USER'S GUIDE - E&P Hydraulics
Contents
1. 1 2 Specific features of the remote control Top view remote control mobile home E amp P HYDRAULICS 1 12 15 14 m 13 VON a 2 LBS c 1 LED Slope to strong 2 LED Battery Low voltage 5 M 9 11 4 6 8 3 LED Engage the handbrake 10 Button Left side 4 LED Jacks not fully retracted 11 Button Rear side 5 Button ON OFF 12 Button Front side 6 Button Manual mode 13 Button Right side 7 Button Automatic mode on 14 8 Button Retract all Jacks 15 9 LED Manual mode 16 LED Level indicator Button Inclination function LED Remote control Battery Low User manual E amp P HYDRAULICS 1 3 Product labelling The product CE label is present on the back side of the product as indicated in the illustration below Another registration label is not directly visible but is located inside the product behind the battery cover All labels are attached by the manufacturer and should not be removed Battery 9V C Ep HYDRAULICS LEVELSYSTEM Remote control Artnr JSM RC EP Serienr RC1000 Battery 9 volt PP3 Product CE label Battery cover 868 MHZ conforms EN300220 EN301489 EN60950 Registration label m bei w VI S For traceability and warranty administration the registration number label is placed inside the product to be sure it remains undama2. injury Therefore this system may only be installed by professional technicians with sufficient practical experience and a thorough relevant technical training At all times the installer will bear sole responsibility for the assembly of the system This document is based on hundreds of test hours as well as many successful installations If you follow this manual step by step you will see what a wonderful user friendly quality product this is However there will always be aspects that can be improved If you have any suggestions remarks or questions concerning this product or manual please do not hesitate to contact us On behalf of E amp P Hydraulics User manual E amp P HYDRAULICS 1 1 Unpacking the remote control Remove the remote control and it s accessories from the box and packing material Refer to the packing list to make sure you have received all the items ordered Visually inspect the remote control and accessories for any evidence of physical damage Immediately contact E amp P Hydraulics if anything appears to be damaged DURACELL Contents ucl Remote control Holder Battery 9V Antenna premounted a C N Manual Attention e Details may differ from the illustration above but functionality should be identical e f the Remote control is delivered as a part of the complete system this manual can be replaced by the manual belonging to the complete levelling set User manual
3. DRAULICS LEVELSYSTEM www ep hydraulics co uk Made in Holland
4. User manual E amp P HYDRAULICS Ep HYDRAULICS LEVELS YS TEM DCAM PER CAM FP ER Remote control Mobile home User manual E amp P HYDRAULICS Copyright 2013 E amp P Hydraulics This manual is copyrighted with all rights reserved Under the copyright laws this may not in whole or in part be copied photocopied reproduced translated or converted to any electronic medium or machine readable from without prior written consent of E amp P Hydraulics Limited Warranty Under all circumstances this manual should be read thoroughly before installing and or using the product In no event shall E amp P Hydraulics be liable for any direct indirect special consequential or incidental damages arising out of the use or inability to use this documentation or product even if advised of the possibility of such damages In particular E amp P Hydraulics shall not be liable for any hardware software or data that is stored or used with this product including the cost of repairing replacing or recovering the above E amp P Hydraulics reserves the right to change parts of the device at any time without preceding or direct announcement to the client E amp P Hydraulics reserves the right to revise the manual s and to make changes in the contents without obligation to notify any person or entity of the revision or change A registration number appears on the product Make sure that this official registration number has not been remov
5. ed It should be used whenever servicing by E amp P Hydraulics or an authorized E amp P Hydraulics dealer is necessary Important This equipment has been tested and found to comply with the limits valid for this device pursuant to EN300220 EN301489 EN60950 rules conform 868MHZ These limits are designed to provide reasonable protection against harmful interference when this product is operated in a commercial environment Any unauthorized changes or modifications to this device could void the user s authority to operate this equipment For CE countries This device is in conformity with the CE standards Please note that this device can ONLY be used with the official E amp P Hydraulics level system parts to conform to these standards EPRC 01 vers ams sept 2013 User manual E amp P HYDRAULICS Index dile 1 Chapter 1 Remote Control Mobile home EPRC 01 1 1 Unpacking the remote control 2 1 2 Specific features of the remote control 3 1 3 Product labelling 4 Chapter 2 Installation Programming essere 5 Chapter 3 Technical specifications sees 6 Chapter 4 Users advices tips 7 User manual E amp P HYDRAULICS Preface The E amp P Hydraulics Remote control combines the demand for fixed built in operating unit and remote controlled operation of the Mobile h
6. ged This official registration number is directly related to the device E amp P Hydraulics or the dealer may ask for this number e g when the product needs to be serviced so please familiarise yourself with it Changing battery Remove the battery cover by firmly pressing then sliding out and lifting the cover from the casing Insert the battery and carefully mount the battery cover User manual E amp P HYDRAULICS 2 Installation Programming e Step 1 In order to pair the remote control to the system remove the fuse 15Amp out of the cable assembly from the hydraulic levelsystem or disconnect the de 9 pins cable connector from the main unit do this by gently pressing the two hooks on the side of the connector Extra note When using a 24V system remove the 6p cable connector from the main unit si Step 2 Press the Buttons deploy jacks automatically no 7 and retract all jacks no 8 simultaneously for at least 1 second When done the Indicator LED no 14 with the surrounding I Hm 4 arrows starts blinking GREEN ORANGE nervously This means the remote control is looking for its receiver mounted within the main unit Step 3 Depending on what action you performed under step1 reconnect the 9 pin connector the 6 pin connector or the fuse to the system Y Extra Note The pairing process should be made within a certain time apr 20 sec The remote control turns off automatically When the Ind
7. icator LED goes off the pairing process is guaranteed ch Step 4 Turn the remote control ON by pressing button on off no 5 for at least 1 second Now the GREEN LED between the four arrows in the middle will light up by wma flashing As long as you see this LED flashing the remote control is searching for contact with the main unit When contact is made the flashing stops By means of illumination of one or two ORANGE arrows the remote control shows in which way your vehicle is leaning Or the GREEN LED There could be 8 1 9 possibilities ENSBEBEEENHSH Using the Remote control After programming your remote control you now have two options to level your Mobile home Operating your system by the remote control or the built in control panel The operation is described in the E amp P Hydraulics User s Guide of the Mobile home User manual E amp P HYDRAULICS 3 Specifications Electrical Power 9V PP3 battery Compatibility 868MHz EN300220 EN301489 EN60950 Physical Weight remote control 145 Gr Weight holder 10 Gr Dimensions Length x Width x Height 140 x 83 x 24 mm Environmental Operating temperature 20 C 40 C Humidity 20 95 RH non condensing User manual E amp P HYDRAULICS 4 Users advices tips 4 1 Antenna receiving range It may be that the main unit is built in such a way that receiving a signal between the remote control and the main unit works poorly or e
8. ome level system The ergonomic design ensures effortless handling and the sympathetic good looks will automatically enhance your working environment It is based on proven E amp P Hydraulics technology which forms the basis of all our E amp P Hydraulics products After installation one button operates the entire system Within the E amp P Hydraulics strategic vision this products is 10096 user friendly and reliable This philosophy does not only apply to our customers end users The technicians installing this device system at the dealers are also very important to us This product greatly depends on a proper professional installation That s the reason why E amp P Hydraulics do all they can do to support the people who are responsible for installing our products for you This manual is part of our policy In this manual we explain the general features and how to install this product as simply as possible to the E amp P Hydraulics level system as properly and efficiently as possible Precisely follow these instructions for the installation because installing the E amp P Hydraulics system is a precise job Fully installing the system requires a high level of skill After all we are dealing with equipment that must be able to withstand huge forces something that is often underrated by people with insufficient technical training If the installation is not performed correctly serious damages could result in a short time and even personal
9. ven not at all caused by vehicle construction materials e g steel wood plastics etc In this case there is a possibility to move the antenna away from the main unit by means of an optional extension cable length max 2 metre available from E amp P Hydraulics 4 2 Upgrading your existing system An upgrade of the system must be made if the system was installed or purchased before 2013 When using a remote control with a system installed or purchased before this date you need to replace the main unit with an updated version of the main unit incl antenna socket main unit 6 p connect 9 p connect Antenna connection Antenna 4 3 Which device takes command The device which is operated first remote control or control panel takes the command to control the system until that device is switched off If you would like to switch from one control device to another you need to switch off the power from the device that was in operation first In the event of switching off the remote control you have to wait a little time to give the system enough time to switch off contact between the remote control and the main unit 4 4 Low Battery level indicator When the battery level indicator LED no 16 lights RED the device does not stop working immediately After this signal it is possible to use the remote control another 4 times Make sure there is a spare battery in the vehicle E amp P HYDRAULICS Ep HY
Download Pdf Manuals
Related Search