INSTALLATION MANUAL
Contents
1. Sub power switch A21DIXC028CA E 5 lll Installation procedure C7000 C 7000P C 6000 C 70hc 1 Connect the V IF cable connector to the machine connector A21DIXC026CA 2 Connect the other end of the V IF cable to the oa of the image controller V IF cable connector A21DIXC025CA 3 Remove the protective sticker from the main power switch on the back of the image controller pn su i Ma 8 ie A21DIXC027CB E 6 4 Connect the power cord to the back of the image aoa my j i r hT E 7 ey l A i re il j FN f A21 DIXC023CA 5 Connect the network cable to the upper side of the LAN port on the back of the image controller Note Do not connect the cable to the lower side of the LAN port A21DIXC019CA 6 Plug the machine power cord into the wall outlet and then turn on the machine 7 Turn ON the main power switch on the rear side of the IC 306 and then turn ON the sub power switch of it Note Make sure the machine is on before you turn on the image controller lV Network setting Procedure Common operation LED Both the Controller NIC outside and the Machine NIC inside have two LEDs LED1 and LED2 each of which represent the following conditions LED 1 top Displays communication speed Machine NIC Controller NIC Orange 100Mbps Orange 1Gbps OFF 10M 1 Gbps Green 100Mbps OFF 10Mbps LED 2 bottom Displays th2. the message 80C KM is not dis 3 Display the Dongle Info list and check the played on the screen and then touch the OK number of uses Then touch the OK button button Number of Uses should be 1 of Uses 1 fe Option s0C KM enablement Dongle Info Enabled option FreeForm Server Info A21DIXC034CA A21DIXC033CA E 2 7 To enable printing on C8000 1 Select Enable option s Server Dongle A21DIXC010CA 2 Update will start automatically once Enable Option s is selected Enabling options Please wait To not shutdown or reset server or remove dongle A21DIXC011CA 3 When update is complete check that the mes sage Installed is displayed on the screen and press the OK soc KM enablement dongle mstallea _ Enable optionis A21DIXC035CA 8 To verify the installation is completed successfully 1 Select Server Info Dongle Info Enable option s Exit amp Reboot A21DIXCO004CA 2 Press the V button on the lower left of the screen to display the Enable option list Enabled option FreeForm 0C KM Server Info A21DIXC036CA Verify that the message 80C KM is displayed on the screen and press the OK button 3 FreeForm 80C EM ial enablement rg le A21DIXC037CA 9 To complete installation 6 Press Shut Down System to turn OFF the 1 Press Exit amp Reboot main power sw
3. F lery P RO 80 80C KM Image Controller INSTALLATION MANUAL Applied Machine C8000 C7000 C7000P C6000 C70hc l Contents ll Installation procedure C8000 Note The following procedures are only for C8000 Conduct the common procedures on the page 7 as well Procedure before installation 1 Remove the protective sticker from the main power switch on the back of the image controller D ao Protective sticker e Eee jp p i he i ma P A21DIXC027CB 2 Connect the power cord to the back of the image controller License Agreements accompanying this pa A21DIXC023CA 45095015 3 Turn ON the main power switch and the sub power switch of the IC 306 and then insert the Fiery Option Utility CD Note Be sure to insert the Fiery Option Utility CD right after the panel lights up Sub power switch A21DIXC002CB 4 Check the screen display and press the OK button Note lf the message does not appear restart the controller while keeping the Fiery Option Utility CD in the con troller mrress OK to Contine A21DIXC003CA A21D955022 5 To check Server Info 6 To Verify Dongle Info 1 Select Server Info 1 Insert the dongle into the USB port Dongle Info Mminable option s Exit amp Reboot 2 Press the V button on the lower left of the A21DIXCOO7CA screen to display the Enabled option list 2 Select Dongle Info 3 Check that
4. e link state Lighting Network is connected Blinking Data transfer state OFF Network is disconnected Step Check that the network cable is connected to both the machine and the image controller On the touch panel touch MACHINE and then touch Controller hen there is DHCP server Web LCD is displayed on the operation panel Touch Setup Touch the Administrator Password Enter Fiery 1 as an administrator password and then touch the OK key and Login key 5 When changing any setting touch the Save changes key and reboot the controller When not changed touch the Cancel key When there is no DHCP server An error message Is displayed on the operation panel Touch the Enable Legacy LCD key The setting screen appears Check the details with the user Administrator and change the setting if necessary 3 The display returns to the Machine tab Touch the Controller key again Touch the Setup Touch the Password key Enter Fiery 1 as an administrator password and then touch the OK key 7 9 Check the details with the user Administrator and change the network settings 1 2 and 2 2 Enabled is recommended for the Web LCD setting of the network setting 2 2 Touch Back and OK to return to the Control ler menu When changing any setting touch the Apply Reboot key to reboot the controller The following three menus will appear e Server Setup e Net
5. itch Eject CD DVD IF Address Restart Server Shut Down System Server Info mlorgle Info e option s SERVER U 98Gl2 O A21DIXC020CB 2 Press the OK button Installation procedure 1 Connect the V IF cable connector to the machine connector A21DIXC039CA Select OK and Mait for CD to eject A21DIXC014CA 3 Please remove the Fiery Option Utility CD Once the CD is removed the controller will be restarted automatically 4 Remove the dongle from the controller 5 After restarting the controller press the button 2 Connect the other end of the V IF cable to the shown in the picture below back of the image controller A21DIXC024CA SERVER UJ98GIZY V IF cable connector A21DIXC025CA A21DIXC038CA E 4 3 Connect the network cable to the upper side of 6 Install the cord holdings the LAN port on the back of the image controller Note Note Only when the PF is connected Do not connect the cable to the lower side of the Connect to the ISi Case LAN port Network cable A1RGIXC038CA A21DIXC019CA 4 Plug the machine power cord into the wall outlet and then turn on the machine 5 Turn ON the main power switch on the rear side of the IC 306 and then turn ON the sub power switch of it Note Make sure the machine is on before you turn on the image controller La Cord holdings A1RGIXC041CA Main power switch m SS A
6. work Setup 1 2 e Network Setup 2 2 V Shut Down Procedure Common operation Note Always use the following procedures to turn the power OFF 1 Press any button shown below to access the Shut Down menu O seaver nxxx H 2 Select Shut Down System and press the line selection button as shown Eject CD DVD IP Address Restart server Shut Down System
Download Pdf Manuals
Related Search