Z1 PLUS IP65 DMX-512 LED CONTROLLER User Manual Rel 2.0
Contents
1. O A 2 Z1 PLUS IP65 IMPORTANT SAFETY INFORMATION Fire prevention Never locate the fixture on any flammable surface Minimum distance from flammable materials 10 cm Replace any blown or damaged fuses only with those of identical value Prevention from electric shock High voltage is present inside the unit Unplug the unit prior to performing any operation which involves touching the inside of the unit This equipment must be grounded do not connect to non grounded supplies The use of a thermal magnetic circuit breaker is recommended for each Z1 PLUS IP65 Use only AC supplies 90 260V 50 60Hz The unit should never be located in position exposed to rain or in areas of extreme humidity A good air ventilation is essential for proper equipment work Safety The external surface of the unit may exeed 50 C never handle the unit until at least 5 minutes have elapsed since the unit was turned off Never install the unit in an enclosed area lacking sufficient air flow The ambient temperature should not exeed 40 C and should not be lower than 10 C DESCRIPTION Z1 PLUS IP65 is a full range AC 90 260 V 50 60 Hz power supply unit dedicated specifically for use with DTS products featuring LED technology Z1 PLUS IP65 can control set ups of D T S LED products in various combinations Z1 PLUS IP65 can be used in Master or Slave mode ample networks of interconnected Z1 units can be created max 32 slave unit2. programs and macros SHUTTER Shutter level selectable by user as on DMX channel 1 Shutter Shutter level is active only for CU01 CU16 and Wh01 Wh16 Macros ESC Exit from Automatic Mode Menu 9 Z1 PLUS IP65 ES SPEE IS Down 00 ifs l Anbr Anbr l Pas ENTER IS SPEE ES Up Down 00 ge 280 ids TE ENTER Up Down ENTER KF ENTER Up Down ENTER ES 0 Z1 PLUS IP65 Ee Se TES OCA MENU Up Down ENTER ENTER REC MODE In DMX Recorder Mode it is possible to create and store the scenes of the ChPr by using an external DMX controller The unit must be setted to 10 channels MODE DMX Recorder Mode For the programming of ChPr by using a DMX controller besides the 10 channels necessary to control the unit a further 3 DMX channels are needed So that in RECORDER mode via DMX the unit will need 13 channels to be correctly programmed The three new DMX channels are DMX channel 11 SCENES channel From 0 10 no function r001 From 11 255 are displayed the programmable scenes max 16 scenes from M001 to M0016 DMX channel 12 EDIT channel From 0 19 no function From 20 234 the unit runs the configuration given by the received input DMX values With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene From 235 255 the unit runs the configuration given by the received input DMX va
3. 149 Mater 150 164 Macro 165 179 Yo Macero MET OO Macro dt Ro Y Macrold S 210 2235 Macro 226 239 Mater 240255 o gt Macrot 6 O 17 Z1 PLUS IP65 DMX CHANNEL 9 Parameter COLOUR MACROS F IS IS NNJE F IE SIS EHLE PLEASE CHECK PAGE 7 jam Move degrees a poo pp of NoFuncetion 1522 po Macro BY Macro 31 388 o o of MaeroZ 3946 pop of Maoh 47 54 pp Macros BA Macro6 BR Yoo yo Maero7 AB po pp Macros 79 866 poo Maco9 i 8794 Y pp Macro 95102 pp of oo Maeroll 103 110 Yo S Maerol2 amg Mae H9126 pop Macrod 127 134 Mero O 135 142 po Macrol6 143150 ooo RainbowSpeed1 Sec 151 158 op Rainbow Speed 2 5 Sec 159 166 O Rainbow Speed 3 10 Sec 167 174 Rainbow Speed 4 20 Sec 175 182 Rainbow Speed 5 30 Sec 183 190 po Ratinbow Speed 6 60 Sec 91 198 Rainbow Speed 7 120 Sec 199206 Rainbow Speed 8 180 Sec aora Random Speed 1 05 sec 215 222 Random Speed 2 1 See 223230 Random Speed 32 See 231 238 Random Speed 4 5 Sec 239246 Random Speed 5 10 Sec 247 288 Random Speed 6 30 Sec DMX CHANNEL Move LAME ramas range Mode Option Function Value degrees Parameter FUNCTIONS Recall Create and Store the Custom white 079 Custom White Recall Enable CH 6 for Custom white Recall 80 160 A Custom Wh
4. DTS Wall mounted DMX controller 0514L007 M4CH mode 5 DMX channels Dimmer RGBA RGBA mode 4 channels 1 DMX channel mode If you want to use the Z1 RGB in 6 channels mode select the 6 CH mode from the MODE menu and set the following addresses on the mixer To be used only with DTS Wall mounted DMX controller 0514L007 Projector 1 A001 If you want to select the next projector just add 8 Projector 2 A009 DTS Wall mounted DMX controller 0514L007 assign 8 DMX Projector 3 A017 channels per unit also if some channels are not used e A projector A041 If you want to use the Z1 PLS IP65 in 10 channels mode select the 10 CH mode from the MODE menu and set the following addresses on the mixer Projector I A001 Projector 2 A011 If you want to select the next projector just add 10 Projector 3 A021 nue A projector A051 Selelcting the DMX address 1 Press the UP DOWN key until you reach the required DMX address The numbers on the display will start to flash but the new DMX address hasn t yet been set 2 Press ENTER to confirm your selection The numbers on the display will stop flashing and the projector is now controlled by the new DMX address TIPS if you keep pushed the UP or DOWN keys the channels are calculated more quickly and you get a faster selection 7 Z1 PLUS IP65 DISPLAY FUNCTIONS a DP Digital Fonction Pi Panel ENTER DISPLAY FUNCTIONS The Z1 PLUS IP65 display panel shows
5. 218 Random Strobe Full 230 234 Red Yellow Cyan and Blue colour effects at variable speed 235 255 245 Open 23 Z1 PLUS IP65 LED UNITS WIRING CONNECTIONS M12 LED Female cable connector on board Z1 PLUS IP65 2 a ae 5 Pint 7 6 7 Pint M12 LED Male cable connector on board FOS 100 PLUS a FOS 100 PLUS ALL MODELS IMPORTANT The maximum number of FOS 100 Plus Led projector connectable to the Z1 PLUS IP65 Power supply is 1 pcs The Maximum distance between the Z1 PLUS IP65 and FOS 100 Plus all models should not exceed 100 meters NEVER CONNECT NOR DISCONNECT A LED UNIT WHEN THE POWER SUPPLY IS TURNED ON 24 Z1 PLUS IP65 LED UNITS WIRING CONNECTIONS M12 LED Female cable connector on board Z1 PLUS IP65 2 ee A 8 5 Pint 7 6 7 Pint M12 LED Male cable connector on board FOS 33 Plus M12 FEMALE Pin 4 M12 MALE5 i 6 y 7 Pin1 IMPORTANT The maximum number of FOS 33 Plus Led projector connectable to the Z1 PLUS IP65 Power supply IS 3 pcs The Maximum distance between the Z1 PLUS IP65 and the last FOS 33 Plus on the line should not exceed 100 meters NEVER CONNECT NOR DISCONNECT A LED UNIT WHEN THE POWER SUPPLY IS TURNED ON 25 Z1 PLUS IP65 LED UNITS WIRING CONNECTIONS M12 LED Female cable connector on board Z1 PLUS IP65 7 Pin M12 LED Male cable Pp connector on board HELIOS R HELIOS R A
6. Connection between the controller and the unit or between units must be carried out using a two pair screened g0 5 mm Ensure that the conductors do not touch each other Do not connect the cable ground to the DMX connector chassis The plug housing must be isolated Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first unit to the DMX IN plug of the second one In this way all the projectors are cascade connected CONTROLLER P S If the display showing the DMX address flashes then one of the following errors has occurred DMX signal not present DMX reception problem For Installations where long distance DMX cable connections are needed we suggest to use a DMX terminator The DMX terminator is a male DMX cable connector with a 120 ohm resistor Between pin 2 and 3 The DMX terminator must be plugged into the DMX out panel connector of the last unit connected to the DMX line DMX MALE CABLE CONNECTOR GND DATA DATA 120 OHM PLACE A 120 OHM RESISTOR BETWEEN PIN 2 AND 3 OF A MALE DMX CONNECTOR AND PLUG IT INTO THE DMX OUT PANEL CONNECTOR OF THE LAST UNIT CONNECTED TO THE DMX LINE 6 Z1 PLUS IP65 DMX ADDRESS Z1 PLUS IP65 can be used in seven different modes 10 DMX channels mode default 15 DMX channels mode Dimmer RGBW channels 16 bit 6 DMX channels mode Shutter Dimmer RGBA WALL mode 6 DMX channels for use with
7. LL MODELS IMPORTANT The maximum number of HELIOS R Led projector connectable to the 21 PLUS IP65 Power supply is 1 pcs The Maximum distance between the Z1 PLUS IP65 and HELIOS R should not exceed 100 meters NEVER CONNECT NOR DISCONNECT A LED UNIT WHEN THE POWER SUPPLY IS TURNED ON NOTES NOTES The information contained in this publication has been carefully prepared and checked However no responsibility will be taken for any errors All rights are reserved and this document cannot be copied photocopied or reproduced in part or completely without prior written consent from D T S D T S reserves the right to make any aesthetic functional or design modifications to any of its products without prior notice D T S assumes no responsibility for the use or application of the products or circuits described herein MADE IN ITALY The Lighting Company ISO 9001 2008 D T S quality system is certified to the ISO 9001 2008 standard D T S products are designed and manufactured at the D T S plants in italy 05171185 D T S Illuminazione s r l Via Fagnano Selve 10 12 14 47843 Misano Adriatico RN Italy Tel 39 0541 611131 Fax 39 0541 611111 info dts lighting it www dts lighting it
8. LS IR Dimmer RGBW channels 16 not yet implemented Upon bit AUX mode let you activate an external ES USE IS gt Custom mode enabled ON OFF control on IR connector me ENTER Let Down i not yet implemented not implemented on Z1 PLUS IP65 Ig OIL AUX MODE lt gt External ON OFF control on IR Up Down ML ENTER connector not implemented on z1 MACRO plus ip65 MACRO Function enable channel Standard mode enabled mapping macro rainbow effects Ig E A r STD default APRO me des mode enabled IES Rainbow effects on MACRO channel Is is Davin ae ENTER Default ENTER Z1 PLUS IP65 IF IF IF IF MENU Up Down ENTER Up Down LED RGBA Min Max Smooth Compression Sync and Boost level values settings Up Down a RGBA MINIMUM VALUES This menu allow to select the minimum levels for Red Green Blue and Amber Up Down a RGBA MAXIMUM VALUES This menu allow to select the maximum levels for Red Green Blue and Amber a These settings have priority on Master Dimmer Up Down SMOOTH VALUE This menu allow to select the value of the delay in milliseconds for RGBA and Dimmer channels reaction to DMX or Program variation Off 25 ms delay Fast response 20 250 ms delay Slow response a COMPRESSION This menu allow to select between Linear current output or quadratic current output for LEDs Default Linear Up Down SYNC This menu allow to adjust the PWM frequency value Hz
9. all the available functions Using these functions it is possible to change some of the parameters and add some functions Changing the D T S setting can vary the functions of the unit so that it does not respond to the DMX 512 signal used to control it Carefully follow the instructions below before carrying out any variations or selections NOTE the symbol IS shows which key has to be pushed to obtain the desired function Software version 5 09 IS IS IS IF FO A ADO MEN Up Down ENTER Up Down ES Ss Down AA postion ENTER REVERSE DISPLAY Reverses display s reading depending on os MITRA Posen I the mounting position on the ground or position eee suspended p Dawi DISPLAY STAND BY To turn off the display after 5 seconds Display gt or leave it always on always ON ENTER MENU Up Down ENTER Up Down DMX MODE IR 6 CHANNELS Up Down ENTER To select DMX mode 10 DMX channels mode default 15 DMX channels mode Dimmer RGBW channels 16 bit gt 1 CHANNEL IR 6 DMX channels mode Shutter Dimmer RGBA WALL mode 6 DMX channels for use with DTS Wall gt RGBA 4 CHANNELS Is mounted DMX controller 0514L007 M4CH mode 5 DMX channels Dimmer RGBA RGBA mode 4 channels 1 gt 6 CHANNELS gt DMX channel mode CUSTOM DMX mode let you set the IF MACH 5 CHANNELS I Dimmer RGBA parameters for Shutter Dimmer Red Green Blue Amber Ctc Macro and Function to the desired DMX channels IS 15 CHANNE
10. arameter AMBER Move E range Mode Option Function Value E E 0 255 Proportionalcolour Parameter WHITE Pre programmed White at diff color temperature DMX range Mode Option Function Value o 055 No Function 56 105 SS 4 Full Red Green Blue at Full 106 155 130 White DTS IF CHANNEL 10 FUNCTIONS CUSTOM WHITE RECALL Dmx range value 0 79 156 205 180 Custom White Recall 206 255 225 White CTC Channel 8 CTC enabled 256 color temp Correction Macros 2800 K 6500 K IF CHANNEL 10 FUNCTIONS CUSTOM WHITE CREATE Dmx range value 80 160 156 205 Custom White Create RGB levels selectable by DMX 206 255 White CTC Channel 8 CTC enabled 256 color temp Correction Macros 2800 K 6500 K 16 Z1 PLUS IP65 _DMX CHANNEL 8 Parameter CTC Color temperature correction Move LAS ronge range Mode Option Function Value degrees IF CHANNEL 7 White WHITE CTC Dmx range value 206 255 0 255 256 color temp Correction Macros 0 2800 K 128 4500 K 255 6500 IF CHANNEL 7 White NO FUNCTION Dmx range value 0 43 0 255 No Function y Parameter COLOUR MACROS F IF IS IS NAJE IS IF IS Q NAC IS IS St y PLEASE CHECK PAGE 7 Move DMX range range Mode Option Function Value O A 0 14 14 NoFunction Function AO O AOS OS A o 3044 O Mater 4559 O Mater 00 74 Mr BA Mtr 90 008 TT Maero6 105 119 Macro 120134 ff Macro 135
11. at the scene has been recorded It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene If ChPr is not closed by indicating the last scene Edit channel between 235 255 in playback mode all 16 scenes will be played through even if not programmed 14 Z1 PLUS IP65 10 CHANNELS MODE Default SHUTTER DIMMER RED GREEN BLUE AMBER WHITE Pre programmed whites at different colour temperatures CTC COLOURS MACRO FUNCTIONS SCUON AU RW N E pl E Parameter SHUTTER DMX range Mode Option Function Value Black out sa A Open 20 290 24 i Black out 30 119 Strobe at variable speed from slow to fast 3700ms 20ms 120 149 Pulse open at variable speed from slow to fast 42 6s 100ms 150 179 Pulse close at variable speed from slow to fast 42 6s 100ms 180 204 192 Random Strobe Master and RGB active 205 229 218 Random Strobe Full 230 234 Red Yellow Cyan and Blue colour effects at variable speed 235 255 245 Open DMX CHANNEL Parameter DIMMER DMX range Value DMX range Value 2 0355 Proportional colour 15 Z1 PLUS IP65 DMX CHANNEL ES Parameter GREEN Move NDS renge range Mode Option Function Value 0 255 Po Proportionalcolour DMX CHANNEL Parameter BLUE AE Move DMX range range Mode Option Function Value A eee 0255 Proportionalcolour DMX CHANNEL nasa JE P
12. c 50 60 Hz male connector DMX IN OUT Female Connector LED OUTPUT cable 30 cm lenght with M12 female cable connector DMX IN OUT Female Connector M12 LED output Female connector on board Z1 PLUS IP65 MAINS DMX IN OUT MALE CONNECTOR FEMALE CONNECTOR L CN ama 3 2 N DATA DATA Display 4 Z1 PLUS IP65 WIRING DIAGRAM Z1 PLUS IP65 is provided with an M12 female cable connector 30cm cable lenght M12 LED input M12 LED output M12 LEDS Male cable connector Female cable connector CONNECTOR PINOUT on board FOS on board Z1 PLUS IP65 TITAN HEAD 1 RED FC RGBA WHITE RA7 HEAD UNITS 2 RED FC RGBA WHITE FC RGBA WHITE FC RGBA WHITE FC RGBA WHITE 3 GREEN 4 GREEN 5 BLUE r 6 BLUE FC RGBA WHITE 7 Pini Pin1 7 6 7 AMBER RGBA WHITE 8 AMBER RGBA WHITE n I For application where IP65 rating is not necessary Z1 PLUS IP65 cabling connection can be done with a standard UTP TIA EIA 568 B2 category 5E cable The maximum distance between power supply and the last unit on the line should not exceed 100 meters For IP65 rating application D T S reccomed the use of a IP65 68 cable as the 8XAWG24 multipolar black outdoor cable IP68 D T S Code 0509C062 The maximum distance between power supply and the last unit on the line should not exceed 100 meters 5 Z1 PLUS IP65 DMX SIGNAL CONNECTION The unit operates using a digital DMX 512 signal
13. in order to reduce flickering in the process of your camera recordings Up Down BOOST DRIVING This menu allow to increase the LED s current from 350 mA to 500 mA ENTER ENTER ENTER Orme INIA ENTER gt gt Up Down Up Down Up Down Up Down Up Down Up Down Up Down Up Down Up Down ENTER Default 100 ENTER Default 0 RP ENTER Default 100 ISP ENTER Default 0 RRP ENTER Default 100 SP ENTER Default 0 RRP ENTER Default 100 SP ENTER Default 4 ENTER Off 25 ms Istant responce to DMX variation 20 250 ms Smooth response to DMX variation Linear Linear current output ENTER Quadratic Linear light ENTER output Range 610 Hz 10 KHz ENTER Default 610 Hz Boost mode activated MES ENTER Boost mode deactivated ars Whit BOOST active the LED s current is set to 500 mA 30 more gain Default Activated ES mE IS IS IS MENU Up Down ENTER ENTER Up Down AUTOMATIC MODE Automatic demo game without DMX controller ChPr Chase with 16 steps previously created in REC MODE Speed and Wait time selectable by user CUPr RGBA values selectable by user Rainbow rAIn Rainbow colours effect Speed time selectable by user CU01 CU16 Color Macros as on DMX channel 8 Macro WHITE MACROS 16 macros for White color from 2800 to 6500 K DIMMER Dimmer level selectable by user as on DMX channel 2 Dimmer Dimmer level is active for all the
14. iority on the slave units NB It is possible to run Ch Pr on the other units even though these do not have Ch Pr programmed You can do this by setting the units to 10 channels DMX and selecting DMX address A001 13 Z1 PLUS IP65 Rec mode It is possible to program your own game on the Z1 PLUS IP65 that will then run it in AUTO mode ChPr Each unit can have its own programmed game In REC mode the unit must be set to 10 channels mode To program the ChPr by using a DMX controller you need 3 more channels in addition to the 10 channels necessary to control the unit So that in RECORDER mode via DMX the unit will need 13 DMX channels to be correctly programmed The three new DMX channels are DMX channel 11 SCENES channel From 0 10 no function r001 From 11 255 are displayed the programmable scenes max 16 scenes from M001 to M0016 DMX channel 12 EDIT channel From 0 19 no function From 20 234 the unit runs the configuration given by the received input DMX values With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene From 235 255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene With the channel REC it is possible to record the selected scene as last scene DMX channel 13 RECORDING channel Records the set scene with a variation between O to 255 the display flashes indicating th
15. ite Create Enable CH 6 for Custom white Creation 161 2585 Custom White Store Store the Custom White created 18 Z1 PLUS IP65 6 CHANNELS MODE Shutter Dimmer RGBA SHUTTER DIMMER RED GREEN BLUE AMBER O UILLA LUNS E pee 1 Parameter SHUTTER DMX range Mode Option Function Value Black out a A ERE Open a a Black out 30 119 Strobe at variable speed from slow to fast 3700ms 20ms 120 149 Pulse open at variable speed from slow to fast 42 6s 100ms 150 179 Pulse close at variable speed from slow to fast 42 6s 100ms 180 204 192 Random Strobe Master and RGB active 205 229 218 Random Strobe Full 230 234 Red Yellow Cyan and Blue colour effects at variable speed 235 255 2458 Open DMX CHANNEL Parameter DIMMER DMX range Value DMX range Value 2 0355 Proportional colour 19 Z1 PLUS IP65 ae a DMX range Mode Option Function Value 0255 Proportional colour AS DMX range Mode Option Function Value 0255 o Proportional colour ES tn DMX range Mode Option Function Value 02585 Proportional colour 20 Z1 PLUS IP65 DMX PROTOCOL M4CH mode 5 DMX channels Dimmer RGBA DIMMER RED GREEN BLUE AMBER U UN re DMX CHANNEL Parameter DIMMER DMX range Value DMX range Value DMX range Value DMX range Value DMX CHANNEL xoia A Parameter AMBER DMX range Value 2 0355 Proportional colou
16. jectors with a DMX cable picture below A maximum quantity of 32 slave units can be connected to the same Master unit MASTER SLAVE 1 SLAVE 2 SLAVE 3 SLAVE 32 To activate Auto mode on the first unit use the menu to run through the different modes until AUTO appears on the display and press enter Now it is possible to choose between the different pre programmed games CUPr RAIn CU01 CU16 Wh01 Wh16 or ChPr which is user programmable through REC mode To confirm game activation press ENTER on the selected GAME CUPr RAIn CU01 CU16 Wh01 Wh16 The first unit that will work as a Master should be placed in Automatic mode AUTO the other units have to be placed in 10 channels DMX mode MODE 10 CH and the DMX address should be set at A001 For Raln rainbow game it is possible to select the speed for the colour changhing SPEE DIMMER function in AUTOMATIC MODE is active for all the programs SHUTTER function in AUTOMATIC MODE is active only for CU01 CU16 and Wh01 Wh16 macros ChPr MASTER SLAVE The first unit that will function as a Master must be set to Automatic mode AUTO the other units must be set to Slave mode SLAV selectable through the menu In this way all the Slave units will be synchronised with the master and running their own ChPr game On the master unit it is possible to vary the Speed time SPEE for the colour changhing and the Wait time UAIt between the steps Speed time and Wait time on the Master have pr
17. lues closing the sequence as last scene With the channel REC it is possible to record the selected scene as last scene DMX channel 13 RECORDING channel Records the set scene with a variation between O to 255 the display flashes indicating that the scene has been recorded It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene If ChPr is not closed by indicating the last scene Edit channel between 235 255 in playback mode all 16 scenes will be played through even if not programmed Be AS SL AU SUPE SS p Down ENTER ENTER Up Down SLAVE MODE Slave mode for ChPr program All slave units will be synchronised with master unit running their own Chpr program ENTER IS gt gt gt MENU Up Down ENTER Up Down INFRARED MODE NOTE Infrared remote control External infrared remote sensor By activating Ir MODE it will be needed possible to navigate trought the D T S Code 03 LA 016 unit functions by using the D T S Important IR function is not infrared remote control Implemented on Z1 PLUS IP65 D T S Code 0514L008 gt IR IS IT MENU Up Down ENTER Up Down FAN SPEED CONTROL Internal Fan Speed control selectable by user Range OFF 12 24 volt Default 18 Volt m 2 A m 7O ENTER Fan Speed Control Range OFF 12 24 volt Default 18 Volt a I ENTER Up Down ere MENU Up Down Leics I ES EMERGENCY Emergenc
18. r 21 Z1 PLUS IP65 DMX PROTOCOL RGBA mode 4 DMX channels 1 RED 2 GREEN 3 BLUE 4 AMBER a AAA DMX range Mode Option Function Value 2 0255 Proportional colour SA DMX range Mode Option Function Value 0255 Proportional colour AS DMX range Mode Option Function Value 0355 Proportional colour Value 0355 Proportional colour 22 Z1 PLUS IP65 DMX PROTOCOL WALL 6 CHANNELS MODE For use with DTS Wall mounted DMX controller 0514L007 IS IE IS ITS gt GREEN MEN Up Down ENTER Up Down O CHANNELS ENTER 1 2 RED 3 BLUE 4 DIMMER 5 NOT USED 6 SHUTTER DMX CHANNEL 1 Parameter GREEN DMX range Mode Option Function Value 0 255 Proportional colour DMX CHANNEL 2 Parameter RED DMX range Mode Option Function Value 0 255 gt op Proportional colour Parameter BLUE DMX range Mode Option Function Value Parameter DIMMER DMX range Value DMX CHANNEL 5 Parameter NOT USED DMX range Value DMX CHANNEL 6 Parameter SHUTTER HT 5 Black out 1019 4 Open Black out Strobe at variable speed from slow to fast 3700ms 20ms 120 149 5 F Pulse open at variable speed from slow to fast 42 6s 100ms 150 179 HT l Pulse close at variable speed from slow to fast 42 6s 100ms DMX range Value 180 204 192 Random Strobe Master and RGB active 205 229
19. s for each master Z1 PLUS IP65 can also be remote controlled using the USITT DMX 512 standard digital communication protocol Z1 PLUS IP65 guarantees a full level of IP65 protection against infiltrations of solids and liquids allowing it to be used safely both indoors and outdoors MAIN ELECTRICAL CHARACTERISTICS Input Voltage Range Vin 90 260 Vac Frequency 50 60 HZ Power Consumption Range 8 100 W Power Factor Pf 0 95 electronic PFC controller Efficiency 90 typical IP protection grade IP 65 Output Power Output Range 6 100W per output 1 5 25W per channel Output Current 350 mA 100 per channel 500mA 100 per channel in BOOST Mode Output Voltage Vout 48V Max Load output 15 x FOCUS RGB LED projectors or 15 x MR16 RGB LED lamps or 5 x FOCUS FULL RGBW FULL WHITE LED projector or 5 x MR16 FULL RGBW FULL WHITE LED lamp or 1 x HELIOS R all models LED projector or 1 x TITAN HEAD all models LED projector or 1 x RA7 HEAD all models LED projector or 1 x HORUS all models LED projector or 1 x FOS 100 Plus all models led bar or 3 x FOS 33 Plus all models led bars Min Load output 1 x MR16 RGB LED lamp Control Input Control Signal DMX 512 Dimming System Constant Current PWM Address Range DMX 512 channels addressable by display APPLICATIONS Cinemas Restaurants and pubs Discoteques Architectural Interior and Exterior 3 Z1 PLUS IP65 INPUT OUTPUT CONNECTIONS Mains 90 260 Va
20. y operating mode By setting Emergency mode it will be possible to select one of the 16 preprogrammed WHITE cues that will then ran if DMX Signal is missing or not available Usefull for Emergency EXIT ilumination on public areas ENTER Default OFF Default White 1 Default 255 m m 2 2 m m 7o 7o a 11 Z1 PLUS IP65 MENU Up Down ENTER DEFAULT To restore default settings Internal Unit temperature e MENU Up Down Loe ENTER ENTER Celsius TEMPERATURE Internal Unit temperature visualisation IS IF IS IF MENU Up Down ENTER Up Down LIFE TIME This menu show the total UNIT life time and the RGBA life time o g MENU Up Down ENTER TEST MODE RGB colours test with rainbow IF IF IF cno MENU Up Down ENTER bh i ae SOFTWARE Software version SERVICE MENU For technical personnel only To operate this menu Connect the unit to the main While reset is running press the MENU and ENTER keys at the same time CHANNELS This menu allow to set 3 channels or 4 channels LEDs output mode 3 LEDs channels output mode RGB 4 LEDs channels output mode RGBA RGBW PRODUCT MODEL SELECTION TITAN PLUS Default for Z1 PLUS IP65 FOS 100 POWER only for FOS 100 POWER unit DELTA 8 only for DELTA 8 unit Exit from hidden menu 12 Z1 PLUS IP65 AUTOMATIC OPERATION AUTO Z1 PLUS IP65 can work in automatic mode without a DMX controller First of all connect the pro
Download Pdf Manuals
Related Search