansion screws 3 Using four screws attach the converter pan TVD M2 WEBM to the cup base Then screw the cup base onto the pendant mount bracket and fasten with the locking screw 4 Loosen the screws on the dome enclosure using the supplied hex wrench and remove it SS AR Jee eck Y KC EG 12 TruVision Dome Brackets Installation Manual 5 Using 2 screws attach the camera
10. on page 2 for examples of the assembled brackets To mount a flush mount bracket on a ceiling 1 On the false ceiling mark the position and size of the housing pass through hole Cut a hole with a diameter of between 176 and 180 mm Make sure the cables for the camera are prepared Note The ceiling thickness must be less than 30 mm 8 TruVision Dome Brackets Installation Manual 2 Using screws provided fasten the mounting plate A to the in ceiling mounting base B 3 Push the dome camera into the in ceiling mounting base Caution For safety reasons use safety cables to securely attach the camera dome to the in ceiling mounting base and to attach the in ceiling mounting base to the building s infrastructure 4 Rotate the camera 10 degrees counterclockwise A and then securely fasten the camera to the in ceiling mounting base using the lock screws B 5 Push the camera with in ceiling mounting base into the ceiling hole 6 Using the lock screws A securely fasten the camera to the ceiling 7 To set up the camera image remove the camera enclosure and connect the RCA analog video output to a monitor D Loosen the lens set screw E and pan A tilt B or rotate C the lens to obtain the desired surveillance angle Adjust the lens focus When all adjustments have been done refasten the lens set screw 8 Using screws attach the trim ring to the in ceiling mounting base on the ceiling
11. osed screws attach the dome module of the camera to the bracket Re attach the dome liner and enclosure to the camera 2 inch dome wedge cameras Use the TVD SNB bracket and the TVD CB2 cup base See Bracket and cup base description on page 2 for examples of the assembled brackets To mount a swan neck bracket on a wall 1 TruVision Dome Brackets Installation Manual Pull the camera cables through the bracket tube and then attach the swan neck bracket to the wall with the expansion screws A provided ETa Q 0 Using four screws attach the converter pan TVD M2 WEBM to the cup base a 8 3 Then screw the cup base onto the swan neck bracket and fasten with the locking screw 4 Loosen the screws on the dome enclosure using the supplied hex wrench and remove it uw WN y SS 5 Connect the cables to the dome camera Using two screws attach the camera base plate to the converter pan on the cup base 6 Re attach the camera enclosure to the camera Flush mount installation TVD M2 FM Check the section Overview Fixed dome cameras by bracket on page on page 16 to confirm that the correct bracket is used with the camera Note For safety purposes the mounting surface must be able to support three times the combined weight of the bracket cup base and camera 5 inch dome indoor cameras Use the TVD M2 FM bracket See Bracket and cup base description
Download Pdf Manuals
Related Search