Kvaser Memorator Pro 5xHS User's Guide
Contents
1. Kvaser Memorator Pro 5xHS User s Guide Copyright 2014 2015 Kvaser AB M lndal Sweden http Awww kvaser com Printed Monday 2 February 2015 We believe that the information contained herein was accurate in all respects at the time of printing Kvaser AB cannot however assume any responsibility for errors or omissions in this text Also note that the information in this document is subject to change without notice and should not be construed as a commitment by Kvaser AB Kvaser Memorator Pro 5xHS User s Guide This page is intentionally left blank cere Kvaser AB M lndal Sweden www kvaser com 2 26 Kvaser Memorator Pro 5xHS User s Guide Contents 1 About this manual 2 Introduction 2 1 Welcome to Kvaser Memorator Pro5xHS 2 2 Major features a 36 eS eG ee we oe a ee ol we ws 2 3 Interface andlogger 0 2 2000 2 4 Configuration software inthe PC 2 5 Thetprogramming language 4 2 6 Additional software and documentation 3 Kvaser Memorator Pro 5xHS hardware 3 1 Hardware installation 0000 3 2 USBconnector 0 0 00 0 2 ee eee 3 3 CANchannels 0 0000 ee eee ee 3 4 External trigger 00 0200000 3 5 Power supply 22 058 22 6228 824 42 0480 28 4 62 64 8 36 oD G rd 4 4 26a 6 BSS Ew AY ES BRD 3 7 LED Indicators s is sv c 6 ske rok AR bee eae a 3 8 Troublesho2. by using all red Traffic LEDs simultaneously LED Label Color Power PWR Green Yellow Traffic CAN Yellow red Table 2 The different type of LEDs The following definitions is used to describe the state of an LED Off The LED is off and no light is emitted Flash The LED is lit up during a very short time A single flash may be hard to see and a continuous set of flashes will be look the same as On Slow Blink The LED is repeatedly turned On and Off The On and Off phase is equal in time Fast Blink The LED is repeatedly turned On and Off but with a higher frequency than Slow Blink The On and Off time is still equal On The LED is constantly emitting light Slow Waver This is a variant of Slow Blink but instead of being Off a second color is On This is only possible with a dual colored LED Fast Waver The LED is alternating between two colors as in Slow Waver but using a higher frequency Running This means that all LEDs are lit one at the time in sequence with every color available i e Power green gt Power yellow gt Traffic 1 yellow gt Traffic 1 red gt Traffic 2 yellow gt Traffic 2 red gt As an example Slow Waver Green Yellow means that the LED is slowly blinking by alternating between green and yellow Nemme Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 13 26 4 1 1 Interface mode The device is in Interface mode when it is connected to the PC via USB If
3. on the CAN bus triggered by identifier data contents or error frames Pre and post trigger times can be set To enhance logging performance Kvaser Memorator Pro 5xHS can filter out messages to be logged The identifiers can be picked from a database file or all messages can be logged 2 4 Configuration software in the PC To be able to configure Kvaser Memorator Pro 5xHS you need to install Kvaser Memorator Config Tool which can be downloaded at http www kvaser com download The Kvaser Memorator Config Tool will assist in e Configuration of the CAN controller e g bit rate and filters crore Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 7 26 Configuration of the trigger conditions Configuration of filter for messages to be stored Configuration of t programs to be started Downloading configuration via USB Extracting logged messages via USB or SD card Converting files logged in Kvaser Memorator Pro 5xHS to several different formats For a detailed description and how to get started see the on line help availible inside Kvaser Memorator Config Tool 2 5 Thet programming language The Kvaser t programming language is event oriented and modeled after C It can be used to customize the behavior of the Kvaser Memorator Pro 5xHS and other Kvaser t capable devices A t program is invoked via hooks which are entry points that are executed at the occurrence of certa
4. www kvaser com download Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 21 26 Connect the Kvaser Memorator Pro 5xHS to your PC with the USB cable and start the update exe application A window opens showing the Firmware Update Instructions read and follow those carefully To check the current firmware version open Kvaser Hardware which can be found in the Control Panel Select Kvaser Memorator Pro 5xHS in the tree view to the left and click on the channel The firmware revision information now appears in the right half of the window cere Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 22 26 5 Disposal and Recycling Information A Advanced CAN Solutions When this product reaches its end of life please dispose of it according to your local environmental laws and guidelines Dispose of batteries according to your local environmental laws and guidelines For information about Kvaser s recycling programs visit http www kvaser com en kvaser recycling policy html Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 23 26 6 Legal acknowledgements 6 1 Advanced CAN Solutions Usage warning WARNING FOR ALL USERS WARNING YOUR USE OF THIS DEVICE MUST BE DONE WITH CAUTION AND A FULL UNDERSTANDING OF THE RISKS THIS WARNING IS PRESENTED TO INFORM YOU THAT THE OPERATION OF TH
5. B 9 PIN Figure 8 Example of how to connect a button to the External trigger input Internally the External trigger input has a pull up to 5 V see Figure 9 DnA TRIG IN 4 il i Ll R 3 2 mammaire 2 TRIGG NPI F VT 25 TRIGGER INPUT SON CANI PINGA DI Figure 9 The External trigger input inside the Kvaser Memorator Pro 5xHS Advanced CAN Solutions Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 20 26 4 7 External trigger output The Kvaser Memorator Pro 5xHS can be set up to send an external pulse through the External trigger output pin See Section 4 4 CAN connectors on Page 16 for pin numbering GND ie nF if nF 24V H 78L05 T0220 270 OHM LED CAN 2 DSUB 9 PIN Figure 10 Sample circuit for connecting a LED to the External trigger output 3 3V R1 10K LI R4 dlani 75 TRIGGER OUTPUT Con CAN PIN a E 7 Ls 120 mA i 2 4 3 10 TRIG OUT 2 13 3 Pe 1 i 49 1 CON CAN2 PIN 3 GND CAN Figure 11 The External trigger output inside the Kvaser Memorator Pro 5xHS 4 8 Updating the firmware For the Kvaser Memorator Pro 5xHS to communicate with the host computer compatible versions of the Kvaser CANIlib including driver and firmware must be installed The latest versions of firmware and drivers can be downloaded for free at http
6. IS DEVICE MAY BE DANGEROUS YOUR ACTIONS CAN INFLUENCE THE BEHAVIOR OF A CAN BASED DISTRIBUTED EMBEDDED SYSTEM AND DEPENDING ON THE APPLICATION THE CONSEQUENCES OF YOUR IMPROPER ACTIONS COULD CAUSE SERIOUS OPERATIONAL MALFUNCTION LOSS OF INFORMATION DAMAGE TO EQUIPMENT AND PHYSICAL INJURY TO YOURSELF AND OTHERS A POTENTIALLY HAZARDOUS OPERATING CONDITION IS PRESENT WHEN THE FOLLOWING TWO CONDITIONS ARE CONCURRENTLY TRUE THE PRODUCT IS PHYSICALLY INTERCONNECTED TO A REAL DISTRIBUTED EMBEDDED SYSTEM AND THE FUNCTIONS AND OPERATIONS OF THE REAL DISTRIBUTED EMBEDDED SYSTEM ARE CONTROLLABLE OR INFLUENCED BY THE USE OF THE CAN NETWORK A POTENTIALLY HAZARDOUS OPERATING CONDITION MAY RESULT FROM THE ACTIVITY OR NON ACTIVITY OF SOME DISTRIBUTED EMBEDDED SYSTEM FUNCTIONS AND OPERATIONS WHICH MAY RESULT IN SERIOUS PHYSICAL HARM OR DEATH OR CAUSE DAMAGE TO EQUIPMENT DEVICES OR THE SURROUNDING ENVIRONMENT WITH THIS DEVICE YOU MAY POTENTIALLY e CAUSE A CHANGE IN THE OPERATION OF THE SYSTEM MODULE DEVICE CIRCUIT OR OUTPUT e TURN ON OR ACTIVATE A MODULE DEVICE CIRCUIT OUTPUT OR FUNCTION TURN OFF OR DEACTIVATE A MODULE DEVICE CIRCUIT OUTPUT OR FUNCTION INHIBIT TURN OFF OR DEACTIVATE NORMAL OPERATION MODIFY THE BEHAVIOR OF A DISTRIBUTED PRODUCT ACTIVATE AN UNINTENDED OPERATION PLACE THE SYSTEM MODULE DEVICE CIRCUIT OR OUTPUT INTO AN UNINTENDED MODE ONLY THOSE PERSONS WHO A ARE PROPERLY TRAINED AND QUALIFIED WITH RES
7. PECT TO THE USE OF THE DEVICE B UNDERSTAND THE WARNINGS ABOVE AND C UNDERSTAND HOW THIS DEVICE INTERACTS WITH AND IMPACTS THE FUNCTION AND SAFETY OF OTHER PRODUCTS IN A DISTRIBUTED SYSTEM AND THE APPLICATION FOR WHICH THIS DEVICE WILL BE APPLIED MAY USE THE DEVICE PLEASE NOTE THAT YOU CAN INTEGRATE THIS PRODUCT AS A SUBSYSTEM INTO HIGHER LEVEL SYSTEMS IN CASE YOU DO SO KVASER AB HEREBY DECLARES THAT KVASER AB S WARRANTY SHALL BE LIMITED TO THE CORRECTION OF DEFECTS AND KVASER AB HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY OVER AND ABOVE THE REFUNDING OF THE PRICE PAID FOR THIS DEVICE SINCE KVASER AB DOES NOT HAVE ANY INFLUENCE ON THE IMPLEMENTATIONS OF THE HIGHER LEVER SYSTEM WHICH MAY BE DEFECTIVE THIS PRODUCT CONTAINS A RECHARGEABLE LI POL BATTERY THAT MUST BE DISPOSED OF PROPERLY IT MAY EXPLODE IF DAMAGED OR DISPOSED OF IN FIRE DO NOT SHORT CIRCUIT Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 24 26 6 2 EC Regulatory Compliance The product s 73 301 30 00778 9 is in conformity with the essential requirements of the following regulations and directives e DIRECTIVE 2012 19 EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 WEEE e REGULATION EC No 1907 2006 REACH Annex XIV the Candidate list and Annex XVII Restriction of Substances The products listed above also complies with DIRECTIVE 2011 65 EU OF THE EUROPEAN PARLIAMENT AND OF THE CO
8. Pro 5xHS to send an external pulse of configurable length as an action for a trigger event See also Section 4 6 External trigger input on Page 18 and Section 4 7 External trigger output on Page 20 3 5 Power supply The Kvaser Memorator Pro 5xHS can be powered through the CAN connector and through the USB connector To operate the Kvaser Memorator Pro 5xHS in logger mode you must supply power through the CAN connector To use the device as a USB CAN interface or to configure the device power on the USB side is sufficient See Section 4 4 CAN connectors on Page 16 for information on how to connect power to the connector The supply power should be in the range specified in Section 4 3 Technical data on Page 15 3 6 SD Card You can use SD SDHC and SDXC cards with your Kvaser Memorator Pro 5xHS for logging The Kvaser Memorator Pro 5xHS is built with industrial environments in mind but please note that the SD card used can be a limiting factor By using a quality card that matches the specifications of the Kvaser unit you minimize the risk for data corruption or lost data es t Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 10 26 Insert the SD card upside down into your Kvaser Memorator Pro 5xHS see Figure 4 on Page 10 Do not apply excessive force To remove the SD card open the access door and using a finger or a small coin gently press on the edge of the SD card until a
9. UNCIL of 8 June 2011 RoHS and is in conformity with the following standards and or other normative documents Standard Description EN 50 581 2012 Assessment with respect to restriction of hazardous substances Table 10 Standards and normative documents for RoHS 2011 The products listed above also complies with DIRECTIVE 2004 108 EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 EMC directive and is in conformity with the following standards and or other normative documents Standard Description EN 55 022 2010 Class B radiated IT equipment commercial emission EN 55 024 2010 IT equipment commercial immunity EN 61 000 6 2 2005 Generic industrial immunity Table 11 Standards and normative documents for EMC 2004 NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his her own expense 6 3 Patents Copyrights and Trademar
10. ator Pro 5xHS does not contain any CAN bus termination because their inclusion could cause severe disturbance in a system which is already correctly terminated For laboratory or testing use the exact value of the termination resistors is not always critical Sometimes a single terminator is sufficient For production proper termination is essential If you see error frames on the bus you should check the termination To save yourself a lot of trouble always terminate the CAN A bus properly 4 6 External trigger input The Kvaser Memorator Pro 5xHS can be set up to trigger on an external signal and can be configured to react on both falling and rising edges e If it is set to trigger on a falling edge the trigger is activated when the External trigger is connected to ground es K Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 19 26 e If itis set to trigger on a rising edge the trigger is activated when the External trigger is disconnected from ground There are two ways to create such an external signal either connect a switch from the External trigger input on CAN channel 1 to ground or connect a signal between 0 and 5 V to the External trigger input See Section 4 4 CAN connectors on Page 16 for pin numbering The trigger input is debounced by the firmware so that a pulse of shorter length than approximately 30 ms will not be detected Swi o PUSHBUTTON CAN 1 DSU
11. be inserted in any free USB socket on the host computer You do not need to switch the power off before inserting or removing the device For the Kvaser Memorator Pro 5xHS to communicate with the host computer the correct version of the Kvaser driver and firmware must be installed The firmware is downloaded and installed directly on the Kvaser Memorator Pro 5xHS and the driver is installed on the host computer The latest version of the driver and firmware can be downloaded from http www kvaser com download The driver is installed by running the file kvaser_drivers_setup exe For information on how to upgrade the firmware see Section 4 8 Updating the firmware on Page 20 3 2 USB connector The Kvaser Memorator Pro 5xHS has a standard USB type Micro B female connector Figure 2 Micro USB cable connected to the Kvaser Memorator Pro 5xHS 3 3 CAN channels The Kvaser Memorator Pro 5xHS has five CAN Hi Speed channels in a single 26 pin HD D SUB CAN connector see Figure 3 on Page 9 See Section 4 4 CAN samen Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 9 26 connectors on Page 16 for pinout information Figure 3 CAN connector on Kvaser Memorator Pro 5xHS 3 4 External trigger The Kvaser Memorator Pro 5xHS can be set up to trigger on an external input signal where the edge can be configured for rising or falling It is also possible to configure the Kvaser Memorator
12. click is heard Release the card and it will partially eject Remove the SD card completely Figure 4 Inserting SD card into the Kvaser Memorator Pro 5xHS 3 7 LED Indicators The Kvaser Memorator Pro 5xHS has one power LED and one traffic LED for each CAN channel as shown in Figure 5 Their functions are described in Section 4 1 Definitions of LED states and colors on Page 12 Figure 5 LEDs on the Kvaser Memorator Pro 5xHS Nerd Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 11 26 3 8 Troubleshooting Use Kvaser Hardware in the Control Panel to verify that the computer can communicate with the Kvaser Memorator Pro 5xHS if the firmware version shown is all zeroes there are communication problems If the LEDs are not flashing or not light up at all check the power supply cere Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 12 26 4 Appendices In this section you will find technical information about the Kvaser Memorator Pro 5xHS and its connectors 4 1 Definitions of LED states and colors A Kvaser device has two basic types of LEDs Power and Traffic These are dual colored as shown in Table 2 A device with multiple CAN channels has one Traffic LED for each CAN channel When the device has more than one channel a space and digit is added on the label CAN 1 CAN 2 etc The red Traffic LEDs are also used to indicate errors
13. connectors Kvaser Memorator Pro 5xHS devices that uses the 26 pin HD D SUB connector see Figure 6 has the pinning described in Table 9 on Page 17 This table also describes how the HD26 5xDS9 Splitter see Figure 7 on Page 18 connects to five seperate 9 pin DSUB connectors CAN 1 to CAN 5 10000000009 0000000 0018 000000005 Figure 6 The 26 pin HD D SUB connector pin numbers Advanced CAN Solutions Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 17 26 HD D SUB CAN1 CAN2 CAN3 CAN4 CAN5 Function 1 2 CAN_L channel 1 2 2 CAN_L channel 2 3 2 CAN_L channel 3 4 2 CAN_L channel 4 5 2 CAN_L channel 5 6 Not connected 7 Not connected 8 4 External trigger input 9 Not connected 10 9 Power supply to the device 11 7 CAN_H channel 1 12 Y CAN_H channel 2 13 7 CAN_H channel 3 14 7 CAN_H channel 4 15 7 CAN_H channel 5 16 Not connected 17 Not connected 18 4 External trigger output 19 3 GND channel 1 20 3 GND channel 2 21 3 GND channel 3 22 3 GND channel 4 23 3 GND channel 5 24 Not connected 25 Not connected 26 Not connected Table 9 Pin configuration of the 26 pin HD D SUB and HD26 5xDS9 splitter cerca Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 18 26 Figure 7 The HD26 5xDS9 Splitter 4 5 CAN bus termination Every CAN bus must be terminated with a 120 Ohm resistor at each end of the bus The Kvaser Memor
14. cript can override any of the existing LEDs and create notifications as needed when the t program is running including program exceptions One action can not be handled by the script developer and that is when at program has failed to load and never started This is instead included in the indication of Configuration file missing or corrupt see Table 6 4 2 Start and stop of t programs All events that a t program will react to are specified using various event hooks In effect these are functions which are called when the specific events occur Among other events the program can react to starting and stopping itself which this 3This should not normally happen 4This also includes the case where a t program failed to load and start as configured Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 15 26 section describes Read the Kvaser t Programming Language guide that can be downloaded at http www kvaser com download for more information The on start event will be triggered in the Kvaser Memorator Pro 5xHS when any of the following occurs When a t program is started using the CANlib API kvScriptStart e When at program is started from another t program e When Kvaser Memorator Pro 5xHS is powered on into Logger mode e When using CANIib API kvDeviceSetMode kvDEVICE_MODE_LOGGER The on stop event will be triggered for running t programs during the corresp
15. eption of standard and extended CAN messages on the bus with a high time stamp precision Kvaser Memorator Pro 5xHS can also be used as a powerful multi channel real time CAN to USB interface It is compatible with applications that use Kvaser s CANIib This guide applies to Kvaser Memorator Pro 5xHS devices listed in Table 1 on Page 6 Nerd Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 6 26 Device Product Number EAN Kvaser Memorator Pro 5xHS 73 30130 00778 9 Table 1 Kvaser Memorator Pro 5xHS devices and their product numbers 2 2 Major features e USB CAN interface e Quick and easy plug and play installation e Supports both 11 bit CAN 2 0A and 29 bit CAN 2 0B active identifiers e 100 compatible with applications written for other Kvaser CAN hardware with Kvaser CANIib e High speed CAN connection compliant with ISO 11898 2 up to 1 Mbit s e Fully compatible with J1939 CANopen NMEA 2000 and DeviceNet e Simultaneous operation of multiple devices e One SD card slot for logging e Logger status is indicated with externally visible LEDs 2 3 Interface and logger Kvaser Memorator Pro 5xHS provides a CAN bus interface through a standard USB interface it also makes it possible to log data from a CAN bus to a standard SD card Kvaser Memorator Pro 5xHS can log continuously or logging can be triggered by external triggers rising or falling edge and or by messages
16. in events These events can be for example the arrival of specific CAN messages timer expiration or external input Like any Kvaser CAN interface the Kvaser Memorator Pro 5xHS can be used via CANIib on a PC The addition of t programs running directly on the Kvaser Memorator Pro 5xHS makes it possible to react much quicker to CAN bus events for example to speed up file transfer protocols or to simulate missing hardware The Kvaser Memorator Pro 5xHS can also operate completely autonomously For more information see the Kvaser t Programming Language guide that can be downloaded at http www kvaser com download 2 6 Additional software and documentation The Kvaser CANlib SDK includes everything you need in order to develop software for the Kvaser CAN hardware It contains full documentation and many sample programs written in C C C Delphi Python and Visual Basic All Kvaser CAN interface hardware share a common software API Programs written for one device type will run without modification on other device types The latest versions of documentation software and drivers can be downloaded for free at http www kvaser com download cere Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 8 26 3 Kvaser Memorator Pro 5xHS hardware In this section you can read more about the CAN channels power supply and LED indicators 3 1 Hardware installation The Kvaser Memorator Pro 5xHS may
17. ks All trademarks are the property of their respective owner Windows is a registered trademark of Microsoft Corporation in the United States and other countries crore Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 25 26 Adobe the Adobe logo and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries DeviceNet is a Trademark of Open DeviceNet Vendor Association Inc NMEA 2000 is the registered trademark of the National Marine Electronics Association Inc cere Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 26 26 7 Document Revision History Version history for document UG 98165 memorator pro uvp Revision Date Changes 1 0 2015 01 30 Initial version KVASER Meme Kvaser AB M lndal Sweden www kvaser com
18. onding cases e When a t program is stopped using the CANlib API kvScriptStop e When at program is started from another t program e When Kvaser Memorator Pro 5xHS is powered off in Logger mode after configured afterburner expires When using CANIib API kvDeviceSetMode kvDEVICE_MODE_INTERFACE When USB power is connected or removed CAN power is applied 4 3 Technical data In Table 8 on Page 16 below you will find the Kvaser Memorator Pro 5xHS s technical specifications cere Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide CAN Channels CAN Transceivers CAN Controller Galvanic isolation CAN Bit Rate Time stamp resolution Max message rate Error Frame Detection Error Frame Generation Silent mode PC interface External power Power consumption Hardware configuration Software requirements Dimensions Weight Operating temperature Storage temperature Relative humidity 16 26 5 TJA1051T Compliant with ISO 11898 2 Kvaser CAN IP in FPGA Yes 40 kbit s to 1 Mbit s 1 us 20000 per channel Yes Yes Yes USB Hi Speed 9 40V Up to 3W Done by software Plug amp Play Windows XP or later For other operating systems contact Kvaser support 68 x 155 x 23 mm for body incl strain relief 150 g 320g including HD26 5DS9 Splitter 40 C to 85 C 40 C to 85 C 0 to 85 non condensing Table 8 Technical Specifications 4 4 CAN
19. oting soo 2 eho E RG Ee Yow e 4 Appendices 4 1 Definitions of LED states and colors 4 2 Start and stop of t programs 4 3 Technical Gala eas ee a rss ss ss ss EO ne 44 CAN connectors omer rss RE ee 4 5 CAN bus termination some oss ss sov rst 4 6 External trigger input 20 4 7 External trigger output a ooa 4 8 Updating the firmware aooaa a a a a 5 Disposal and Recycling Information 6 Legal acknowledgements 6 1 Usage warning soo see hue se bea ee ew sr 6 2 EC Regulatory Compliance 4 6 3 Patents Copyrights and Trademarks 7 Document Revision History cere Kvaser AB M lndal Sweden www kvaser com 3 26 O O O 0 NN 0 0 0 01 01 A Kvaser Memorator Pro 5xHS User s Guide 4 26 1 About this manual This manual is intended for Kvaser Memorator Pro 5xHS users This document contains a description of the hardware s properties and general instructions for connecting the device to a computer cere Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 5 26 2 Introduction This section will describe the functions and features of the Kvaser Memorator Pro 5xHS 2 1 Welcome to Kvaser Memorator Pro 5xHS Figure 1 Kvaser Memorator Pro 5xHS Kvaser Memorator Pro 5xHS is a small yet advanced portable CAN data logger that handles transmission and rec
20. t is connected only to CAN power If all the Traffic LEDs are showing the same pattern most likely including red there is some 1This should not normally happen 2The red Traffic LED indicating overrun will stay on until the device goes bus off cere Kvaser AB M lndal Sweden www kvaser com Kvaser Memorator Pro 5xHS User s Guide 14 26 problem and the Power LED will indicate what type of problem according to Table 6 on Page 14 When in operational mode the green Power LED shows what state the device is in armed active or stopped see Table 7 and the Traffic LEDs are showing the status of the CAN bus in the same way as in Interface mode see Table 4 on Page 13 Power LED Traffic LED Description Fast Waver Green Yellow All Fast Waver Yellow Red Firmware or Hardware error Fast Waver Green Yellow All Slow Waver Yellow Red Battery fault Yellow On All Slow Blink Red Disk full or Disk error Yellow On All Fast Blink Red Configuration file missing or corrupt Table 6 When all Traffic LEDs are showing the same pattern the Power LED indi cates the problems in Logger mode Power LED Description On Green Device Armed Fast Blink Green Logging active Slow Blink Green Logging stopped due to trigger Table 7 The green Power LED indicates that the device is in a valid state 4 1 3 Status of scripts There are by default no LED indications showing the state of a t program Instead the developer of a s
21. the Power LED is showing a steady green light the device is in Interface mode and working correctly When connected to the computer for the first time the Power LED will blink slowly in yellow until the driver is installed and it has received a USB configuration If the Power LED is showing yellow in the Interface mode for an extended period something is wrong see Table 3 on Page 13 When the device is connected to Kvaser Memorator Tools in Interface mode the LED will be showing any of the states shown in Table 5 The power should never be removed during disk activity or when A firmware update is in progress Power LED Traffic LED Description Slow Blink Yellow All off Waiting for USB configuration Slow Waver Green Yellow Slow Waver Yellow Red Firmware configuration error Table 3 Yellow Power LED shows problems in Interface mode Traffic LED Description Off Idle no CAN traffic Flash Yellow CAN message received or sent Flash Red Error frame received Fast Blink Red CAN channel is error passive On Red CAN overrun Table 4 Traffic LED shows CAN bus status in Interface mode and Logger mode Power LED Traffic LED Description Running Running Device is communicating with Memorator Tools On Green All Fast Blink Red Disk activity such as formatting or firmware update is in progress Table 5 LED indications when connected to Kvaser Memorator Tools 4 1 2 Logger mode The device is in Logger mode when i
Download Pdf Manuals
Related Search