User's Guide
Contents
1. GSW 5150 User s Guide 48 Port Fast Ethernet TP 3 Port Gigabit Ethernet TP SFP Ver 1 0 0 0803 REV 1 0 0 71035980 COPYRIGHT amp TRADEMARKS Specifications are subject to change without notice Level One is a registered trademark of Digital Data Communications Co Ltd Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from Digital Data Communications Co Ltd All rights reserved FCC STATEMENT The 48 Port Fast Ethernet TP 3 Port Gigabit Ethernet TP SFP Switch has been tested and found to comply with the limits for a class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the foll2. connection gt SFP LED The SFP LED indicates SFP module Link Active status The LED indicator will light solid green when the SFP port connected correctly It flashes green when data is being transmitted or received on the working connection 3 2 Rear Panel The rear panel of the GSW 5150 only features a power receptacle which is an AC power receptacle Connect the female of the power cord head here and the male head to the AC power outlet a Figure 3 2 GSW 5150 Switch Rear Panel sketch GSW 5150 48 Port Fast Ethernet 3 Port Gigabit Appendix A Specifications General Standards Data Transfer on Network Media 100Base T Cab 1000Base T UTP category 5 5e cable maximum 100m OOS Feta 1000Base LxX 62 5 um multi mode fiber Fone ie st bier TONT oan atin Safety amp Emissions FCC CE GSW 5150 48 Port Fast Ethernet 3 Port Gigabit Environmental and Physical Operating Temperature 0 C 40 C Storage Temperature 40 C 70 C Operating Humidity 10 90 non condensing Storage Humidity 5 95 non condensing 17 3 10 2 1 73 in 440 mmx260 mmx44mm
3. N wash EAEE tele ei eee oe ve ee 5 Chapter 3 Identifying External Component ccseseccesseeeeeeeeeeres 5 SAl Front Ramel iiss ieee art eee Net A ad eh ak 5 3 2 Rear Panel Appendix A Specifications eccceccecscseeseeeeeeeeeeeeeeeeeeeeeeseseeneeseeneaes 7 GSW 5150 48 Port Fast Ethernet 3 Port Gigabit Package Contents The following contents should be found in your box gt One Switch gt One power cord gt This User s Guide gt Rubber footpads for Desk mount gt Rack mount kit for installing the switch in a 19 inch rack AN Note If any of the above contents is damaged or missing please contact the retailer from whom you purchased the GSW 5150 Gigabit Ethernet Switch for assistance GSW 5150 48 Port Fast Ethernet 3 Port Gigabit Chapter 1 Introduction of the Product This chapter describes the features of the GSW 5150 Gigabit Ethernet Switch 1 1 Overview of the product The GSW 5150 Gigabit Ethernet Switch provides you with a high performance low cost easy to use seamless and standard upgrade to boost your old network to 1000Mbps Increase the speed of your network server and backbone connections make Gigabit connection to a server or uplink a network necessarily The GSW 5150 features a non blocking switching architecture that forwards and filters packets at full wire speed for maximum throughput MAC address auto learning and auto aging IEEE802 3x flow control for Full Dupl
4. ex mode and backpressure for Half Duplex mode It is compatible with all 10 100 and 1000Mbps Ethernet devices because it is standard based The GSW 5150 is plug and play and no configuration is required Auto MDI MDIX cable detection on all ports eliminate the need for crossover cable or Uplink port Each port can be used as general ports or Uplink ports and any port can be simply plugged into a server a hub a router or a switch using the straight cable or crossover cable Diagnostic LEDs which display link status and activity allowing you to quickly detect and correct problems on the network 1 2 Features gt Complies with IEEE802 3 IEEE802 3u IEEE802 3ab IEEE802 3z standards gt 48 10 100Mbps Auto Sense RJ45 ports supporting Auto MDI MDIX gt 2 10 100 1000Mbps Auto Sense RJ45 ports supporting Auto MDI MDIX GSW 5150 48 Port Fast Ethernet 3 Port Gigabit gt 1SFP Small Form Pluggable module interface gt Supports Auto MDI MDIX cable detection on all ports eliminate the need for crossover cable or Uplink port gt Non blocking switching architecture that forwards and filters packets at fullwire speed for maximum throughput gt Supports MAC address auto learning and auto aging gt Supports IEEE802 3x flow control for full duplex model and backpressure for half duplex transfer model gt LED indicators for monitoring power link activity speed gt Internal power supply Chapter 2 Installation 2 1 Mounting t
5. he Switch on a Desk Before place the Switch on a desk attach four rubber footpads to the flutes on the Switch bottom then lay the Switch on the desktop where can be have as much as 5kg placed on top A Note Make sure there is a grounded AC outlet within 1 5 meters and working well Make sure there is free space for radiating heat and air Make sure not to place anything to heavy on top of the switch GSW 5150 48 Port Fast Ethernet 3 Port Gigabit 2 2 Mounting the Switch in a Rack The dimension of GSW 5150 is designed according to the standard 19 rack mountable steel case of Electronic Industries Association Turn off all the equipment connected to the Switch before mounting it in the rack then rivet the two L brackets onto each side of the Switch fasten it with screws in the rack Figure 2 1 Rivet the L brackets onto the Switch Figure 2 2 Fasten the Switch in the rack GSW 5150 48 Port Fast Ethernet 3 Port Gigabit 2 3 Mounting the SFP module The front panel of the GSW 5150 consists of a SFP module which support The Hot Plug And Draw Should fixed the SFP into SFP pluggable when use the SFP module The switch could identify and Config the SFP module automatically 2 4 Power on GSW 5150 Switch is powered by AC power supply Powering on the Switch it will automatically initialize and its LED indicators should respond as follows 1 All of the LED indicators will flash momen
6. owing measures gt Reorient or relocate the receiving antenna gt Increase the separation between the equipment and receiver gt Connect the equipment into an outlet on a circuit different from that to which the receiver is connected gt Consult the dealer or an experienced radio TV technician for help EC DECLARATION OF CONFORMITY EUROPE In compliance with the EMC Directive 89 336 EEC Low Voltage Directive 73 23 EEC this product meets the requirements of the following standards gt EN55022 gt EN55024 gt EN60950 SAFETY NOTICES AN Caution Do not use this product near water for example in a wet basement or near a swimming pool Avoid using this product during an electrical storm There may be a remote risk of electric shock from lightning TABLE OF CONTENTS Package Content cc ceccescseccseeseseseeeseeeeseeeseseeeeeesneeseeeeseeeseseaeeeneeeeeneeaes 1 Chapter 1 Introduction of the Product c cscseccsesseeseeeeeeeeeeeeeeeeneee 2 1 1 Overview of the productes ccnc sss aiden aada a a a aaa 2 1 2 Features 0c en a al a ad 2 Chapter 2 Installation c ceccesseececeeeeeeeseeeeeceeeeeeeeeseeeaeseenseseeeeeeneeeneaes 3 2 1 Mounting the Switch on a Desk 2 2 Mounting the Switch in a RACK ccccceceeceeceececeeeceeeeeeeceaeeeceeeeesaeeaeeeseateeteeeaeee 2 3 Mounting the SFP Module eccceeseeeeecreeeeeeeceeeeaeeeeeaseeeesaeeatseeeseenetateneee 5 214 POWER O
7. tarily for one second which represent a resetting of the system 2 The power LED indicator will remain ON Chapter 3 Identifying External Components This Chapter describes the front panel rear panel and LED indicators of the Switch 3 1 Front Panel The front panel of the GSW 5150 consists of switch LED indicators 48 10 100Mbps RJ 45 ports 2 10 100 1000Mbps RJ 45 ports and 1 SFP module ie one magw5i60 ADPF Dhara TPs Mat a Praal TH Daten Figure 3 1 GSW 5150 Switch Front Panel sketch GSW 5150 48 Port Fast Ethernet 3 Port Gigabit gt LED indicators The LED indicators include Power Link Act 1000Mbps and 100Mbps LED indicators which are used for monitoring and pre troubleshooting of the Switch The following section shows the LED indicators for the Switch along with an explanation of each indicator gt Power LED This indicator will light solid red when the Switch powers up If the LED is not lit please check the power supply and connection gt 1000M LED The corresponding gigabit port LED indicator will light solid green when the gigabit port connected to a 10 100 1000Mbps device It flashes green when data is being transmitted or received on the working connection gt 100M LED The corresponding 100M port LED indicator will light solid green when the 10 100M port connected to a 100Mbps device It flashes green when data is being transmitted or received on the working
Download Pdf Manuals
Related Search