Tumble drying
Contents
1. For the consumption values given below the requirements are as follows Temperature of intake air 23 C Moisture content of intake air 55 Drying temperature Normal Heater output 2500W Program Load Spin speed Energy consumption Programme time rpm approx kWh approx min Auto extra dry Cotton linen 1 1 800 rpm 4 5 Auto dry Cotton linen 800 rpm 4 3 1 1 1 2 1 Crease resistant 1000 rpm 2 0 1 00 polyester cotton Auto normal dry Cotton linen 1 800 rpm 4 2 Crease resistant 1 2 1000 rpm 1 41 0 40 polyester cotton 11 Tumble drying gt Press the Start button Remaining drying time An estimate of the remaining drying time will be shown on the display a few minutes after the drying programme starts For example 1 35 means that it will take approximately 1 hour and 35 minutes for the load to dry The actual remaining time may be longer than the estimated time shown on the display The remaining time is then shown as 0 15 until the load is sufficiently dry You can stop the tumble dryer by pressing the Stop button or by opening the door In both cases the programme is stopped and starts from the beginning if restarted NOTE The programme will not be affected if you change the programme selector after the programme has started 12 Drying programme finished The text Done appears on the display when the programme is finished 6 Backlighting Two minutes after the drying progr2. SELECT A PROGRAM AND ANY OPTIONS Turn the program selector to the desired program PRESS THE START BUTTON DRYING PROGRAM FINISHED End appears on the display when the program is finished Clean the lint filter after each load Turn off the main power switch and close the door We reserve the right to make changes MIX Paper fr ibl om responsib e sources FSC www fsc cog FSC C114278 ce BE IM 502834 en 10 14
3. Care and cleaning Cleaning the lint filter 3 Use your hand or a soft cloth to remove the The lint filter must be cleaned after each load lint from all sides of the filter If necessary 1 Grasp the filter holder handle and pull it use a damp sponge and a small amount of towards you to open the lint filter washing up liquid to remove any deposits Dry the filter thoroughly with a towel 4 Close the lint filter before closing the door 2 Open the lint filter Use your thumb to press on the edge as illustrated and pull it out Care and cleaning Emptying the condensed water container If you have not connected the machine to a separate drain the condensed water container must be emptied after each load Remove the condensed water container empty out the water and replace the container If the condensed water container becomes full to overflowing the programme is interrupted and Over Flow appears on the display Empty the container and press the Start button to restart the programme For connection to a separate drain see the installation instructions in the set of documents Cleaning the outside of the machine Clean the outside of the machine and the programme panel with a mild cleaner Do not use solvents as these can damage the machine Do not hose down or spray the machine with water NOTE Do not allow dust to accumulate around the machi
4. be covered by the warranty In such cases the costs of repair shall be charged to the user Installation Positioning the tumble dryer The tumble dryer can be free standing or in a stack Remember that the tumble dryer produces heat and should therefore not be located in a room that is too small If the room is very small drying will take longer due to the limited quantity of air NOTE Do not install the machine in a room where there is a risk of frost occurring At temperatures around freezing point the machine may not be able to operate properly The room in which the appliance is installed should be adequately ventilated with temperature between 15 C and 25 C WARNING e Any electrical installation must be carried out by qualified professionals e The machine must not be installed behind a lockable door a sliding door or a door with hinges on the opposite side to those of the tumble dryer e The tumble dryer s plinth ventilation must not be blocked by a rug or the like TIP To improve ventilation leave the door to the room where the tumble dryer is located open Freestanding The tumble dryer can be positioned beside the washing machine An air gap of at least 5 mm must be left between the washing machine and the tumble dryer Stacking The tumble dryer can be placed on top of a washing machine Use the two foot cups found in the document bag included with the machine and the two tip guards attached
5. triggered The machine loses all power during a programme The overheating cut out shuts off the tumble dryer if the temperature is too high e g because dust is clogging the lint filter Clean the lint filter Check also that the condensed water container is not full and if necessary clean the condenser See the Care and cleaning chapter Wait until the machine has cooled then try Starting it If it still does not start Call the service division Drying takes too long Check that the lint filter is not blocked See the Care and cleaning chapter Empty the condensed water container and check that the condenser is not blocked See the Care and cleaning chapter Overly long drying times may also be due to the tumble dryer being located in a confined area or in a room that is too small causing the air to become too hot Make sure that the tumble dryer has access to more cold air open doors and or windows for example Error messages If Over Flow appears on the display the condensed water container is full Empty the container and restart the machine Read Drying takes too long in this chapter if Max program time appears on the display If Clean Lint Filter appears on the display clean the lint filter If Clean condenser appears on the display clean the condenser See the Care and cleaning chapter Call the service division if Thermistor fault appears on the display Press the Stop button to close any error me
6. watched to ensure they do not play with the machine A Safety e The machine must not be used for drying items that have been dry cleaned at home or fabrics that may contain residues of flammable liquids e The tumble dryer is not to be used if industrial chemicals have been used for cleaning e The tumble dryer is protected by an overheating cut out This shuts off the machine if the temperature gets too high e A float shuts off the machine in the event of a blockage in the condensed water hose or if there is a risk of the condensed water container overflowing WARNING A When the tumble dryer is operating the back of the tumble dryer will get very hot Leave the machine to cool completely before touching the back Installation See the section Installation Transport Winter storage If you need to move your machine or store it over the winter in unheated premises make sure that you drain the condensed water container beforehand Packing material Please sort waste materials in accordance with local guidelines Recycling This machine is manufactured and labelled for recycling In order to prevent personal injury the machine must be made inoperable after deciding to take it out of service Contact your local authority for information about where and how your machine should be correctly recycled Child safety General WARNING N Do not allow children to play with the tumble dryer e Ifthe door is opene
7. CMA Dear Imesa customer Welcome to the family of Imesa customers We hope that you will have many years of use from your new machine The machine has many features To make the most of its functions we recommend that you read the operating instructions before using the machine The operating instructions include information on how you can help protect the environment FS a Operating Instructions Tumble dryer Imesa ES7PEC WARNING Read the instructions before using the machine Contents Before using your machine for the first time Language selection Safety instructions Safety Transport Winter storage Packing material Recycling Child safety General Child safe start Activating deactivating Child safe start Description of the tumble dryer Advice and tips before you tumble dry Materials that can be tumble dried Materials that must not be tumble dried Static electricity Tumble drying Sort your fabrics Press the main power switch until the display lights Open the door load the items and then close the door Select the programme Press the Start button Drying programme finished Original Instructions 2 O 0 0 0 N O O OO 0 0 9 VG A A 10 12 12 Backlighting Condensed water Automatic emptying Settings You can carry out the following settings How to choose the settings Audible Volume Language Child safe Heater 2 Care and cleaning Cleaning the lint filter Emptying
8. amme finishes the backlighting on the display and option buttons enters energy saving mode Condensed water The condensed water container must be emptied after each load Remove the condensed water container empty out the water and replace the container If the condensed water container becomes full to overflowing the programme is interrupted and Over Flow appears on the display Empty the container and press the Start button to start a new programme TIP The condensed water is decalcified and can be used in steam irons Pour it through a coffee filter Automatic emptying For connection to a separate drain see the installation instructions in the set of documents NOTE e Clean the lint filter after each load e Drain the tank after each load WARNING N If the lint filter becomes clogged the machine s automatic overheating cut out may be triggered Clean the filter wait until the machine has cooled then try starting it If it still does not start Call the service division Once drying has finished Turn off the main power switch Remove the clothes and close the door to prevent small children from climbing into the machine Settings You can carry out the following settings e Audible Volume e Language e Child safe e Heater 2 How to choose the settings Do as follows to open the settings menu 1 Turn off the machine using the main power switch 2 Press the Stop button and switch on the mac
9. by pressing the Stop button for three seconds or by opening the door In both cases the programme is stopped and starts from the beginning if restarted If you do not want to restart the programme then immediately remove all laundry and spread it out to allow the heat to dissipate Tumble drying Below are step by step instructions to help you achieve the best possible tumble drying results You will achieve the most uniform drying results if the items are made of the same type of material Do up zips and buttons fasten belts sort the items and adjust the load and temperature 2 1 Sort your fabrics Press the main power switch until the display lights Open the door load the items and then close the door 3 Tumble drying A Select the programme Programme name Programme selector Start Stop Select a programme by turning the programme selector The selected programme is shown in the display window Guidelines as to what specific programmes can be used for The Auto extra dry Auto dry and Auto normal dry programmes have two temperature settings Normal temperature but also low temperature for more delicate items Auto extra dry Temperature normal This programme is for items that are particularly difficult to dry such as jeans with very thick seams Auto dry Temperature normal These programmes shut off the heat once the load is dry but before it is bone dry The Auto dry pro
10. d when a programme is running the garments may be very hot with a risk of burn injuries e Thetumble dryer does not start automatically when the door is closed if a child pulls the door shut from the inside for example Child safe start By activating the child safe start function you can prevent children from starting the tumble dryer or changing the current programme Activating deactivating Child safe start Do as follows to open the settings menu 1 Turn off the machine using the main power switch 2 Press the Stop button and switch on the machine with the main power switch Then press the Stop button 5 times within 10 seconds 3 Select the setting you want to change by turning the programme selector 4 Press the Stop button once 5 Change and save the setting as described below 6 Press the Start button to return to the programme menu You can activate the Child safe start option to prevent children from starting the machine 1 Turn the programme selector and choose Child safe On or Child safe Off 2 Press the Stop button once to save the setting You can temporarily deactivate Child safe start by pressing the Start and Stop buttons at the same time Child safe start will be deactivated for 3 minutes Description of the tumble dryer 5 Lint filter 1 Main power switch 6 Outer door 7 Condenser 2 Condensed water container 3 Panel 4 Type plate Advice and
11. e dryer you must not remove it just open it using a hammer and screwdriver 21 Installation Condensed water The machine is supplied as shown in Option 1 inset This means that the condensed water is pumped into the condensed water container which must be removed and emptied by hand Option 2 allows you to remove the small short hose from the nipple Attach the rubber hose supplied to the same nipple The water can then be pumped out into a sink or a floor drain 2a 22 Max 1000 mm Electrical installation If the machine is delivered from the factory with a plug attached it can be connected to an earthed wall socket Otherwise a permanent connection using a multipolar circuit breaker must be made by a qualified professional Connection on delivery e 230V 1 Phase 16A e 50Hz e Heat output 2500W e Use a type A residual current device Switch over The switchover must be performed by a qualified electrician See the section Settings Door hanging o oo o o o 06020 00009 099090 000093000290 o 000000050090 00 000008 50 o 00 gt 00 090 080 32000 00 090990 H 09420 oo 4 Locking hook 1 Hinge pins top and bottom 2 Cover plate 5 Hinges left right side 6 Plinth 3 Plastic plugs on the upper and lower edges 23 Door hanging You can choose whether the door is hung on the 7 Switch the catc
12. gramme shuts off the heat slightly later than Auto normal dry Use trial and error to find out what works best Auto normal dry Temperature normal These programmes shut off the heat once the load is dry but before it is bone dry The Auto dry programme shuts off the heat slightly later than Auto normal dry Use trial and error to find out what works best 10 Auto extra dry Bo low temperature Energy Save This programme is for items that are particularly difficult to dry such as jeans with very thick seams Auto dry Be low temperature Energy Save These programmes shut off the heat once the load is dry but before it is bone dry The Auto dry programme shuts off the heat slightly later than Auto normal dry Use trial and error to find out what works best Auto normal dry Bo low temperature Energy Save These programmes shut off the heat once the load is dry but before it is bone dry The Auto dry programme shuts off the heat slightly later than Auto normal dry Use trial and error to find out what works best Auto Iron dry This programme shuts off the heat once the load is just damp enough for ironing or pressing Tumble drying Programme chart Here we present the energy and time consumption of a few different programmes The table shows the effect of using different spin speeds when washing the load Consumption can vary depending on room temperature humidity load variations in the power supply and selected options
13. h magnetic lock and the right or the left cover plate First loosen the screw holding the catch magnetic lock in place Then use Follow these instructions a flat bladed screwdriver to remove the cover 1 Remove the plinth plate Refit the catch magnetic lock and the cover plate on the other side 2 Remove the hinge two screws 8 Reattach the inner part of the door with the screws 13 in total 3 Liftthe door up and remove it Support the 9 Move the plastic plugs on the upper and door at the same time lower edges of the door Use a flat bladed screwdriver to remove the plugs 4 Remove both door pins top and bottom Fit 10 Loosen the two screws holding the handle them on the other side of the machine Refit in place on the door Push out the two the hinge plastic plugs inside the screw holes on the other side of the door Use the two screws to attach the handle to the other side of the door and press the plastic plugs into the holes where the handle was previously fitted 11 Refit the door by loosening the hinge screws slightly affixing the door and closing it Retighten the hinges Replace the plinth 5 Loosen the screws 13 in total on the inside of the door 6 Loosen the inner part of the door pull down and lift out 24 Your notes 25 Your notes Your notes 27 QUICK GUIDE TURN ON THE MAIN POWER SWITCH Load the garments Close the door
14. hine with the main power switch Then press the Stop button 5 times within 10 seconds 3 Select the setting you want to change by turning the programme selector 4 Press the Stop button once 5 Change and save the setting as described below 6 Press the Start button to return to the programme menu Audible Volume 1 Turn the programme selector and choose Buzzer On or Buzzer Off to set whether the tumble dryer should audibly indicate that the programme is finished or that an error has occurred 2 Press the Stop button once to save the setting Language 1 Turn the programme selector to choose from US English English Svenska Dansk Norsk Suomi Francais Deutsch Italiano Espanol Pycckun Nederlands 2 Press the Stop button once to save the setting Child safe You can activate the Child safe start option to prevent children from starting the machine 1 Turn the programme selector and choose Child safe On or Child safe Off 2 Press the Stop button once to save the setting You can temporarily deactivate Child safe start by pressing the Start and Stop buttons at the same time Child safe start will be deactivated for 3 minutes Heater 2 1 Turn the programme selector and choose Heater 2 On 2500W 10A or Heater 2 Off 1950W 10A to increase or decrease the heat output 2 Press the Stop button once to save the setting NOTE The switchover must be performed by a qualified electrician
15. ne Keep the area around the tumble dryer clean and cool dust heat and moisture prolong drying times Care and cleaning Cleaning the condenser The condenser should be cleaned at least three times a year If you have pets the condenser must be cleaned more frequently 1 Turn off the tumble dryer with the main power switch and open the outer door 2 Remove the plinth 3 Open the condenser panel by turning the two knobs a R 000000000000 y 4 Remove the condenser and rinse the ribs clean such as with a hand held shower Do not poke around in the rib gaps as you may damage the condenser Do not use pointed metal objects when cleaning 16 NOTE Do not clean the condenser in a dishwasher 5 Wipe any lint from the channel in front of the condenser and inside the condenser compartment Use a cotton bud or similar item to remove any lint from the drain hole at the front edge of the compartment NOTE It is quite normal for water to collect in the channel in front of the condenser 6 Replace the condenser with the handle facing down as illustrated 7 Reattach the plinth Troubleshooting The machine will not start Check that the door is properly closed that the main power switch is on that the plug is connected that the main fuses have not blown that the overheating cut out has not been
16. oads Safety instructions Read the operating instructions and keep them in a safe place e Electrical installation if required should be carried out by a qualified electrician e The machine should only be used for tumble drying as described in these instructions e Repairs and maintenance relating to safety or performance must be carried out by a qualified professional e Damaged mains cables must only be replaced by a qualified electrician e Sufficient ventilation is required to prevent smoke from open fires or fumes from equipment burning other fuels being sucked into the room when the tumble dryer is running e Do not dry dirty laundry in the tumble dryer e Items that are stained with e g cooking oil acetone alcohol petrol kerosene stain remover turpentine wax and wax remover should be washed in hot water with extra detergent before they go in the tumbler dryer e Items such as foam rubber latex plastic waterproof textiles rubber coated items and clothes and foam rubber filled cushions must not be dried in the tumbler dryer e Fabric softener or similar products should be used as per the recommendations of the detergent manufacturer e The machine is not designed to be used by persons even children that are physically or mentally handicapped or lack experience and knowledge Such persons must receive instruction in how to use the machine from the person responsible for their safety e Children must be
17. ssages Technical information Technical data Height Width Depth Weight net Cylinder volume Max drying capacity Speed Rated power Drum material Outer casing material Setup Standard tests Europe Drying performance Energy declaration Test method for noise measurement 18 845 mm 595 mm 585 mm 44 kg 1121 7 kg 50 55 rpm See type plate Stainless steel Powder coated and hot galvanized sheet steel or stainless steel Stacking or freestanding EN 611 21 95 13 EEC Auto normal dry 7 kg cotton EN 611 21 95 13 EEC Auto normal dry 7 kg cotton IEC 60 704 2 6 Service Before contacting the service division See the Troubleshooting and Care and cleaning chapters to see whether you can rectify the problem If you need to contact the service division make sure that you know the model designation type designation and serial number The model designation 1 can be found on the first page of the operating instructions and on the machine panel The type designation 2 and serial number 3 can be found on the type plate which is found on the front of the tumble dryer inside the outer door NOTE Only authorised spare parts shall be used in the event of failure 0 0 60 00 0 0 0 OOOO0000000 oo0oo0o TYPE NOTE Repair or any warranty claim resulting from incorrect connection or use of the dryer shall not
18. the condensed water container Cleaning the outside of the machine Cleaning the condenser Troubleshooting The machine will not start The machine loses all power during a programme Drying takes too long Error messages Technical information Technical data Standard tests 12 12 12 13 13 13 13 13 13 13 14 14 15 15 16 17 17 17 ie 17 18 18 18 Contents Service Before contacting the service division Installation Positioning the tumble dryer Condensed water Electrical installation Door hanging Follow these instructions Quick guide 19 19 20 20 22 22 23 24 28 Before using your machine for the first time Language selection You will be prompted to select the display language when you have connected your machine and start it for the first time Do as follows 1 Turn the programme selector to choose from US English English Svenska Dansk Norsk Suomi Francais Deutsch Italiano Espanol Pycckun Nederlands 2 Press Stop to save the setting Laundry labels Certain materials are not suitable for tumble drying Always check and follow the instructions on each item s laundry label You can find more information in the Advice and tips before you tumble dry chapter NOTE When starting the tumble dryer for the first time or after a long period without use you may notice a slight thumping noise This noise is completely normal and will disappear after a few l
19. tips before you tumble dry Here are some tips that may help you before you begin tumble drying Have the clothes been spun Items to be tumble dried should be spun at 1000 rpm or faster Higher spin speeds save energy and reduce drying time Materials that can be tumble dried This symbol means that the material is suitable for tumble drying Fabrics best suited to tumble drying are cotton fabrics terry cloth and synthetic fibres Garments will be softer and lighter when tumbled than when hung out to dry NOTE The tumble dryer does not cause any significant wear on fabrics The lint that collects in the lint filter consists of dust and fibre residues formed when the items are used Materials that must not be tumble dried 5 This symbol means that the material is not suitable for tumble drying Certain materials may melt or become a fire hazard if exposed to heat and others can lose their shape or shrink And do not tumble dry e materials labelled Do not dry near heat e garments that have been dry cleaned at home e plastic foam e fibreglass material e wool must not be tumble dried because of the risk of felting Static electricity To reduce the risk of static electricity in the laundry after tumble drying you can e Use fabric softener when washing e Wait five minutes after the drying program ends before opening the door and removing the laundry from the dryer NOTE You can stop the tumble dryer
20. to the bottom left corner of the back of the machine 20 How to assemble the stack 1 Remove the two tip guards from the back of the tumble dryer Replace the screws that held the tip guards in place 2 Undo the two screws indicated on the back of the washing machine 3 Secure the anti tilt device using the screws as shown in the picture Installation 4 Attach the plastic cups for fixing the tumble 7 Push the tumble dryer in under the metal dryer s front feet to the washing machine s brackets At the same time keep the front top cover This is essential as only when the edge raised by 10 mm to 20 mm tumble dryer s feet are resting in the plastic cups can you be sure that the tumble dryer is correctly positioned on the washing machine Break off tag A on the cup fitted on the right hand side and tag B on the cup fitted on the left hand side Then remove the paper from the self adhesive surface under the plastic cups Fr 8 Lower the tumble dryer s front feet into the A plastic cups and adjust the tumble dryer to ensure it is level 5 Fitthe plastic cups so that the tags marked with arrows are against the front edge or side edge of the cover and press them firmly onto the cover Then break off the remaining tags nn Adjusting the feet Screw the feet in or out so that the tumble dryer is both stable and level Y 6 Push out the knock out hole on the back of the tumbl
Download Pdf Manuals
Related Search