SERVICE MANUAL DISHWASHERS - M
Contents
1. a After extracting the upper basket rotate and open the front stops remove the upper basket from the stud b Detach the spray arm from the duct using a very fine tipped screwdriver Take care not to damage the surface of the spray arm To inspect the membrane valve fitted to the duct c Use a tool to release the two rear tabs and completely detach the duct from the basket d Release the four anchor tabs which secure it to the bottom of the duct and remove th valve support d NB While remounting the spray arm pay attention not to break the plastic hooks SOI TD 8 23 599 37 44 27 4 Access from above 4 1 Drying duct fan if featured a Remove the worktop see 1 1 for the free standing dishwashers b Raise gently and detach the duct from the water fill tank taking care not to damage the sponge sealing element between the tank and the duct O Nr From inside the tub detach the intake ring by pressing the four hooks d N Carefully lift the duct and remove it e Detach the connector to the fan N f In order to inspect or replace the drive belt detach the upper cover from the fan taking care not to damage the plastic hooks b fr Il 5 Access from the front 5 1 Sliding guide for upper basket a Remove the upper basket see 3 4 a b Remove the rear arrest by releasing the anchor tab and pulling upwards c Remove the guide from the supports 5 2 C2. g a screw into the hole in the hinge so that the door remains open c Remove the wiring ties and detach the electrical connections d Remove the four screws which secure each of the hinges e Lift the inner door and remove d When replacing the inner door During this operation the hinges must remain open The locking pin should therefore be removed only after the inner door has been attached securely to the hinges SOI TD 11 23 599 37 44 27 5 6 Latch assembly a First remove the control panel see 5 2 then the two screws which secure the latch assembly to the inner door b To remove the microswitch lever the anchor tabs open and extract the switch from its housing b Important To replace the latch ferrule and or the plate remove the cap which covers the hole and remove the central screw 5 7 Integrated dispenser a First remove the external door see 5 3 and detach the electrical connections b Remove the six screws which secure the dispenser to the inner door c Press the lateral anchor tabs d Push the dispenser and remove from the interior b d SOITD 12 23 599 37 44 27 5 8 Thermostat temperature and turbidity control sensor a First remove the plinth free standing versions and the F foot support see 1 2 b Enlarge the sump hooks and slide the thermostat c Remove the electrical connectors When replacing When replacing the thermo
3. that it does not flow into the tub and the pressure switch tubes when the appliance is laid flat b Remove the following Worktop free standing versions Plinth free standing versions Foot support Front panel Lower cross member Lateral panels Adjustable feet Lay the appliance on the rear panel Remove the following from the base Adjustable central rear foot built in versions only Bottom panel if featured Anti flooding device if featured Washing motor capacitor Suppressor if featured Fill solenoid valve 23 23 rear uprights to the base and remove the uprights g Lift the tub assembly and remove from the base Detach the rubber washing motor supports Remove the screws which secure the front and rear uprights Detach the clamps in the rear section which secure the uprights h Pull the base outwards towards you 599 37 44 27
4. the upper basket see 3 4 a b From outside the tub remove the two screws which secure the basket guide wheels in position 7 3 Lateral uprights a Remove the worktop see 1 1 the plinth free standing versions and the foot support see 1 2 the lower front cross member see 7 13 and the appropriate lateral panel see 1 4 b Open the door and block in position see 5 5 b c Remove the three lateral screws from inside the tub d From the inside of the tub remove the four screws which secure the upper front cross member in position e Remove the four screws which secure the cross member at the front see 7 1 3 b f Remove the two screws which secure the hinge to the inner door see 5 5 d g Detach the earth wire and the hinge strut see 7 4 e h Remove the three lower frontal screws which secure the upright to the base i Remove the four plastic clip rivets use a tool to push the central stud of the rivet from the exterior towards the interior of the tub and remove the assemk when refitting replace the rivet if damaged j Slide the upper cross member off the upright k Remove the cross member from its seat in the base 7 4 Hinges and hinge springs Proceed as follows to replace each hinge a Remove the external door see 5 3 the worktop see 1 1 the plinth free standing versions and the foot support see 1 2 and the appropriate lateral 4 panel see 1 4 b Use a pie
5. tr DA a Lu de oem nine 9 5 1 Sliding guide for Upper baskel snss sin in inserer anses trente area nent auiene 9 5 2 Control panel ASSeMmbN ESS Rd A a scene neo uienen eme s eus desc lancia den eun ne 9 DA D NP SR E one ro 10 2o EXCMA GOO ei SEA ahs ee 11 5 4 Beam on floor fully integrated versions only if featured ccccceececesseeeeeeeeeseeeseeeeeeeaeeeesaaeees 11 Fo MOOO a ne E eo een 11 FO EACH AS CIO ssa a de D nn D ne 12 g7 JMegraeddisp pense senese ni De de loi snsideias 12 5 8 Thermostat temperature and turbidity control sensor 13 5 9 Regeneration solenoid valve slatctsseavnidtcvcen saaiaoniecutanhsiatnal vidi thda anna ant 13 O10 Salle SCNSOn I Te AtINO Es ND Meta ea 13 9 11 Drain pump non return VAIN 6 sesasine aia a aaa thaasna eee Ed a 14 5 12 Internal feed manifold to the upper spray arm 14 GO ACCESS hOM INE DASE eana a a aa aaa a a a aa E i 15 6 1 Anti flooding device if featured 15 6 2 Adjustable rear foot built in versions only 15 63 SUIMPPASSS IM DIY cee sm nr tt nn ea a seus tn 15 GA Water softening Sy Ste Masse soccer re dimanche a ann paatai 16 G20 Drain ODUM Di ZE ES er T E td des 16 T ACCESS OMANE SINGS EL nn nn de tae e a a tc dance Pr uns Meavadetoeanlde 17 Ti WWaASMING IMOOr CAD AGIlOl Mi ne le ann I lt ila cahitesiawonuys 17 7 2 Supports for upper basket wheels Vs 18 Led LateralaprigNtS paint Re nn I M nt a 18 LA TANGO AN ANGS SPO Ss ES neve dis cathe Seine macs e
6. Electrolux SERVICE MANUAL Distriparts DISHWASHERS DIVA E M A Europe Publication no DISHWASHERS Spares Operations Italy Corso Lino Zanussi 30 33080 PORCIA PN ITALY 599 37 44 27 Fax 39 0434 394096 60cm PNC 911 5 EN ACCESSIBILITY Edition 2005 12 Production PLV Zarow Poland SOI TD 1 23 599 37 44 27 SOITD 2 23 599 37 44 27 CONTENTS CC aera on en ene eee ren 4 1 1 To access the components from above first remove the worktop free standing versions only 4 1 2 To access the components housed in the base from the front of the appliance free standing METS IOINS Se MR Se den toit 4 1 3 To access the components housed in the base from the lower section remove the bottom panel Uincerc Lib gere as IOIONSS mene neste ee eee ter ie ee cen a E ee ey eee 4 1 4 To access components from the side remove the relative lateral panel 5 2 STR CTURAL EHARACTERISTICS Sn Leon amet 5 2 DOOF ATARI nn US A a Ne eae 6 2 2 BaSe OO eee se ate a eee E A a eee eee 6 Zed PUD ATOS SNS nn An ee aed echt A et ns T 3 Open ihe door to access the ToloWiNg ist aene ie ist A A T Sale Conraldrani Merine a A E a a eee cde 8 32 Large washing ISSN ds niet ia 8 L MONET SDrAV ATTIE S ne a NN Ne SN A ill Ne ie 8 51011 Le VE Lila n AMG CU APR RS RD steno iiaesnen 8 A ACCESS TON DOW C ES as ros E le Neon tea en ciel tem es tn nine 9 A Ding du uctifan ir ALU Re Neue deniers 9 S ACCESS HOME TONER RS RS
7. anels the plinth free standing versions only and the foot support Removal of these parts facilitates access to the internal components from above from the front from the sides and from the base of the appliance 2 1 Door area Control panel assembly External door Internal door Hinge Hinge pin Lower door seal Door latch assembly Integrated dispenser DO COCO DODDO 2 2 Base area Base Removable bottom panel if featured Adjustable feet Foot support Adjustable rear foot central built in and fully integrated versions Electronic board Anti flooding device if featured Wash pump capacitor Integrated terminal block power cable suppressor Washing motor Tube enclosed heating element Drain pump Drain pump non return valve Fill solenoid valve if featured Regeneration solenoid valve Plinth free standing versions Water softening system Salt sensor if featured Level pressure switch Anti overflow pressure switch D D UD DO OO OU DO DO DO DO DO OU UU SOITD 6 23 599 37 44 27 2 3 Tub area a Tub Fitted externally to the tub a Lateral uprights Upper rear cross member Upper front cross member Lower front cross member Supports for upper basket wheels External feed manifold to the upper spray arm Sump assembly Thermostat temperature sensor turbidity sensor Water fill tank short or long Drying duct fan if featured D UD DU OU 0 Fitted inside the tub a Sliding guides for upper bas
8. ateral panels see 1 4 b Remove the four screws which secure the upper cross member frontally c From inside the tub remove the four upper screws see 7 3 d d Remove the cap which covers the hole for the latch remove the central screw the plaque and the bridging plug e Pull the upper cross member upwards and away from the lateral uprights b Important To replace the latch ferrule and or the plate which are secured to the tub simply remove the central screw SOI TD 22 23 599 37 44 27 8 Replacing the tub a From inside the tub remove the following Lower basket Upper basket Wheel guides for the upper basket Steam venting ring sealing ring softening unit cap and ring sealing ring Latch cover Drain filter Washing filter Lower spray arm Spray arm support column Internal feed manifold c Remove the following Worktop free standing versions Door assembly Plinth free standing versions Foot support Lower cross member Lateral panels d From inside the tub remove the two screws which secure the sump e Remove the six screws which secure the hinge uprights to the base From outside the tub remove the following Upper front cross member f Remove the two screws which secure the Upper rear cross member Upper basket wheel supports Door hinge springs Door hinges Drying duct fan 9 Replacing the base SOl TD a Remove any residual water from the sump by suction so
9. base from the lower section remove the bottom panel if featured as follows a Remove the inner filters see 3 1 and 3 2 b Remove any residual water from the sump by suction so that it does not flow into the tub and the pressure switch tubes then lay the appliance on its rear panel c Unscrew and remove the regulation screw from the rear foot built in versions only d Remove the screws which secure the bottom panel to the base e Release the built in retaining elements placed on the right and rear side and remove the bottom panel by sliding to the right SOl TD 4 23 599 37 44 27 1 4 To access components from the side remove the relative lateral panel a First remove the worktop see 1 1 the plinth free standing versions and the foot support see 1 2 b Remove the three rear screws the upper and the lower front c Detach the lateral panel from the rear and slide away from the frontal anchor slot NB Before laying the dishwasher on a side panel or on the rear panel suck the water in the sump for example by using a syringe so as the water does not reach the pressure switch tube or the tub 2 STRUCTURAL CHARACTERISTICS SOI TD 5 23 599 37 44 27 The appliance may be considered as consisting of three major assemblies DOOR AREA BASE AREA TUB AREA The entire structure is enclosed by a series of removable parts such as the worktop free standing versions only the door two lateral p
10. ce of wire or string to detach the tensioner spring from its seat on the upright c Remove the two screws which secure the hinge to the inner door see 5 5 d d Remove the screw which secures the hinge to the upright e Pull and detach the hinge pin and the earth wire When replacing Fit the spring to the hinge then using a piece of string and a pair of pliers attach it to the hook on the upright SOITD 18 23 599 37 44 27 7 5 Water fill tank a From inside the tub unscrew the steam venting ring b Remove the worktop see 1 1 the plinth and the foot support see 1 2 and the left hand lateral panel see 1 4 Detach the tube to the fill solenoid c Detach the fill tank from the drying duct if featured see 4 1 d Pull the fill tank upwards taking care not to damage the O rings on the couplings to the water softener and the tub When replacing When replacing the water fill tank lubricate the O rings and position them correctly on the male part of the coupling d 7 6 Washing motor a Remove any residual water from the sump by suction so that it does not flow into the tub and the pressure switch tubes when the appliance is laid on the rear panel b Remove the worktop see 1 1 the plinth free standing versions and the foot support see 1 2 the bottom panel see 1 3 and the anti flooding device see 6 1 if featured and the right hand lateral panel see 1 4 c Lay the applian
11. ce on the rear panel d Detach the electrical connections to the start up capacitor e Remove the hoses for the sump and the heating element f From below detach the two rubber motor supports from the base g Slide the motor laterally from the right 9 When replacing When replacing the motor reposition the hose clamps correctly and check for leaks SOI TD 19 23 599 37 44 27 7 7 Level anti overflow pressure switches and support a Remove the worktop see 1 1 the plinth free standing versions and the foot support see 1 2 b From the front detach the electrical and hydraulic connections from the pressure switch to be replaced c Using a tool carefully detach the pressure switch from the support and slide it downwards d To remove the entire pressure switch support first remove the right e Remove the screw which secures the support for the pressure switches to the upright f Using a tool release the two plastic anchors from the upright and remove the support g If it is necessary to perform electrical tests on the pressure switches before replacing the switches detach the hydraulic connections and remove the support see above move the switch to the front for testing When replacing Reposition the pressure switches correctly on the support and re fit the hydraulic connections Ensure that the rubber elements between the pressure switch and the support are correctly inser
12. e encase Sewanee nes ete ie new cals set ee dns 18 Ces NAIL 19 EO NASA FINO OM cess arte sa ete cee cea ete ee eee eee 19 7 7 Level anti overflow pressure switches ANd support 20 7 8 Tube enclosed heating element ss 20 7 9 Fill solenoid valve if T L RE en no deanncnes diese les dues haies ne ciune 21 7 10 Power cable and terminal block with integrated suppressor ss 21 1 411 LoW r1trontcross members nn an a ores see Sie 21 1 12 Upper rear CFOSS MEMDEN sde eave eta eee on 22 7 13 pperfrontcross m mbher sise at E si aves ad aa 22 9 FREDIACING Me UD te sat om tete ti een 23 9g FREDIACING N Dase Sa AM tatin steel nn eo OA 23 Repairs to electrical appliances must be effected by qualified personnel only Before accessing internal components remove the plug from the power socket SOI TD 3 23 599 37 44 27 1 ACCESSIBILITY 1 1 To access the components from above first remove the worktop free standing versions only a Remove the two screws from the rear section b Push the top forwards and release 1 2 To access the components housed in the base from the front of the appliance free standing versions a Remove the 5 lower plastic hooks starting from one side b Open the door to free the plinth c Rotate it and extract it Foot support d Remove the 6 fixing screws and remove it paying attention not to damage the external door 1 3 To access the components housed in the
13. e lip of the water softener and the seals on the connection with the water fill tank Lubricate the seals 6 5 Drain pump a Remove any residual water from the sump by suction so that it does not flow into the tub and the pressure switch tubes then lay the appliance on the rear panel b First remove the plinth free standing versions the foot support see 1 2 and the bottom panel if featured see 1 3 c Working from the front use pliers to detach the sump hose from the corrugated drain hose detach the electrical connectors SOITD 16 23 999 37 44 27 d Using a tool such as a flat head screwdriver detach the two anchor tabs on the body of the pump one at a time Care should be taken to avoid damaging or breaking the anchor tabs Remove the pump from its seat When replacing Mount the sleeve correctly to the sump and the drain tube Check for leaks by performing a test cycle d 7 Access from the sides RIGHT SIDE VIEW LEFT SIDE VIEW 71 Washing motor capacitor a Remove the worktop see 1 1 the plinth and the foot support see 1 2 and the right side panel see 1 4 b Remove the protective cap and detach the electrical connectors c Pull the capacitor upwards to remove it from its seat in the base SOl TD 17 23 999 37 44 27 7 2 Supports for upper basket wheels a Remove the worktop see 1 1 the plinth and the foot support see 1 2 the appropriate lateral panel see 1 4 and
14. he two hose wings from the steel plate on the rear panel of the tub b Turn it right c Extract the internal manifold from the spray arm support column without damaging it SOl TD 14 23 999 37 44 27 6 Access from the base NB Before laying the dishwasher on a side panel or on the rear panel remove the water in the sump by suction for example with a syringe so as it does not reach the pressure switch tubes or the tub 6 1 Anti flooding device if featured a Remove the bottom panel if featured see 1 3 b Lift up and release the anchor tab c To replace the microswitch lever the tabs open and remove 6 2 Adjustable rear foot built in versions only a Remove any residual water from the sump by suction so that it does not flow into the tub and the pressure switch tubes then lay the appliance on the rear panel b Remove the regulation screw from the bottom panel see 1 3b c Using a tool detach the foot support and slide away from the base 6 3 Sump assembly a Remove any residual water from the sump by suction so that it does not flow into the tub and the pressure switch tubes when the appliance is laid on the rear panel b Remove the plinth free standing versions and the foot support see 1 2 c From inside the tub remove the basket and the lower spray arm see 3 3 d Remove the central drain filter see 3 1 and the large washing filter See 3 2 e f e Re
15. ket Central drain filter Large washing filter Lower spray arm Upper spray arm Internal feed manifold to the upper spray arm Upper lower basket Cap for water softening system Steam venting ring D D DU D DU DECO 3 Openthe door to access the following Guides wheel supports for upper basket Regulation knob for water softening system Salt reservoir cap Integrated detergent rinse aid dispenser Control panel assembly Serial number plate Central drain filter Large washing filter 9 Lower spray arm 10 Upper spray arm 11 Upper lower basket 12 Worktop free standing versions only ONDES SYS When replacing the EASY LIFT drum regulation assemblies it is advisable to immerse them in hot water for a few minutes since they are easier to fit when softened SOI TD 7 23 599 37 44 27 3 1 Central drain filter a From inside the tub use the lever to rotate the filter assembly atb c about 45 in a counter clockwise direction and remove the assembly from its housing b Use the central ring to pull the coarse mesh filter a and remove from the fine mesh filter b Separate the microfilter c from filter a 3 2 Large washing filter a After removing the central drain filter see 3 1 remove the filter d from the bottom of the tub 3 3 Lower spray arm a After removing the lower basket pull the spray arm upwards gripping it by the central hub 3 4 Upper spray arm and duct
16. move the two screws which secure the spray arm support column and remove the column f Remove the two screws which secure the tub to the sump g Remove the baffom panel if featured see 1 3 h Remove the gnti flooding device if featured see 6 1 i Detach all the hoses to the heating element the water softener the washing motor the drain pump and the pressure Poe j Remove the thermostat and the O ring see 5 8 SOITD 15 23 599 37 44 27 k Detach the drain pump see 6 5 Pull the sump out taking care not to damage the tub seal When replacing When replacing the sump position the seals correctly and lubricate The seals should preferably be fitted first to the male section of the coupling 6 4 Water softening system a Working from inside the tub remove the cap of the softening system and the ring located beneath the cap b Remove any residual water from the pump by suction so that it does not flow into the tub and the pressure switch tubes c Remove the plinth free standing versions the foot support see 1 2 and the left lateral panel see 1 4 and lay the appliance on the rear panel and remove the cabinet bottom see 1 3 d Detach the hose which connects the softener to the sump and remove any wiring ties Detach the electrical connectors e Pull the water softener outwards When replacing When replacing the water softener position the seal correctly on th
17. ontrol panel assembly a Remove the door and then remove the six self tapping screws which secure the control panel to the inner door b Supporting the control panel assembly remove from the inner door c Detach the electrical connections The following components if featured are fitted inside the control panel and secured by screws or pressure fitted a Power display board Q Knob assembly SOl TD 9 23 599 37 44 27 5 2 1 PCB a Detach the electrical connections b Slide away and remove the knob flange assembly paying attention not to damage the components c Remove the 2 screws which secure it to the control panel d Use a tool to release the four lateral anchor tabs e Remove the board and its casing from the control pane SOl TD 10 23 999 37 44 27 5 3 External door a Open the door and remove the six perimetral screws which secure it to the inner door b Remove the two lateral screws c Slide the external door forwards and remove b 5 4 Beam on floor fully integrated versions only if featured a Remove the external door see 5 3 b Remove the screw which secures the plastic support to the door hinge c Detach the support from the hinge strut d Remove the wiring tie and disconnect the beamer 5 5 Inner door a Remove the external door see 5 3 the control panel see 5 2 and the integrated dispenser see 5 7 b Open the door and insert a locking pin e
18. stat first lubricate the seal and then position it correctly on the sensor Insert the assembled parts taking care to ensure that the seal does not enter the sump Important Check that the anchor tabs return to their original position 5 9 Regeneration solenoid valve a First remove the plinth free standing versions and the foot support see 1 2 Important The softening system will contain a quantity of water Before removing the solenoid valve this water should be removed by suction b Turn the solenoid valve counter clockwise until it exits its housing c Remove the connectors When replacing When replacing the solenoid valve lubricate the O ring and position it correctly on the valve insert the valve into the seat and turn clockwise until is locks into position 5 10 Salt sensor if featured a First remove the plinth free standing versions and the foot support see 1 2 b Detach the electrical connectors from the sensor c Using a tool release the salt sensor from the water softener and slide it downwards SOl TD 13 23 599 37 44 27 5 11 Drain pump non return valve a First remove the plinth free standing versions and the foot support see 1 2 b Detach the corrugated tube from the drain pump removing the plastic clamp c The membrane valve is mounted on the body of the drain pump 5 12 Internal feed manifold to the upper spray arm a From inside the tub release t
19. ted 7 8 Tube enclosed heating element a Remove any residual water from the sump by suction so that it does not flow into the tub and the pressure switch tubes when the appliance is laid on the rear panel b Remove the plinth free standing versions and the foot support see 1 2 the bottom panel see 1 3 the anti flooding device see 6 1 if featured and the right hand lateral panel see 1 4 then lay the appliance on the rear panel d c Detach the electrical connections d From the right hand side detach the hose connected to external manifold e From below detach the hose connected to the sump f Form the right hand side slide out the heating element When replacing Ensure that the hoses are fitted correctly and that the hose clamps are secured tightly SOI TD 20 23 599 37 44 27 79 Fill solenoid valve if featured a Disconnect the appliance from the water supply Unscrew the fill hose from the solenoid valve Important residual water may spill from the hose b Remove the two rear screws which secure the valve to the base c Remove the left hand lateral panel see 1 4 and detach the solenoid valve from the hose to the water fill tank i b d From the left hand side grip the solenoid valve and while at the same time pushing it from the rear turn it clockwise until it is released d 7 10 Power cable and terminal block with integrated suppressor Proceed as follo
20. ws to replace the power cable a Remove the cover from the terminal block located in the rear section To do so use a tool to release the two plastic tabs and slide the terminal block to the right b Loosen the screw on the cable clamp detach the electrical connections and pull the power cable free Proceed as follows to replace the integrated terminal block A Remove the worktop see 1 1 the plinth free standing versions and the foot support see 1 2 and the left hand lateral panel see 1 4 then lever the anchor tab towards the centre of the appliance and lift the terminal block B Detach the electrical connections and remove the terminal block from the left 7 11 Lower front cross member a Remove the worktop see 1 1 the plinth free standing versions and the foot support see 1 2 and both lateral panels see 1 4 b Remove the four screws which secure the cross member in position SOITD 21 23 999 37 44 27 7 12 Upper rear cross member a Remove the worktop see 1 1 the plinth see 1 2 and both lateral panels see 1 4 b Remove the two upper screws which secure the cross member to the tub c Detach the plastic clips which secure the cross member to the lateral sheet metal reinforcement plates d Pull the cross member upwards and away from the rear uprights NM x y 17 a 7 13 Upper front cross member a Remove the worktop see 1 1 the plinth see 1 2 and both l
Download Pdf Manuals
Related Search