SLO Insulated Wrench Operating Instructions.qxp
Contents
1. SLO Insulated Wrench Operating Instructions Rev 1 0 Ref Item 500204 SLO Insulated Wrenches Insulated Boot For use on electrical systems up to 50 volts NX Reduces possibility of shorting or shock a PVC heat shrink insulation Torque Seale May be used for torque on battery terminals wee Sige 525 oe Double insulation N Calibrating Torque Wrenches Red inside amp Yellow outside l D N To calibrate torque wrenches either use a torque analyzer or torque transducer within the range of the torque wrench For click wrenches calibrate torque in First Peak mode with a digital analyzer or transducer Make sure to apply the torque slowly and smoothly at the Load Point Line near end of the handle 1 Select a torque analyzer or transducer that covers the torque range of the wrench Connect wrench to the torque analyzer or transducer using the appropriate adapters as needed not supplied 2 Apply torque clockwise slowly until wrench clicks and note reading 3 Adjust wrench to required torque setting as described below 4 Test and repeat adjustment as necessary to obtain desired value 5 Recalibrate torque wrench at prescribed intervals Adjustement Adjusting T Setti z T justing Torque Setting eB z 1 Use the adjustment knob to change torque setting 140 2 Swing lever clockwise to increase torque or counterclockwise to Torque Scale decrease torque Applying Torque 1 Toward the end of t2. dhered to the handle tube Then assemble rubber hand grip over the heat shrink end cap Applying Torque 1 Tighten nut or bolt by applying a steady even pull using built in ratchet as necessary Wrench should be kept at 90 degrees to axis of bolt during tightening When pre set torque is reached the wrench will slip 2 The wrench will automatically reset itself for the next application 3 With its unique design it s impossible to over tighten beyond the preset load mountz the torque tool specialists 800 456 1828 Fax 408 292 2214 sales etorque com www etorque com Corporate Headquarters 1080 North 11th Street San Jose CA 95112 Phone 408 292 2214 Fax 408 292 2733 www etorque com
3. elt adhered to etd GS IEC 900 ESI 26 3 the handle tube The normal hand grip is then assembled over the Ss NG heat shrink end cap providing additional protection Calibrating Torque Wrenches Adjusting To calibrate torque wrenches either use a torque analyzer or torque transducer within the range of the torque Key wrench For cam over torque wrenches calibrate torque in Peak mode with an analyzer or transducer Make sure you apply the torque slowly and smoothly 1 Select a torque analyzer or transducer that covers the torque range of the TSN wrench Connect wrench to the torque analyzer or transducer Apply torque clockwise slowly until wrench slips and note reading Adjust wrench to required torque setting Test and repeat adjustment as necessary to obtain desired value Recalibrate torque wrench at prescribed intervals oR WP Adjusting Torque Setting 1 Remove rubber handle grip Then remove the sealed heat shrink cap 2 Remove end cap from wrench and insert special adjusting key 3 The special Adjusting Key is an articulated design When in use the two halves are set at 90 this allows downward force to be exerted on the Sliding Lock while rotating the Adjusting Screw 4 Turn clockwise to increase torque and counter clockwise to decrease torque Do not adjust torque above or below the recommended torque ranges Tighten end cap back on qq Key 5 Then seal the end cap with heat shrink end cap hot melt a
4. he wrench is the Load Point Line Grab handle at that Load Point end to apply torque If you the grab handle closer toward head then you will apply more torque than what the wrench is set for The wrench is a length dependent tool 2 Tighten nut or bolt by applying a steady even pull using built in ratchet as necessary Wrench should be kept at 90 degrees to axis of bolt during tightening When pre set torque is reached the wrench will click 3 After the click do not apply any more torque or you will over tighten it Note Best protection for the operator is using an insulated socket with the wrench For operator protection red insulation is underneath the yellow insulation Once the red is visible remove for service mountz the torque tool specialists 800 456 1828 Fax 408 292 2214 sales etorque com www etorque com Corporate Headquarters 1080 North 11th Street San Jose CA 95112 Phone 408 292 2214 Fax 408 292 2733 www etorque com TSN Insulated Wrench Operating Instructions Rev 1 0 TSN Insulated Wrenches For any application which requires the tightening of fasteners under a electrically live situations The TSN wrench head and handle are Insulated Boot ey securely insulated for protecting the operator The TSN wrench is DN a then preset to the customers requirements and the handle end is P T TAY ioo Votis effectively sealed using a heat shrink end cap hot m
Download Pdf Manuals
Related Search