ITA3D 600 RGB ILDA laser with 3D effect User manual - Bax
Contents
1. ITA3D 600 RGB ILDA laser with 3D effect nome AA SECIS SIRES ERAT ITASD 600 lt User manual Safety precautions WARNING This unit may cause serious injury to eyesight when used incorrect It therefore is strongly advised to read this user manual carefully to get familiar with the functions of this laser device WARNING This unit must be operated by or under the supervision of an adult This device is not suitable for children WARNING Do not look directly into the beam coming out of the lens from short distance or when a solid beam is projected This may cause serious injury to eyesight Ayra is not responsible for any injuries caused by incorrect use of this device WARNING Do not project the beam of this unit on to reflective surfaces as the shattering beam may cause injury to eyesight Installation requirements Always check the voltage settings on the unit and the power supply you want to connect the device to If the voltage requirements do not meet do not connect the device as this may cause serious damage This device must be installed by a professional technician in a standing or hanging position Always pay attention to the positioning of the unit as the beams may project directly into your audience It is strongly advised to NOT project the beams directly into your audience Ayra strongly recommends a minimum distance of 1 5 meters in height between the lowest projected laser beam and your audie2. 255 is optimal brightness 13 Drawing 0 127 Auto drawing mode 1 128 255 Auto drawing mode 2 NOTE While using ILDA it is still possible to use DMX channel 2 to control the effect wheel It is also possible to use the dipswitches on the rear of the unit Technical specifications TYPE ITA3D 600 Laser diodes Type ITA8D 600 100mW red laser wavelength 635nm 100mW green laser wavelength 532nm 400mW blue laser wavelength 450nm mixed output 500mW white max Tech specs scanset 25 kpps high speed optical scanner with a maximum angle of 30 degrees working modes auto sound active master slave DMX 512 ILDA graphics and effects 128 beam show and animated graphic show patterns with 3D animation high efficiency 3D optical grating system for unique 3D lighting effects hanging bracket for use with a lighting stand or truss system built in microphone with adjustable sensitivity pattern size adjustable small large ILDA controlwith DB25 connectors DMX control with 3 pin XLR connectors DMX control 12 channels Power supply 100 250V AC 50 60 Hz Power consumption 50 Watt dimensions 200 x 235 x 130 mm weight 4 5 kg Laser class and licensing This laser has the capability to perform with a power of maximum 500mW theoretically However the optics of the laser have a small influence on the beam output power thus reducing the maximum power slightly In practice
3. project a static small beam with high intensity when using ILDA software Therefore only skilled technicians and or laser operators should work with this kind of laser to prevent these situations The maximum scanner speed is 25 kpps but a setting of 20 kpps max in your laser software is recommended Seiting a too large scanner speed in your laser software may cause permanent damage When creating figures patterns or graphics always check the realtime projection of your laser to check if the laser scan set is capable of projecting the figures Slight flickering while projecting complex or very large patterns is virtually unharmful for the scan set when setting the correct scan speed but large amounts of flickering and unrecognizable patterns are a sign that the scan set is unable to perform the task and drives its capabilities to the maximum with possible permanent damage as a consequence Warranty is void when the scan set of the laser is damaged caused by improper use DMX operating mode While in the DMX mode it is possible to select the working mode of the laser That way you can either choose to use your own programmed presets of your DMX controller or to activate the music activated automatic working mode of the laser to have a fully automatic lasershow Depending on the starting address you selected earlier the laser responds to the following commands In this example we use DMX starting address 1 When you use a different DMX star
4. this device falls under Class 3B Class 3B and Class 4 lasers are able to cause serious injury to your audience when used incorrectly It is therefore strongly recommended that only skilled laser operators and technicians install and operate this device Class 3B and Class 4 lasers can be used for audience scanning in a safe way but only when used by a skilled laser operator or technician There are no official laser laws or licenses to operate or own a laser device However there is specific guidance issued by the Health and Safety Executive in the form of a document called HS G 95 The Radiation Safety of Lasers Used for Display Purposes HS G 95 outlines a number of detailed points to consider when using lasers for lightshow purposes Class 3B and 4 laser products are required to have several specific safety features as part of their design These features are laid out in the British Standard on Laser Product Safety BS EN 60825 1 and are a requirement of the product meeting CE approvals 10
5. X not used or not active for this mode DIPSWITCH CHART ajajajaja TON o o o x x x x x x 0 fonoa 1 o0 o x x x x x x o AUTO MopE 0 o 1 x x x x x x 0 SLAVE MODE SET DMX ADDRESS 0 Muilticolor effects 1 Single color whilte effects 8 EFFECT MODE 0 MULTI EFFECT 0 NORMAL ANIMATION EFFECT 0 0 0 O MULTI PATTERN EFFECT 1 X 7 3D DOT EFFECT 1 3D PLANE EFFECT p4 gt Working mode explanation Sound active The unit uses its internal microphone to sense music the beat of the music and will change patterns according to the beat of the music The microphone is situated at the front of the laser device On the rear of the laser there is an adjustable microphone sensitivity knob Please note that the sound activated mode will not function properly when the music source is not loud enough or when only high pitched sounds are played Auto beam The laser device will activate a pre defined lasershow on a solid speed setting The patterns are mainly beam effects Auto animation The laser device will activate a pre defined lasershow on a solid speed setting The patterns are mainly animations and graphics Slave mode It is possible to link several ITA3D 600 fixtures for a synchronized lasershow without the use of a DMX controller Connect your devices with standard XLR XLR cables The first device in the chain needs to be set toa basic function such as sound a
6. ctive or one of the auto shows Select the slave mode on all other connected device in the chain You will notice that these devices will mimic the actions of the first device DMX mode With an external DMX controller or DMX software it is possible to control every feature of the laser device It is possible to adjust the built in patterns and to add several effects such as zoom effects or pattern rotation NOTE When the DMX signal or master slave signal is lost due to a failure in the DMX connection or any other reason the laser will shut off the output due to safety issues This prevents the projection of static images and or patterns ILDA mode When you wish to control this laser using ILDA lasersoftware you need to connect a DB25 cable to the laser The laser automatically detects the ILDA connection and will override any selected working mode thus switching automatically to ILDA mode When an ILDA signal is detected but there is no data transfer the laser will shut off automatically to prevent the projection of static beams Also when the connection during a lasershow is lost the laser will shut off the beam output to prevent injury WARNING When using this laser device Ayra strongly recommends not using the laser for audience scanning purposes Only a skilled technician and or laser operator should operate this laser while audience scanning is performed for safety reasons Audience scanning should always be performe
7. d with a moving graphic such as a tunnel or wave and with large graphics to prevent that high intensity beams are projected into the eyes of your audience long enough to cause serious injury Because the automatic modes of this laser use different types of graphics the laser should not be used for audience scanning purposes when operating in these modes Only when using DMX or ILDA it is safe to project laser patterns into your audience but only When the graphics are large so the beam intensity is relatively unharmful When the graphics are moving such as rotating movement so the graphic can never project continuously on the same spot When you_have_a laser emergency power cut off installed use the interlock feature ora 230V power switch When a skilled technician or laser operator is controlling the laser When the audience scanning begins at a distance of at least 10 meters of the beam output If one or more of the above stated situations or features is not applied the laser device should not be used for audience scanning purposes and the projection of the laser should never touch your audience A minimum projection height of 1 5m above your audience should prevent this Ayra can not be held responsible for any damage or injuries caused by incorrect use of this laser device Audience scanning is a term which describes the effect of laser beams being projected into your audience Theoretically it is possible to
8. for a longer period of time disconnect it from the power supply and store it in a dust free environment Always check the unit for possible damage before use If you suspect that something is wrong with the unit do not connect it to a power source When you suspect that your unit is broken or damaged contact your local dealer or a certified technician to inspect the unit When your device does not generate any laser beams do not look directly into the lens When the laser suddenly produces a beam it may cause severe eye damage possibly resulting in permanent visual loss Device overview REMOTE CAUTION A HIGH VOLTAGE INSIDE DISCONNECT INPUT POWER BEFORE INTERLOCK ON OUTPUT Beam output A gt INTERFACE 1 2 Power status LED indicator red e 3 Microphone sensitivity LED indicator blue 4 Built in microphone used for sound active mode 5 DMX input 6 DMX output 7 ILDA DB25 input 8 ILDA DB25 output 9 Pattern size small large 10 DMX dipswitch setting also used for activation of auto sound active mode 11 Microphone sensitivity knob low high 12 Remote interlock connector 13 IEC power inlet 14 ON OFF switch 15 Key lock switch Setting up the device Setting up the device When the power supply is connected the unit will first calibrate the stepping motors of the unit It is normal that this may cause any noise When the calibration is done the unit is ready to be used in t
9. he selected DMX automatic or music controlled mode It is possible that the unit may shut off the beam projection when no music or sound is detected This will avoid the projection of a solid static beam which may cause injury to eyesight This unit uses an advanced scanset to create variable movements to the laser beam This way figures and patterns can be made The unit uses a high speed 25 kpps scanset to create the moving beams of the laser It is normal that the laser beam and projection may appear flickering when projecting very large or very complex patterns The projected beams of the unit may appear shivering when projecting very complex or very large patterns on surfaces as a wall ceiling or decorative cloth Selecting a working mode This laser device has several working modes which are automatic music controlled ILDA and DMX To select the right operating mode for your situation use the dipswitch panel on the rear of the unit A DMxX dipswitch panel works with a binary character It sends a 0 or 1 message to the electrical circuit To select a working mode pay close attention to the information scheduled below Every DMX dipswitch stands for a certain value which is on or off The values are stated as below 1 1 2 2 3 4 4 8 5 16 6 32 7 64 8 128 9 256 10 mode switch DMX ON OFF To select the different working modes pay close attention to the setting of DMX dipswitches below NOTE value
10. nce for optimal safety If there is no other option keep a minimum distance of 5 meters from the beam exit to the first beam that hits your audience When installed in a standing position a safety cable is recommended to secure the unit When installed in a hanging position this unit MUST be secured by using a safety cable capable of holding 10x the weight of this device When installed in a hanging position this unit must be mounted to a proper surface e g a truss system When using a truss system Ayra recommends the use of a proper hook or halfcoupler Make sure there are no flammable objects in the direct environment of the device Such as decorative objects Keep a minimum distance of 1 5 meter Do not block the beam exit and fan Keep a minimum distance of 0 5 meter from any walls to provide sufficient cooling Make sure the beam exit and fan are not blocked by any objects in the near environment This unit must be connected to a grounded power supply that meets the voltage requirements of the device Maintenance and protection Keep the unit away from dusty environments as this may have negative effect on the fan cooling system and laser optics Ayra recommends using a flightcase for storage of this device Clean the optics and fan of the laser with a small soft brush and vacuum cleaner when needed Clean the housing of the unit with a damp cloth WARNING Always disconnect the unit from the power supply when clea
11. ning the unit Reconnect the unit only if any moist on the fixture disappeared completely This laser device is a lighting effect designed to support visual entertainment while playing music Continuous use is not recommended Do not use the device longer than 3 hours subsequently so the unit can cool down This will provide a longer lifespan for the diodes Apply a cooling down time of 25 minutes before re activating the laser Do not switch the power on and off too often as this may cause serious damage to the unit Avoid heavy shocks and collision during transport and use as this might cause damage to the laser diodes electronic circuit optics and housing Keep the device away from moisture rain water or any liquids as this may cause a short circuit and or electric shocks If any liquid enters the unit power supply or housing of the unit disconnect the unit immediately and do not reconnect the power supply Contact your local dealer or technician to inspect the unit for any damage Box contents Box contents 1x ITA3D 600 laser device 1x user manual 1x IEC to Schuko power cable 1x XLR XLR DMX signal cable Unit and accessory inspection Always use the supplied power cable to connect the unit to a power supply If the cable appears broken or has visible damage do not use it The supplied cable can be replaced with a regular IEC to Schuko cable with a minimum cable diameter of 0 75m2 If the unit will not be used
12. ting value for example 29 the unit will respond from channel 29 30 31 and so on For more information about DMX consult the manual of your DMX controller or software Channel Function Value Description 1 Mode 0 63 Sound active mode disabling channel 2 64 127 Automatic mode disabling channel 2 128 191 Manual mode auto run function 192 255 Manual mode sound active mode 2 Effect mode 0 49 Multi effect 50 99 Normal animation effect 100 149 Multi pattern effect 150 199 3D dot effect 200 255 3D plane effect 3 Color 0 255 Closed White Red Yellow Green Blue Purple Fixed color Random single color Random 7 colors Moving 7 colors fixed color 4 Pattern 0 255 128 built in patterns selection 5 Movement Y 0 127 Manual Y positioning 128 191 Automatic down movement 192 255 Automatic up movement 6 Movement X 0 127 Manual X positioning 128 191 Automatic right movement 192 255 Automatic left movement 7 Rolling X 0 127 Manual positioning 128 255 Auto rolling 8 Rolling Y 0 127 Manual positioning 128 255 Auto rolling 9 Rotation 0 127 Manual positioning 128 191 Automatic clockwise rotation 192 255 Automatic counter clockwise rotation 10 Zoom 0 85 Auto zoom 86 170 Auto zoom 171 255 Manual zoom 11 Pattern size 0 255 0 is moderate 1 255 is small large 12 Display dot 0 255 0 is display dot
Download Pdf Manuals
Related Search