Model 935 Quad Constant-Fraction 200-MHz Discriminator
Contents
1. inputs can be individually selected to be either coincidence or anti coincidence via DIP switches on the printed circuit board Each channel ran also be programmed for NIM bins incorporating that signal to ignore or respond to the slow bin gate signal on pin 36 of the power connector 2 SPECIFICATIONS The Model 935 contains four independent and identical constant fraction discriminators Except where stated otherwise the descriptions and specifications are given for an individual channel and apply to each of the four channels 2 1 PERFORMANCE WALK Guaranteed lt 50 ps typically lt 25 ps over a 100 1 dynamic range Measured under the following conditions input pulse amplitude range from 50 mV to 5 V rise time lt 1 ns pulse width 10 ns external shaping delay approximately 1 6 ns 33 cm or 13 in internal offset delay enabled threshold approximately 20 mV CONSTANT FRACTION 20 PULSE PAIR RESOLUTION lt 5 ns in the updating mode lt 7 ns in the blocking mode INPUT OUTPUT RATE Operates at burst rates gt 200 MHZ in the updating mode and gt 150 MHZ in the blocking mode TRANSMISSION DELAY Typically lt 13 ns with 1 6 ns external delay OPERATING TEMPERATURE RANGE 0 to 50 C THRESHOLD TEMPERATURE SENSITIVITY lt 0 01 C from 0 to 50 C Threshold referenced to the 12 V supply level supplied by the NIM bin TRANSMISSION DELAY TEMPERATURE SENSITIVITY lt 10 ps C from 0 to 50 C 2 2 CONT2. CF Monitor signal can be observed on a fast oscilloscope bandwidth gt 300 MHZ which is terminated in 50 Q and triggered internally The Monitor signal represents the attenuated undelayed portion of the constant fraction signal with no delayed signal subtracted from it The addition of the appropriate external CF Shaping Delay tyexterna Causes the resulting bipolar signal at the CF Monitor to cross the baseline at the peak of the attenuated undelayed signal When using the internal offset delay i e jumper W1 removed a useful formula for the initial trial selection of the CF Shaping Delay is taexternay T 1 0 ns W1 removed 3 3 where T is the time for the leading edge of the pulse to rise from 20 of maximum amplitude to maximum amplitude The 20 number corresponds to the 20 triggering fraction designed into the Model 935 With jumper W1 in place i e when not using the internal offset delay a useful formula for the initial trial selection of the CF Shaping Delay is tacexternay T 0 7 ns W1 in place 3 4 In normal operation jumper W1 is removed and placed in the storage area at the rear of the PWB This setting will work properly for all input signals The Model 935 is shipped with jumper W1 in the storage area For input signals having rise times greater than 2 ns jumper W1 can be used to short the internal offset delay allowing for shorter external CF Shaping Delays 3 7 WALK SETTING The Walk adj
3. and its output is applied to the transformer XFMR The second output of the Splitter is delayed by the external CF Shaping Delay and applied to the second input to the XFMR The XFMR output is a bipolar shaped signal whose zero crossing time is used to derive the Model 935 output This signal is amplified by the constant fraction amplifier CFA prior to being connected to the zero crossing gate Gl The LEAD has an adjustable threshold ranging from 20 mV to 1 V that determines the minimum input signal amplitude that is required to produce an output pulse from the Model 935 If the input signal exceeds the LEAD threshold that comparator produces an output pulse that arms zero crossing gate G1 The timing logic signal from gate G1 triggers a fast one shot comprised of an ECL type D master slave flip flop FF1 and a stretcher circuit All gating input signals are ORed by G2 and applied to the D input of FF1 One output of FF1 drives A2 which controls the front panel event LED The other output of FF1 drives the stretcher circuit which controls the width of the output signals The output driver circuit provides a fast voltage output signal that is capable of driving three 50 O loads simultaneously with NIM standard negative fast logic pulses The output signals are either updating or blocking depending on the setting of PWB jumper W2 The dc power requirements are shown in the specifications in Section 2 The power levels are
4. anticoincidence mode for the individual channel s response to the rear panel gate input VETO YES NO A printed wiring board DIP switch selects whether or not an individual channel will respond to the front panel VETO input BIN GATE YES NO A printed wiring board DIP switch selects whether or not an individual channel will respond to the bin gate signal INTERNAL OFFSET DELAY WI Printed wiring board jumper W1 is normally omitted to enable the 1 7 ns internal offset delay This delay compensates for internal delays and makes it possible to implement the very short shaping delays required with 1 ns input pulse widths With jumper W1 installed the minimum shaping delay is limited by a 0 7 ns internal contribution With W1 omitted the internal delay contribution is effectively 1 0 ns The Model 935 is shipped from the factory with the W1 jumper omitted Spare jumpers for this position are located in the storage area towards the rear of the module UPDATING BLOCKING MODE W2 The printed wiring board jumper W2 selects either the updating mode U or the blocking mode B for the output pulse widths In the blocking mode a second input pulse will generate no output pulse if it arrives within the output pulse width W caused by a previous input pulse In the updating mode a second input pulse arriving within the output pulse width W from a previous pulse will extend the output pulse from the time of arrival by a length W The Model 9
5. panel The length of cable determines the amount of external signal delay that is added to the internal delay to constitute the total constant fraction shaping delay Since the Model 935 is equipped with a jumper selectable internal offset delay the external CF shaping delay will depend on the position of internal jumper W1 With jumper W1 removed placed in the storage area at the rear of the PWB the total constant fraction shaping delay tytotay is approximated by tacrotay taexternay 1 0 ns Wi removed 3 1 tacrotay taexternay 0 7 ns W1 in place 3 2 The primary usage of the Model 935 is expected to be in fast timing or counting experiments with scintillators and photomultiplier tubes PMTs and Silicon Surface Barrier Detectors In these applications the CF Shaping Delay taroa is selected so that the zero crossing of the bipolar timing signal occurs just as the peak of the attenuated undelayed portion of the CF signal has reached its maximum amplitude Thus the zero crossing occurs at the same fraction of the input pulse height regardless of the amplitude of the input signal Selection of the CF Shaping Delay for best timing performance with a given scintillator and PMT is usually accomplished experimentally The randomly generated signals from the anode of the PMT are applied to the input of one channel of the discriminator Each of the two CF Delay connectors should be terminated with a 50 Q terminator The
6. the output signal amplitude from the PMT In general the high voltage should be set sufficiently high to ensure a large signal input to the CFD However the high voltage should not be set so high as to cause the onset of saturation in the PMT The final adjustment of the high voltage is acompromise that can best be determined experimentally 4 2 THRESHOLD ADJUSTMENT The Model 935 will produce an output signal each time the input signal crosses the threshold Setting the threshold is equivalent to setting the lowest energy of interest While it is possible to set the threshold using an oscilloscope a far more accurate method is to use the actual detector a radioactive source and an MCA gated by the Model 935 A Gate and Delay Generator is used to convert the Model 935 output to a signal suitable for gating the MCA To adjust the threshold level measure the dc voltage from the front panel Threshold monitor test point to ground for the active channel The Threshold monitor test point is located to the left of the threshold potentiometer on the front panel A convenient ground test point is located at the Fig 3 a Anode signal from PMT and scintillator b the Model 935 CF Monitor signal showing proper walk adjustment and c the Model 935 CF Monitor signal showing improper walk adjustment See text for discussion DYNODE Fig 4 A Simple Timing System bottom of the front panel to the right of the Veto Inpu
7. unused channels 3 5 GATING Each channel of the Model 935 can be externally gated by one of three conditions A front panel Veto input can block the output Each channel can be separately gated by rear panel Gate inputs A NIM bin signal the B bin Gate operating through pin 36 of the power connector in the NIM bin can inhibit an output providing that the rear panel B Gate switch is set to On The gating conditions for each channel of the Model 935 are controlled by PWB DIP switches The Veto input can be selected as either Yes or No the Gate input can be selected as either Coincidence or Anticoincidence and the B Gate can be selected as either Yes or No For proper gating operation certain timing conditions must be satisfied between the leading edge of the input signal and the gating signal When using the front panel fast Veto input its leading edge should precede the input signal by 3 ns and its width should be equal to the CF shaping delay plus 5 ns When using the rear panel Gate input its leading edge should precede the input signal by 1 ns and its width should be equal to the CF shaping delay plus 5 ns The B bin Gate signal is a slow logic signal and it must overlap the input signal to be effective 3 6 CF SHAPING DELAY CABLE SELECTION The CF shaping delay for each channel is adjusted by selecting an appropriate length of 50 Q coaxial cable and adding it between the two Delay DLY LEMO connectors on the front
8. 35 is shipped from the factory in the updating mode OUTPUT PULSE WIDTH RANGE W3 The printed wiring board jumper W3 selects the range of output width adjustment as listed in Table 1 The Model 935 is shipped from the factory with the W3 jumper omitted Spare jumpers for this position are located in the storage area toward the rear of the module 2 3 INPUTS IN1 IN2 IN3 or INA A front panel LEMO connector input on each channel accepts the fast linear signal from a detector for constant fraction timing Linear range from 0 to 10 V Signal input impedance 50Q dc coupled input protected with diode clamps at 10 V Input reflections lt 10 for input rise times gt 2 ns GATE INPUTS 1 2 3 or 4 A rear panel BNC connector for each channel accepts a negative fast NIM logic signal to gate the respective constant fraction timing output Coincidence or anticoincidence gating is selected by a printed wiring board DIP switch See GATE COIN ANTI Inputimpedance 500 For proper gating operation the leading edge of the GATE INPUT should precede the IN1 IN2 IN3 or IN4 signal by 1 ns and have a width equal to the CF Shaping Delay plus 5 ns VETO A single front panel LEMO connector accepts NIM negative fast logic pulses to inhibit the timing outputs on all the channels chosen with the VETO YES NO switch Input impedance 500 For proper FAST VETO operation the leading edge of the VETO signal must precede the IN1 IN2 IN3 or IN
9. 4 signal by 3 ns and have a width equal to the CF Shaping Delay plus 5 ns BIN GATE A slow master gate signal enabled by the rear panel B GATE ON OFF switch permits gating off the timing outputs when the Model 935 is installed in a bin that provides a bin gate signal on pin 36 of the NIM power connector Clamping pin 36 to ground from 5 V inhibits operation of all channels selected by the BIN GATE YES NO switch 2 4 OUTPUTS CF SHAPING DELAY DLY A front panel pair of LEMO connectors for selecting the required constant fraction shaping delay A 50 O cable is required For triggering at a 20 fraction the length of the shaping delay is approximately equal to the time taken for the input pulse to rise from 20 of its full amplitude to full amplitude CF MONITOR M Permits observation of the constant fraction shaped signal through a LEMO connector on the front panel Output impedance 50 O ac coupled The monitor output is attenuated by a factor of approximately 5 with respect to the input when driving a terminated 50 Q cable OUT Three bridged updating or blocking fast negative NIM output signals furnished through front panel LEMO connectors mark the CF zero crossing time Amplitude 800 mV on 50 0 load Each output connector has its own 50 0 resistor in series with the common output driver GND Front panel test point provides a convenient ground connection for test probes EVENT OCCURRED LED Front panel LED for each ch
10. 6 V 6 V 12 V 1 2 V and 24 V and they are all obtained directly from the bin power supply 10 Veto FP gem Gate RP ay Bin Gate PERLE THRESHOLD Input YT CF Shaping Delay CF Mon o lt AN A1 HCF0411 WALK Fig 5 Simplified Block Diagram of One Section of the Model 935 LED yo WIDTH Outputs D Q O FFA gt amp STRETCH DRIVER o R A2 HST0107 A3 H000107 O w3 Q O L s TL i w2 x Update 3945 Blocking 6 MAINTENANCE 6 1 CALIBRATION Most adjustments to the Model 935 are made via front panel controls The only internal adjustment is the Threshold Cal potentiometer R Should recalibration be required connect a 50 mV 20 ns wide signal to the input of the section being adjusted Adjust the front panel Threshold potentiometer such that the front panel Threshold Test Point reads 500 mV Adjust the Threshold Cal potentiometer so that the Model 935 output half fires 6 2 TYPICAL DC VOLTAGES All voltages listed on the schematic drawing are measured with respect to ground with the Threshold and Width controls set at minimum and the Walk set at 1 5 mV 6 3 FACTORY SERVICE This instrument can be returned to the ORTEC factory for service and repair at a nominal cost The ORTEC standard procedure for repair ensures the same quality control and checkout that are used for a new instrument Always contact Customer Services at ORTEC before sending an instrument fo
11. Model 935 Quad Constant Fraction 200 MHz Discriminator Operating and Service Manual U S Patent No 4 179 644 Printed in U S A ORTEC Part No 753770 0503 Manual Revision H Advanced Measurement Technology Inc a k a ORTEC a subsidiary of AMETEK Inc WARRANTY ORTEC warrants that the items will be delivered free from defects in material or workmanship ORTEC makes no other warranties express or implied and specifically NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ORTEC s exclusive liability is limited to repairing or replacing at ORTEC s option items found by ORTEC to be defective in workmanship or materials within one year from the date of delivery ORTEC s liability on any claim of any kind including negligence loss or damages arising out of connected with or from the performance or breach thereof or from the manufacture sale delivery resale repair or use of any item or services covered by this agreement or purchase order shall in no case exceed the price allocable to the item or service furnished or any part thereof that gives rise to the claim In the event ORTEC fails to manufacture or deliver items called for in this agreement or purchase order ORTEC s exclusive liability and buyer s exclusive remedy shall be release of the buyer from the obligation to pay the purchase price Inno event shall ORTEC be liable for special or consequential damages Quality Control Before being appr
12. ROLS THRESHOLD T A front panel 20 turn screwdriver adjustment for each discriminator channel sets the minimum pulse amplitude that will produce a timing output Variable from 20 to 1000 mV A front panel test point located to the left of the threshold adjustment monitors the discriminator threshold setting The test point voltage is 10x the actual threshold setting Output impedance lt 2 kQ WALK ADJUSTMENT Z A front panel 20 turn screwdriver adjustment for fine tuning the zero crossing discriminator threshold to achieve minimum walk Adjustable over a 15 mV range A front panel test point located to left of the walk adjustment monitors the actual setting of the zero crossing discriminator Output impedance 1 kQ OUTPUT WIDTH W A front panel 20 turn screwdriver adjustment for each discriminator channel sets the width of the three output logic pulses The range of width adjustment depends on the positions of jumpers W2 and W3 Table 1 The Dependence of the Output Pulse Width Range on W2 and W3 Jumper Positions w3 Output Pulse Width Adjustment Jumper Range Position W2 U W2 B Updating Blocking lt 4 to gt 100 ns lt 5 to gt 100 ns lt 4 to gt 200 ns lt 5 to gt 200 ns Not functional lt 30 ns to gt 400 ns B GATE ON OFF Rear panel switch turns the Bin Gate on or off for all channels programmed to accept the Bin Gate GATE COIN ANTI A printed wiring board DIP switch selects either the coincidence or
13. annel indicates that an output signal has occurred 2 5 ELECTRICAL AND MECHANICAL POWER REQUIREMENTS The Model 935 derives its power from a NIM bin power supply Required dc voltages and currents are 12 V at 33 mA 6 V at 225 mA 6V at 1400 mA 12V at 169 mA 24 V at 55 mA WEIGHT Net 1 1 kg 2 6 Ib Shipping 2 0 kg 4 4 lb DIMENSIONS NIM standard single width module 3 43 x 22 13 cm 1 35 x 8 714 in per TID 20893 Rev 3 INSTALLATION 3 1 GENERAL The Model 935 power requirements must be furnished from a NIM standard bin and power supply that includes 6 V power distribution such as the ORTEC 4001C 4002E 4001C 4002D or 4001 A 4002D NIM Bins Power Supplies The bin and power supply in which the Model 935 will normally be operated is designed for relay rack mounting If the equipment is rack mounted be sure that there is adequate ventilation to prevent any localized heating in the Model 935 The temperature of equipment mounted in racks can easily exceed the maximum limit of 50 C 323 K unless precautions are taken 3 2 CONNECTION TO POWER Due to the very high speed electronic components used in the Model 935 to achieve its excellent performance the Model 935 exceeds the normal fair share of power per slot of normal NIM power supplies AS many as eight Model 935s a total of 32 channels can be operated in a ORTEC 4002C 4002E NIM Bin Power Supply To be sure of proper operation check the de voltage lev
14. e 4 3 2 CONNECTION TO POWER 1 nennen een ee een 4 3 3 INPUT CONNECTIONS ooo 4 3 4 OUTPUT CONNECTIONS tai essen ee a ein een pa bead ab ner 4 Bis GATING atra er ne ber er u een ida 5 3 6 CF SHAPING DELAY CABLE SELECTION 2 222220 nennen ernennen een nn 5 3 7 WALK SETTING Ze Di Dein ni 6 4 OPERATING INSTRUCTIONS 22n2neeene ernennen nennen nenne een 6 41 GENERAL rn a en nee en ge een 6 4 2 THRESHOLD ADJUSTMENT 0 eect een nn 6 4 3 OUTPUT WIDTH ADJUSTMENT occ 8 4 4 CONSTANT FRACTION SHAPING DELAY ADJUSTMENT 0 0 00 eee eee eee 8 4 5 WALK ADJUSTMENT 22 32 teren unten red wise are ne 8 4 6 GATING ADJUSTMENTS 44 24 22 eras ees by nes de coy dela ped tle an o fe 9 5 THEORY OF OPERATION iensor ee ae i abd ek ee 9 6 MAINTENANCE 22 22 2 nen re weak ee a 10 681 CALIBRATION oido S248 arzt 2m er ee ners IE alien 10 6 2 TYPICAL DC VOLTAGES skin ee eek 10 6 3 FACTORY SERVICE ugt tapes ea e oes bee e ped le dae een 10 SAFETY INSTRUCTIONS AND SYMBOLS This manual contains up to three levels of safety instructions that must be observed in order to avoid personal injury and or damage to equipment or other property These are DANGER Indicates a hazard that could result in death or serious bodily harm if the safety instruction is not observed WARNING Indicates a hazard that could result in bodily harm if the safety instruction is not observed CAUTION Indicates a hazard that could
15. els of the power supply after all modules have been installed in the bin ORTEC bins and power supplies include convenient test points on the power supply control panel to permit monitoring these levels 3 3 INPUT CONNECTIONS Each discriminator channel includes an input connector on the front panel that is terminated internally in 500 Connect the source of negative input signals to this connector through a 500 coaxial cable and a mating LEMO connector Any of the four channels can be provided with an input signal and will operate independently from all other channels 3 4 OUTPUT CONNECTIONS There are three output connectors for each channel These connectors furnish three identical simultaneous negative NIM logic signals for each input pulse that exceeds the adjusted threshold level The output pulse width can be adjusted by the front panel W control associated with that channel When operating in the updating mode the range of width adjustment can be increased by adding a PWB jumper to the S pins at W3 When operating in the blocking mode the range of width adjustment can be increased by adding jumpers to either or both the S and L pins at W3 Each output connection should be furnished through a mating LEMO connector and a 50 0 coaxial cable to a 50 0 load impedance For best results terminate all unused output connectors in each active channel with a 50 Q terminator on the front panel Termination is not necessary for
16. ferent Units See Walk Specifications for Measurement Conditions The extremely short pulses from microchannel plate multipliers and ultra fast photomultiplier tubes require very short constant fraction shaping delays To accommodate these detectors the Model 935 incorporates a selectable compensation for the inherent internal delay The Model 935 includes a number of controls which considerably broaden its utility The threshold discriminator is useful for rejecting low level noise A front panel test point permits precise measurement of its setting in the range from 20 to 1 000 mV Each channel provides three bridged timing outputs These are standard fast negative NIM outputs The outputs can be selected to have either updating or blocking characteristics The updating mode is useful for reducing dead time in overlap coincidence experiments The blocking mode simultaneously minimizes multiple triggering and dead time on scintillators with long decay times The output pulse width is adjustable from lt 4 ns to gt 200 ns in the updating mode and from lt 5 ns to gt 1 us in the blocking mode The pulse pair resolution is lt 5 ns at minimum pulse width in the updating mode Switches on the printed circuit board allow selection of which channels will respond to the front panel fast veto input Additional fast gating capability is provided by individual gate inputs for each channel on the rear panel The mode of these separate gate
17. ive to the Input signal blocks the output of that channel In the Coincidence mode a Gate input enables the output of that channel If no Gate input is to be used place the DIP switch in the Anticoincidence position The middle set of DIP switches controls the front panel fast Veto input With the DIP switch corresponding to a given channel in the On position the fast Veto signal can block or veto the output of that channel providing that the timing conditions of the fast Veto input relative to the Input are satisfied The lowest set of DIP switches controls the bin gate input The bin gate DIP switches are effective only K the rear panel B Gate switch is in the On position With the B Gate switch in the On position and the DIP switch in the On position a bin gate blocks the output of the corresponding channel provided that the timing conditions relative to the input signal are satisfied The timing conditions for all the gating inputs are described in Section 3 5 5 THEORY OF OPERATION Figure 5 is a simplified block diagram of the instrument that can be used as a reference to describe how it operates An input of 0 to 10 V amplitude starts at time zero and is applied to the 50 0 Splitter One output of the Splitter is delayed by the internal offset delay DL1 before it is applied to the leading edge arming discriminator LEAD and the CF attenuator ATTN The ATTN circuit sets the constant fraction attenuation factor of f 0 2
18. lk adjustment is best accomplished by optimizing the symmetry and minimizing the width of the coincidence peak in the time spectrum see Section 4 4 OPERATING INSTRUCTIONS 4 1 GENERAL The actual timing performance of a timing system depends on many variables The type of detector and the energy range of interest are two important system variables that are independent of the electronics In general detectors having fast rise time signals and higher energies give the best timing performance A simple timing system is shown in Figure 4 This system consists of two detectors each with their own high voltage supply two Model 935 CFDs a Delay unit for timing calibration and signal offset a Time to Amplitude Converter TAC and a multichannel analyzer MCA Also shown is a Preamplifier PA a spectroscopy amplifier Amp and a Gate and Delay Generator GDG used for energy calibration The detectors shown in Figure 4 consist of fast scintillators mounted on fast photomultiplier tubes PMTs Each PMT is connected to a PMT Base for distribution of the high voltage Care must be taken in preparing and mounting the scintillator to ensure very efficient coupling between the scintillator and the PMT The high voltage setting for the PMT depends on the type of PMT and the manufacturer of the PMT should be consulted The gain of the PMT depends directly on the value of the high voltage and provides a convenient method for adjusting
19. m with the shipper Instruments not in warranty should follow the same procedure and ORTEC will provide a quotation Damage in Transit Shipments should be examined immediately upon receipt for evidence of external or concealed damage The carrier making delivery should be notified immediately of any such damage since the carrier is normally liable for damage in shipment Packing materials waybills and other such documentation should be preserved in order to establish claims After such notification to the carrier please notify ORTEC of the circumstances so that assistance can be provided in making damage claims and in providing replacement equipment if necessary Copyright 2003 Advanced Measurement Technology Inc All rights reserved ORTEC is a registered trademark of Advanced Measurement Technology Inc All other trademarks used herein are the property of their respective owners CONTENTS SAFETY INSTRUCTIONS AND SYMBOLS 00 cc eect tenes iv SAFETY WARNINGS AND CLEANING INSTRUCTIONS 0 0 00 cece v 1 DESCRIPTION A zer as a E a a hee ade Se ht det ne 1 2 SPECIFICATIONS coord a een nn Boe ea aS 2 21 PERFORMANCE corra ias rs ni nr Rn Leer Ba 2 2 2 CONTROLS a urn Ze A Re a es 2 2 32 INRUTES Asse sn A en Den 3 2 4 OUTPUTS spread eee a 3 2 5 ELECTRICAL AND MECHANICAL oooccccococ nennen ernennen een 4 3 INSTALLATION 2 22 23 gt seca p np ee Der ar aan Rp u ne 4 33 GENERAL costat a ee ctl hie BP ae a e
20. mum amplitude to maximum amplitude Simultaneously the prompt input signal is attenuated to 20 of its original amplitude This attenuated signal is added to the delayed and inverted signal to form a bipolar signal with a zero crossing The zero crossing occurs at the time when the inverted and delayed input signal has risen to 20 of its maximum amplitude The zero crossing discriminator in the Model 935 detects this point and generates the corresponding timing output pulse Walk is the systematic error in detecting the time for the 20 fraction as a function of input pulse amplitude Minimizing walk is important when a wide range of pulse amplitudes must be used because walk contributes to the time resolution The Model 935 uses a patented transformer technique for constant fraction shaping to achieve the exceptionally wide bandwidth essential for processing input signals with sub nanosecond rise times As shown in Fig 1 this results in a walk guaranteed lt 50 ps and typically lt 25 ps overa 00 1 dynamic range of input pulse amplitudes The patented shaping technique also provides a zero crossing monitor output that facilitates quick and accurate walk adjustment because it displays the full input signal amplitude range in F lt 50 ps Guaranteed Walk ps o Actual Walk measured on Four Different Units 0 02 0 05 9 1 0 2 0 5 10 20 so Signal Amplitude volta Fig 1 Actual Walk Measured on Four Dif
21. oved for shipment each ORTEC instrument must pass a stringent set of quality control tests designed to expose any flaws in materials or workmanship Permanent records of these tests are maintained for use in warranty repair and as a source of statistical information for design improvements Repair Service If it becomes necessary to return this instrument for repair it is essential that Customer Services be contacted in advance of its return so that a Return Authorization Number can be assigned to the unit Also ORTEC must be informed either in writing by telephone 865 482 4411 or by facsimile transmission 865 483 2133 of the nature of the fault of the instrument being returned and of the model serial and revision Rev on rear panel numbers Failure to do so may cause unnecessary delays in getting the unit repaired The ORTEC standard procedure requires that instruments returned for repair pass the same quality control tests that are used for new production instruments Instruments that are returned should be packed so that they will withstand normal transit handling and must be shipped PREPAID via Air Parcel Post or United Parcel Service to the designated ORTEC repair center The address label and the package should include the Return Authorization Number assigned Instruments being returned that are damaged in transit due to inadequate packing will be repaired at the sender s expense and it will be the sender s responsibility to make clai
22. r repair to obtain shipping instructions and so that the required Return Authorization Number can be assigned to the unit This number should be written on the address label and on the package Table 2 Bin Module Connector Pin Assignments For Standard Nuclear Instrument Modules per DOE ER 0457T Pin Function 1 43V 2 3V 3 Spare bus 4 Reserved bus 5 Coaxial 6 Coaxial 7 Coaxial 8 200 V dc 9 Spare 10 6V 11 6V 12 Reserved bus 13 Spare 14 Spare 15 Reserved 16 12V 17 12V 18 Spare bus 19 Reserved bus 20 Spare 21 Spare 22 Reserved Function Reserved Reserved Reserved Spare Spare 24 V 24 V Spare bus Spare Spare 117 V ac hot Power return ground Reset Scaler Gate Reset Auxiliary Coaxial Coaxial Coaxial 117 V ac neutral High quality ground Ground guide pin Pins marked are installed and wired in ORTEC s 4001A and 4001C Modular System Bins 12
23. result in property damage if the safety instruction is not observed Please read all safety instructions carefully and make sure you understand them fully before attempting to use this product In addition the following symbol may appear on the product N ATTENTION Refer to Manual AN DANGER High Voltage Please read all safety instructions carefully and make sure you understand them fully before attempting to use this product SAFETY WARNINGS AND CLEANING INSTRUCTIONS DANGER Opening the cover of this instrument is likely to expose dangerous voltages Disconnect the instrument from all voltage sources while it is being opened WARNING Using this instrument in a manner not specified by the manufacturer may impair the protection provided by the instrument Cleaning Instructions To clean the instrument exterior e Unplug the instrument from the ac power supply e Remove loose dust on the outside of the instrument with a lint free cloth e Remove remaining dirt with a lint free cloth dampened in a general purpose detergent and water solution Do not use abrasive cleaners CAUTION To prevent moisture inside of the instrument during external cleaning use only enough liquid to dampen the cloth or applicator e Allow the instrument to dry completely before reconnecting it to the power source vi ORTEC MODEL 935 QUAD 200 MHz CONSTANT FRACTION DISCRIMINATOR 1 DESCRIPTION The Model 935 Quad 200 MHz Constant Frac
24. t connector The nominal range of voltages at the Threshold test point is 200 mV to 10 V corresponding to the actual threshold which is 10 of the test point voltage Use a screwdriver to set the threshold level with the control marked T 4 3 OUTPUT WIDTH ADJUSTMENT To adjust the output width provide an input pulse that exceeds the adjusted threshold at a rate less than 0 5 MHZ and observe the width of an output pulse from any of the three output connectors Terminate the other output connectors in 50 Q Use a screwdriver to set the control marked W for the output width in the active channel When operating in the Updating mode the output width can be adjusted from lt 4 ns to gt 100 ns Adding a PWB jumper to the S position of W3 changes the range of adjustment to gt 200 ns When operating in the blocking mode an additional jumper can be added to the L position of W3 increasing the Blocking output width to gt 1000 ns 4 4 CONSTANT FRACTION SHAPING DELAY ADJUSTMENT Selection of the initial value for the CF Shaping Delay is described in Section 3 6 For input signals SCINTILLATORS DYNODE To MCA To MCA Gate Input Signal Used to Calibrate the 935 Threshoid 3945 having widths approaching 1 ns it is necessary to fine tune the CF Shaping Delay to achieve optimum performance The optimum value is determined for a given detector using the timing system shown in Figure 4 Repeated measurements of timing resol
25. tion Discriminator incorporates four separate and independently adjustable timing discriminators ina single width NIM module Except where indicated otherwise the descriptions and specifications apply to each of the four channels in the module The ability of the Model 935 to provide constant fraction timing on fast negative polarity signals as narrow as 1 ns FWHM makes it ideal for use with microchannel plates fast photomultiplier tubes fast scintillators and fast silicon detectors The exceptionally low walk delivered by the Model 935 is vital in achieving the excellent time resolution inherent in these fast detectors over a wide dynamic range of pulse amplitudes The Model 935 can also be used with scintillators such as Nal TI which have long decay times To prevent multiple triggering on the long decay times the width of the blocking output can be adjusted up to 1 us in duration The Model 935 uses the constant fraction timing technique to select a timing point on each input pulse that is independent of pulse amplitude When properly adjusted the generation of the output logic pulse corresponds to the point on the leading edge of the input pulse where the input pulse has risen to 20 of its maximum amplitude To achieve this constant fraction triggering the input pulse is inverted and delayed The delay time is selected by an external delay cable DLY to be equal to the time taken for the input pulse to rise from 20 of maxi
26. ustment is a front panel 20 turn screwdriver adjusted potentiometer for each channel A Walk Monitor front panel test point is used to monitor the actual setting of the dc zero crossing adjustment A nominal value for this dc level is 1 5 mV but the optimal value is best determined experimentally Walk adjustment can be accomplished while observing the delayed CF Monitor signal on a fast oscilloscope bandwidth gt 300 MHZ which is triggered externally by the output signal of the Model 935 The Walk potentiometer Z should be adjusted so that the bipolar constant fraction signals for all amplitudes cross through the baseline at approximately the same time Figure 3 a shows the anode signals from a Hamamatsu 1332 PMT with a 12 9 cc BC418 truncated cone scintillator exposed to a Co source Figure 3 b shows the delayed CF Monitor signal triggered by the Model 935 output signal with the walk properly adjusted Adjusting the Walk potentiometer counterclockwise results in the waveform shown in Figure 3 c where the extra line near the baseline indicates leading edge timing Proper Walk adjustment can be achieved by adjusting the Walk potentiometer counter clockwise to obtain the waveform shown in Figure 3 c then turning the Walk adjustment clockwise to just eliminate the leading edge timing line An additional 1 to 2 turns clockwise should give the waveform in Figure 3 b and optimum walk adjustment The final optimization of the Wa
27. ution FWHM and FWHM are made as a function of CF Shaping Delay length to determine the optimum value of the CF Shaping Delay 4 5 WALK ADJUSTMENT To adjust the Walk characteristics connect the signal source to be used to the Input connector in the active channel and connect the signal from the constant fraction Monitor connector to a fast oscilloscope bandwidth greater than 300 MHZ through a 50 0 delay Select the CF Shaping Delay according to the information in Section 3 6 The constant fraction shaped signal can be observed on the oscilloscope triggered by an undelayed output signal from the active discriminator Adjust the Walk Z control which sets the zero crossing reference so that the bipolar constant fraction signals for all input amplitudes cross through the baseline at approximately the same time The adjacent test point can be used for resettability of the zero crossing reference Under most operating conditions the dc voltage level at the test point should be in the range from 1 0 mV to 2 0 mV Use a screwdriver to adjust the Z control 4 6 GATING ADJUSTMENTS The gating conditions for each channel of the Model 935 are set by PWB DIP switches located near the rear panel of the Model 935 The DIP switches located nearest the top of the module set the Gate input to operate in either the Anticoincidence mode or the Coincidence mode In the Anticoincidence mode a Gate input that satisfies the timing conditions relat
Download Pdf Manuals
Related Search