The user manual for the series of SZ02 ZigBee Data
Contents
1. 2k 50mA SZ02 200 160mA SZ02 800 250mA SZ02 2K RS232 RS485 USB NET Glue stick antenna or suction cup antenna APY MR AS BYR WIRELESS SOLUTIONS The user manual for SZ02 ZigBee Data Communication Device 2 Interfaces In order to satisfy user friendly installation for clients there are RS232 RS485 RS422 USB or Net to be chosen 2 1 The bottom interfaces 1 RS232 interface the standard RS232 interface is DB9 The pins are as follows 2 gt TX 3 gt RX 5 gt GND The standard RS232 interface DBI 2 gt TX 3 gt RX 5 gt GND JL RS232 female 2 RS485 interface It is the standard RS485 interface the wires connect as follows A gt 485A B gt 485B Y gt 485Y Z gt 485Z the negative of power 485A 422Z The positive of power A85A 4A22Y Notes End user can use either DC1 or DC2 as power supply they are just different at the wire connection BY IFS BL BR WIRELESS SOLUTIONS The user manual for SZ02 ZigBee Data Communication Device 3 USB interface The standard USB B interface is convenient to link computer or IPC USB B interface 4 The standard NET interface The standard Ethernet interface 2 2 The upside interfaces There are 4 LED lights on the upside of the module to indicator the module s operating conditions SMA antenna interface Press CFG for 3 seconds to enter configuration mode SH IFS BL BR WIRELESS SOLUTIONS The user manual for2. 2 ZigBee Data Communication Device 4 Network ID setting NET_ID Notes 0000 FFFF The NET_ID must be set to be same in the same network 5 Channel setting Frequency Channels 2 405GHz 2 410GHz 2 415GHzZz 2 420GHz 2 425GHz 2 430GHz 2 435GHz Recommend to use channel 4 9 E or F 2 440GHz to avoid WIFI interference The channel 2 445GHz should be set the same in the same 2 450GHz network 2 455GHz 2 460GHz 2 465GHz 2 470GHz 2 475GHz 2 480GHz MMmHMoaAawWwrPrvoaAnauntwonr O 6 Data type Data_Type ASCII Can be chosen according to your need HEX 7 TX_Type setting TX_Type Configuration Notes Broadcast Destination address not required es WIRELESS SOLUTIONS The user manual for SZ02 ZigBee Data Communication Device Under mater slave mode Adding the destination node s address when the coordinator sends data to the non coordinator Non coordinators defaultly Destination address is the two byte MAC Mater slave send to the coordinator with not address this address will be added in requiring the destination address front of the data packet Adding the destination address in front of Point point Se ee data packet when Sending data 8 Baud Rate 1200 115200 can be optional according to your need 9 Data Parity setting Data_Parity None Even According to your requirement to choose the suitable parity Odd 10 Data Bit Settin
3. 5 USB or NET convert Strong wireless features support Multi hop Long distance 2000m at sight Strong anti jamming ISM Industrial Scientific amp Medical 2 4 GHz frequency band Flexible serial port rate Baud Rate can be set from 1200 to 115200 Transmit mode broadcast or destination address transmission Node type coordinator router or end device can be set Strong self organizing network star tree train or mesh Channels 16 Direct Sequence Channels 65535 PAN ID to be selected c WIRELESS SOLUTIONS 1 4 Specifications Device Distance 200M 800M The user manual for SZ02 ZigBee Data Communication Device Shell 5V 24V L Aluminum Interface Power supply RS232 RS485 RS422 USB NET optional Such as SZ02 2K RS485 L it means SZ02 ZigBee Data Communication Device transmission distance 2000M at sight RS485 interface Aluminum shell 1 5 Technical Parameter Performance Distance at sight range Operating frequency band Modulation Wireless channels Channel detection Network topology Network capacity The maximal data packet Transmission type Baud rate Supply voltage Receiver sensitivity Transmit power output The peak current Data Interface Antenna Technical Parameter SZ02 200 200M SZ02 800 800M SZ02 2K 2000M 1200 115200bps optional DC 5V 24V 92dBm SZ02 200 92dBm SZ02 800 105dBm SZ02 2K 3dBm SZ02 200 18dBm SZ02 800 25dBm SZ02
4. Device should be installed in anti static environment the antenna should be kept away from the metal objects 8 Technical support Shanghai Shuncom Electronic Technology Co Ltd Add 4 502 No 289 Bisheng Road Zhangjiang High Tech Park Shanghai China Tel 86 021 33933988 78 68 58 28 18 Fax 021 33933988 6808 Email 6822 shuncom com 6835 shuncom com Http www shuncom com
5. SZ02 ZigBee Data Communication Device 3 Accessories 3 1 Antennas Operating Frequency band ISM 2 4 GHz 2405M 2485M Interface type SMA male Antenna type Glue stick antenna Suction cup antenna Fiberglass antenna Accessory The extended cable Frequency band 2 4G Gain 5dBi Frequency band 2 4G Standing wave 1 5 Gain 1dBi Connector SMA male 3 Standing wave 1 5 Enea Long glue stick antenna length 21CM Connector SMA male Short glue stick antenna length 11CM Glue stick antenna Suction cup antenna Frequency band 2 4G Gain 8dBi Standing wave 1 5 Interface SMA Fiberglass antenna The extended cable Application used to extend antenna out of box Frequency band 2 4G Length 1M 2M 3M optional Notes The extended cable and the Suction cup antenna should not be longer than 3 meters The suitable length is within 1m Because the longer cable length the shorter transmission distance you will get 3 2 Power supply We use standard DC12V as our power supply the device also works under DC5V 24V Warning be aware that mis connect the positive and the negative of power will cause the device damage 4 Configuration 4 1 Connecting to the computer Please make sure the wire connection is correct before connecting to computer especially the 485 wires Meanwhile make sure the power supply is stable eS o Bb llth Ft FL Fz WIRELESS SOLUTIONS The user manual for SZ02 ZigBee Data Co
6. designed to operate within the ZigBee protocol and support the unique needs of low cost low power wireless sensor networks The device requires minimal power and provides reliable delivery of data between remote devices It has the features of long distance communication strong anti jamming capability and flexible network SZ02 ZigBee Data Communication Device has the serial ports of RS232 RS485 or USB It can realize point to point point to multipoint star or mesh network to transmit data SZ02 ZigBee Data Communication Device defines three different device types coordinator router and end device A coordinator can select a channel and PAN ID to start the network A router can assist in routing data The end_device always transmit and receive RF data through its parent cannot route data But the hardware is the same to them what you need to do is entering into the computer hyper terminal to set them as the coordinator the router or the end_device accordingly 1 1 Appearance HPEH Mit ee WIRELESS BOLUTIINE WIRELESS SOLUTION Wa cat of ek le SS WIRELESS BLT 1 USB Net SERRE WIRELESS SOLUTIONS The user manual for SZ02 ZigBee Data Communication Device 1 2 Dimensions MBL FF BS HR WIRELESS SOLUTIONS Width 8imm Height 25mm Installation port diameter Smm Long antenna 210mm Installation port spacing 7imm short antenna 110mm 1 3 Key features Communication serial ports of RS232 RS48
7. ected devices 5 2 Several typical configuration methods 1 Transparent transmission The coordinator is set as broadcast The router or end_device are set as mater slave or broadcast Other parameters please refer to page 12 configuration 2 Destination address transmission 1 Mater slave mode The coordinator router and end_device are set as master slave mode Other parameters please refer to page 12 configuration It is required to add destination address when the coordinator sends data to the non coordinators Non coordinators defaultly sent to the coordinator with not requiring destination address 2 Point point mode In this mode only two devices are allowed to communicate Destination address must be added in front of the data package when sending data e o WIRELESS SOLUTIONS The user manual for SZ02 ZigBee Data Communication Device 6 Running description 6 1 Indicator lights There are four lights to indicate the operation situations of the SZ02 device Indicator lights Indicate status Notes Not run power off or system failure For the coordinator the net light is always set to be on For the non coordinator the net light means successfully in the network System failure or enter a special state Power supply ok 6 2 How to connect the devices 1 It will need to connect to PC when SZ02 is set to be coordinator 2 If SZ02 used as router it only requires DC power supply then data will be tra
8. eeueeeeeceueeeeeesuceeeneeeeeneneess 9 Frequently used COnfiguration ccccccssecsesseseeessessesssseessesseessessesserssees 12 5 1 The tips for the Configuration ccccceccccceeeeececeeeseceeeeeceeeceeeeeueeeeeeeueeeeeesauceeeeeeeeeeeeeesneass 12 5 2 Several typical configuration methods cccssccccccceeecccecceeeececceeeececeeneeeceeseuseeeensenaeees 12 1 Transparent transmiSSiOn ccccccccceeeccccceececceeeeececeuceceennacececeuseeeennaceeeeneaseeensausess 12 2 Destination address tranSMiSSiOn ccccccccccccccccecccececeeeeececeeeneeeeeaeeeesdeeeeeceeeeeeeeeenanes 12 Running COS CPD UN OM osigiccctiecs occiictopctcednvataxicteiacini ices acid cee eaeeeiees 13 6 1 Indicator lights c cccccecceeeceeeceeceeeceeceeeeeeeauecaueeaueaeeeaesaeueaeeeaueauesaessueeauesaesaaesaeesaeenaees 13 6 2 How to connect the CC COS ae eect cten es aeeceteeel anaa NEn aui ENTANA 13 6 3 Fault CeSCriptiOn ccccccecececcececececaceceneaceceneaeacseeneneasenentaneneneneaneneaeansneneananenes 14 NOLES ree E E awa ey E E 14 Technical support sseesssesssessenessrnssenrnrrnsnrnnsrnnnnrnnsnnnnsrnnnnnnnsrnnnnrnnsnnnnnnnnnnnnnnnnn n 14 AN ING FS BY ER WIRELESS SOLUTIONS The user manual for SZ02 ZigBee Data Communication Device 1 Overview of the SZ02 ZigBee Data Communication Device Shuncom SZ02 ZigBee Wireless Data Communication Device is ZigBee Advanced Module which is integrated with zigbee 2 4G RF modem and MCU It is
9. g ELEM syim cele mets parity stop bit 7 1 1 8 0 1 Choose the data bit setting based on the selection of Data parity setting 8 1 1 8 0 2 11 Data source address Src_Add Not output HEX Generally default setting No Output ASCII SH IAS BL Be WIRELESS SOLUTIONS The user manual for SZ02 ZigBee Data Communication Device 12 Default settings SHUNCOM BEE CONFIG HAC Addr H 7F1A Node Name SHUNCOM Node Type Router Net_Type Star Net ID H FF Channel OF Data lype HEA TH_Ivpe Broadcast Baud Rate 9600 Parity None Data Bit 8 1 SRC Addr NOT OUTPUT select To Config 1 HAC Addr 2 Node name 3 Node Ilype 4 amp Net_Ilype 2 Net ID G Channel Data_Type TK_Dst 9 Baud _Rate A Parity E Uata Bit U Reset E Show All F Src_Add SHUNCOM gt Notes The module will be out of the configuration mode when there is no more operation within 60 seconds All the settings will stay unchanged 5 Frequently used configuration 5 1 The tips for the configuration 1 The coordinator s address is 0000 The address of the non coordinators router and end_device can be set optionally from 0001 to FFFE but the routers addresses must be different in the same network or else they cannot communicate 2 Each network is defined with a unique channel and PAN ID The channel and the PAN ID must be the same in the unique network And the baud rate parity data bit should be consistent with the conn
10. mmunication Device 4 2 Entering the computer hyper terminal 1 Open the computer hyper terminal Star programs Accessories communications Hyper Terminal choose right serial port and the configuration is Baud rate 38400 Data Bit 8 parity NONE Stop Bit 1 Flow NONE 2 Power on 3 Press CFG for 3 seconds 4 Alarm light and run light flash at the same time 5 Device is on configuration mode 4 3 Configuration parameters 1 Address setting configuration It cannot have the same MAC_ADDR 0000 FFFE address in the same network the coordinator address must be 0000 Notes Every ZigBee Device has the unique mac address it is not allowed to share the same address within the same network We use two bytes to define the MAC address 2 Node type setting Node Name Description PAN_Coord It is the coordinator which can select a channel and PAN ID to start the network Router Not only assist in routing data but also having the functions of end_device End_Device Only send data of itself and receive data from the coordinator 3 Network Net_Type Mesh ane Mesh star and line networks are the master slave networks They must have a coordinator All devices within the same network must set the same type of network Line Peer Peer to peer type network does not need coordinator Notes In the same network the Net_ type must be the same f WIRELESS SOLUTIONS The user manual for SZ0
11. nsmitted 3 The end_devices connect to user devices The end_device also can be set as the router which not only can transmit the data of itself but also have the router functions 232 USB Net interface connection by wiring _ a SZ02 Coordinator s zigbee wireless communication Ha Ti T a a a SZ02 Router Zigbee wireless communication 232 USB RS485 interface a connection by wiring Lo ae User device SZ02 End_device e 136 WIRELESS SOLUTIONS The user manual for SZ02 ZigBee Data Communication Device 6 3 Description of the fault Symptom Solution to the problem Run net alarm power LED light off Check the power supply Run net alarm power LED light on Maybe the main chip burn out please contact your supplier SJiite pide ilela Maybe power supply is too high power off device to check connection eV Vileleeeyivitsaacediva Please check the configuration parameters to make sure channel and PAN_ID are the network same Check if device is in configuration mode which you can tell from indicate LEDs power LED always on RUN and Alarm LEDs are flashing at the same time If not check wire connection and serial port setting Cannot get into con figuration mode 7 Notes 1 Power supply is under DC5V 24V 2 SZ02 Device is not waterproof 3 The anode and cathode of power do not reversed otherwise it will cause the device damage 4 The SZ02
12. www cablematic com The user manual for ZigBee Data Communication Device BY IFS BL BR WIRELESS SOLUTIONS The user manual for SZ02 ZigBee Data Communication Device Contents Overview of the SZ02 ZigBee Data Communication Device 00 3 LADO AN ected pected cecee E E E E E E 3 DZ DISS VOI een E E a e E ES 4 1 3 Key Features cccccceeceeceecceccecceccecceceeceecaecaecaecaecaesecsecsecsecsecsecseenesnesnesnecnesnesneseeseeeaeeaes 4 1 4 SOU 1 OUI oi ca cerarccasterarsodacs seen spcintenare esteatoustutsoinamanswindunossdaeeuunnent seen towensanesenebeevesteassaenes 5 1 5 Technical Parameter cccccccccccceeeeececceeeceeceeeeeeeseceueeeueeeeeeeeueseeeeeeneuseeeeeeneeaseeeeeenaseeness 5 ge TNS ECCS e tet ois erro E A 6 2 1 The potom Inora Sioa ee ai eiea 6 2 2 The upside interfaces icccccccceccccceeceecceececeeeeuceceeeeeeeeeeeeeaueeseueaueeeaueesaeeaaeessaeeeanesaneesanees 7 bP COS SON LS e eE EE EEEE GEGE 8 3 1 ANtON aS cecceceeceeceeceeceuceuceceeeeeueeueueeeeaesaesaueeeseusauseuseeseeaeseeseuseeseeseuseuseuseuseuseeaeeaeeass 8 S OVC SUNY parvo oe va setae ears tins anionic ae cared EEE E E 8 me Oro 04 00 a Le 00 eee ee eee ee ne eee 8 4 1 Connecting to the Computer vasanai faa ae ear eee ee eee ene caer ee 8 4 2 Entering into computer hyper terminal cccccccccsseseecceeceeeeeeeeceeeeeeeeeeeeeeaneeeeeeesesaueneeeeeeees 9 4 3 Configuration Parameter cccccccccceeecccececcceeecceeececececeeceeeeaueeenenee
Download Pdf Manuals
Related Search