SMS Machine HTTP WapPush User Manual version 1.0.9
Contents
1. SMS Queued to the GSM Modem SMS Received from GSM Modem oo olo SMS sent to the Server SMS Trasmissions Failed O Other Info 9 Logout Firmware version HTTPO1 03 AX Refresh J Release 1 01 Operation status GSM Status e GSM Field Level It is an indicator of GSM field just found by SMS Machine HTTP PUSH modem This value is measured in dBm but also a graphical representation is shown e Modem Status It is a message sent by the modem and it describes the modem status on GSM network HTTP Status e Lan Status It is a message that describes SMS Machine HTTP PUSH status on the local network and the availability of the destination script Delivery Status In this section you find some counters related to SMS transmission and reception All these parameters are not permanent it means they are set to zero when the SMS Machine is turned off e SMS Received via HTTP It is a counter of messages sent to the SMS Machine by mean of HTTP POST requests and accepted in the Microcontroller sending queue e SMS Queued to GSM Modem It is a counter of SMS messages that the SMS Machine actually sends to its modem ready to be transmitted by the SIM card e SMS Received from GSM Modem It is a counter of messages received by the SIM card inside the SMS Machine HTTP PUSH modem e SMS sent to the Server It is a counter of messages received by the SMS Machine and forwarded through HTTP POST requests to the configured sc2. Some terms used throughout this document may be other company registered trademark They are mentioned only with explanation aim and the intention of respecting authorized owner rights Area SX srl will not be considered responsible for eventual damages or losses deriving from this document wrong information SMS Machine is an Area Sx srl registered trademark All rights reserved Safety information SMS Machine HTTP PUSH usage may disturb or damage some nearest electronic equipments operations So it is recommended to avoid SMS Machine HTTP PUSH installation close to e Biomedical electronic devices e Aircraft onboard equipments e Security devices e Audio radio and television systems A complete Dual Band GSM Modem is part of SMS Machine HTTP PUSH This device has the same technical characteristics as normal Dual Band cellular phone so it is recommended the same usage precautions In particular it is recommended not to use SMS Machine HTTP PUSH wherever it is explicitly forbidden the use of cellular phone or generic telecommunication equipment SMS Machine HTTP Wap Push User Manual Page 3 SMS Machine 2009 Area SX srl Introduction to this manual This manual is intended for users who have to manage the following kind of SMS Machine e SMS Machine HTTP PUSH Basic knowledge of computer science in particular TCP IP network is necessary to read this manual Updated versions of this manual may be freely dow
3. User Manual Page 21 SMS Machine 2009 Area SX srl delivery notification request e Ordinary SMS reception up to 160 chars Web script invoked by SMS Machine HTTP PUSH must manage four parameters for each received SMS using POST method Name and meaning of these parameters are the following o Sms num is the sending phone number o sms _text is the message text o Sms date is the date and time of SMS registration on GSM network i e transmission date in format YYYY MM DD HH MM SS GMT XX where YYYY MM DD is the date in format year month day HH MM SS is the time in format hour minute second GMT XX is the offset from Greenwich time Sometimes this information is not correctly managed by mobile operators o sms code may contain the key word for SMS Machine HTTP PUSH authentication upon the web script e Incoming call reception As briefly described in a previous section when an incoming call is received by the SMS Machine HTTP PUSH then it hangs up and executes the same Http Post request toward the configured web script and sending the same parameters Some further details is needed o sms_num is the calling phone number o sms text has always the content INCOMING CALL RECEIVED o Sms date has always a null date as 00 00 00 00 00 00 GMT 00 o sms code may contain the key word for SMS Machine HTTP PUSH authentication upon the web script e Ordinary and extended SMS transmission up to 300 chars Fo
4. When this LED is turned on it means that the Web Server for incoming SMS receipt is unreachable on the network SMS Machine HTTP Wap Push User Manual Page 14 SMS Machine 2009 Area SX srl SMS Machine HTTP PUSH configuration Network configuration First of all you need to configure SMS Machine HTTP PUSH with right IP address and netmask in order to connect it to your network SMS Machine HTTP PUSH has a default network configuration with IP address 192 168 0 101 and netmask 255 255 0 0 Be sure that SMS Machine HTTP PUSH is connected to your LAN through an 10 100Mb Hub Switch and your PC IP address is between 192 168 0 1 and 192 168 0 254 except obviously 192 168 0 101 and netmask is 255 255 0 0 You may connect your PC and SMS Machine HTTP PUSH not only through an Hub Switch but also directly with a network crossed cable CROSS OVER Once your PC is under this condition you would have to reach SMS Machine HTTP PUSH by a simple ping towards its default address 192 168 0 101 To execute a ping towards SMS Machine HTTP PUSH you have to launch a DOS command prompt and type C gt ping 192 168 0 101 If the ping answer is correct you may go ahead to configuration step Configuration WEB interface Of course in order to work properly SMS Machine HTTP PUSH must be configured as a first step This operation is very simple in the current firmware version since no additional software is needed In fact the mac
5. Free the provided GSM antenna cable and insert the FME connector into the socket on SMS Machine HTTP PUSH rear panel as previously described This connector has a threaded metal ring that has to be screwed till the end without forcing GSM antenna connection SMS Machine HTTP Wap Push User Manual Page 12 SMS Machine 2009 Area SX srl Attention Avoid absolutely turning on SMS Machine HTTP PUSH without having already connected the antenna Otherwise irreparable damage may occur to the inner GSM modem Power supply connection Insert the power adapter connector on SMS Machine HTTP PUSH rear panel then plug it into a power supply socket Turn on the switch and check if the green LED on front panel is correctly lit Power supply connection Ethernet network connection Use an ordinary UTP cable with RJ45 plug to connect SMS Machine HTTP PUSH to a network Hub Switch Be sure that Hub Switch socket supports 10Mbit Ethernet devices After turning on SMS Machine HTTP PUSH check if the link LED next the socket is correctly lit You can see it through the pin hole next the Ethernet socket on the rear panel Network connection SMS Machine HTTP Wap Push User Manual Page 13 SMS Machine 2009 Area SX srl SMS Machine HTTP turning on Once all the connections are realized as previously described you may turn on SMS Machine HTTP PUSH using the switch on the rear panel Front panel On front panel you would b
6. 01 GSM Service Centre configuration Message service center number It is the Service Centre number for SMS sending and it is different from one Mobile Operator to another Clicking one of the three major mobile operator logos you will automatically fill this field Please remember to cancel this information from the SIM card with an ordinary mobile phone before using it on SMS Machine HTTP PUSH SMS Machine HTTP Wap Push User Manual Page 18 SMS Machine 2009 Area SX srl HTTP When an SMS is received SMS Machine HTTP PUSH sends its information message text sending number sending date and optionally an authentication code to a web server script and cancels it from the SIM card memory In other words the machine works as a browser does when it sends to a web script some data inserted in a form So the Machine executes an HTTP POST request and the parameters of this page define this communication mode Destination server Address O Advanced Www areasx com Destination server Page Current Status ricevi_sms php Configuration Test TCP Port number 80 Security code Enable TOP Server checking vi Use HTTP HEAD for script checking vi Send a POST when a RING is received d Save Logout Release 1 02 HTTP SMS receipt script configuration Destination server Address This parameter must be configured with the IP address or name of the web server whe
7. SMS per hour e Reception top speed 300 SMS per hour GSM modem characteristics e GSM Modem Telit GM862 Quad band Network microprocessor characteristic e Core module Rabbit Semiconductor RCM3700 16 bit 22Mhz e 512Kb SRAM memory 512Kb FLASH memory e Ethernet RJ45 10Base T socket on board Power adapter electrical characteristics e Wall plug e Input voltage 230 Volt AC 50 60Hz e Output voltage 12 Volt CC DC 500mA SMS Machine http electrical characteristics e Average current consumption 300mA e SMS Machine HTTP PUSH operating temperature 0 55 SMS Machine HTTP Wap Push User Manual Page 27 SMS Machine 2009 Area SX srl Technical support SMS Machine Home Page At the URL http www smsmachine it you will find all SMS Machine products official home page Starting from this page it is possible retrieve the following information e SMS Machine new version announcement e Updated version of user documentation e Detailed technical documentation e PHP ASP and Visual Basic using examples e Support software If you have any technical or commercial question you may contact us by mail phone or fax Our references are shown throughout this manual Firmware update SMS Machine HTTP PUSH firmware is periodically updated by Area SX srl technical staff in order to improve performances and functionalities SMS Machine HTTP PUSH firmware update availability is announced on the official SMS Machine home page at the URL www sms
8. Web site or application SMS Machine HTTP Wap Push User Manual Page 8 SMS Machine 2009 Area SX srl SMS Machine HTTP PUSH installation Package description SMS Machine HTTP PUSH is delivered inside its cardboard box well protected from mechanical shocks that may occur during transport Once you opened the package you will find the following 1 SMS Machine HTTP PUSH 2 A set of screws to lock SMS Machine HTTP PUSH case after SIM insertion in the GSM modem 3 4 5 User documentation both the paper one and over a CD A GSM antenna with magnetic base and 2 5m cable A power adapter Bu Si Ses hip le ley Sa DR lettro SMS Machine HTTP PUSH package Each component has been accurately checked before delivering SMS Machine HTTP PUSH as testified by the technical certificate given with the device Please avoid using third party components that may damage SMS Machine HTTP PUSH inner devices SMS Machine HTTP Wap Push User Manual Page 9 SMS Machine 2009 Area SX srl Installation requirements To succeed in SMS Machine HTTP PUSH installation you need 1 A SIM card belonging to any mobile operator both prepaid or not Before inserting the SIM card into SMS Machine HTTP PUSH you should try it with an ordinary mobile phone to verify that it is able to send and receive SMS and PIN is disabled You have also to cancel the mobile operator Service Centre number from
9. useful if you want to integrate SMS Machine configuration features in your own Web application In all other cases it is sufficient to use the web interface Configuration script is available at the URL http smsmachine_address setconfig cgi Parameters name to send in HTTP POST mode are e Pwd password that allows SMS Machine to accept the transaction default SMS1234 e IpAddress IP address to assign to SMS Machine e Netmask SMS Machine subnet mask e Gateway gateway IP address e Nameserver DNS server IP address e NewPwd new password to assign to SMS Machine e Servicecenter number of the Service Centre for SMS sending e ServerAddress IP address or name of the destination server for received SMS e ServerPage path of the destination script for received SMS starting form the server root e ServerPort port for HTTP transaction default value 80 e ServerCode key code that SMS Machine will use for authentication to Web script e ScriptCheck control of the reception script or server value 1 enables HTTP HEAD request on the script and value 0 only control on the TCP socket e InBufferLen number of SMS in the buffer for transaction to the reception script default value 1 e ServerTimeout timeout of the HTTP TCP connection to the script server in millisecond default value 5000ms e MaxFailureln maximum number of attempts for received SMS forwarding to the script server default value 0 means endless attempts SMS Machine answers with a s
10. A EE 25 Factory configuration restoring ssssssessnnnesnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn nnmnnn nnmnnn nnmnnn nnmnnn 26 SMS Machine HTTP Wap Push User Manual Page 5 SMS Machine 2009 Area SX srl Technical Characteristics ccceecccceeeeeceeeeeeeeeeneeeeseeeseeeseensnee seen sneeseeg anes WAKE WA WARA KAWA AA WA WEKA WA WA AA KA WA AA WA WA AA WA WA AA WA WA AA WAA 27 Stelle EE 27 GSM modem Characteristics iii 27 Network microprocessor characteristic lllllli kk kk ak kk ak kak k k A kK kA KAKA KAKA AA A KA AA 27 Power adapter electrical characteristics A 27 SMS Machine http electrical characteristics cee eeeeaeeeeeeeeeeeecaaaeeeeaeeseeeeesaeeseaaeeeeneeseaeess 27 Technical SU DROE eege Ee EE 28 SMS Machine Home Page iii kake keka kake kake k KE KA HEKA KAKA KAKA KAKA KAKA A HH KA HA KA HE KA HA KA KAKA KARA KAKA kK KA kK RR 28 Firmware Update msn sie tia niet Ny Keye PRA aa eee kes k iaia ini 28 Appendix A HTTP interface 000 EEN WAA KA WEKA WA WEKA WA WARA WA WA AA WA HAAA WA WA AA WA WA AA WA WA AA WA WA AA WAA 29 SMS Machine identification i 29 SMS e en TEE EE 29 Ee E IECH 20 SMSuunsuccesstul transmission d e ee ciy ZEN eet aed ee dawa r A ed 31 len e IEN 32 Operation REH E HEET 32 Network and configuration parameters request Ek kk kek KAKA KE KAKA kK A KAKA KA KAKA K
11. A KA 33 SM amp reception emulationi miti iaia kiyak Kak d eee ieri adn Ua kan S R WA a HEVA kala V GA 34 SMS Machine HTTP Wap Push User Manual Page 6 SMS Machine 2009 Area SX srl Product description SMS Machine HTTP PUSH is a telecommunication device that allows your Web applications to be quickly integrated with SMS messaging over GSM network The new of this updated version is the deployment of WAP PUSH technology that allows sending not only ordinary SMS text messages but also active SMS In fact the Push mode allows sending SMS messages formatted so they can directly interact with destination mobile device In particular it is the parameter called Destination Port that determines the action to be taken on the terminal A typical example is that regarding the hyperlinks sending An SMS text message containing a link causes on destination terminal only visualization only few devices can recognize the link but an SMS Push allows notifying directly the information with the option of immediate connection if this option is enabled Another example needs a further and deeper level of interaction with terminals supporting Java J2ME applications In this case the SMS Push message can be handled directly by the application running and listening on a specific port so that a related action according to the message content may be executed For example remote control applications chat games etc SMS Machine HTT
12. MS default value if missing 1 Wap Push other values to be specified Please refer to the section dedicated to SMS sending e num SMS addressee phone number e text SMS message text 160 chars are available up to 300 chars for extended SMS also known as chained The exceeding chars are ignored SMS Machine answers with a string without any HTML tag but however displayable by a browser that contains two parameters and their values The first parameter is errno followed by its description and its values are e errno 0 amp desc SMS queued SMS successfully put in sending queue e errno 1 amp desc Access denied Wrong password e errno 2 amp desc Destination number missing SMS addressee phone number is missing e errno 3 amp desc SMS refused SMS refused because the sending queue is full The second parameter is SmsIndex and it is a progressive index that identifies the SMS successfully put in sending queue To verify if the message has been sent by SMS Machine you may check the SMS sent counters increment on the Status page Alternatively you may check the TxGsmCounter and TxServerCounter parameters retrieved with the getstatus cgi see later section Delivery notification request The new version of SMS Machine can also send SMS message requesting the notification of delivery to the addressee as mentioned in the previous section In this case the HTTP POST request to the smssend cgi script must be modified adding the optional pa
13. Machine will act as defined in the configurations section dedicated to Advanced parameters Please refer to that section for details SMS Machine HTTP Wap Push User Manual Page 29 SMS Machine 2009 Area SX srl Extended SMS reception The new version of SMS Machine is able to receive also extended messages also know as chained that means SMS with more than 160 chars allowed by the standard Anyway each extended SMS message is actually divided in so much different SMS parts as needed to fit the whole transmitted text So the SMS Machine treats all the parts as single messages executing an http post for each of them Obviously new parameters are needed for the original message reconstruction Therefore in the HTTP POST request not only the former parameters just described are sent but also the new ones used to identify and reconstruct the extended SMS starting from its component parts e sms_id identification number for the extended SMS e sms_totparts number of the extended SMS component parts e sms_thispart identification number for the current SMS part Delivery notification SMS reception The new version of SMS Machine can also send SMS message requesting the notification of delivery to the addressee For this function please see next section In this section the reception of the notification itself will be described The reception of a delivery notification is treated as a normal SMS but its message text will b
14. P PUSH In a 125x175x45 mm case SMS Machine HTTP PUSH encloses a Quad Band GSM modem capable of receiving and sending SMS messages over GSM network and a network processor with Ethernet connection capable of internetworking with Web applications on every platform In order to work properly SMS Machine HTTP PUSH needs an ordinary SIM card belonging to any mobile operator that is qualified to send and receive SMS messages On reception SMS Machine HTTP PUSH receives SMS on the SIM card inserted in the modem and it forwards the messages contents towards any Web script asp php pl cgi jsp etc with an HTTP POST transaction Some HTTP parameters will contain the message sender phone number the message sending date and text On transmission SMS Machine HTTP PUSH accepts HTTP transactions in POST mode it extracts message text and addressee phone number from HTTP parameters and sends the SMS on GSM network Of course among these needed parameters there is also the port related to the SMS that determines if it is text message or Wap Push message SMS Machine HTTP Wap Push User Manual Page 7 SMS Machine 2009 Area SX srl Connections between SMS Machine HTTP PUSH and Web Server Using SMS Machine HTTP PUSH there s no need of serial RS232 modem or managing applications that run apart the Web Server but you need only to write simple interface scripts maybe in the same programming language you use for the rest of your
15. S not transmitted by the modem Network error information coded by the ServerStatus parameter is also shown by the green LED L2 on front panel Failed GSM network registration information coded by the LastGsmError is shown by the long lighting of red LED ERR on front panel The information about failed SMS coded also by the FailedCounter parameter is shown by the simultaneous blinking of red LED ERR and the green one L1 for some seconds and for each message Network and configuration parameters request It is possible to retrieve configuration parameters current values by requesting this cgi script http smsmachine_address queryconfig cgi It is also the script used at the login in web interface in order to load all the current parameters An HTTP POST request must be used sending the following parameter e Pwd password that allows SMS Machine to accept the transaction SMS Machine answers with a string without any HTML tag but however displayable by a browser that is composed by the concatenation of pairs parameter name value Parameters are e errno 0 amp desc Configuration Sent correct parameter loading or errno 1 amp desc Access denied wrong password e IpAddress current IP address of the SMS Machine e Netmask SMS Machine subnet mask e Gateway gateway IP address e Nameserver DNS server IP address e Fversion firmware version e Servicecenter number of the Service Centre for SMS sending e ServerAddress IP ad
16. SMS Machine 2009 Area SX srl mi pad nine http www areasx com SMS Machine HTTP PUSH Gateway LAN SMS with WAP Push Technology User Manual Firmware Version 1 0 9 SMS Machine HTTP Wap Push User Manual Page 1 SMS Machine 2009 Area SX srl Congratulation for choosing SMS Machine Area SX srl thanks You for the preference you gave us by choosing an SMS Machine device and is always available for any commercial or technical information Contacts Updated information about SMS Machine devices and latest software release are available on our Web Site at the address http AWwww areasx com bal J Ex coca P Cerca o E y YY Segnalbriy h9 bloccati YF Controlo 3 Traduci nviaav A Impostazioni Zo deb Pagina Ji Strumenti gt GATEWAY ICT Solutions SMS lt gt HITE Home Articoli Divulgativi Listino Prodotti Le ultime novit Carrello Elettronico Contatti e Supporto Cerca ETGEN Quum armco Articoli Divulgativi a o Listino Prodotti Una nuova versione per la fortunata SMS Machine HTTP perfettamente compatibile SMS Machine HTTP Aree Tematiche con la precedente la nuova release consente anche l invio di messaggi di tipo Wap Push SMS ma TIE LA attivo in grado di interagire direttamente con il terminale mobile che li riceve In non solo particolare possono essere inviati messaggi contenenti link o diretti verso applicazioni Jav
17. TP PUSH executes the control simply opening and closing a TCP IP connection toward the server and its port configured as described above On the contrary if the box is checked then the script control is deeper and it is carried out using an HTTP HEAD request Please note that for some web server implementation this request causes the response of just the script header without the complete script code execution For other versions this request may cause the complete script code execution so you have to keep in mind and or verify this aspect when the option is used Enable TCP Server checking Sometimes it may be useful disabling completely this check in one of the two ways just described To do so just keep the checkbox not flagged Please note that in this case the SMS Machine HTTP PUSH will always try to send to the Server the received messages Send a POST when a RING is received The SMS Machine HTTP PUSH can manage also an incoming call if the used SIM card is enabled for voice traffic The behaviour of the machine in case of incoming call is very similar to that when an SMS is received For this reason please see the next section dedicated to this function for further details At this moment just note that the incoming call managing function is enabled or disabled according to the selection of this checkbox Advanced Even if the parameters configured as described in the above sections are sufficient to let the SMS Mach
18. TP Wap Push User Manual Page 10 SMS Machine 2009 Area SX srl SIM card insertion Push the SIM card to the bottom of its socket until you will feel a little leap which means it is locked When it is necessary to unlock the SIM and release it you need to slightly push on its edge in the same direction of insertion An inner spring will push the SIM card outside enough to grab it To close the case make its cover slide backward paying attention to the signalling LEDs they must be correctly aligned to their front panel holes Now you need to lock the case with the provided four screws as shown by the next figure SMS Machine HTTP PUSH case locking SMS Machine HTTP Wap Push User Manual Page 11 SMS Machine 2009 Area SX srl Connections Rear panel Next figure shows a sketch of SMS Machine HTTP PUSH rear panel Here the description 1 FME socket for GSM antenna In order to protect GSM modem from damage avoid carefully turning on SMS Machine HTTP PUSH without having already connected antenna cable to this socket 2 Power supply Use only the provided power adapter to protect SMS Machine HTTP PUSH inner device from damage due to third party component Power switch 3 4 Ethernet RJ45 socket for LAN connection pin hole for link LEDs status checking 5 Entry for optional expansions 6 Button for factory configuration restore SMS Machine HTTP PUSH rear panel GSM antenna connection
19. a residenti sul cellulare di destinazione Unitamente a queste nuove funzionalit la SMS Machine HTTP PUSH raddoppia anche le prestazioni di invio e ricezione della versione standard ed integra i pannelli di configurazione direttamente nel firmware a interfaccia operatore per le schede SX ARM Linux e FOX Processori Rabbit Processori BasicX Convertitori EZTCP Le ultime novit Aggiornamenti sito Bookmarks Area Download SMS Tutte le novit in SMS Machine HTTP Wap Push convertitore Seriale Ethernet in soli 8 cm per 5 Megapixel un modo creativo di utilizzare il dimmer Mappa del Sito ppe Vezio GPS un modem un ricevitore GPS ed un microcontrollore in un solo prodotto L EZ10 GPS la sintesi perfetta delle esigenze attuali nel campo del telecontrollo e del posizionamento geografico un modem GSM GPRS quand band un ricevitore GPS 7 a 20 canali 4 linee di ingresso uscita un microcontrollore con interprete Python un contenitore gi pronto per le esigenze del mercato automotive il tutto con dimensioni estremamente ridotte Realizzare un completo telecontrollo via GSM con la SXPY Gamma SMS Machine SMS Machine Web mini SMS Machine SMS Machine HTTP Le applicazioni di questo prodotto sono innumerevoli pu essere utilizzato da solo per SMS Machine MAIL realizzare sistemi di tracciamen
20. assword that allows SMS Machine to accept the transaction The SMS Machine answers with a string without any HTML tag but however displayable by a browser that contains some pairs of parameter name value tied together by the character amp as in the following example rrno 0 amp desc Machine ID Reported Machineld 0090C2D3505A e errno is the error code for the transaction values are 0 if it is OK or 1 for wrong password e desc describes shortly the transacion result for example Access denied e Machineld e g Machineld 0090c2c68ab5 is the Mac Address that identifies definitively SMS Machine SMS reception When SMS Machine receives an SMS message data are sent towards a Web script in an HTTP POST transaction This means that SMS Machine emulates a Web browser behaviour when the user fills a form and submits the data as already shown in the configuration section dedicated to the HTTP setting For example if you use the following script for each incoming SMS SMS Machine HTTP will call rxmsg php script inside the smstest folder of www areasx com Web server sending four parameters e sms_num SMS sender phone number e eme date SMS sending date with the format YYYY MM DD HH MM SS GMT 00 e sms text message text e sms_code Web script key code if set during configuration SMS Machine HTTP waits for the standard success answer from the Web server In other cases HTTP transaction is considered incomplete and SMS
21. dress or name of the destination server for received SMS e ServerPort port for HTTP transaction default value 80 e ServerPage path of the destination script for received SMS starting form the server root SMS Machine HTTP Wap Push User Manual Page 33 SMS Machine 2009 Area SX srl e MaxFailureln maximum number of attempts for received SMS forwarding to the script server default value 0 means endless attempts e ServerTimeout timeout of the HTTP TCP connection to the script server in millisecond default value 5000ms e InBufferLen number of SMS in the buffer for transaction to the reception script default value 1 e ServerCode key code that SMS Machine will use for authentication to Web script e ScriptCheck control of the reception script or server value 1 enables HTTP HEAD request on the script and value 0 only control on the TCP socket SMS reception emulation It is also available a cgi script that makes SMS Machine emulate SMS reception This function may be very useful because it allows checking server configuration without sending any actual SMS In fact SMS Machine makes an HTTP request to the web script you set in HTTP web page using default parameters This is the URL for the request http smsmachine_address srvtest cgi The parameter to be sent with an HTTP POST request is e Pwd password that allows SMS Machine HTTP to accept the transaction Possible SMS Machine responses are e errno 0 amp desc SMS queu
22. e able to see signalling LEDs as the following e GSM LED yellow Blinking e PWR LED green Turned on 8 eS o e ERR LED red Turned on Si O MO e L1and L2 LED green Turned off L1 j After about 30 seconds ERR red LED has to turn off to showing modem registration over GSM network and firmware correct operating status If it doesn t happen try to move GSM antenna and turn on SMS Machine HTTP PUSH again If it doesn t happen again be sure you have done the following e Disabled SIM card PIN request using an ordinary mobile phone e Checked that SIM card is qualified e Checked that there is good GSM field level where you placed the antenna Front panel LEDs meaning GSM yellow LED This LED shows GSM modem operation A fast blinking means that the modem is attempting to register over GSM network When blinking becomes slower it means modem is registered and SMS Machine HTTP PUSH is ready PWR green LED This LED shows a correct power supply status ERR red LED This LED is on when SMS Machine HTTP PUSH microprocessor encounters an error It is also on when you have just turned on SMS Machine HTTP PUSH until the modem is registered over GSM network then it turns off L 1 green LED This LED shows that SMS Machine HTTP PUSH is sending or receiving a massage over GSM network If L1 and ERR are on together it means that SIM card is missing or it haven t been correctly inserted in the modem L 2 green LED
23. e always STATUS REPORT Anyway also in this case new parameters are needed within the HTTP POST request in particular e sms id identification number equal to the index retrieved with the SMS transmission see also next section e sms status status code returned by the GSM network The expected value for this last parameter is 0x00 that means the status of SMS delivered Also other values for different network conditions are possible the most common are the following ones 0x00 Short message delivered successfully 0x01 Forwarded but status unknown 0x20 Congestion still trying 0x21 Recipient busy still trying 0x22 No response recipient still trying 0x23 Service rejected still trying 0x24 QOS not available still trying 0x25 Recipient error still trying 0x42 Connection rejected 0x45 No internetworking available 0x46 Message expired 0x48 Message deleted by SMSC SMS transmission When transmitting messages SMS Machine emulates a Web server behaviour listening on port 80 while your application has to emulate a Web browser behaviour calling a SMS Machine embedded CGI This is the request http smsmachine_address smssend cgi SMS Machine HTTP Wap Push User Manual Page 30 SMS Machine 2009 Area SX srl This request must be carried out in POST mode for sending SMS message parameters which are e Pwd password that allows SMS Machine HTTP to accept the transaction e Push destination port O text S
24. ed emulated SMS successfully queued e errno 1 amp desc Access denied Wrong password SMS Machine HTTP Wap Push User Manual Page 34 SMS Machine 2009 Area SX srl SMS Machine HTTP Wap Push User Manual Page 35 SMS Machine 2009 Area SX srl SMS Machine HTTP PUSH is produced by AREA SX SRL INFORMATICA amp MICROELETTRONICA Via Stefano Longanesi 25 00146 Roma ITALIA Tel 39 06 99 33 02 57 Fax 39 06 62 20 27 85 info areasx com http www areasx com SMS Machine HTTP Wap Push User Manual Page 36
25. hine supports a micro web server with a front page developed in Macromedia Flesh so you have just to use your favourite browser from a PC and link it toward the machine default IP address http 192 168 0 101 The accessed main page is shown in next picture No operation is possible yet at this step but only status monitor is allowed In fact the home page summarizes the status of the SMS Machine HTTP PUSH and all the displayed parameters will be analyzed in the following sections SE fi WWww areasx com GSM Status GSM Field level j 87 dBm Modem status Gsm Ok HTTP Status Lan status Cannot resolve sms domain it Delivery Status SMS Received via HTTP O SMS Queued to the GSM Modem 0 SMS Received from GSM Modem 0 SMS sent to the Server O SMS Trasmissions Failed O Other Info Firmware version HTTPO1 03 AX Refresh Status Go to the configuration page O Home page of the SMS Machine web interface SMS Machine HTTP Wap Push User Manual Page 15 SMS Machine 2009 Area SX srl It is now important to remind that the browser you use must support an appropriate Flash Player From the home page you may enter the login page that is needed to actually execute configuration operation simply by clicking on Go to configuration page The login page is shown in the following picture the default password to type in is SMS1234 and then just clock on Logi
26. iii 15 EEN elt en le TE le EE 15 Configuration WEB interface A 15 GetilD NUmber a aes ina chev aa ai aa Deliri 17 LAN i ee id e e e eer reece 17 IP Addres ZE DEM e E N EE 17 Nemas Ka dnin Rayi pareyan y Q nda y HI SKeRa K D KA KE Keke EEN Eege DEE pra d an p r kw a 18 EE 18 DI NES iaia i reciept e Ia og io it reer eee i ii iu 18 New password Repeat password ui 18 GSMi fasta ii Sira ie e ro ion ao 18 Message service center NUMDET lewlak b ke kaye k n be y k kay ked kk b ya KAR kk k ea y ek kw sk ked T 18 SEN ae KAN I i DE o e tre ON cha ged o bad nen Te ening i dog hc ah SEA AK n 19 Destination server Address thai iaa 19 Destination server le iaia e AL AR R era KAK XW Q pa nak 19 TGP ele elle 19 e Eiere 19 Use HTTP HEAD fer script checkingi iii iaia olio sbirri 19 A E DO O WEE 20 Maximum server delivery tres aaa aa ana dali 20 Timeout waiting for server answer i 21 Incoming messages buffer length ooooooccnnnnccccononccccnnoncnconnnnnccnnnnnnnnnnnnnnc E cnn narran 21 Communication parameters name i 21 Current ET 22 ET 23 FEE EP Status sce isdi en Gitte chien Gite hers les E 23 Delivery al 0 eegen aa iii Ee 23 Other lte EE 24 Orola lile Ee TOS PARA cas se ke all ica eat 24 Send aN RX SIMULAIN saene aa naa ira hai died inlined Gade elisa 24 Send Message EE 24 Es e 810 SE N E E OEA ea E cardi A A OE T A AO E N
27. ine HTTP PUSH work properly there are also other advanced parameters under the user control designed to optimized the http communication with the destination script In this section they will be described in detail reminding also their default value Stee www areasx com Maximum server delivery tries 0 This parameter sets the number of tries that will be made by SMS Machine to transfer an incoming SMS to the server before discarding If it s set to 0 the SMS transfer will be tried forever Current Status O SI Timeout waiting for server answer millisec 5000 This parameter sets the number of milliseconds that SMS Machine will wait O Configuration Test for the server to answer to the socket requ Incoming messages buffer length 1 This parameter sets the maximum number of SMS messages that can be kept in the SMS Machine buffer waiting to be delivered to the server A larger number can improve the SMS troughput but you will be exposed to buffered SMS losses if the power fails If the parameter is set to 1 the troughput may be slower but you will not lose SMS s if a power failure happens Warning wrong settings of the parameters in this page may cause incorrect behaviour of SMS Machine Save Release 1 01 Advanced advanced parameters of http communication Maximum server delivery tries This parameter means the maximum number of attempts that SMS Machine HTTP PUSH executes for transmitting
28. iting for server answer This parameter means the maximum time that can pass between an HTTP POST request carried out by the SMS Machine HTTP PUSH toward the reception script and the related response with a 2000K Once this timeout has expired the machine assumes the transaction failed and executes the configured operations as described in previous section so it tries a new attempt or discards the SMS message cancelling it from SIM card memory The unit is millisecond and the default value is 5000 ms 5 sec The criterion in choosing this parameter needs the knowledge of the reception script behaviour in normal condition e g elaboration delay delay for database access etc and the network traffic or the routing delay e g over LAN to Internet In fact you have to note that low values for this timeout may speed up the communication but the risk is that SMS Machine HTTP POST assumes as failed simply a slow transaction so causing useless new transmission attempts Vice versa high values for this timeout may slow down the communication since it takes much time in recognizing the failed ones but on the other hand prevent from useless retransmission in case of elaboration routing delay Incoming messages buffer length The SMS Machine HTTP PUSH can search for new SMS messages received on the SIM card one by one or more In this second case they will be temporarily stored in a buffer waiting to be forwarded to the reception script This para
29. machine it or on our company web site www areasx com For firmware updating you need optional Rabbit programming cable R101 0542 and its managing software These products are available on the same web sites This cable will be connected on one side to a RS232 serial port of a Windows PC and on the other side to the core module Rabbit 3700 The managing software will download new SMS Machine HTTP PUSH firmware An alternative and easier way to execute firmware update is over the LAN Contact Area SX for detailed information Further information about Rabbit 3700 Network Processor that are used on SMS Machine products are available on web site http Awww rabbitsemiconductor it SMS Machine HTTP Wap Push User Manual Page 28 SMS Machine 2009 Area SX srl Appendix A HTTP interface In this section all the cgi scripts supported by the SMS Machine HTTP PUSH will be described in detail when it acts like an http server but also its behaviour as an http client Please note that in the following sections the device will be simply called with the name SMS Machine SMS Machine identification SMS Machine is identified not only by its IP address that can be changed as you want but also by its Mac Address that cannot be changed Mac Address is a twelve hexadecimal character string that can be retrieved by calling an SMS Machine inner CGI script with an http post request as in the following example and sending the parameter e Pwd p
30. meter just defines the buffer length default value is 1 and maximum value is 10 A larger buffer can speed up reception operations since fewer accesses to SIM card memory are needed but on the other hand the risk is messages lost since the buffer memory is cancelled for example if the machine is turned off On the contrary buffer length value to 1 prevents from messages lost even in case of accidental machine power down since they are stored in SIM card memory but it could slow down reception operations Now it is clear that the reception operations may be speeded up or slowed down rather they may be more or less reliable in terms of SMS lost according to the modulation of three parameters described above For this reason it is highly recommended their accurate evaluation according to the condition of the network where the SMS Machine HTTP PUSH will work and the service reliability features Communication parameters name Even though the communication http interface used by the Machine will be described in appendix A by now it can be already useful to describe with a certain level of details the http parameters for the communication between the Machine and the external application both for sending and receiving SMS Anyway please refer to the Appendix for all the details about the new functions the reception of extended SMS also know as chained message with more than 160 chars transmission of SMS with SMS Machine HTTP Wap Push
31. n button Ste Wwww areasx com Insert the configuration password default SMS1234 Configuration password O Login Login page If the login is successful you will enter the functions menu page that you can see in the following picture If it is not the case then check the password or the network settings as described in the previous section o E Des ee O HTTP O Advanced O Current Status O Configuration Test Machine ID Number Get ID Number Logout Release 1 01 Functions menu Starting from this menu it possible to access the configuration of all the SMS Machine HTTP PUSH parameters Each configuration interface has a button labeled SAVE to actually load SMS Machine HTTP PUSH with new parameters Please note that if this buttons is not clicked SMS Machine HTTP PUSH will not be updated with the changes you made Machine ID Number window allows SMS Machine HTTP PUSH identification with its Mac Address Each function and configuration parameter description follows SMS Machine HTTP Wap Push User Manual Page 16 SMS Machine 2009 Area SX srl Get ID Number As soon as you logged SMS Machine HTTP PUSH identifier is not yet available as shown in the windows in the middle of the interface Clicking on Get ID Number button it is retrieved with a request to the SMS Machine HTTP PUSH The ID is the Mac Address itself To come back to this function you need to logout a
32. nd login once again S Eine ure O Advanced O Current Status Configuration Test Www areasx com Machine ID Number Get ID Number Logout Release 1 01 SMS Machine HTTP PUSH ID Number LAN This interface allows the configuration of all parameters related to SMS Machine HTTP PUSH networking Be careful in configuring correctly these parameters in case of mistake you would not be able to reach SMS Machine HTTP PUSH on your network anymore If it happens you may follow the procedure described ahead for factory configuration restoring ellen www areasx com IP Address Netmask 192 168 0 101 255 255 0 0 O Current Status Gateway DNS 192 168 0 1 192 168 0 1 O Configuration Test New password Repeat password a Save Logout Release 1 01 LAN network parameters configurations IP Address It is the new IP address you eventually want to assign to SMS Machine HTTP PUSH In fact if default IP address 192 168 0 101 doesn t fit to your network you may chose whichever other address to assign to SMS Machine HTTP PUSH SMS Machine HTTP Wap Push User Manual Page 17 SMS Machine 2009 Area SX srl Attention once changed the IP address or other network parameters see also next sections SMS Machine HTTP PUSH notifies with a popup that configuration has changed and it reboots network interface So it doesn t respond anymore to menu command
33. nloaded from our web site at the address http www areasx com SMS Machine HTTP Wap Push User Manual Page 4 SMS Machine 2009 Area SX srl Table of contents Congratulation for Choosing SMS Machine cccesccsseeeeeeeeeeeeeeeeesesneeenseeeeseeeeseaeseseeeenseeeseeesasnaesasenensnees 2 Te ilaele ener 2 Warnings renti eolie it xak e Sk we rie iii a db rie inc nie 3 W lle Ree dn Lu SE 3 Safetyintorm le 3 Introduction to this manual eceeeeceeeeeeeeeeeeee rre 4 NG E d e Lee eee eee 7 SMS Machine HTTP PUSH installation rin 9 Package descriptions aria etica EE 9 Installation requirements italia leali alia iaia 10 SIM card insertion senati Gk deh Seta ie ee eta nali aan 10 EE e Vu soca E rien ori 12 Rear PANS his cessed igloo olii alii i ii ai i lily 12 GSM antenna connectioni cx xl m l kel n aerea 12 Power supply GohndGti0n k gt 5 nadal dela latino iui Veke Xu EN RAA VA K kwa xan aa ey k 13 Ethernet network Connection rooi Axay Awe silk x ka ke xeyl ariani ks KA Y k Kek Ya xw kb ea keke w kn kec 13 SMS Machine HTTP turning 0N in 14 Front panel scparl Nalin ala Maia a 14 Front panel LEDS Meanings EE EE 14 JEY e1 le DAN geegent 14 PWR Green LED yaka ea a kO SEK a deye can s ka ey Ae kuya KUNA e kek alia Aa 14 He RE RE 14 a Beien RR EE 14 Legen CED EE 14 SMS Machine HTTP PUSH configuration
34. r SMS sending SMS Machine HTTP PUSH acts like Web server using its smssend cgi inner script that accepts four parameters delivered in an HTTP POST transaction Name and values of these parameters are the following o num is the addressee phone number o text is the message text 160 chars are available for ordinary SMS up to 300 for extended SMS or chained SMS The exceeding chars are ignored o Push defines if the SMS message is the normal kind Push 0 or Wap Push Push 1 or other value different form 0 Wap Push kind messages are able to interact with the destination mobile phone as already described in previous section In particular with the value Push 1 the SMS delivers a hyperlink while different values can interact with J2ME application for example See following sections for the exact message format description when the SMS Wap Push kind is used o Pwd is the script access password and it is the same you use with the login Current Status This interface shows some information about SMS Machine HTTP PUSH current operation status Refresh button reloads this information SMS Machine HTTP Wap Push User Manual Page 22 SMS Machine 2009 Area SX srl SC all ST www areasx com O HTTP GSM Status O Advanced GSM Field evel j BIJ EI 87 dBm Modem status Gsm Ok HTTP Status Lan status Server Connectior OK O Configuration Test Delivery Status SMS Received via HTTP
35. rameter e notify values 1 to enable the notification function 0 or missing for ordinary SMS SMS unsuccessful transmission Messages that SMS Machine is not able to send no GSM field wrong addressee phone number etc are cancelled from its queue to avoid a blocking status The SmsIndex parameter allows having trace of these missing messages by calling an SMS Machine CGI This is the request http smsmachine_address smserror cgi This request must be carried out in POST mode for sending the following parameter which is e Pwd password that allows SMS Machine to accept the transaction SMS Machine answers with a string without any HTML tag but however displayable by a browser that looks like the following rrno 0 amp Desc Queue Transimitted amp SmsTxErrIdx 2 0 0 0 0 This string contains the following parameters e Errno its values are 0 for successful request and 1 amp desc Access denied for wrong password e SmsTxErrldx is the dotted list of last five failed SMS index SMS Machine HTTP Wap Push User Manual Page 31 SMS Machine 2009 Area SX srl Configuration Also for parameters configuration and for some other support functions SMS Machine offers some cgi scripts to be requested by an HTTP client on port 80 These scripts are the same used by the configuration web interface developed in Macromedia Flash MX that is just an HTTP client communicating with the SMS Machine Note that configuration scripts may be
36. rator Service Centre setting e Message Text If you want to send an ordinary SMS then this field has to be filled with the message text up to 160 chars available The Push Destination Port parameter must be left blank or equal to 0 see also next items If you want to send a Push SMS containing a web link to the destination mobile phone then this field has to be filled with the following format www areasx com This is a link to Area SX web site It means that the format must contain the destination URL without the http protocol and the text displayed in the SMS joined together by the character without any space Please note that the Push Destination Port parameter must be set to 1 see also next item Finally if you want to send a SMS formatted on a different destination port then the text will be composed according with the specific features of the application that will manage it e Destination number It is the SMS addressee phone number SMS Machine HTTP Wap Push User Manual Page 24 SMS Machine 2009 Area SX srl e Push Destination Port It is the option indicating the SMS message transmission mode If this parameter is set to 0 or it is missing since 0 is the default value then a ordinary text SMS will be sent If this parameter is set to 1 then a WAP PUSH SMS message will be sent driving a hyperlink on the destination mobile terminal Of course the text field has to be configured as described abo
37. re the SMS Machine HTTP PUSH sends the received SMS Please note it must be typed without the http protocol e g www areasx com or 192 168 0 1 Destination server Page This parameter must be configured with the complete path and the name of the script listening on the Web Server where the SMS Machine HTTP PUSH sends the received SMS Please note it must be typed with an initial slash and with the classical nested path e g SMS_Machine Received_SMS rxsms php In other words the two previous parameters joined together form the complete URL used by the SMS Machine HTTP PUSH at SMS messages reception TCP Port number It is the port number on which the HTTP request is sent Default value is 80 HTTP well kwon port Security code It is the key word that SMS Machine HTTP PUSH may use for its authentication to the reception web script Of course this value must match the one used by the web script itself Use HTTP HEAD for script checking SMS Machine HTTP PUSH checks for the availability of the web script destination of the received SMS configured as described above In fact if the script were unavailable then it would be useless to start http transaction engaging the microprocessor and its network interface This control may be carried out in two ways depending on this parameter setting SMS Machine HTTP Wap Push User Manual Page 19 SMS Machine 2009 Area SX srl If this box is unchecked then SMS Machine HT
38. ript e SMS Transmissions failed It is a counter of SMS messages that the SMS Machine wasn t actually able to delivery to the GSM SMS Machine HTTP Wap Push User Manual Page 23 SMS Machine 2009 Area SX srl network for example because of no credit wrong SMS Center or low field These messages after the sending attempts are discarded from the queue Other Info It is the firmware version stored in SMS Machine HTTP PUSH memory Configuration test This page allows you to test SMS Machine HTTP PUSH settings both for sending and receiving messages ee ere www areasx com Can This functions allows you to test your configuration parameters O Advanced Use the button below to send a simulated SMS reception request to the configured server O Current Status x Send an RX simulation Use the form below to send an SMS from the SMS Machine SIM card Message Text Destination Number Push Destination Port Logout Send Message J Release 1 01 Configuration test page Send an RX simulation This is the button to emulate SMS reception and it allows easy checking of HTTP configuration In fact SMS Machine makes an HTTP request to the web server and the script you set in HTTP page using default parameters Send Message This is the button to make the SMS Machine send a message and so it allows easy checking of the correct modem working of the SIM card and of the mobile ope
39. s except for the information stored in browser cache memory For this reason you have to logut and link the browser to the new address assigned to the SMS Machine HTTP PUSH Netmask It is the netmask of the network where you want to use SMS Machine HTTP PUSH Default value is 255 255 0 0 As said before changing the netmask you need to login once again Gateway It is the IP address of a server able to route on the outside network all the packets not addressed to local network machines This parameter must be configured only if SMS Machine HTTP PUSH needs to reach a server outside from the local network e g on the Internet DNS It is the IP address of an effective DNS server This parameter must be configured only if server names are used instead of their IP address New password Repeat password These two fields have to be filled with the same string if it is desired to change SMS Machine HTTP PUSH access password If you forget this password you may follow the procedure described ahead for factory configuration restoring GSM This page allows configuring the Service Centre of the Mobile Operator to which belongs the SIM card used in the SMS Machine HTTP PUSH SIM card parameters configuration O HTTP Aavanced Message service center number Current Status 393492000200 O Configuration Test Predefined Italian mobile operators service centers Ww EN an vi Save Logout Release 1
40. the SIM you will choose it during configuration 2 A good GSM field level Before inserting the SIM card into SMS Machine HTTP PUSH you should use it with an ordinary mobile phone to verify that there is a good GSM field level where you will place the antenna The provided antenna can be positioned up to 2 5m far from the device so a better signal coverage can be obtained for a regular operation 3 Ethernet connection SMS Machine HTTP PUSH has a 10Mbit Ethernet socket to be connected on your LAN by an Hub Switch Please be sure that the Hub Switch socket is 10Mbit or 10 100Mbit Beyond physical connection to your network you need some information about it IP addresses Netmask Gateway DNS Server to configure SMS Machine HTTP PUSH So you may need to refer to your network administrator to collect this kind of information 4 A220 VAC power supply SIM card insertion To protect SIM card by accidental removing from the modem during operation its socket is inside SMS Machine HTTP PUSH aluminium case So to reach SIM card socket unlock the four screws using a crossed screwdriver and make the case cover slide ahead as you can see in the next figure SMS Machine HTTP PUSH case opening Once you opened the case find the GSM modem and insert the SIM card in its socket with the golden electric contacts turned towards the bottom and the cut corner ahead as showed by the sketch on the modem itself or by the next figure SMS Machine HT
41. the received SMS data toward the destination script In fact it is not ensured that the transaction is successful at the first attempt for example for a temporary unavailability of the server network traffic or simply because the script is not correctly configured In these cases the machine SMS Machine HTTP Wap Push User Manual Page 20 SMS Machine 2009 Area SX srl will discard the SMS message after the number of attempts configured and passes to manage next message On the contrary if this parameter is set to 0 the default value then the SMS Machine HTTP PUSH will never discard the message and try forever the transmission to the reception script So it is evident that in the first condition an higher speed in transmission of received SMS to the script can be obtained but the risk is SMS messages lost in case of discarding for any transient reason of failed attempts In the second case no message will be lost but the communication could slow down in difficult condition for example for exceeding network traffic An extreme case is the definite unavailability of the reception script that can cause the overflow of SIM card memory reserved for received SMS Then the Service Centre of the Mobile Operator will cease new delivery attempts waiting for SIM card memory emptying by the SMS Machine HTTP PUSH and store the exceeding messages for hours as configured in mobile phone settings typically from 24h to 72h Timeout wa
42. to e teleallarme oppure in combinazione con sistemi SMS EE pi complessi controllandolo attraverso l interfaccia seriale RS232 d ULTIME PRODOTTI Server Patrol A breve sul sito Area SX una panoramica pi estesa ed alcuni di utilizzo Fax Sentinel Per un dettaglio tecnico sul prodotto vedi la scheda tecnica EZ10 UW SMS Machine HTTP DEE GSM G S con interprete Pytho Sen SMS HTTP con PHP Jemen SMS HTTP con ASP Paxev Sistema di telecontrollo GSM GPRS GPS con interprete Python Display 20x4 Bianco SMS HTTP con VB SMS Manager e I iT Dotata di 2 ingressi optoisolati 2 uscite a rele seriale RS232 batteria di A e Ma backup 2 connettori di espansione host per convertitore seriale pori gt Hardware 7 muatten tasti ad Fine internet http www areasx com REI con keypad da sei Una nuova idea di telecontrollo un sistema semplice aperto e potente da poter 71 tasti ed interfaccia programmare senza sforzo tramite una semplice porta seriale la nuova SXPY tutto USB SERDE SAO ua a sara EE EH It s also possible to contact us at the following Phone 39 06 57 17 26 90 and 39 06 57 17 26 79 Fax 39 06 57 17 26 95 E mail info areasx com SMS Machine HTTP Wap Push User Manual Page 2 SMS Machine 2009 Area SX srl Warnings Contents and copyright Information belonging to this manual may be changed or updated without any warning
43. tring without any HTML tag but however displayable by a browser that contains errno parameter and its description which values are e errno 0 amp desc Configuration_Accepted Configuration change OK e errno 1 amp desc Access denied wrong password Operation status request SMS Machine supports also a cgi script to retrieve information about its general operating status at the following URL http smsmachine_address getstatus cgi This request must be carried out in HTTP POST mode sending the following parameter e Pwd password that allows SMS Machine to accept the transaction SMS Machine HTTP Wap Push User Manual Page 32 SMS Machine 2009 Area SX srl SMS Machine answers with a string without any HTML tag but however displayable by a browser that is composed by the concatenation of pairs parameter name value Parameters are e errno 0 amp desc Configuration Sent Communication OK or errno 1 amp desc Access denied wrong password e GsmFieldLevel GSM field level in dBm e LastGsmError modem status or last revealed error e TxGsmCounter number of SMS in transmission queued into the modem e RxGsmCounter number of SMS in reception received by the modem e TxServerCounter number of SMS in transmission queued into the processor e RxServerCounter number of SMS in reception forwarded to the server e ServerStatus status of the reception script server e Fversion firmware version e FailedCounter number of SM
44. ve Finally if this parameter is set to other values then you have to know first that just this port number is used by the application running on the mobile terminal typically J2ME and responsible for management of SMS messages sent with this format Logout It is the configuration interface exit and then the main page will be shown SMS Machine HTTP Wap Push User Manual Page 25 SMS Machine 2009 Area SX srl Factory configuration restoring Whenever you want it is possible to restore SMS Machine HTTP PUSH factory default configuration This operation may be useful when it is impossible to access to SMS Machine HTTP PUSH because for example you forgot IP address or password In order to complete this operation follow this procedure e Turn off SMS Machine HTTP PUSH e Find the reset button on the rear panel as shown in next figure e Press this button and keep on pressing it while you turn on SMS Machine HTTP PUSH again e Keep on pressing the button and wait until ERR and L2 LEDs are lit at the same time This way SMS Machine HTTP PUSH will restart with all parameters default configuration in particular you will access it again using IP address 192 168 0 101 netmask 255 255 0 0 and password SMS1234 Button for factory default configuration restoring SMS Machine HTTP Wap Push User Manual Page 26 SMS Machine 2009 Area SX srl Technical characteristics Performances e Transmission top speed 300
Download Pdf Manuals
Related Search