A0620110 Meteor-100W Underwater Pool Light Operating Instructions
Contents
1. Fax 31 0 45 5667709 E Mail artecta highlite nl One color lights 1 Meteor 100 Meteor 100 Meteor 100 ON OFF Switch 230V AC LED 12 24V Power Supply Note If the remote control is not used for dimming operation the both CONTROL wires have to be bridged and insulated or connected to the GND Meteor 100 Meteor 100 Meteor 100 Meteor 100 Meteor 100 Meteor 100 A9915200 LDU13 in SW 1 If connected the METEOR 100 fixtures all switches must be OFF 0 eee iy Puls dim 234567 8 4 LED 12 24V 230V AC DC Power supply SW2 Switch more switches to ON to adjust the minimal dimming value Each step is 12 1 For dimming Meteor series of underwater LED lights use the LDU PWM Dimmer The 3 control outputs enable the dimming of 3 groups of underwater LED lights by using of one push button switch Turning ON OFF Press the key switch momentary Dimming When the light is turned on press the key switch until the desired illumination is achieved By another pressing of the key switch the luminosity will increase to the maximum illumination One color lights 3 CH 3 CH 2 CH 1 ae Se ia Meteor 120 Meteor 120 Meteor 100 Meteor 100 Meteor 140 Meteor 140 SEH GDoO CH OS A9915200 LDU13 Lo IL O s golat E Gi 2345678 SW1 Ad2. assumes no liability for incidental or consequential damages of any kind including damages arising from collision with other vessels or objects
3. e multi core cable to connect the 12 24Vdc power supply and optional remote control or switch 4 Fixing screw The fixing screws to fix the underwater pool light on the wall INSTALLATION The underwater light kit consists of the following components e Underwater Light METEOR 100 e 4 x fixing screw 5 5x38 with wallplugs e Operating Instructions with Declaration of Conformity and Warranty conditions The METEOR 100 has to be installed on a flat surface on the pool wall under water line Do not try to install the underwater pool light while the pool is filled with water When the installation is finished briefly test the underwater light prior to fill the pool with water The installation have to be realized by a qualified personnel Sealing Wall Screw 5 5X38 Sealing Grooves 2X Note Avoid using the underwater pool light out of the water for more than 2 minutes The underwater pool light is protected by a temperature sensor against over heating When the temperature of the underwater pool light exceeds 85 C the underwater pool light is automatically switched off Wall preparation The underwater pool light is recommended to be installed around 0 2 m below the waterline for the best illumination and to avoid over heating To fix the underwater pool light with screws 5 5x38 the diameter of holes drilled into the wall has to be 8 mm The diameter of the hole for cable gland drilled through the wall has to be 8 mm Seali
4. ie LED technology ART A0620110 Meteor 100W Underwater Pool Light Operating Instructions CONTENTS Preface n ie a enge en rue 2 Precautions meere a e ar Bee sess sassheiuaentasauasodee sesh ssunl chulenutessadaaseescasdessensteamseet ents 2 Features erahnen nern nenn einen naar Renee E eeee 3 Components and Cable connection 44enee rna a nahea taa aR EEEE ERREEN EREE 3 Installation sa ua ae ann a anni 4 5 7 8 Technical Specifications s smerissen lub 6 Declaration 0f conformaty sasian annain ni aia i Ea nea a e aAa A e AAEE ERSE EAEEREN 9 PREFACE The METEOR 100W compact ultra thin underwater pool light with built in driver is designed to use the latest LED lighting technology The surface mount designed casing enable very simple installation on the flat surface without any surface preparation during construction and the max diameter of the hole through the wall is 8 mm The METEOR 100W is available in stainless steel casings with 6 warm white highpower LEDs The most advanced electronic design with built in microprocessor enables network connection and simple control of complete group of lights with dimming PRECAUTIONS e The underwater pool light has to be installed and used in accordance with the instructions of this manual only e The power supply has to be disconnected before installation e The underwater pool light is recomended to be installed around 0 2 m below the water line for the bes
5. just the PWM frequency of dimming for different series LED underwater fixtures O TELLIT EA 12345678 4 LED IZAN en 230V AC SW2 Switch more switches to ON to adjust the minimal dimming value Each step is 12 1 For dimming Meteor series of underwater LED lights use the LDU PWM Dimmer The 3 control outputs enable the dimming of 3 groups of underwater LED lights by using of one push button switch It is possible to control 3 different groups of underwater lights for example Meteor 100 amp Meteor 120 amp Meteor 140 Turning ON OFF Press the key switch momentary Dimming When the light is turned on press the key switch until the desired illumination is achieved By another pressing of the key switch the luminosity will increase to the maximum illumination gt DECLARATION OF CONFORMATY Supplier Details Name Highlite International BV Address Vestastraat 2 6468EX Kerkrade The Netherlands Product Details Product Name Meteor 100 W Ordercode A0620110 Trade Name Artecta Applicable Standards Details 1 EMC Directives 2004 108 EC EN 55015 2006 A1 2007 EN 61547 1995 A1 2000 A2 2009 EN 61547 2009 2 Low Voltage Directives 2006 95 EC EN 60598 1 2004 A1 2006 Supplementary information The conformity to above standards is verified by Astel d o o Declaration hereby declare under our sole responsibility Name I
6. ng Before inserting the cable with gland through the hole the sealant has to be used into the grooves around the four fixing holes and around the gland in the rear surface of the underwater pool light The sealant can be on silicon basis but the best solution is two component polymer sealant Fixing The underwater light has to be fixed with four screws 5 5x38 with wallplugs Note Do not overtighten the screws as this can result in underwater pool light damage Earthing The underwater pool light has to be earthed by using a pre tinned green wire with a yellow stripe a minimum of 8 AWG 8 36 mm2 The wire has to be connected to the underwater pool light by the help of one fixing screw 5 5x38 Connection The power supply has to be connected through the main switch not included with correct polarity and protected by a fuse not included The power supply voltage has to be from 10 30Vdc Note e The power supply has to be switched off before installation e The underwater light has to be connected as described in the table below METEOR 100W FUNCTION wire color Red DC Power Supply Black GND Power Supply Orange Control Brown GND Control Controls Remote control can be used to turn on and turn off the underwater pool light and to control the luminosity Remote control connection To remotely turn on and turn off the underwater pool light the simple switch not included can be u
7. p the equipment will be repaired or replaced at the Warrantor s option without charge and returned to the Purchaser at the Warrantor s expense d no refund of the purchase price will be granted to the Purchaser unless the Warrantor is unable to remedy the defect after having a reasonable number of opportunities to do so Prior to refund of the purchase price Purchaser must submit a statement in writing from a professional boating equipment supplier that the installation instructions of the Operating Instructions manual have been complied with and that the defect remains e warranty service shall be performed only by the Warrantor or an authorized distributor and any attempt to remedy the defect by anyone else shall render this warranty void 5 There shall be no warranty for defects or damages coused by faulty installation or hook up abuse or misuse of the equipment including exposure to excessive heat salt or fresh water spray or water immersion except for equipment specially designed as waterproof 6 There shall be no responsibility or liability whatsoever on the part of the Warrantor or its employees and representatives for injury to any person or persons or damage to property loss of income or profit or any other consequential or resulting damage or cost which may be claimed to have been incurred through the use or sale of the equipment including any possible failure or malfunction of the equipment or part thereof 7 The Warrantor
8. sed and connected to the CONTROL wires by a 2 pole signal cable not included Note Ifthe remote control is not used at single color models for normal operation the both CONTROL wires have to be bridged and insulated or connected to the GND Dimming The dimming are enabled by using optional PWM dimmer LDU13 DMX512 control The network connection to control the lights with the standard DMX512 protocol is enabled by using optional PWM dimmer LDU13 and optional LXUO1 or LXUOS3 interfaces Turning on off Press the key switch momentary Dimming When the light is turned on press the key switch until the desired illumination is achieved By another pressing of the key switch the luminosity will increase to the maximum illumination Set default Press the key switch for min 40 seconds or until the light is turned off TECHNICAL SPECIFICATIONS Power supply Advised Powersupply 12Vdc Advised Powersupply 24Vdc Lens angle Optical window Luminous flux White color temperature Operating temperature Casing Protection Dimensions Weight Design and specifications subject to change without notice 12 24 Vdc max 680 mA 12 Vdc max 380 mA 24 Vdc PLN 30 A9900350 PLN 30 A9900360 60 High grade polycarbonate glass 650 Lm 3 000K 10 C 50 C Stainless steel 316L Highlite international BV Vestastraat 2 NL 6468 EX Kerkrade The Netherlands ARTECTA Division Phone 31 0 45 5667734
9. ssued Date that the product mentioned above to which this declaration relates complies with the above mentioned S ildiz April 22 2011 standards and Directives m SE N Highlite International BV yA S Vestastraat 2 6468 EX Kerkrade The Netherlands WARRANTY 1 The equipment is warranted by ARTECTA to be free from defects in workmanship and materials under normal use and service 2 This Warranty is in effect for of two years from the date of purchase by the user Proof of purchase must be included to establish that it is inside the warranty period 3 This Warranty is transferrable and covers the product for the specified time period 4 In case any part od the equipment proves to be defective other than those parts excluded in paragraph 5 below the owner should do the following a prepare a detailed written statement of the nature and circumstances of the defect to the best of the Owner s knowledge including the date of purchase the place of purchase the name and adress of the installer and the Purchaser s name adress and telephone number b the Owner should return the defective part or unit along with the statement referenced in the preceding paragraph to the warrantor ARTECTA or an authorized ARTECTA distributor postage shipping prepaid and at the expense of the Purchaser c if upon the Warrantor s or authorized distributor s examination the defect is determined to result from defective material or workmanshi
10. t illumination and to avoid over heating e The optical window must be clear and not covered by any kind of isolating or other material The optical window has to be cleaned with a mild soap or detergent and lukewarm water by using a soft cloth or sponge Do not use abrasive or highly alkaline cleaners e Never scrape with razor blades or other sharp instruments Benzene leaded gasoline acetone or carbon tetrachloride should never be used e Do turn power off immediately and refer servicing to qualified service personnel if the underwater pool light does not operate normally following the operating instructions FEATURES APPEARANCE Innovative Design Stainless Steel Ultra Thin Casing 6 High Power warm white LED s High Grade Polycarbonate Glass Optical Window Vacuum Metalized Reflector Remote Control Digital Dimming Polarity Protection Transient Protection Thermal Protection Wide Range Power Supply Low Power Consumption Simple Installation 8 Optional accessories for different pools installations 5m 4 Pole Multicable pog Powersupply DC Black Powersupply DC Orange Pulse Control Brown Pulse Control GND Stainless Steel 316L stainless steel 316L Fixing Screws ae High grade polycarbonate glass optical window 1 Optical window High grade polycarbonate glass optical window 2 Underwater pool light casing Stainless steel casing with fixing holes and cable gland 3 Cable The 4 pol
Download Pdf Manuals
Related Search