4-Port Dual View HDMI Switch User Manual
Contents
1. 29 General 29 Rack Mounting cr mx eer REDE EE 31 Technical 32 International iude e RR UIRerdueimie nk Dee Rte n 32 North 32 Specificatioris n ritis m E RATS 33 Limited 34 vi 1 5482 User Manual About this Manual This User Manual is provided to help you get the most from your VS482 system It covers all aspects of installation configuration and operation An overview of the information found in the manual is provided below Introduction introduces you to the VS482 system Its purpose features and benefits are presented and its front and back panel components are described Hardware Setup describes how to set up your VS482 installation The necessary steps are provided Operation explains the fundamental concepts involved in operating the VS482 via the front panel pushbuttons remote controlled On Screen Display OSD or through the RS 232 serial interface An Appendix provides specifications and other technical information regarding the 5482 vii VS482 User Manual Conventions This manual uses the following conventions Monospaced Indicates text that you should key in Indicates keys you should press For example Enter means2. 5 6 men 8 No Component Description 1 Up Down Left Press the Up Down Left Right button to cycle Right Buttons through the OSD menu selection 2 Setup Press this to confirm the selection on the OSD screen 3 On Press this to power on the display 4 Off Press this to power off the display 5 Port Selection Buttons Press a button to bring the focus directly to the source 1 4 device attached to its associated port 6 Menu Press this to enable disable the OSD menu Info button Press this button to display information about the source device on the upper left side of the screen The information can include Source port number Source port number Source Type or turned off 8 ARC Enable Disable ARC function See ARC Commands page 18 9 HDMI Mute Enable Disable audio for the output HDMI port See Mute Commands page 17 2 Hardware Setup device is provided on page 29 Please review it before 1 Important safety information regarding the placement of this proceeding 2 Make sure that the power to all devices connected to the installation are turned off 3 Make sure that all devices you will be installing are properly grounded Rack Mounting For convenience and flexibility the VS482 can be mounted on system racks To rack mount a unit do the following 1 Using the screws provided in the Rack Mount Kit screw the mounting bracket into the
3. R DAMA PHS SMa SJIT 11363 2006 RSE X TEC SUB ESL ID AMER DRAMAS tHsJ T 11363 2006 IRB Fe Eo 5482 User Manual User Information Online Registration Be sure to register your product at our online support center International http support aten com North America http www aten usa com product_registration Telephone Support For telephone support call this number International 886 2 8692 6959 China 86 10 5255 0110 Japan 81 3 5615 5811 Korea 82 2 467 6789 North America 1 888 999 ATEN ext 4988 United Kingdom 44 8 4481 58923 User Notice All information documentation and specifications contained in this manual are subject to change without prior notification by the manufacturer The manufacturer makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties as to merchantability or fitness for any particular purpose Any of the manufacturer s software described in this manual is sold or licensed as is Should the programs prove defective following their purchase the buyer and not the manufacturer its distributor or its dealer assumes the entire cost of all necessary servicing repair and any incidental or consequential damages resulting from any defect in the software The manufacturer of this system is not responsible for any radio and or TV interfere
4. Before working on the rack make sure that the stabilizers are secured to the rack extended to the floor and that the full weight of the rack rests on the floor Install front and side stabilizers on a single rack or front stabilizers for joined multiple racks before working on the rack Always load the rack from the bottom up and load the heaviest item in the rack first Make sure that the rack is level and stable before extending a device from the rack Use caution when pressing the device rail release latches and sliding a device into or out of a rack the slide rails can pinch your fingers After a device is inserted into the rack carefully extend the rail into a locking position and then slide the device into the rack Do not overload the AC supply branch circuit that provides power to the rack The total rack load should not exceed 80 percent of the branch circuit rating Make sure that all equipment used on the rack including power strips and other electrical connectors is properly grounded Ensure that proper airflow is provided to devices in the rack Ensure that the operating ambient temperature of the rack environment does not exceed the maximum ambient temperature specified for the equipment by the manufacturer Do not step on or stand on any device when servicing other devices in a rack 31 VS482 User Manual Technical Support International For online technical support including tr
5. To prevent damage to your installation it is important that all devices are properly grounded The device is equipped with a DC adapter This is a safety feature To help protect your system from sudden transient increases and decreases in electrical power use a surge suppressor line conditioner or un interruptible power supply UPS Position system cables and power cables carefully Be sure that nothing rests on any cables 29 6482 User Manual Never push objects of any kind into or through cabinet slots They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock Do not attempt to service the device yourself Refer all servicing to qualified service personnel If the following conditions occur unplug the device from the wall outlet and bring it to qualified service personnel for repair Liquid has been spilled into the device The device has been exposed to rain or water The device has been dropped or the cabinet has been damaged The device exhibits a distinct change in performance indicating a need for service The device does not operate normally when the operating instructions are followed Only adjust those controls that are covered in the operating instructions Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair 30 Appendix Rack Mounting
6. 4 This read only field shows the firmware version of the VS482 27 6482 User Manual This Page Intentionally Left Blank 28 Safety Instructions Read all of these instructions Save them for future reference Follow all warnings and instructions marked on the device Do not place the device on any unstable surface cart stand table etc If the device falls serious damage will result Do not use the device near water Do not place the device near or over radiators or heat registers The device cabinet is provided with slots and openings to allow for adequate ventilation To ensure reliable operation and to protect against overheating these openings must never be blocked or covered The device should never be placed on a soft surface bed sofa rug etc as this will block its ventilation openings Likewise the device should not be placed in a built in enclosure unless adequate ventilation has been provided Never spill liquid of any kind on the device Unplug the device from the wall outlet before cleaning Do not use liquid or aerosol cleaners Use a damp cloth for cleaning The device should be operated from the type of power source indicated on the marking label If you are not sure of the type of power available consult your dealer or local power company The device is designed for IT power distribution systems with 230V phase to phase voltage
7. Reset to Default On Version Version Number Note 1 The highlighted texts indicate the VS482 s default setting 2 The OSD function is disabled while 3D content is being displayed Switch to 2D content or a different input port to enable the OSD 23 VS482 User Manual Input Setting Menu Use this screen to select the video source device s for the HDMI input port s ATEN VS482 HDMI Device HDMI Device HDMI Device HDMI Device 1 Use the drop down menu to select a video source device for HDMI 1 input port Options are as follows HDMI Device Blu ray Player DVD Player Game Console Set Top Box Portable Device PC Note The default value HDMI Device does not point to any device It means there is no video source selected for that HDMI input port 2 Do the same for HDMI 2 to HDMI 4 input ports 24 3 Operation Audio Setting Use this screen to configure the VS482 audio settings ATEN VS482 HDMI Audio Output 1 Use the drop down menu to Enable or Disable ARC on the VS482 See Audio Return Channel ARC page 13 for more details on this feature Disable Enable 2 Use the drop down menu to select which audio channel receiver the VS482 uses The default value is Auto Auto Stereo 5 1 Channel 7 1 Channel 3 Use the drop down menu to turn on off the audio coming from the HDMI output port s Select On to enable audio from the active HDMI ou
8. AVR or speakers connected to the HDMI output ports of the 5482 Note The HDMI output port 1 is also ARC input port depending on whether the ARC feature is enabled or disabled See ARC Commands page 18 for more information In the following diagram audio from the TV goes to the VS482 through the ARC Input port and is then passed on to the AVR via the HDMI cable or the audio devices connected to the HDMI output ports A user can also connect to an audio device receiver using an optical or coaxial audio connector gt m m ARC input port Satellite STB etc EN x M SEL No need for another cable for audio Note 1 The scenario above works only if the TV supports HDMI and have ARC enabled 2 The ARC LED blue lights up to indicate that the ARC function is enabled There is no audio output if your HDTV does not support ARC function or if the ARC function is not enabled 3 Operation RS 232 Serial Interface The VS482 s built in bi directional RS 232 serial interface allows system control through a high end controller PC and or home automation home theater software package Configuring the Serial Port The controller s serial port should be configured as follows Baud Rate 19200 Data Bits 8 Parity None Stop Bits 1 Flow Control None Switch Port Commands The fo
9. Apply the video source s CEC to all display output port1 Apply the video source s CEC only to port 1 default The following table shows the available command list Command Control Enter Description cec off Enter CEC off cec auto Enter Connect the video source s CEC with all display output cec port1 Enter Apply the video source s CEC only to port 1 default 20 3 Operation Power On Detection POD The Power On Detection feature is turned on by default The formula for Power On Detection commands is as follows Power On Detection Control command Enter For example to turn off the Power On Detection feature input the following pod off Enter The following tables show the possible values and formats for the Control command Command Description pod Power On Detection command Control Description on Turn on default off Turn off Note Each command can be separated with a space The following table shows the available command list Command Control Enter Description pod on Enter POD enabled default pod off Enter POD disabled 21 VS482 User Manual Verification After entering a command a verification message appears at the end of the command line as follows Command OK indicates that the command is correct and successfully performed by the switch Command incorrect indic
10. SJ T 11964 2006 5 rers EDO eee eee ond cee ii User iii Online Registration iii Telephone iii User hi Sere onc etuer contis dr ae eig a di iii Package iv Gontents oot Wate Cere duce ei pr Id e Ee V About this vii GOnVentlolis viii Product viii 1 Introduction Ver VIO Wace 12 ct te ae Cd ois et Un el re Erit obe phon or ok aan rat 1 ie oet eluted 2 ca cm make eR RE e ER ERE EE 3 Source 3 Display Device RR ERE EROR 3 Gables petes ii eet E 3 c dee pure a Ge ee rea gee ad DR n RUE RUE ecd 4 x cese vocac OC RD Rua E dC Cosa Roc GE car roe 4 Rear VIEW ocio soar OR ER EGER LY n 5 IR Remote Control tes ee pede dw ete AE end 6 2 Hardware Setup Rack Mounting 7 Grounding ss e aou A Seb A PRU Rod teh I decas 8 IistallatiODi ame
11. input sources via front panel pushbuttons or through the RS 232 serial control port Features EDID Expert technology to set up different configurations via different EDID modes Allows users to view the HDMI input source port device for easy selection On Screen Display OSD for system configuration settings and information display Built in bi directional RS 232 serial control port for high end system control control signal extension extend the reach of the IR controller by adding an IR receiver unit IR receiver can be purchased separately Consumer Electronics Control CEC allows interconnected HDMI devices to communicate and respond to one remote control Superior video quality HDTV resolutions of 480p 720p 10801 1080p 1920x1080 VGA SVGA SXGA UXGA and WUXGA 1920 x 1200 Support multi channel audio 2 5 1 7 1 Power On Detection if the active HDMI video input source device is powered off LED is off the VS482 automatically switches to the next powered on video input source device Extract audio from HDMI input signal that supports both optical and coaxial digital audio and one stereo audio output Rack mountable all metal casing Plug and play no software installation required DDC compatible LED indication of A V source devices 1 Introduction Requirements The following equipment is required for a complete VS482 installation Source Device HDMI Typ
12. to communitcate with the video source system You can set up which EDID mode the VS482 uses with the following command EDID Command Control Enter The following tables show the possible values and formats for the Control command Command Description edid Enable EDID selection Control Description port1 Implement the EDID of the connected display to Port 1 and pass it to the video source auto Implement the EDID of all connected displays The VS482 uses the best resolution for all displays default default Implements ATEN s default EDID The following table shows the available command list Command Control Enter Description edid port1 Enter The EDID from Port 1 is passed to the video source edid auto Enter The VS482 implements the EDID of all connected displays and uses the best resolution for all displays default edid default Enter ATEN s default EDID is passed to the video source 19 6482 User Manual CEC Commands Consumer Electronics Control CEC allows interconnected HDMI devices to communicate and respond to one remote control The formula for CEC mode selection commands is as follows CEC Command Control Enter The following tables show the possible values and formats for the Control command Command Description cec Enable CEC selection Control Description off Disable CEC auto
13. 4 Port Dual View HDMI Switch VS482 User Manual Qm www aten com 5482 User Manual FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that which the receiver is connected Consult the dealer an experienced radio television technician for help RoHS This product is RoHS compliant SJ T 11364 2006 The following contains information that relates to China Sese V SCUER A BR USE RRASA ES EVA E YES UIT 11363 20061 SK ZI s
14. Tod n ee ert avd oan 9 Installing the RS 232 Controller 10 3 Operation S ert d aL LES ost ue Cels 11 Manual 11 Remote Control 11 Power On Detection o isl eem Werne dus 12 Audio Return Channel ARC 13 Initial 13 Enabling ARG eue a Sada eee YE 14 RS 232 Serial Interface musei Rb rbi n er 15 Configuring the Serial Port 15 Switch Port 15 Mute 2 e us 17 ARGC Commands e uA bep eater ee 18 EDID Commands 19 CEC 20 6482 User Manual Power On Detection 21 Verification PCR 22 Powering and 0 22 OSD Menu vated weed RM Bib Es 23 Input Setting 24 Audio Settings iiie eae Ad e XS 25 OSD Setting teat a See Ae ek DASS 26 System Setting gest aa ee ER RR ene 27 Appendix Safety Instructions
15. XGA 1920 x 1200 Power Consumption DC 5 3V 6 95W Environment Operating Temp 0 50 C Storage Temp 20 60 C Humidity 0 80 RH Non condensing Physical Housing Metal Weight 2 16 Kg Dimensions 43 72 x 15 86 x 5 54 cm LxWxH 33 VS482 User Manual Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT DISK OR ITS DOCUMENTATION The direct vendor makes no warranty or representation expressed implied or statutory with respect to the contents or use of this documentation and especially disclaims its quality performance merchantability or fitness for any particular purpose The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions or update For further inquiries please contact your direct vendor 34
16. ates that the command has the wrong format and or values Powering Off and Restarting If you power off the VS482 follows these steps before powering it on again 1 Power off the attached devices 2 Unplug the power adapter cable from the VS482 3 Wait 10 seconds and then plug the power adapter cable back in 4 After the VS482 is powered on power on the attached devices 22 3 Operation OSD Menu Use the MENU pushbutton on the remote control to view the OSD menu and cycle through the options in the order shown in the table below See IR Remote Control page 6 for details on how to use the remote control Menu Page Sub Menu Page s Input Setting HDMI 1 HDMI device Blu ray player DVD player Game Console Set Top Box Portable Device PC HDMI 2 HDMI device Blu ray player DVD player Game Console Set Top Box Portable Device IP HDMI 3 HDMI device Blu ray player DVD player name Console Set Top Box Portable Device HDMI 4 HDMI device Blu ray player DVD player man Console Set Top Box Portable Device Audio Setting ARC Disable Enable Audio Channel AUTO Stereo 5 1 Channel 7 1 Channel HDMI Audio Output On OSD Setting Message Display ode Channel Full Off Transparency 0 100 default is 75 System Setting EDID Auto Port 1 Default CEC Port 1 Auto Off
17. e A output connector s Note A DVI HDMI adapter is required when connecting a DVI source device Display Device Upto 2 display devices or receivers with an HDMI Type A input connector Cables 4HDMI cables Note 1 No cables are included in this package We strongly recommend that you purchase high quality cables of appropriate length since this will affect the quality of the audio and video display Contact your dealer to purchase the correct cable sets 2 If you wish to utilize the VS482 s high end serial controller function you will also need to purchase an appropriate RS 232 cable See Installing the RS 232 Controller page 10 VS482 User Manual Components Front View AUTEN HDMI switch No Component Description 1 Port LEDs The SELECTED port s LED bottom green lights up to indicate that the port is selected 2 ARCLED The LED blue lights up when the ARC function is enabled Power Pushbutton Press this button to turn on off the switch 4 Power LED The LED green lights up when the switch is powered on The LED orange lights up to indicate that the switch is in standby mode 5 IR Receiver This receives signals from the IR remote control 6 Port Selection Pressing a port selection pushbutton routes the A V Pushbuttons source from the corresponding input port to the output port for display 7 ARC button Pre
18. nce caused by unauthorized modifications to this device It is the responsibility of the user to correct such interference The manufacturer is not responsible for any damage incurred in the operation of this system if the correct operational voltage setting was not selected prior to operation PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE USE 6482 User Manual Package Contents The VS482 4 Port Dual View HDMI Switch package consists of 1 5482 4 Port Dual View HDMI Switch 1 IR Remote Control Unit 1 Power Adapter 1 User Instructions 1 Rack mount kit Check to make sure that all the components are present and that nothing got damaged in shipping If you encounter a problem contact your dealer Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit and or any of the devices connected to it Features may have been added to the VS482 since this manual was printed Please visit our website to download the most up to date version Copyright 2011 ATEN International Co Ltd Manual Part No PAPE 0347 AT1G Manual Date 2011 10 19 ATEN and the ATEN logo are registered trademarks of ATEN International Co Ltd All rights reserved All other brand names and trademarks are the registered property of their respective owners 5482 User Manual Contents FCG Inforfnatiom teed ob ii
19. nnect the hardware software controller here Hardware Software lt Controller 8 ym HDMI A V Source Devices This completes the basic installation of the 4 Port Dual View HDMI Switch You may now power on the display and source devices 6482 User Manual Installing the RS 232 Controller In order to use the 5 232 serial interface to attach a high end controller such as a PC to the VS482 use serial cable such as a modem cable The end connecting to the VS482 should have a 9 pin male connector Connect this to the serial interface on the rear of the VS482 Refer to number 5 on the previous diagram Note To configure the controller serial port see page 15 Chapter 3 Operation Overview The 4 Port Dual View HDMI Switch offers easy and flexible source device selection with either the front panel pushbuttons with the remote control or through the 5 232 serial interface Note 1 Whenever the VS482 is powered on and there is no video input source connected it automatically selects Port as the active port i e the Port 1 LED lights up You may choose one of the methods outlined below to select a different port as your active port 2 The VS482 takes about 10 20 seconds to boot up the system and apply the system configuration when first powered on Manual Selection To select a source device press the pushbutton that cor
20. oubleshooting documentation and software updates http support aten com For telephone support see Telephone Support page iii North America Email Support support aten usa com Online Technical Support Troubleshooting Documentation Software Updates http www aten usa com support Telephone Support 1 888 999 ATEN ext 4988 When you contact us please have the following information ready beforehand Product model number serial number and date of purchase Your computer configuration including operating system revision level expansion cards and software Anyerror messages displayed at the time the error occurred The sequence of operations that led up to the error Any other information you feel may be of help 32 Appendix Specifications Function VS482 Display Connections 2 Connectors Device HDMI In 4 x HDMI Type A Female Black Display HDMI Out 2 x HDMI Type A Female Black Optical Audio 1 x Toslink Black Coaxial Audio 1 x RCA Orange Stereo Audio 2 x RCA Red White RS 232 Port 1 x DB 9 Female Black Power 1 x DC Jack IR Extension Port 1 x 3 5mm phone jack Switches Port Switch 4 ARC Selection 1 Power Button 1 LEDs Selected 4 Green ARC Selected 1 Blue Power 1 Green Orange IR Control 1 Video HDTV resolutions of 480p 720p 1080i 1080p 1920x1080 WU
21. r On Detection feature from working properly 3 Operation Audio Return Channel ARC Audio Return Channel ARC allows an HDMI source device that receives content via air waves such as a TV or STB connected to a satellite antenna to send audio upstream to your HDMI display devices using only one HDMI cable Initial Setup The VS482 supports dual HDMI output for dual view such as two HDTV or audio video receiver AVR applications as shown in the following diagram HDMI Sources Audio Output ed or HDMI Displays The audio video coming from the HDMI sources Blu ray DVD etc are received by the VS482 and then passed on to the HDMI displays TV projector or AVR However if the HDMI audio or video is coming from the TV through a satellite antenna or STB you can enable ARC so that audio is sent to the AVR HDMI receiver through the HDMI cable or the device s connected to the audio output port s See p 14 for the diagram Note 1 Without ARC you must connect another cable specifically for passing audio from the TV to the AVR or the device s connected to the audio output port s 2 The ARC function requires HDTV built in ARC function and connect to the correct HDMI output port Check your HDTV s user manual for this information VS482 User Manual Enabling ARC With ARC enabled the TV can act as the HDMI source and send audio upstream to the
22. responds to the port to which it is connected Note The Port LED green light indicates which port is currently selected Remote Control Selection To select a source device with the remote control press the number button that corresponds to the port to which it is connected See IR Remote Control page 6 for more details Note Aim the remote control unit at the IR receiver located on the front panel ofthe VS482 For optimum performance make sure there is a clear line of sight between the remote control unit and the IR receiver 6482 User Manual Power On Detection The Power On Detection feature enables the VS482 to do the following It automatically switches to the next port with a powered on source device connected when the current active port is powered off When the 5482 is turned on the least numbered port with a video input source connected acts as the active port To select another port see Manual Selection page 11 If you have manually selected an active port and the video input source device is disconnected but not powered off the VS482 does not use any other powered on video input source device Note 1 Whenever the VS482 is powered on and there is no video input source connected it automatically selects Port as the active port i e the Port 1 LED lights up 2 Some video sources devices may use a different Hot Plug Detect HDP implementation that prevents the Powe
23. rmulas for Switch Port commands are as follows 1 Switch Command Input Command Port number Enter For example to switch input port to port 02 type the following sw i02 Enter 2 Switch Command Control Enter For example to switch to the next port input the following sw Enter 6482 User Manual The following tables show the possible values and formats for the Input command Port Number and Control Command Description Sw Switch command Input Command Description Input command Port number Description 01 04 port default is 01 Control Description on Turn on the display off Turn off the display Next Port Previous Port Note 1 Each command string can be separated with a space 2 The Port Number command string can be skipped and the default value will be used The following table shows the available command list Command Input Port Control Enter Description Sw i Xx Enter Switch Input Port Sw on Enter Turn on Display out off Enter Turn off No output Sw Enter Switch to the next input 5 Enter Switch to the previous input 16 3 Operation Mute Commands Enable or disable audio coming from the output HDMI port using the following command Mute Command Control Enter The following tables sho
24. side of the unit as show in the diagram below hillips hex head M3x8 VS482 User Manual 2 Screw the bracket into any convenient location on the rack Note These screws are not provided We recommend that you use 5 x 12 Phillips Type I cross recessed type screws Grounding To prevent damage to your installation it is important that all devices are properly grounded 1 Use a grounding wire to ground the VS482 by connecting one end of the wire to the grounding terminal and the other end of the wire to a suitable grounded object 2 Make sure that the computer s device s that the VS482 connects to are properly grounded 2 Hardware Setup Installation Installation of the VS482 is simply a matter of plugging in the appropriate cables To install the switch refer to the installation diagram below as you perform the following steps 1 Use an HDMI cable to connect the HDMI input port on the video display device to the HDMI output port on the rear of the VS482 Use HDMI cables to connect the HDMI output ports on the source device s to the HDMI input ports on the VS482 Plug the provided power adapter into an appropriate AC power source plug the power adapter cable into the Power Jack on the VS482 Connect your audio devices such as speakers or AVRs to the Stereo Audio Ports or Digital Audio Ports Optional To edit the VS482 system settings through the RS 232 port co
25. ss this button to enable disable the ARC function 1 Introduction Rear View 1 23 4 Spit if 0 m m cm Description 1 Grounding Terminal The grounding wire used to ground the unit attaches here Note The grounding wire is not included in this package Contact your dealer for more information 2 Power Jack The power adapter cable plugs in here 3 IR Extender Port Connect the IR Extender to this port Note The additional IR receiver can be purchased separately 4 RS 232 Serial Port This is the serial remote port for input source selection and high end system control including firmware upgrade 5 Stereo Audio Ports The red port is for the right audio channel and the white port is for the left audio channel 6 Digital Audio Ports Connect the optical and coaxial audio cables to these ports 7 HDMI Out port 2 The cable from the HDMI display or receiver device plugs in here 8 HDMI Out port 1 The cable from the HDMI display device or receiver ARC In plugs in here Connect the ARC audio input connector or receiver to this port The ARC audio can be transmitted back to audio receivers through this connectivity 9 HDMI In The cables from the HDMI source devices can plug into any of four available ports 5482 User Manual IR Remote Control
26. to press the Enter key If keys need to be chorded they appear together in the same bracket with a plus sign between them Ctrl Alt 1 Numbered lists represent procedures with sequential steps Bullet lists provide information but do not involve sequential steps gt Indicates selecting the option on a menu or dialog box for example that comes next For example Start Run means to open the Start menu and then select Run Indicates critical information Product Information For information about all ATEN products and how they can help you connect without limits visit ATEN on the Web or contact an ATEN Authorized Reseller Visit ATEN on the Web for a list of locations and telephone numbers International http www aten com North America http www aten usa com viii Chapter 1 Introduction Overview With more and more HDMI devices entering the Home Theater market the need for simultaneous access to different HDMI A V sources is becoming increasingly important Now the VS482 4 Port Dual View HDMI Switch offers an easy and affordable way to add HDMI capabilities to your home theater system by allowing you to switch easily between up to four HDMI Audio Video sources that are connected to up to two HDMI displays The VS482 supports four HDMI video input sources and two HDMI output displays It is designed for two HDTV audio video receiver AVR or HD projectior display applications The VS482 complies
27. tput port and select Off to disable it On Off 25 VS482 User Manual OSD Setting Use this screen to configure the VS482 OSD settings ATEN VS482 Use the drop down menu to select which display mode the VS482 uses to display information in the upper left corner of the screen Options are as follows Channel Full Off Channel This shows the source port number Full This shows the source port number and source type See Input Setting Menu page 24 for the list of source types Off There is no information shown Select the visibility of the OSD menu when it is invoked Press the menu button to enter the adjustment menu Press the up down button to select increase decrease the value then press the setup button to adjust The value 100 shows a fully visible and opaque OSD menu The default value is 75 Note The Transparency value must be divisible by 5 1 5 10 15 20 and so on 26 3 Operation System Setting Use this screen to configure the VS482 system settings ATEN VS482 1 Use the drop down menu to set up which EDID mode the VS482 uses See EDID Commands page 19 for more details Auto Port 1 Default 2 Use the drop down menu to select how the video source s CEC is applied See CEC Commands page 20 for more details Off Auto Port 1 3 Set this to On to have the VS482 return to default settings when it is reset Otherwise select Off On Off
28. w the possible values and formats for the Control command Command Description mute Enable Disable audio of HDMI output port Control Description on Mute on audio from HDMI output port is disabled off Mute off audio output enabled default Note Each command string can be separated with a space The following table shows the available command list Command Control Enter Description mute on Enter Mute on no audio mute off Enter Mute off audio out 17 6482 User Manual ARC Commands Audio Return Channel ARC allows a source device TV STB etc to send audio upstream to an audio video receiver using only one HDMI cable The formula for enabling disabling ARC is as follows ARC Command Control Enter The following tables show the possible values and formats for the Control command Command Description arc Enable Disable ARC Control Description on ARC on output audio passes from HDMI output port 1 to HDMI output port off ARC is disabled default The following table shows the available command list Command Control Enter Description arc on Enter ARC on arc off Enter ARC off 18 3 Operation EDID Commands Extended Display Identification Information EDID is a data format that contains a display s basic information and is used
29. with HDMI standards and is designed to support 3D content as well as featuring Audio Return Channel ARC functionality The VS482 also offers fast switching and has OSD display controls for video audio system configuration and information With four HDMI A V input ports the VS482 allows you to connect four HDMI devices such as an HD camcorder satellite box HD DVD player hi def Blu ray player home theater PC stand alone streaming media player or gaming console to two HDMI monitors displays projectors or TVs at the same time The remote control and convenient front panel pushbuttons allow you to quickly and easily toggle between A V sources while the front panel LEDs indicate the source device at a glance Furthermore for complete system and install integration RS 232 control is standard through the VS482 s built in bi directional RS 232 serial remote port that allows the switch to be controlled through a Control Unit PC and or home automation home theater software package VS482 User Manual Features Allows up to four HDMI A V sources to be connected to two HDMI displays Easy and affordable way to add four HDMI inputs to your home theater system HDCP 1 2 compatible Supports HDMI 3D Audio Return Channel and deep color Audio Return Channel ARC function connect an HDMI cable to the ARC port to send audio from your source device to your audio video receiver Instant switching between HDMI
Download Pdf Manuals
Related Search