Operating instructions OSRAM OUTDOOR sensor
Contents
1. OSRAM OUTDOOR Light and motion sensor Operating instructions XII 2009 OUTDOOR_ba0912en_we1 02 indd OSRAM GmbH Kunden Service Center Customer Service Center CSC Steinerne Furt 62 86167 Augsburg Germany Tel 49 0 1803 677 200 kostenpflichtig charges apply Fax 49 0 1803 677 202 www osram com www osram de 4008321957061 Description Purpose and application The OUTDOOR sensor detects the presence of persons and measures the intensity of ambient light It is ideally suited for indoor and outdoor light applications that require a high level of protection against outdoor weather condi tions wetness dirt The sensor is designed for wall and ceiling installation Function The sensor works fully automatically and is used for contact free switching The values detected by the sensor motion light value control the switching behaviour on the basis of the settings created by the user The following settings can be made e Delay if no motion is detected e Light switching threshold e Operating mode Design The sensor is made up of the following components e Light and motion sensor with an integrated LED A e Buttons S1 and S2 B e Swivel arm C e Connection box D Operation Initial startup During initial startup the initialisation for the functional check and sensor calibration is started e The luminaires are switched on for approx 2 s e The red LED2. inside the lens flashes until the sensor automatically switches to test mode after max 45 s see Executing the test mode e After the test mode is ended the sensor switches to normal mode see Operating modes Operating modes Normal operation After initial startup or a reset the sensor goes into normal mode for light and motion dependent switching with the following default settings e Light switching threshold 7 lux e Delay 2 minutes The default settings can then be changed individually Reset Press buttons S1 and S2 simultaneously for at least 6 s Confirmation The LED flashes 2x Pulse mode The pulse mode is available with a fixed delay for controlling ex ternal time switches see Activating deactivating pulse mode Page 1 of 4 Operation cont S1 S2 Control principle normal mode Luminaire OFF Artificial light required yes Luminaire ON i Luminaire af 5 s 30 min p Luminaire no OFF Luminaire Artificial light required no Vv oi Setting the light switching theshold Setting of the light switching threshold at which the load is switched on or off as a function of the measured light value default setting 7 lux If the light switching threshold is deactivated the connected load is switched on whenever motion is detected independent of the measured light value Changing the light switching threshold Q Pre
3. ram in the fitting instructions The device is functional but the switching functions are not being carried out Is the initialisation process finished See Performing an initialisation Is the light switching threshold set correctly See Setting the light switching threshold Is the detection area set correctly See Setting the detection area in the fitting instructions Is the correct operating mode normal mode pulse mode set See Normal mode and reset and Activating deactivating the pulse mode Page 3 of 4 Appendix Technical data Operating voltage 230 V AC 50 60 Hz Switch output load capacity Incandescent lamp 2300 W HV halogen lamps 1500 W Fluorescent lamps 1000 VA Inductive load 600 VA Max number of ECGs 5x QT FQ 2x80 or QTP5 1x80 or QTP5 2x54 7X QTP5 2x14 35 or QTP5 1x54 9x QTP5 1x14 35 5x QTP8 2x58 9x QTP8 1x58 5x QT FIT8 2x58 or QT FIT8 2x36 9x QT FIT8 1x58 or QT FIT8 1x36 5x QTi 2x35 49 80 10x QTi 2x28 54 14x QTi 1x28 54 30 C 70 C Protection type IP 55 Operating temperature Dimensioned drawing f4mm 10mm 6mm The Low Voltage Directive has been complied with according to EN 60669 2 1 Conformity with the relevant EU directives is confirmed by the CE symbol Page 4 of 4
4. ss button S1 briefly The current light value measurement is stored as the light switching threshold Confirmation The LED flashes 1x Deactivating activating the light switching threshold Press button S1 for at least 2 s Confirmation The LED flashes 2x When the light switching threshold is deactivated the LED flashes briefly every 5 s Setting the delay The switch off delay time in normal mode when no motion is detected default setting 2 min Press button S2 briefly The LED begins flashing Press button S2 again briefly after a delay of T 5 s 30 min The LED goes out T is stored as the delay time Page 2 of 4 Operation cont Activating deactivating the pulse mode The pulse mode enables the control of external time switches such as stairwell time switches When the light value drops below the light switching threshold and motion is detected the luminaires are switched on for 1 s and motion detection is deactivated for 9 s Press button S2 for at least 2 s Confirmation The LED flashes 2x Executing the test mode checking motion detection In the test mode the parameters are optimised for a rapid check of the motion detection When motion is detected the luminaires are switched on for 1 s and then switched off for 2 s The light switching threshold is deactivated Note During initial startup the test mode is automatically started after initialisation To start the tes
5. t mode Simultaneously press buttons S1 and S2 for 3 5 s until the LED lights up continuously Confirmation The LED flashes 2x Check the motion detection and adjust the detection area if necessary see the fitting instructions The test mode is ended automatically after 10 min To end the test mode earlier Press button S1 or S2 briefly Switching luminaires manually Precondition Normal mode the pushbutton switch is connected see the connection diagram in the fitting instructions To switch on e For the duration of delay T Press the pushbutton switch briefly 2 Confirmation The LED lights up continuously e For 4 hours Press the pushbutton switch 2x briefly To switch off Press the pushbutton switch briefly Manual initialisation The initialisation is used for the functional check and sensor calibration Precondition Normal mode the pushbutton switch is connected see the connection diagram in the fitting instructions Press the pushbutton switch for at least 2 s Confirmation The luminaires are switched on for 2 s and the LED flashes for max 45 s Note The initialisation is performed automatically during initial startup or after every power failure of at least 3 s Troubleshooting If you cannot remedy the fault please contact the customer service department of the manufacturer The device is not functional Is there power and is the device connected correctly See Connection diag
Download Pdf Manuals
Related Search