Smart Kit User's Manual - Bluetooth™ carkits & Cradles
Contents
1. Display Settings Adjusting Display Contrast You can adjust the contrast of the LCD display Settings Display Setting Contrast 20 www tradevision nl 3 Operation Contrast www tradevision nl 21 3 Operation Adjusting Display Brightness You can adjust the backlight level of the LCD display Settings Display Setting Brightness Brightness RR Changing the Backlight Color You can change the color of the backlight to suit your car s interior CK390 has 5 preset colors to choose from Settings Display Setting Screen Color White Available colors Orange Green Blue Red and User Defined You can also self define the backlight color as follows Settings Display Setting Screen Color User Defined R G B it 22 www tradevision nl 3 Operation Enabling Screen Auto Off You can enable or disable the backlight to go dim when the system idle time is longer than 10 seconds Settings Display Setting Screen Auto Off Enable Disable Screen Auto Off Enable Exit Ena ble O Other Settings Enabling and Disabling Automatic Phonebook Synchronization You can setup to automatically upload your phonebook when a connection is established Settings Phonebook Sync Enable Disable Phonebook Sync Exit Finding Out About the Device F2. The control module is designed to attach to the inside of the steering wheel on the left or right side Installing the battery Before attaching the control module install the supplied battery 1 Remove the battery cover from the rear of the control module and remove the old battery if any 2 Insert the new battery with the correct polarity as shown below 3 Put the battery cover back on 6 www tradevision nl 2 Installation Attaching the control module Refer to the following to attach the control module 1 Attach the rubber clasp to the two notches on one side of the bracket base 2 Pull tightly on the rubber clasp and position the bracket base on the inside of the steering wheel 3 Wrap the rubber clasp tightly around the steering wheel and secure it on the other two notches on the bracket base www tradevision nl 7 2 Installation 4 Attach the bracket cover with the two supplied hex bolts 5 Slide the control module into the module bracket as shown To remove the control module push the release button to the right and remove the control module i 6 Now the remote is stabled and attached to the wheel 8 www tradevision nl 2 Installation Installing the Caller ID Display The caller ID is designed to sit on the dashboard once it is attached to the stand Remove the adhesive cover from the sticker
3. O ER 58 MEDIA MENU BUTTONS e O fr 3 ENTER www tradevision nl 25 3 Operation O Factory Settings Reset CK390 allows you to master reset the car kit back to the original factory settings To master reset CK390 please press both Answer and Reject buttons at the same time for few seconds until you hear a series of beeps which indicate that car kit has been reset back to the original factory settings and is also available for making a new pairing Warning If you reset the car kit all phonebook entries and paired settings will be erased Bluetooth Software Upgradeability From time to time new Bluetooth phones are introduced and these phones may not be 100 compatible with CK390 as the software may not recognize new features or functions provided on the new phone CK390 s software must be updated to accommodate new phones CK390 offers an easy way of upgrading software Please contact your authorized dealer for further information regarding software upgrading 26 www tradevision nl
4. Phonebook Phonebook Functions 2 Search for a Name to Call 16 Accessing Received Dialed and Missed Calls 17 Dialing EAN 0100 6 gt eee 17 Initiating Private Calls 17 Connection Settings 18 Pairing Setup T AA A a 18 Disconnecting From the Current Phone lt cooocccconococnnnaronnnananons 18 Viewing Connecting and Deleting Previously Paired Phones 18 6 Language Settings A eer ree er ere rer ere 19 Language Settings ii bi 19 www tradevision nl O Sound Settings aeriene eirinn eena Adjusting the Speaker Volume Disabling and Enabling the Keytone lt lt lt lt rmmoocccorinacinaninaninaninnnos 20 Display Settings e ooemasion insscnaatanoco mate cipreses Adjusting Display Contrast Adjusting Display Brightness lt e oooonnnicnnccnncanancccana nono 22 Changing the Backlight COlOr lt lt lt lt lt eoooomomrocniaanccninccanancannos 22 Enabling Screen Auto Off Other Settings A Enabling and Disabling Automatic Phonebook Synchronization 23 Finding Out About the Device O FM Transmission amp A2DP for Stereo MP3 Playback Setting up FM Transmission lt lt lt ccocoreccnnncnononenonnaronnnnanennnarenon Using A2DP Media Player lt lt ooooooomccccccnncnncnnananoncnnnnnnannnnnnnnos O Factory Settings Reset eee a Bluetooth Software Upgradeability oveeveneeenenees 26 www tradevision nl 1 Introduction Carefully unpack
5. sorting function in the background If you access the phonebook before the sorting is completed you may see that some contacts are not displayed in right order however first character will always be in order This is normal and CK390 will continue to sort the contacts until it is finished However if your phone does not support automatic phonebook synchronization which also means you cannot use the upload phonebook function you will need to upload the required entries by sending them manually from the mobile phone via Bluetooth This is the object push profile OPP method To use the OPP method for uploading contacts please use the following steps Phonebook Receive Contact Name amp Numbers Upload Phonebook Receive Contact Back As soon as you select Receive Contact the CK390 temporarily disconnects from your mobile phone to allow the contact entries to be included Select the entry required and go to the send option to select send via Bluetooth You can send multiple entries by repeating the process Once you have finished push the Reject End button to stop the www tradevision nl 15 3 Operation receiving contacts process and re establish the Bluetooth link with the last connected mobile phone Note Some phones support sending multiple contacts at one time using the OPP method It is recommended that no more than one hundred selections be sent at a time Phonebook Functions 2 Search fo
6. TRADEVISION AUTOMOTIVE SUPPLIERS tl A aig ao Bluetooth Handsfree Car Kit with LCD USER S MANUAL Model CK390 www tradevision nl Contents 1 Introduction iaa is eiii iia aii 1 O Identifying COMponents i rttrrrrerrtccnnnonnnennnrcnnrannnrnnnanenos 1 Core Components 1 Optional Components PPEP EE PPE O E T 2 Optional ACCESSOriesS lt oooocccconccnnnonoconnnanononenonnnrnnnonerennnarennns 2 2 Installation ccc rt ne rr 3 O Installing the Junction BOX terrtrrrtrererenonrcnnrnenarenonenos 3 8 Connecting the Power Supply rttrrtterrrtccnrcnnarenanenenenno 4 Connecting Accessories erteterrrrrecccnrrnenonerecnnnrrecanrrreenos 5 O Preparing the Control Module pa 6 Installing the battery 6 Attaching the control module 7 Installing the Caller ID Display OS 9 O Installing the Microphone rrtterrtrcctrenornnonnconanenarenenennos 10 Installing the Microphone AR AA 10 AN O How to Operate the Car Kit crrrrrcccrorrenenorrnncconrrnenonaresnos Understanding the icons on your screen 8 Basic Operation rterrrrrrecorrrrecnnneneconermenonrrtecrrrrterrrrrtenos Connecting to the Mobile Phone for the First Time Dialing the First Call errrcrrrrorrrccnnnonanenonrconrnonarennanenos Receiving and Ending a Phone Call oooooorooorcocronaronaronarononos Adjusting the Conversation Volume Phonebook Functions 1 Updating
7. e CK390 if your mobile phone supports automatic www tradevision nl 13 3 Operation phonebook synchronization for example Nokia 6230i it will upload call history phone book entries and also sort the phone book as soon as the phone is connected with the car kit Note Phonebook synchronization and sorting time may differ depending on size of phonebook list This may affect the initial remote control response at start up In the event that you do not wish to upload automatically you can disable this function and upload the phonebook manually To setup manual phonebook upload please follow the steps below Settings Phonebook Sync Enable Disable See Other Settings on page 22 for more information Note Phonebook Sync default setting is enabled To upload the contacts manually from both phone memory and the SIM card please follow the steps below Phonebook Upload Phonebook Please note that automatic phonebook synchronization will add in new contacts which you have entered into your mobile phone but it will not delete the entries which have been removed from your phone To update your deletions or additions please use the Upload Phonebook function 14 www tradevision nl 3 Operation Name amp Numbers Upload Phonebook Receive Contact Back Note Contacts are picked up in random order by the car kit therefore after all entries have been uploaded CK390 will perform the
8. ill allow CK390 s device name to reside in the mobile phone memory listed along with other previously paired devices in the handset You then need to press the connect command on the phone to establish the connection with CK390 and your mobile phone name should appear on the main idle screen You will also get battery and signal indications if your phone supports these functions Note Please contact your dealer for a compatibility list Nokia 6230i Connected 12 www tradevision nl 3 Operation Dialing the First Call Scroll up and down until the cursor is on Dial Number then press the Enter button Scroll up and down to select your desired number press Enter to select the number Phonebook 4 Call History 12345678 Dial Numbe 0286655757 Settings Once you have finished selecting the telephone number press the Answer button to call the number you have just entered Receiving and Ending a Phone Call When there is an incoming call press the Answer button to accept the phone call To end a call press the Reject End button to terminate the conversation Adjusting the Conversation Volume User can adjust the volume during the conversation by pressing the up and down scroll button on the remote O Advanced Operation Phonebook Functions 1 Updating Phonebook Call History Dial Number Settings There are a number of ways to upload your phonebook to th
9. nction box 2 Use two screws not included to fasten the junction box in place af www tradevision nl 3 2 Installation 8 Connecting the Power Supply For Options 1 and 2 only The following illustration demonstrates how to connect the Car Kit s power cables to the vehicle s electrical system Yellow cable To car radio mute NPN gt Red cable To Battery 12 24V Blue cable To ignition Black cable GND Power cable Important The blue cable must be connected to the 12 24V switched to enable the Car Kit to go into standby A mode Do not connect the blue cable to the 12 24V permanent Doing so may discharge the battery of the vehicle and prevent the Car Kit from being reset 4 www tradevision nl 2 Installation Connecting Accessories The following illustration shows where to connect accessory devices Junction Box Speaker Microphone Caller ID Item Description The caller ID should be placed on the dash within view of the driver and passenger ee See Installing the Caller ID Display on page 9 Microphone Ideally the microphone should be located in front of the user and above waist height For best reception the speaker should be Speaker mounted at least 80cm 30 inches from the Car Kit s microphone www tradevision nl 5 2 Installation O Preparing the Control Module
10. nected i Phone Phone Reception Battery pi D pa FW rash Strength Level x Call History loading A2DP al number increases enable when when loading on songs are playing more contacts from mobile FM ae ee Enabled Phonebook loading Handsfree via FM number increases This icon shows when when loading on more sound output is contacts from mobile transferring through FM CK390 remote control and optional 2538 remote control Scroll Down Scroll up Volume Down Volume Up Reject End Button A Answer Dial Button e CK390 LED Indicater ENTER Button www tradevision nl 11 3 Operation O Basic operation Connecting to the Mobile Phone for the First Time As soon as the ignition is turned on CK390 text will be displayed on the backlit screen and it will quickly enter the Pairing mode searching for available Bluetooth mobile phones for pairing up If the pairing screen does not display automatically you will need to turn on this function manually See Connection Settings on page 18 Pairing CK390 You will need to switch on the mobile phone s Bluetooth connection and conduct a search for new Bluetooth audio device At the end of the search you should be able to see CK390 s name appearing on the mobile phone screen Please select this item to pair and enter 1234 when prompted by the password request This w
11. ngs Initiating Private Calls A privacy function is available in the CK390 car kit The handsfree feature is disabled when the privacy function is enabled allowing for the use of the handset during the conversation To initiate the private call function simultaneously press both scroll buttons on the remote control during a call Once www tradevision nl 17 3 Operation activated press the Answer button once to return to handsfree Connection Settings Pairing Setup The majority of the phones can connect with CK390 under the hands free profile as follows Settings Bluetooth Setup Pairing a Device Pairing Phone It is possible that some phones do not support the hands free profile but instead offer a headset profile In this case you will need to setup the headset pairing to connect the mobile phone with CK390 as follows Settings Bluetooth Setup Pairing a Device Pairing Headset Disconnecting From the Current Phone You can disconnect the phone from the CK390 s menu NOKIA N95 Settings Bluetooth Setup Active Device Disconn Des Orit Exit Viewing Connecting and Deleting Previously Paired Phones You can re establish a connection with a previously paired phone by entering the paired phone lists Settings Bluetooth Setup Paired Devices 18 www tradevision nl 3 Operation Note To re establish a connection with a p
12. or information about the device go to Settings About Device www tradevision nl 23 3 Operation CK390 lt Device Name SW V 2 5AF lt __ Software Version BT 200B009 lt Y __ Bluetooth Version O FM Transmission 8 A2DP for Stereo MP3 Playback The Car Kit offers another source for sound output FM transmission FM method not only allows hands free sound but also stereo MP3 music played from the mobile phone Setting up FM Transmission To setup FM frequency please use the following steps Settings Sound Settings FM Settings gt 88 8MHz Other Frequencies 100 1MHz 106 2 MHz FM User and FM Disable To setup a User Defined frequency Settings Sound Settings FM Settings FM User To disable FM transmitter Settings Sound Settings FM Settings gt FM Disable FM User2 FM Disable 24 www tradevision nl 3 Operation To enable or disable hands free output via FM transmitter Settings Sound Settings Volume Output FM gt Enable Disable HF OUTPUT FM Exit Using A2DP Media Player To enter Media Player interface Settings Sound Settings Media Player Alternatively press the up scroll button to gain access to the media player instantly Use the Media Menu buttons to Play Pause jump to Previous or Next songs and Stop playing PLAY PAUSE STOP Kay gt ff ol ta
13. pad attached from the base and press firmly to secure in place If you wish to attach the LCD display elsewhere such as next to the car radio detach the base from the stand by removing the screw as demonstrated Turn the stand inwards and apply a sticker pad provided to the back of the stand Position the stand and press firmly to secure in place www tradevision nl 9 2 Installation Installing the Microphone Before installing the microphone take note of the following Make sure that the cable can reach from the microphone to the speaker If the cable is too short relocate the microphone Do not lengthen the cable The supplied microphone is uni directional For best results place the microphone in front of the person talking It has a reception angle of 60 degrees and is most effective within a 60 cm radius Installing the Microphone Find a suitable place for the microphone Remove dust and grease from the surface 1 Remove the protective iin fms cover from the Velcro and D O press it firmly onto the bottom of the microphone 2 Remove the protective cover from the other Velcro pad and firmly press the pad in place 3 Attach the microphone 10 www tradevision nl 3 Operation O How to Operate the Car Kit Understanding the icons on your screen Please see below for the explanations of the icons on the main screen i 6233 Y Con
14. r a Name to Call After the phonebook is uploaded it will reside in the car kit s memory You can search these entries to call by going through the A Z index and selecting the first character of the name to look up a particular entry For instance choose W for William in the Name amp Numbers menu and it will list the names starting with W To choose a desired phonebook scroll up and down the alphabetical list and select a letter entry Phonebook gt Name amp Numbers ABCDEFGHIJKLMNOP 0286655757 ABCDEFG HI aie Andy Select the desired contact and press the Answer Call button to dial out Alternatively press the Enter button in the idle screen to instantly access the phonebook s A Z index 16 www tradevision nl 3 Operation Accessing Received Dialed and Missed Calls CK390 can sync with your mobile phone s call history To access the previously dialed calls please go through the following steps Call History Calls Dialed To access received calls Call History Calls Received To access the missed calls Call History Calls Missed Dialing a Number To dial a desired number please go to Dial Number and scroll up and down to the number you wish to call press Enter to select the number Once you have selected the telephone number press the Answer button to call the telephone number you have just entered Phonebook 4 Call History TSE OTe Dial Numbe 0286655757 Setti
15. reviously paired device the current pairing must be disabled first To re establish a link please go to the desired device name and press connecting to re connect with the CK390 Settings Bluetooth Setup Paired Devices select a device to connect such as Sony Ericsson K800i Conn Nokia N95 Sony Eric sson K800i Nokia N80 Sony Ericsson K800i Del Exit To delete a pairing simply select the desired device name and scroll to Del and press Enter to confirm the deletion Settings Bluetooth Setup Paired Devices select a device to connect such as Sony Ericsson K800i Del O Language Settings Language Settings Depending on your region there are up to 10 languages built into the CK390 and the default language is English To change to a different language simply follow the following steps Settings Language Setup English www tradevision nl 19 3 Operation Available languages English Spanish Portuguese French Italian German Dutch Norwegian Danish Swedish Sound Settings Adjusting the Speaker Volume You can adjust the speaker volume to suit your required sound level Settings Sound Setting Volume Settings gt Volume DE R Disabling and Enabling the Keytone You can disable or enable the CK390 s keytone Keytone Settings Settings Sound Setting Exit Keytone Settings Enable Disable
16. the CK390 Bluetooth Handsfree Car Kit and check that the following items are included O Identifying Components Unpack the Car Kit package and ensure the following items are included Core Components sa E Control module CK390 LCD R one 23A battery Caller ID Junction Box Rubber Clasp Control bracket Microphone hex bolt x 2 and key x 1 Note If any item is missing or damaged please contact your dealer www tradevision nl 1 1 Introduction Optional Components S Option 1 Option 2 Optional Accessories Suction Cup LCD attachment suction cup Note Please contact your dealer for availability 2 www tradevision nl 2 Installation This section demonstrates how to set up and install the CK390 into a vehicle O Installing the Junction Box The Car Kit is designed to work with the 12 24 volt power supply of the vehicle Refer to the following to install the junction box in a vehicle 1 Locate a suitable place inside the car to mount the junction box Select a dry place that avoids excessive heat and mechanical vibration Ideally the junction box should be hidden from view but still easily accessible Note Make sure that the cables are long enough to support the location of the junction box If the cables are not long enough do not lengthen the cables Instead relocate the ju
Download Pdf Manuals
Related Search