A0620140 Meteor-140W Underwater Pool Light Operating Instructions
Contents
1. Stainless steel casing with fixing holes and cable gland 3 Cable The 4 pole multi core cable to connect the 12 24Vdc power supply and optional remote control or switch 4 Fixing screw The fixing screws to fix the underwater pool light on the wall INSTALLATION The underwater light kit consists of the following components e Underwater Light METEOR 140 e 4 x fixing screw 5 5x38 with wallplugs e Operating Instructions The METEOR 120 has to be installed on a flat surface on the pool wall under water line Do not try to install the underwater pool light while the pool is filled with water When the installation is finished briefly test the underwater light prior to fill the pool with water The installation have to be realized by a qualified personnel Sealing Wall Screw 5 5X38 Sealing Grooves 2X Note Avoid using the underwater pool light out of the water for more than 2 minutes The underwater pool light is protected by a temperature sensor against over heating When the temperature of the underwater pool light exceeds 85 C the underwater pool light is automatically switched off Wall preparation The underwater pool light is recommended to be installed around 0 2 m below the waterline for the best illumination and to avoid over heating To fix the underwater pool light with screws 5 5x38 the diameter of holes drilled into the wall has to be 8 mm The diameter of the hole for cable gland drilled through the2. Meteor 120 Meteor 140 Meteor 140 Meteor 140 ON OFF Switch LED 12 24V Power Supply 230V AC Note If the remote control is not used for dimming operation the both CONTROL wires have to be bridged and insulated or connected to the GND Meteor 120 Meteor 120 Meteor 120 Meteor 120 Meteor 120 Meteor 120 Meteor 140 Meteor 140 Meteor 140 Meteor 140 Meteor 140 Meteor 140 HJ HI A9915200 LDU13 ON heden 234567 8 SW1 If connected the METEOR 120 CONTROL _ DC IN or METEOR 140 fixtures all switches must be ON ON AAA 12345678 ovac SW2 Switch more switches to ON to adjust the minimal dimming value Each step is 12 1 For dimming Meteor series of underwater LED lights use the LDU PWM Dimmer The 3 control outputs enable the dimming of 3 groups of underwater LED lights by using of one push button switch Turning ON OFF Press the key switch momentary Dimming When the light is turned on press the key switch until the desired illumination is achieved By another pressing of the key switch the luminosity will increase to the maximum illumination CH 3 CH 2 CH 1 in ET aan OE ned Meteor 120 Meteor 120 Meteor 100 Meteor 100 Meteor 140 Meteor 140 CS ECS CS EC SW1 Adjust the PWM f
3. e to which this declaration relates complies with the above mentioned S ildiz Nov 29 2011 standards and Directives ie ae ee AK Highlite International BV ZAN Vestastraat 2 6468 EX Kerkrade A The Netherlands Signature of representative 9 abe
4. ie LED technology ART A0620140 Meteor 140W Underwater Pool Light Operating Instructions CONTENTS PISIACS nisinsin aeaa ie i a aaa dend dealen eene eea nds daden ante 2 Precautions annen Antena te aaneen denudata reden eeen elan ademend 2 FeatUr S na nertenketinesnsi ana iten a E E N A gl edt betert anke ease eenen eren ada N 3 Components and Cable connection nonnen rna a ahea taa aR EEE RENREN EREE 3 INSTAN ALON seriei E a e i ai a E aa 4 5 7 8 Technical Specifications s serioses a a nasa lan ia aa a a panelen e iE daan neede 6 Bees gelieerde org lola g gele AE 9 PREFACE The METEOR 140W compact ultra thin underwater pool light with built in driver is designed to use the latest LED lighting technology The surface mount designed casing enable very simple installation on the flat surface without any surface preparation during construction and the max diameter of the hole through the wall is 8 mm The METEOR 140W is available in stainless steel casings with 36 warm white highpower LEDs The most advanced electronic design with built in microprocessor enables network connection and simple control of complete group of lights with dimming PRECAUTIONS e The underwater pool light has to be installed and used in accordance with the instructions of this manual only e The power supply has to be disconnected before installation e The underwater pool light is recomended to be installed around 0 2 m below the water l
5. ine for the best illumination and to avoid over heating e The optical window must be clear and not covered by any kind of isolating or other material The optical window has to be cleaned with a mild soap or detergent and lukewarm water by using a soft cloth or sponge Do not use abrasive or highly alkaline cleaners e Never scrape with razor blades or other sharp instruments Benzene leaded gasoline acetone or carbon tetrachloride should never be used e Do turn power off immediately and refer servicing to qualified service personnel if the underwater pool light does not operate normally following the operating instructions FEATURES APPEARANCE e Innovative DesignS e tainless Steel Ultra Thin Casing e 36 Power LEDs Design e White Blue Green or Multi Color RGB Lighting e High Grade Polycarbonate Glass Optical Window e Vacuum Metalized ReflectoR e Remote Control e Digital Dimming e Polarity Protection 9 e Transient Protection 8 e Thermal Protection e Wide Range Power Supply e Low Power Consumption e Simple Installation e Optional accessories for different pools installations 3 5m 4 Pole Multicable Red Powersupply DC Black Powersupply DC Orange Pulse Control Brown Pulse Control GND Stainless Steel 316L stainless steel 316L Fixing Screws ae High grade polycarbonate glass optical window 1 Optical window High grade polycarbonate glass optical window 2 Underwater pool light casing
6. requency of dimming for different series LED underwater fixtures O 12345678 SW2 Switch more switches to ON to adjust the minimal dimming value Each step is 12 1 oT LED 12 24V lS DC Power supply For dimming Meteor series of underwater LED lights use the LDU PWM Dimmer The 3 control outputs enable the dimming of 3 groups of underwater LED lights by using of one push button switch It is possible to control 3 different groups of underwater lights for example Meteor 100 amp Meteor 120 amp Meteor 140 Turning ON OFF Press the key switch momentary Dimming When the light is turned on press the key switch until the desired illumination is achieved By another pressing of the key switch the luminosity will increase to the maximum illumination a DECLARATION OF CONFORMATY Supplier Details Name Highlite International BV Address Vestastraat 2 6468EX Kerkrade The Netherlands Product Details Product Name Meteor 140 W Ordercode A0620140 Trade Name Artecta Applicable Standards Details 1 EMC Directives 2004 108 EC EN 55015 2006 A1 2007 EN 61547 1995 A1 2000 A2 2009 EN 61547 2009 2 Low Voltage Directives 2006 95 EC EN 60598 1 2004 A1 2006 Supplementary information The conformity to above standards is verified by Astel d o o hereby declare under our sole responsibility Name Issued Date that the product mentioned abov
7. switch not included can be used and connected to the CONTROL wires by a 2 pole signal cable not included Note Ifthe remote control is not used at single color models for normal operation the both CONTROL wires have to be bridged and insulated or connected to the GND Turning on off Press the key switch momentary Dimming When the light is turned on press the key switch until the desired illumination is achieved By another pressing of the key switch the luminosity will increase to the maximum illumination Set default Press the key switch for min 40 seconds or until the light is turned off Puls dim controller LED 12 24V Power Supply 230V AC TECHNICAL SPECIFICATIONS Power supply Advised Powersupply 12Vdc Advised Powersupply 24Vdc Lens angle Optical window Luminous flux White color temperature Operating temperature Casing Protection Dimensions Weight Design and specifications subject to change without notice 12 24 Vdc max 4 3A 12 Vdc max 1 9mA 24 Vdc PLN 100 A9900352 PLN 100 A9900362 60 High grade polycarbonate glass 3900 Lm 3 000K 10 C 50 C Stainless steel 316L IP68 139 x 9 mm 0 8 kg Highlite international BV Vestastraat 2 NL 6468 EX Kerkrade The Netherlands ARTECTA Division Phone 31 0 45 5667734 Fax 31 0 45 5667709 E Mail artecta highlite nl One color lights Meteor 120 Meteor 120
8. wall has to be 8 mm Sealing Before inserting the cable with gland through the hole the sealant has to be used into the grooves around the four fixing holes and around the gland in the rear surface of the underwater pool light The sealant can be on silicon basis but the best solution is two component polymer sealant Fixing The underwater light has to be fixed with four screws 5 5x38 with wallplugs Note Do not overtighten the screws as this can result in underwater pool light damage 4 Earthing The underwater pool light has to be earthed by using a pre tinned green wire with a yellow stripe a minimum of 8 AWG 8 36 mm2 The wire has to be connected to the underwater pool light by the help of one fixing screw 5 5x38 Connection The power supply has to be connected through the main switch not included with correct polarity and protected by a fuse not included The power supply voltage has to be from 10 30Vdc Note e The power supply has to be switched off before installation The underwater light has to be connected as described in the table below METEOR 140W FUNCTION wire color Red DC Power Supply Black GND Power Supply Orange Control Brown GND Control Controls Remote control can be used to turn on and turn off the underwater pool light and to control the luminosity Remote control connection To remotely turn on and turn off the underwater pool light the simple
Download Pdf Manuals
Related Search