User Manual CO2 Euthanasia Electronic station
Contents
1. Nitrogen protoxyde and halogen agents Don t use when using chloroform or trichloroethylene Don t have any contact skin or eyes with the product or its packing In case of contact with skin or eyes immediatly rinse with clear water and contact a doctor The use of this soda lime must be supervised by authorized person The dust of soda lime is caustic and can burn the respiratory organs in case of inhalation Use gloves and protection glasses during filling and emptying of soda lime Don t use the end of the soda lime packing because much more dust at the bottom of the bottle Instructions of use Please read it carefully before use Soda lime replacement frequency CO2 absorption by soda lime occurs a progressive color change of the raw material Depending of brand of products soda lime generally move from white to purple or from pink to white Note Used soda lime should be immediatly removed Otherwise after several hours it will take back its original color and give an wrong information about its status Destruction Do not incinerate soda lime because it contains inflammable raw materials like cyclopropane ethylene or ether Even if used soda lime can keep some alcaline characteristics it can be treated as every organic waste Storage lt must be stored in its intact packing in clean and dry environment at a temperature of 0 32 C Avoid direct sunshine Protect it from choc and water stored as described it2. on When logo appears press on the screen Etalonnage 1 5 appears press several times until the word Haut gauche appears Then press on the top left part of the screen Then Top right then bottom left and bottom right Touchscreen is defective Call supplier Soda lime is too wet change soda lime sensor is defective Call supplier the flow of gas is not Check gas inlet is open bottle is not available empty Time and or flow Increase the flow if possible with parameters are not good your network or increase time of session 11 Terms of Warranty Warranty field This manufacturer warranty covers only TEG device from TEM SEGA It doesn t include all parts used as interface or connection if not provided by TEM SEGA This warranty doesn t apply if the damages result from bad use accident negligence from any modification servicing or repair not made by TEM SEGA technicians Warranty covering TEM SEGA warranties that this device is complying to its specifications and that every issue due to manufacturing conception or defective parts will be repaired or replaced at manufacturer choice by himself free of charge for the client for a two years period after the delivery date This warranty will stop immediately after this period without any advertisement for the manufacturer This warranty is back to manufacturing that means the shipping cost back to manufacturer are under client responsibility The manufacturer wi
3. can keep generally during two years Expiration date is mentioned on the packing Technical data Active componants Soda lime Hydroxyde de calcium size of granula 2 5 5 0 mm Hydroxyde de sodium humidity 12 19 Water OH during use 10 pH before use 12 14 9 Technical Specifications SIZE 140 mm x 360 mm x 250 mm WEIGHT 3 Kg 2 electronic flowmeters Air and CO2 from 20 to 200 FLOWMETERS L min Servicing pressure from 3 to 4 bars recommended 3 5 bars power supply 24 VDC PRESSURE SENSOR From 0 to 30 cm H2O GENERAL POWER SUPPLY 230V 50Hz POWER CONSUMPTION max under 24V 50W USE TEMPERATURE From 20 to 24 C optimal 22 C 10 Servicing and Repair The device should be checked every year by qualified people Servicing report must be keep during several years Each year change all the tubes control and change if necessary the air tight join Nothing happen no power supply check power supply when switching ON check GFCI GFCI is down Call supplier electronic board is defective When switching ON green light is OK but nothing appears on screen or defective light on the screen Touchscreen is not answering Pressure alert turns red during session Flow alert turns Red during session Animaux still sleeping or awaking at the end of session electronic board Is call supplier defective touchscreen is Touch screen calibration decalibrated Switch off the device then switch
4. TEM S EGA TEM SEGA 27 All e Charles 33600 PESSAC Tel 05 56 32 29 63 laruin User Manual CO2 Euthanasia Electronic station Ref TEG 23 07 2013 Manuel TEG 1 16 General Information Labelling CE on SN om de 230 fil Hz REF Minitag Vi MODELE Mimifug 20 re e r s 300 Read carefully documentation before use Electrical hazard always disconnect power supply before opening parts where this mark is applied Xi Irritant Chimical hazard always take appropriated precautions before opening parts where this mark is applied Suffocation hazard always pay attention to the right ventilation of room and safety procedures when this mark is applied Disposal of waste All consumable must follow hospital waste treatment procedure soda lime Consumable References 2175 1 General Use This station is dedicated to labs staff to perform CO2 euthanasia for rodents during authorized experimentation programs lt has been designed to work only in labs and be used by trained people complying with ethical consideration and regulations ATTENTION all use except veterinarian purpose is strictly forbidden 2 Operation Principle This station is able to drive a CO2 process induction with following steps 1 Rodent induction 2 Rodent euthanasia by CO2 saturation 3 Purge Many protocols are memorized More protocols can be added by the authorized user if nece
5. ep 10 03 2011 15 40 29 Vidange Temps 43s Debit 0 Vmn Pression 0 cmH2O Ne Pas Ouvrir TT i t a lt Q a 8 P SS 5 Please wait the end of the step before trying to open the chamber Fixed stops ATTENTION the cover is very heavy to tight the chamber An hydraulic cylinder is presnet to assist you during the opening DON T DROP THE COVER DURING OPENING AND PAY ATTENTION NOT TO DROP AGAINST THE FIXED STOP 6 To start a new session Remove the animals box Introduce a new box of animals Close the cover and lock it check the soda lime color following next chapter procedure then press on start button DnD 7 If you dont have other animals a Switch OFF the device b clean the induction chamber c check soda lime following next chapter procedure 8 Replace used soda lime Unlock the rack and open it smootly Under the rack you have a water collector Please check it carefully and clean it if necessary 7 Cleaning and disinfection In order to preserve your equipment it is necessary to clean and disinfect it regularly Clean and disinfect the stainless chamber as often as needed and at least every day Avoid alcohol on plastic parts 8 RECOMMENDATIONS FOR CO2 SODA LIME USE Soda lime type Medisorb or other Indications Carbon dioxyde absorber for CO2 Precautions and attention The CO2 soda lime absorbant is only used with Air oxygen heliox
6. f the parameters By pressing on Animal button you can access the configuration menu for each step of the protocol You can change the time and flow for each step of the protocol 14 02 2012 14 55 29 Each protocol is composed of 5 steps 1 induction step 2 Hold on step Air CO2 Euthanasia step Hold on step CO2 Purge step O1 A By pressing one of the step you will access to the configuration parameters menu Then you can tune time parameter and flow parameter Temps 1 mn Debit 3C To memorize your tuning press on Valide button To cancel press on Esc button When all the steps are programmed then press on Return button You reach the initial menu 6 4 Configuration of the device In this menu you can set the Air CO2 proportion during induction step time and date of the device name of the device and the pressure alert level by pressong the appropriate button you can reach each following menu CO2 proportion setting Date heure setting Name of the device setting 6 5 Euthanasia session release From the main menu you can release the euthanasia session by pressing the Valid button Then you reach the release screen Before pressing on Depart button please check all connections are ready 6 6 Euthanasia session operations STEP BY STEP PROCEDURE 1 Introduce the animals into the induction chamber They must be placed into their living box after Removing the top of the
7. gs and operations are represented by buttons They can be activated by single finger touch or non sharp stylet 6 Operations 6 1 Getting started General switch ON is starting the device In case of emergency the same general switch will immediately stop the power supply ATTENTION never switch OFF the device during an euthanasia session or purge session When switching on the following screen appears 4 tem sega Euthanasie Version 4 5 It provides the software embedded version 6 2 Program Selection and tuning When station is ready to work you have the following screen 14 02 2012 14 55 29 In this menu you can choose one of the memorized protocols or you can define your own protocol When you select one protocol you have the following menu 14 02 2012 14 56 21 Config Nom Type 1 Boite Souris 35L 100 induction Temps 3 Debit 35 I mn Maintien Air CO2 Temps 0 mn Euthanasie Temps 3 mn Debit 30 mn Maintien CO2 Temps 1 mn Vidange Temps 6 mn Valide This screen shows the last settled parameters 1 CO2 proportion during induction step 2 Time and flow for each step of the protocol Please check if the settings are fitting and then you can release the session Otherwise please follow the next chapter 6 3 Protocol definition or change In the previous screen press on Config button Step 1 select box volume This step is not necessary for the TEG station Step 2 setting o
8. living box Close the cover and lock it ATTENTION the cover is very eae to tight the chamber DON T DROP IT when eae 3 Press the Depart button to launch the session lf the Depart button stay red light that means the Lock is not closed 4 Then you will access to the operations menu This menu shows the step in progress the remaining time for this step the real time flow and internal pressure DO NOT TRY TO OPEN THE CHAMBER DURING THIS STEP In case of emergency please use the STOP button then you reach the following menu lf you press on Valid button you will immediately move to the purge step At the end of induction step you will move if programmed to Hold on AIR CO2 step 10 03 2011 153849 Stop Maintien Air CO2 Temps 159 s Debit 0 Vmn Pression 0 cmH20 Ne Pas Ouvri DO NOT TRY TO OPEN THE CHAMBER DURING THIS STEP In case of emergency please use the STOP button following the same process that previously At the end of this step you will move to Euthanasia step DO NOT TRY TO OPEN THE CHAMBER DURING THIS STEP In case of emergency please use the STOP button following the same process that previously At the end of euthanasia step you will move if programmed to Hold on CO2 step DO NOT TRY TO OPEN THE CHAMBER DURING THIS STEP In case of emergency please use the STOP button following the same process that previously At the end of this end you will move to purge st
9. ll take in charge the re shipping to client after repair ALWAYS READ THIS USER MANUAL WITH ATTENTION BEFORE USE This could prevent from wrong manipulation that could cause damage to the device These damages will not be covered by the manufacturer warrant
10. ssary 3 Regulations compliance of the device EN 61010 for electric safety of labs device EN 61326 1 class B for emission of EMC EN 61558 2 for TBTS power supply ROHS for electronic parts Stainless steel classification and regulation of use NF C15 100 electrical conformity European Directive 98 24 CE protection of people against chemical risks ISO 14644 1 for clean and controlled environments 4 Connection and settings Front side General switch ON OFF Touch screen Electronic lock Soda lime rack Rear Side CO2 input Precautions before use Check the device is connected to 220V power supply with ground connection Check the CO2 input is connected to a network or a CO2 bottle Check this gas is delivered at 3 bars service pressure Check no tube is damaged or pinched Check that soda lime rack is full following chapter 8 recommendations ATTENTION never change the internal pressure limitation device this will occur device damages ATTENTION this station must be used only in euthanasia room equipped with CO2 detection system Max Altitude of use 2000m Max humidity of use 80 This device must be used only inhouse and must be protected against flood and liquids lt must be connected on power supply protected by Ground Fault Circuit Interrupter GFCI 16A 30mA 5 Touch screen and symboles This station is equipped with a touch screen interface Tuning settin
Download Pdf Manuals
Related Search