Narrowstick Installation Manual
Contents
1. This Product contains high intensity LED devices To prevent eye damage Blue Yellow Grey Green Violet Tan Orange Brown Tee ESE DRIVER SIDE PASSENGER SIDE STANDARD REAR FACING MOUNTING 3 we pen Input Cable Blue Yellow Grey Green Violet Tan Orange Brown Ele z Do o o e o F no gt Zo a o yo o o ETJE EME EA EA EA ENT MEAN PASSENGER OPTIONAL FRONT FACING MOUNTING DRIVER SIDE SIDE Input Cable 11 Wire Cable Wire Designations RED RED WHITE Narrowstik LC Stik Power 12V WHITE DIM Control wire BROWN ORANGE TAN INDIVIDUAL VIOLET L E D MODULE CONTROL WIRES GREEN SEE FIGURE 5 GREY YELLOW BLUE Rear Facing Ox a System System Figure 5 LED Narrowstik LC Stik wire designations for front rear facing mounting Connecting An 11 wire LED Narrowstik cable to a 5 Output Control Head or RLS System It may be necessary to retrofit the new 11 wire cable to a 5 output control system The required connections are shown below in Fig 6 to connect a 5 output control head or a 5 output RLS Stand alone LED Narrowstiks and internal Lightbar LED Narrowstiks will follow the same wire designations Refer to the 5 output control head user manual or RLS manual for control head operation New Standard 11 Wire Cable2. be enabled Dual Color LC Stik models To enable the Red Blue half of the dual color heads touch the White wire to ground To disable the red blue half of the dual color heads when the control head is active you will need the LC Stik override circuit S81499 which is included with all dual color LC Stik models When installed this module will disable the red blue half of the LC Stik See the override circuit manual for specific wiring details Note The White wire on a dual color LC Stik module is not for dimming There is no dimming feature on an LC Stik Dimming All Narrowstik models come equipped with a DIM low power mode as standard that allows the user to reduce the L E D intensity if desired The current consumption is also significantly reduced in this mode approximately 60 Dim mode is controlled by the White wire in the 11 wire cable see figure 5 page 5 When 12V is applied to this white wire the modules will DIM until removed The Narrowstik control head has an output dedicated to provide this 12V see the Control Head manual for details Note This feature is not available on LC Stik models effectiveness of them especially in brightly lit areas Failure to use adequate light for the circumstances can cause motorists to WARNING fail to see the emergency vehicle and lead to serious personal injury or death The Dim setting reduces the light output of emergency warning lights reducing the Never use the DIM se
3. is highly recommended that terminal blocks or soldered connections be used with shrink tubing to protectthe connections Do not use insulation displacement connectors e g 3M Scotchlock type connectors Route wiring using grommets and sealant when passing through compartment walls Minimize the number of splices to reduce voltage drop High ambient temperatures e g underhood will significantly reduce the current carrying capacity of wires fuses and circuit breakers Use SXL type wire in engine compartment AN All wiring should conform to the minimum wire size and other recommendations of the manufacturer and be protected from moving parts and hot surfaces Looms grommets cable WARNING ties and similar installation hardware should be used to anchor and protect all wiring Fuses or circuit breakers should be located as close to the power takeoff points as possible and properly sized to protect the wiring and devices Particular attention should be paid to the location and method of making electrical connections and splices to protect these points from corrosion and loss of conductivity Ground terminations should only be made to substantial chassis components preferably directly to the vehicle battery The user should install a fuse sized to approximately 125 of the maximum Amp capacity in the supply line to protect against short circuits For example a 30 Amp fuse should carry a maximum of 24 Amps DO NOT USE 1 4 DIAMETER GLASS FUSES AS TH
4. Designations Existing 7 Wire Cable RED RED WHITE Power 12V wires DREION R DI WHITE Power 12V wires WHITE LED DIM Control BROWN BROWN ORANGE ORANGE Individual LED control TAN Individual VIOLET Wires VIOLET LED Control YELLOW Wires BLUE GREEN GREY YELLOW BLUE RLS 5 Output Connections NASLDC 5 Output Control Head Connections As shown the Orange and Tan Violet and Green and the Grey and Yellow wires will need to be paired into each single output as indicated Note that the each wire shown with two color designations is actually representing two individual wires into a single output Fig 1 Wiring for Narrowstik LC Stik models with outboard flashing modules When independently flashing modules are selected to replace the standard modules in the outboard positions the BLUE and the Brown wires will be used to activate these modules and will not be connected to the Blue Brown outputs on the control head as usual Instead the Blue positive wire can be connected to 12V and the Brown negative wire can be connected to the AUX output on the control head When the AUX button is activated the flashing modules will be enabled Refer to the control head manual for further details on use of the AUX function Alternatively the Blue positive wire can be connected through a switch to 12V and the Brown negative wire can connected to ground When the switch is closed the Flashing modules will
5. EY ARE NOT SUITABLE FOR CONTINUOUS DUTY IN SIZES ABOVE 15 AMPS Circuit breakers are very sensitive to high temperatures and will false trip when mounted in hot environments or operated close to their capacity 1 After installing the Narrowstik LC Stik route the 11 wire cable into the vehicle to where the control head will be mounted 2 Cut the cable to length and strip back the cable insulation on the 11 wire cable 3 Connect the red and red white wires inthe 11 wire cable to the positive 12V side of the battery through a user supplied 15 amp fuse or breaker using an 16 gauge minimum wire or larger 4 Route a minimum 16 gauge black wire to the battery negative ground earth Use the 1 4 insulated quickslide located in control head parts bag and connect the black 16 gauge wire control head 5 Remove the 14 position terminal plug from the back of the control head Connect the remaining wires in the 11 wire cable to the plug as shown in Figure 5 page 5 Connect power to the control head See control head manual for auxiliary wire functions Note When installing the Narrowstik LC Stik as a Front Facing system or if it is desired to have the cable exit from the Passenger side the LED module control wires will be reversed See Figure 5 page 5 for details 6 Check all connections for frayed or shorted wires Insert the plug back into the Narrowstik control head DO NOT stare into light beam at close range WARNING
6. INSTALLATION a OPERATION MANUAL NASL547 39 NASL847 39 NAS3547 39 NAS3847 39 NarrowStik LCC547 39 LC847 39 LC Stik 3 Up OPTIX NARROWSTIK 3 Inc a subsidiary of Pubie Safety Equipment Inc VA LIC SAFETY EQUIPMENT LED NarrowStik LED LC Stik Contents Introduction with warnings 2 Models caused 2 Unpacking 8 Pre installation 2 Installation amp Mounting een 3 Permanent Mounting sense 3 Code 3 LP 6000 Series Frame 3 Code 3 XL 5000 Series Frame 3 Wiring INStrUCIONS seen 4 7 So PECHE CONS nn 7 Maintenance een 8 Troubleshooting rear 8 NOIES tet da doi ca 9 11 Warranty elt n n ee 12 M P O RT AN T Read all instructions and warnings before installing and using N RIES This manual must be delivered to the end user of this equipment Introduction The LED NarrowStik and the LC Stik are both traffic directing devices that will mount in many locations including the back of a lightbar or rear panel of a truck Each Stik is a series of lights that point traffic away from the scene of an accident or work site The LED NarrowStik option utilizes state of the art High Flux LED lightheads The LC Stik utilizes more economical and less bright Superflux LEDs These lightheads last longer and use much less current than standard incandescent lamps The use of this or any warning device does not insure that all driv
7. Not reduce the output performance of the system B Place the controls within convenient reach of the operator so that he can operate the system without losing eye contact with the roadway Emergency warning devices often require high electrical voltages and or currents Properly protect and use caution around live electrical connections Grounding or shorting of electrical connections can cause high current arcing which can cause personal injury and or severe vehicle damage including fire PROPER INSTALLATION COMBINED WITH OPERATOR TRAINING IN THE PROPER USE OF EMERGENCY WARNING DEVICES IS ESSENTIAL TO INSURE THE SAFETY OF EMERGENCY PERSONNEL AND THE PUBLIC Models NASL847 39 Standard LED X 8 position Amber 47 or 39 NarrowStik NASL847 39XX LED X 6 position Amber in center flashing LEDs on the outside positions NASL547 39 LED X 5 position Amber 47 or 39 Narrowstik LC847 39 Standard LED 8 position Amber 47 or 39 LC Stik LC547 39 LED 5 position Amber 47 or 39 LC Stik NAS3847 39 Standard 3 Up OPTIX 8 position Amber 47 or 39 NarrowStik NAS3847 39XX 6 position 3 Up OPTIX Amber in center flashing LEDs on the outside positions A A DAN 8 NAS3547 39 LED 5 position 3 Up OPTIX Amber 47 or 39 Narrowstik Unpacking amp Pre installation After unpacking the items carefully inspect the unit and its associated parts for any damage that may have been caused in transit Report any damage to the carrier immediat
8. duct for repair or replace ment please contact our factory to obtain a Return Goods Authorization Number RGA number before you ship the product to Code 30 Write the RGA number clearly on the package near the mailing label Be sure you use sufficient packing materials to avoid damage to the product being returned while in transit Code 3 Inc reserves the right to repair or replace at its discretion Code 3 Inc assumes no responsibility or liability for expenses incurred for the removal and or reinstallation of products requiring service and or repair nor for the packaging handling and shipping nor for the handling of products returned to sender after the service has been rendered NEED HELP Call our Technical Assistance Hotline 314 996 2800 IE HACODE 3 Code 3 Inc 10986 N Warson Road St Louis Missouri 63114 2029 USA www code3pse com LP 6000 XL5000 and NarrowStik are trademarks of Code 3 Inc a subsidiary of Public Safety Equipment Inc Revision 11 02 2006 Instruction Book Part No T05765 3M is a registered trademark of 3M Company 2001 6 Code 3 Inc Printed in USA
9. ely Installation 8 Mounting The LC Stik and the NarrowStik was designed with a flexible mounting system to allow its use with as many lightbars as possible The following installation instructions provide direction for mounting the LC Stik and NarrowStik to the Code 32 XL 5000 Series and LP 6000 Series Lightbar frames Information is given however so that mounting on other lightbar systems should be possible Questions about a specific application should be directed to the Technical Hotline number given on the last page of this manual Permanent Mounting Prior to mounting consideration must be given to cable location The cable should exit the endcap on the driver s side unless otherwise specified LP 6000 Series Frame See Figure 2 Figure 3 and Figure 4 below 5 MOUNTING BOLT YO 4 FLAT WASHER q e MOUNTING BOLT MOUNTING BRACKET FIGURE 3 Ma LP 6000 SERIES LP 6000 SERIES EARLY MODEL LATE MODEL MOUNTING BRACKET Ya SPLIT WASHER 14 ACORN NUT XL 5000 Series Frame See Figure 5 below FIGURE 4 ACORN NUT PLASTIC SHIM MOUNTING BRACKET CARRIAGE BOLT FIGURE 5 Wiring Instructions Refer to the manual packaged with the 8 Output LED Narrowstik Controller for detailed control head wiring installation and operation instructions Larger wires and tight connections will provide longer service life for components For high current wires it
10. ers can or will observe or react to an emergency warning signal Never take the right of way for granted It is your responsibility to be sure you can proceed safely before entering an intersection driving against traffic responding at a high rate of speed or walking on or around traffic lanes The effectiveness of this warning device is highly dependent upon correct mounting and wiring Read and follow the manufacturer s instructions before installing or using this device The vehicle operator should insure daily that all features of the device operate correctly In use the vehicle operator should insure the projection ofthe warning signal is not blocked by vehicle components i e open trunks or compartment doors people vehicles or other obstructions This equipment is intended for use by authorized personnel only It is the user s responsibility to understand and obey all laws regarding emergency warning devices The user should check WARNING all applicable city state and federal laws and regulations Public Safety Equipment Inc assumes no liability for any loss resulting from the use of this warning device Proper installation is vital to the performance of this warning device and the safe operation of the emergency vehicle Itis important to recognize that the operator of the emergency vehicle is under psychological and physiological stress caused by the emergency situation The warning device should be installed in such a manner as to A
11. l wire see figure 5 page 5 If any heads do not light replace with a new L E D module or return the entire unit for service If all heads are functioning refer to the control head manual for troubleshooting details related to the control head Refer to the back page of this manual for service information WARRANTY Code 3 Inc L E D emergency devices are tested and found to be operational at the time of manufacture Provided they are installed and operated in accordance with manufacturer s recommendations Code 3 Inc guarantees all parts and components to a period of 5 years unless otherwise expressed from the date of purchase or delivery whichever is later Units demonstrated to be defective within the warranty period will be repaired or replaced atthe factory service center at no cost Use of inappropriate or inadequate wiring or circuit protection causes this warranty to become void Failure or destruction of the product resulting from abuse or unusual use and or accidents is not covered by this warranty Code 3 Inc shall in no way be liable for other damages including consequential indirect or special damages whether loss is due to negligence or breach of warranty CODE 3 INC MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY INCLUDING WITH OUT LIMITATION WARRANTIES OF FITNESS OR MERCHANTABILITY WITH RESPECT TO THIS PRODUCT PRODUCT RETURNS In order to provide you with faster service if you are going to return a pro
12. tting in a brightly lit area Use of the DIM setting may cause emergency lights to not comply with applicable emergency warning light standards Use caution when using the DIM setting to assure that motorists can clearly see the emergency vehicle Specifications NASL 847 8 LC847 LC NASL 847 Size 48 1 2 L 2 7 8 W 2 H Operating Voltage 10 16VDC Current Draw 8 Head NASL 5 Head NASL 8 Head LC 5 Head LC Average 4A 2 5A 1 0A 625A Maximum 8A 5 A 2 0A 1 2A Note Current consumption is reduced by approximately 60 when in DIM mode LC Stik versions do not have a DIM mode Maintenance The NarrowStik and LC Stik require minimal routine maintenance Occasional cleaning of the lens is all that is required to sustain maximum light output Water or Code 30 lens polish and a very soft cloth is needed for cleaning The plastic scratches easily so cleaning is recommended only when necessary The lens should not be removed at any time Parts List Name Type Part Number LED Lightheads Narrowstik Contact Code 3 for Replacements LC Stik Amber TO7090 LC Stik Red Amber TO7549 LC Stik Blue Amber TO7550 Chassis Extrusion 39 TO7964 47 TO7965 Cable 22 Narrowstik TO9695 LC Stik 113195 Endcap TO9502 Troubleshooting Verify that all connections for the Narrowstik LC Stik are correct as detailed in this manual Each head can be checked by placing POWER on the red and red white wires while grounding each individual LED contro
Download Pdf Manuals
Related Search