A0620176 Meteor-175RGB Underwater Pool Light Operating
Contents
1. Fixing Screws ae High grade polycarbonate glass optical window 1 Optical window High grade polycarbonate glass optical window 2 Underwater pool light casing Stainless steel casing with fixing holes and cable gland 3 Cable The 4 pole multi core cable to connect the 12 24Vdc power supply and optional remote control or switch 4 Fixing screw The fixing screws to fix the underwater pool light on the wall INSTALLATION The underwater light kit consists of the following components e Underwater Light METEOR 175 RGB e 4 x fixing screw 5 5x38 with wallplugs e Operating Instructions The METEOR 175 RGB has to be installed on a flat surface on the pool wall under water line Do not try to install the underwater pool light while the pool is filled with water When the installation is finished briefly test the underwater light prior to fill the pool with water The installation have to be realized by a qualified personnel Wall Sealing Grooves 2X Note Avoid using the underwater pool light out of the water for more than 2 minutes The underwater pool light is protected by a temperature sensor against over heating When the temperature of the underwater pool light exceeds 85 C the underwater pool light is automatically switched off Wall preparation The underwater pool light is recommended to be installed around 0 2 m below the waterline for the best illumination and to avoid over heating To fix the under2. with the instructions of this manual only e The power supply has to be disconnected before installation e The underwater pool light is recomended to be installed around 0 2 m below the water line for the best illumination and to avoid over heating e The optical window must be clear and not covered by any kind of isolating or other material The optical window has to be cleaned with a mild soap or detergent and lukewarm water by using a soft cloth or sponge Do not use abrasive or highly alkaline cleaners e Never scrape with razor blades or other sharp instruments Benzene leaded gasoline acetone or carbon tetrachloride should never be used e Do turn power off immediately and refer servicing to qualified service personnel if the underwater pool light does not operate normally following the operating instructions FEATURES APPEARANCE Innovative DesignS Stainless Steel Ultra thin Casing 36 Power LEDs Design 2 White Blue Green or Multi Color RGB Lighting High Grade Polycarbonate Glass Optical Window Vacuum Metalized Reflector Remote Control Digital Dimming Polarity Protection Transient Protection Thermal Protection Wide Range Power Supply Low Power Consumption Simple Installation Optional accessories for different pools installations 5m 4 Pole Multicable pog Powersupply DC Black Powersupply DC Orange Pulse Control Brown Pulse Control GND Stainless Steel 316L stainless steel 316L
3. ie LED technology ART A0620176 Meteor 175RGB Underwater Pool Light Operating Instructions CONTENTS EENE O e A ERA E AE EAE E E EEE ERBE EEERESLTEHERE EELFENE LEERE EENT 3 Features oorner a a sa a iaeaea EES aE RAEE EEE E Ee ADES ea ea EEE a ERa SOE EEOAE EENE 3 SAKETE UiO IN E E N E EE E ee ET 3 Components and Conneclors ran ende eher ea e a a i e aapa 4 Installation 2 as en nenn EENE aN 5 EEIN 1 0 a vst oes EEE EEE ics Oe SETEUEE EHE ERFEEOELEEPEPEUEFEOLEEE RE Gs ean asa aso etn wade ab Ane teed hed dae eR Ae 7 AAD PCAN ANCES E E E E A EE EE ETA E E E E E E E E E 8 Technical Specifications sierra E A A EEEE E EE EE NES 8 PREFACE The METEOR 175 RGB ultra thin underwater pool light with built in driver is designed to use the latest LED lighting technology The surface mount designed casing enable very simple installation on the flat surface without any surface preparation during construction and the max diameter of the hole through the wall is 8 mm The METEOR 175RGB with 316T stainless steel casings is available with RGB colors with 36 highpower LEDs The multi color RGB version allows changing of the color of lighting manually or automatically through the complete rainbow spectrum The most advanced electronic design with built in microprocessor enables network connection and simple control of complete group of lights with dimming PRECAUTIONS e The underwater pool light has to be installed and used in accordance
4. key switch not included has to be used and connected to the CONTROL wires by the 2 pole signal cable not included METEOR 175 RGB Sequence of lighting Custom Color CONTROLS Remote control has to be used to turn on and turn off the underwater Full RGB pool light and to control the mode of lighting and luminosity Cool White The multi color underwater pool light can be controlled by using the key switch Bluish White J Red When the light is turned off the color or mode of lighting can be Green changed sequentially by pressing the momentary switch for 2 Blue seconds Rainbow Color Spectrum Puls dim controller 230V AC LED 12 24V Power Supply Turning on off Press the key switch momentary Changing the color or mode of lighting When the light is turned off press the key switch for 2 seconds Setting the Custom Color At the selected Rainbow Color Spectrum mode press the key switch momentary to turn the light off After that press the key switch for 5 seconds or until the light is switched to the selected color and then the Custom Color is set and selected Dimming When the light is turned on press the key switch until the desired illumination is achieved By another pressing of the key switch the luminosity will increase to the maximum illumination Set default Press the key switch for min 40 seconds or until the light is turned off Synch
5. ronization When more than one multi color underwater pool light is connected to the system the optional Synchronization Unit LSU08 is recommended to synchronize the colors of lighting at the Rainbow Color Spectrum mode of lighting On the other case the colors of all installed lights would not be the same after few minutes or hours of operation in the Rainbow Color Spectrum mode If the multi color light is used only with one of the fixed color of lighting the synchronization is not necessary TECHNICAL SPECIFICATIONS Power supply 24 Vdc max 3 4A 24 Vdc Lens angle 60 Optical window High grade polycarbonate glass Luminous flux max 7000 Lm Operating temperature 10 C 40 C Casing Stainless steel 316L Protection IP68 Dimensions 176x17mm Weight 2 3 kg Highlite international BV Vestastraat 2 NL 6468 EX Kerkrade The Netherlands ARTECTA Division Phone 31 0 45 5667734 Fax 31 0 45 5667709 Per E Mail artecta highlite nl Design and specifications subject to change without notice
6. water pool light with screws 5 5x38 the diameter of holes drilled into the wall has to be 8mm The diameter of the hole for cable gland drilled through the wall has to be 8 mm Sealing Before inserting the cable with gland through the hole the sealant has to be used into the grooves around the four fixing holes and around the gland in the rear surface of the underwater pool light The sealant can be on silicon basis but the best solution is two component polymer sealant Fixing The underwater light has to be fixed with four screws 5 5x38 with wallplugs Note Do not overtighten the screws as this can result in underwater pool light damage Earthing The underwater pool light has to be earthed by using a pre tinned green wire with a yellow stripe a minimum of 8 AWG 8 36 mm2 The wire has to be connected to the underwater pool light by the help of one fixing screw 5 5x38 Connection The power supply has to be connected through the main switch not included with correct polarity and protected by a fuse not included The power supply voltage has to be from 10 30Vdc Note e The power supply has to be switched off before installation e The underwater light has to be connected as described in the table below METEOR 175 RGB FUNCTION wire color Red DC Power Supply Black GND Power Supply Orange Control Brown GND Control Remote control connection To control the mode of lighting the simple
Download Pdf Manuals
Related Search