Elmes ST50H, ST100H, ST200H installation manual
Contents
1. RG switch for more than 3 and less than 8 seconds led lights Releasing the switch LED continues to light indicating entering this programming procedure b pressing any hand transmitter switch to set the receiver s relay c when required motor rotation time has lapsed max 60 minutes press the hand transmitter switch again The receiver s relay is reset and motor stops After 2 seconds the led starts blinking confirming end of the procedure Notice to obtain on off bi stable mode of operation of the receiver s relays the hand transmitter switch in point 2c above must be pressed twice in less than 2 second interval 3 Programming deleting all transmitters from the receiver s memory press receiver s PRG switch led lights for more than 8 seconds until the receiver LED starts blinking confirming end of the procedure Memory of the receiver is cleared Important Procedures 2 and 3 can be performed with valid transmitter s in the receiver s memory ST wiring diagram WOO dO ID SU NOILLdO LASTA WALL SWITCH LIVE NEUTRALZ 2 OVAC MOTOR GROUND Description of ST wiring connectors L mains supply connector LIVE wire mains supply 220 230VAC N mains supply connector NEUTRAL wire mains supply 220 230VAC a mains supply connector ground wire of mains supply cable za lie motor connector ground wire of roller motor cable OPEN motor connector LIVE wire of roller motor cable open2. and operates in changing rotation stop mode up stop down stop up etc Example one two channel hand transmitter controls two roller shades With the use of four channel hand transmitter Elmes CH4H up to four rollers can be controlled this way Important When mode 2 is selected it is necessary to perform point 1 of programming procedures see below and assign the transmitter buttons to controlled rollers The receiver may be also wire controlled by the use of pulse type two way wall switch Separate inputs are provided for up rotation and down rotation control and one common point Resetting the receiver s motor relays stopping the motor is done either by passing of programmed time lapse period or by shorting the reset input RS to ground COM IMPORTANT Connecting 220 230VAC mains supply to the ST receiver requires live line wire to be connected to point L of the receiver while neutral line wire to point N ST PROGRAMMING PROCEDURES 1 Programming learning transmitter s to receiver s memory max 12 a press receiver s PRG switch for less than 3 seconds led lights Releasing the switch LED continues to light red indicating entering the programming procedure b press any transmitter button twice and the receiver s LED switches off and starts blinking confirming end of the procedure The transmitter is in receiver s memory 2 Programming setting the motor rotation time receiver s relays reset a press receiver s P
3. elmes Elmes ST50H ST100H ST200H installation manual WINDOW ROLLER SHADES WIRELESS CONTROL SET WITH CODE HOPPING SECURITY ST50H roller shades control set with up to 50 meters range 12V bat 303 MHz ST100H roller shades control set with up to 100 meters range 12V bat 433 92MHz ST200H roller shades control set with up to 200 meters range 9V bat 433 92 MHz A set consists of 230VAC mains powered radio receiver and two 12V battery key fob hand transmitters STSOH ST100H or two 9V battery hand transmitters ST200H designed for wireless window roller shades control Both the transmitter encoder and the receiver decoder use the KEELOQ code hopping technology The receiver is fully programmable and has two power relay outputs for connecting roller shades 230VAC motor up and down rotation supply lines to the 230VAC mains The receiver features built in led that provides necessary programming status indication Transmitters are with two different colour switches corresponding to up or down roller shades rotation The receiver features two user selected modes of operation set by jumper 1K 2K Mode 1 jumper 1K 2K closed Each switch of the two channel hand transmitter is responsible for only one way start stop rotation of the roller s motor Example red switch for up rotation and grey switch for down rotation only Mode 2 jumper 1K 2K opened Each switch of the two channel hand transmitter is pre programmed to different receiver
4. rotation middle motor connector NEUTRAL wire of roller motor cable CLOSE motor connector LIVE wire of roller motor cable close rotation COM manual wall type pulse switch connector common ground point wire CL manual wall type pulse switch connector close rotation OP manual wall type pulse switch connector open rotation RS reset connector for optional photo or infrared cell NO type valid in CLOSE rotation only Closing the photo cell inputs RS and COM while CLOSE motor rotation will result in stopping the motor rotation jumper FOTO user set to close or stopping the motor rotation and switch to reverse rotation OPEN jumper FOTO user set to open WARNING Under no circumstances points COM CL OP RS may be connected to any voltage SPECIFICATIONS ASK radio high security code hopping receiver and two hand transmitter set EC standard 433 92 MHz frequency with 12V miniature battery ST100H or 9V battery ST200H up to 100 meters ST100H or 200 meters ST200H operation range in open field relays handling up to 16A 220 230V AC in built LED for programming indication power supply 220 230VAC controller and motor up to 12 transmitters in standard set KEELOQ is a registered trade mark of Microchip Technology Inc USA Copyright by Elmes Electronic 2002 All Rights Reserved
Download Pdf Manuals
Related Search