KIPFold 2000 User Guide
Contents
1. KIPFold 2000 User Guide KIPFold 2000 User Guide Safety Read these safety instructions completely before operating the folder and keep this manual for future reference close to the folder Carefully observe all warnings precautions and instructions on the folder or the ones described in the operating instructions In order to guarantee hazard free operations all maintenance and repairs are only to be carried out by trained personnel WARNING Indicates a potentially hazardous situation which if not avoided COULD result in death or serious injury Warning CAUTION Indicates a potentially hazardous situation which if not avoided MAY result in minor or moderate injury Maintenance and Modifications To avoid the risk of introducing hazards all modifications and maintenance activities are strictly reserved to properly qualified and trained service technicians In daily use any electrical equipment may be subject to parts wear and eventual failure In order to maintain safety and reliability the Customer Engineer hereafter called CE must perform regular maintenance inspections General Make sure that the folder is placed on a level horizontal surface of sufficient strength See the respective specifications sheet for the weight of the equipment Always use materials for the respective folder Materials not approved can cause faults in the folder Do not use the folder when it is emitting unusual sounds Re2. amp Switch on Please use only the power cable supplied with the folder 90 240 VAC 50 60Hz Do not use multi plug extension cords These cords will not stand the power consumption of printer and folder The power supply box is at the folder s right bottom side The main switch of the machine is next to the power cable connector Find the folders serial number on the rating plate next to the switch No part of this publication may be copied reproduced or distributed in any form without express written pemission from KIP 2013 KIP All references subject to change without notice 3 Error 22704 paper jam on Feed Table 1 press key for automatic release 2 of clear jam manually switch off power 3 restart The folder runs a self test of the system The standard start screen appears in the display if the test runs without any problem In case a problem has been detected during the self test the screen shows an error code Please refer to the Trouble Shooting for more information When Connected to the KIP Printer if this image is displayed on the Folder Screen the KIP Printer is controlling the folder in an online condition In order to put the folder into an Offline state at the touch screen of the printer select the Folder Offline button No part of this publication may be copied reproduced or distributed in any form without express wntten pemnnission from KIP 2013 KIP All r
3. the distributor who has been notified first must immediately take emergency measures to provide relief to affected persons and to prevent further damage 2 If a report of a serious accident has been received from a customer an onsite evaluation must be carried out quickly by an authorized person 3 To determine the cause of the accident conditions and materials must be recorded through direct on site checks in accordance with instructions 4 For reports and measures concerning serious accidents follow the regulations specified by the distributor Disclaimer Important These safeguards have been compiled to the best of our knowledge They are intended as a compact guide to the safe handling of the product We reserve the right to revise specification data sheets as new information becomes available It is the user s responsibility to determine the suitability of this information for the adoption of safety precautions as may be necessary It is the user s responsibility to ensure that the specification data sheets are the latest ones issued If and in so far as limitation of liability is permitted under the applicable laws we do not accept liability for any inaccuracy that may occur in this information No part of this publication may be copied reproduced or distributed in any form without express wntten pemnnission from KIP 2013 KIP All references subject to change without notice 2 KIPFold 2000 User Guide Power
4. the box to enable folding and using the dropdown arrow make sure that On is selected 6 Select the Desired Fold Packet KIP c7800 Printing Preferences 7 Select the OK button to set this Roll 1 841mm Bond 24 PREMIUM Roll 2 841mm Bond 204 STANDARD Roll 3 297mm Bond 248 PREMIUM Bypass Not Installed No part of this publication may be copied reproduced or distributed in any form without express wntten pemnnission from KIP 2013 KIP All references subject to change without notice 5 2 KIPFold 2000 User Guide KIP Autocad and Folding When using the KIP AutoCAD Driver to print and fold files follow these steps 1 From Within AutoCAD go to File and mhen Print e9 E ea Organize v Open v Share with v Burn New folder 2 A 2 Double click the installed KIP AutoCAD Ke Favorites Name Date modified Type WE Desktop Ji Plot Styles 2 8 20121 48PM_ File folder IB Downloads J PMP Files 2 3 2012 5 38PM File folder 47 Dropbox a Add A Plotter Wizard 6 2 2011 1 05PM_ Shortcut Adobe PDF pc3 2 3 2012 5 38PM AutoCAD Plotte Adobe PDFa pc3 2 3 2012 5 38 PM AutoCAD Plotte Te Default Windows System Printer pc3 3 3 2003 9 36 AM AutoCAD Plotte E Documents DWF6 ePlot pc3 1 12 2012 1 30PM AutoCAD Plotte adi hese DWFx ePlot XPS Compatible pc3 6 21 2007 12 17 AM AutoCAD Plotte E Pictures DWG To PDF pc3 10 22 2008 11 32 AutoCAD Plotte BE Videos KIP 510 SR 7900 pc3 3 20 2012 9 41 AM A
5. 2 Sensor errors on start up 84 Time out errors Location 4 Tab Applicator 41 03 No tape inside the unit or sensor is damaged 41 04 Jam close to the knife 41 05 No tab unit is installed No part of this publication may be copied reproduced or distributed in any form without express wntten pemnnission from KIP 2013 KIP All references subject to change without notice 299
6. FF or CF Data exchange failed to FF or CF Data transfer failed from FF or CF Data transfer failed to FF or CF No response from FF No response from CF Cover open Other communication errors 2i 2 2 2 3 2 4 Sheet management error No contact to FF during initialization No contact to CF during initialization No contact to modules during initialization Result codes FF result code is NIO FF result code is TIMEOUT FF result code is UNKNOWN CF result is NIO CF result is TIMEOUT CF result is UNKNOWN Error counting sheets 3 1 3 2 3 3 3 4 3 5 3 6 3 7 3 8 Too many sheets are in the folder No part of this publication may be copied reproduced or distributed in any form without express wntten pemission from KIP 2013 KIP All references subject to change without notice sIf KIPFold 2000 User Guide Start up and initialization errors 96 Time out while intiaizing FForCF S oe Timeoutwhie stating FForCF SSS 99 ParametertanstertoFForCFfaled OOO peracid EEPROM a Printer messages Location 2 Fan Folder errors Time out errors License errors 28 01 License error Missing high speed license speed is greater than 9 99 meter per l minute No part of this publication may be copied reproduced or distributed in any form without express wntten pemission from KIP 2013 KIP All references subject to change without notice ee KIPFold 2000 User Guide Location 3 Cross Folder errors 8
7. IP C7800 the Folder will be online 2 Select the Folder Offline button to put the folder into offline mode Printer Ready Toner Media E a0 om AD Bond 24 PREMIUM O D OEREN 2 AD Bond 20 STANDARD Belo OBB A3 Bond 24 PREMIUM P BeO C e Je 3 The following window will indicate the Folder is in the offline condition User Totals Type Media Status E a 4 With the folder in the offline state the user can now use the Folder touchscreen to determine folding output and manually feed pages into the folder and have them folded No part of this publication may be copied reproduced or distributed in any form without express written pemission from KIP 2013 KIP All references subject to change without notice 19 KIPFold 2000 User Guide Overview No part of this publication may be copied reproduced or distributed in any form without express wntten pemission from KIP 2013 KIP All references subject to change without notice 290 KIPFold 2000 User Guide Error Code List Code Location 1 Master Controller errors Description Communication and common errors EEPROM transfer error Communication error between FF and CF 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 1 10 1 11 1 12 License error Map fold panel width is smaller than 160mm or 6 3 inches Bad communication between FF and CF Wrong communication between FF and CF Data exchange failed from
8. Preset m L Preset 2 dropdown menu in the Fold column ease Preset file can be given a different fold packet s n This method can be used when a job has oe to be folded in a very specific way i GEM Meda Type cmd Ma FRM AIM diii that iisi recede m a Se ee Se a Tie Dol ee eT mna TSG Se Reet eter Br Ty Fee eta KHT near Matern KIP PrintNet and Folding When using the KIP PrintNet software there are two methods for printing using the KIPFold 2000 Method 1 In this method the fold packet to be used will be selected first by clicking the Job Defaults button on the main screen ribbon bar This will open the Job Defaults screen Once here select the desired Folder Packet setting to be applied to the entire job Doing this procedure prior to selecting the files to be printed will then apply the selected fold packet to all selected files making everything in the job ticket print 1 gar KIP b g and fold the same way i Be o N a y 7 Job Defaults D a l gt _ _ J Date of Request 4 9 2012 l __NewJob AddFiles Job Defaults LoadJob Save Job Mo l Pen Table default User admin Stamp Fold Selected Files Output Rotation Force Size Standard Size Enlarge Reduce Printing Options Email Confirmation No part of this publication may be copied reproduced or distributed in any form without express written
9. block leading Align in center The insertion rail on the table can be slid into an optimized position for the document you are feeding No part of this publication may be copied reproduced or distributed in any form without express written pemission from KIP 2013 KIP All references subject to change without notice 10 KIPFold 2000 User Guide Please try feeding the paper as straight as possible No part of this publication may be copied reproduced or distributed in any form without express written pemission from KIP 2013 KIP All references subject to change without notice 11 KIPFold 2000 User Guide Using the KIPFold 2000 with KIP Applications Once the KIPFold 2000 is installed and functioning KIP applications can be used to fold various packet sizes that were set up during configuration of the folder Available KIP Applications KIP Print KIP PrinNet KIP Windows Driver KIP AutoCAD Driver KIP C7800 Touchscreen Printing KIP Print and Folding When using the KIP Print software there are two methods for printing using the KIPFold 2000 Method 1 In this method the fold packet to be used will be selected first by clicking the Fold button on the main screen ribbon bar Once here select the desired Folder Packet setting to be applied to the entire job Doing this procedure prior to selecting the files to be printed will then apply the selected fold packet to all selected files ma
10. eferences subject to change without notic 4 KIPFold 2000 User Guide Main Folder Screen Offline Mode Shows the contact information of the technical service Program editor Click on meter counter to reset it This icon notes Manual mode The KIP printers control the online offline condition of the folder Opens a list of available folding programs No part of this publication may be copied reproduced or distributed in any form without express wntten pemission from KIP 2013 KIP All references subject to change without notice 5 KIPFold 2000 User Guide Media and formats Format limits Fan Folder All documents with length from 210 mm 8 5 up to 6 000 mm 19 6 ft 80 gr Paper or unlimited length option and width up to max 914 mm 36 Long copies will be deployed fan folded in the tray under the bridge Cross Folder Maximum paper length of 2500 mm Longer copies will not be transported into the cross folder but deployed fan folded in the catch tray under the bridge Recommended media The paper weight should not be less than 60 g m 18 and not more than 110 g m 24 For application of media types please contact your dealer Film or materials with glossy shiny surfaces are not suitable No part of this publication may be copied reproduced or distributed in any form without express wntten pemnnission from KIP 2013 KIP All references subject t
11. king everything in the job ticket print Sort Option Manage Transfer Printers and fold the same way KIP Print C7800 D oy O AEA AR Pe amp E New Job AddFiles Recall Job Enlarge Stamp Color 2 Up Pen Table Mirror Invert Viewlmage Free Reduce Options Selected Files Page Number Original Image Size Enlarge Reduce Output Image Size m m D x gt a ae C images Mixed Files 36x24 CAD GIS 1827 03 ML 0 C Almages Mixed Files 36x24 CAD GIS MapWindo id C images Mixed Files 24x18 Graphic Propane Av C images Mixed Files 24x36 Graphic Sam Adams Pane o E Use folder settings already configured on printer amp iwln vu UD Uv No part of this publication may be copied reproduced or distributed in any form without express written pemnnission from KIP 2013 KIP All references subject to change without notice 12 KIPFold 2000 User Guide Method 2 Je i In this method files will be added to the job m we ss css usse mme mans eno KIP Print C7800 cae SATIN ticket in the usual manner Add Files es nm AReoOnan l Al amk ce NewS anA Aitai E Sang Cot Ae Fo Por Tate birri ke Walaja Fobie Hist Prt Browse for and select files add them to saya ras oun seetndties fae ie Cg rage Se Fae Bp oF Bernese certae l the job to be printed Once the files to be Ba and eein R BE a E S A i ASE Comoter fema E E a printed have been added using the TE
12. move the plug from the power socket or turn off the fixed connection to the electricity grid and contact Customer Service Do not use the folder in rooms which are subject to excessive vibration Move the folder careful and slow using two persons Set the adjustable feet on the ground when the folder is in the desired position No part of this publication may be copied reproduced or distributed in any form without express wntten pemnnission from KIP 2013 KIP All references subject to change without notice aie KIPFold 2000 User Guide Main connection cable Do not use different connector cables other than supplied with the folder When replacement of the power supply cable is required because of damage or defect contact your CE for proper replacement of this power supply cable Mains connection Do not use an extension cable to connect the machine This machine is not designed for connection to an IT power supply system An IT power system is voltage network in which the neutral wire is not connected to earth When the machine is connected through a wall socket place the machine near a wall socket that is easily accessible When the machine is connected through a fixed connection to the electricity grid the disconnect device in the fixed connection must be easily accessible The machine must be connected to an earth grounded outlet Measures to take in case of an accident 1 If an accident has occurred
13. o change without notice se Select a folding program for offline function by pressing on the name of the fold currently selected Select the disired program 00 unfolded api DIN 198 TAB No part of this publication may be copied reproduced or distributed in any form without express written pemission from KIP 2013 KIP All references subject to change without notic a KIPFold 2000 User Guide Feeding prints In most cases the title block legend has to be on the leading edge of the document entering the folder The title block position has to be set in the printing software you are using rotation File Roll Printer output ane ieee No part of this publication may be copied reproduced or distributed in any form without express wntten pemnnission from KIP 2013 KIP All references subject to change without notice 8 KIPFold 2000 User Guide With the optional Rotation Unit A2 or C size formats can be printed landscape on an Ai or D size roll The folder will automatically rotate them into the right position File BN mee eee No part of this publication may be copied reproduced or distributed in any form without express wntten pennission from KIP 2013 KIP All references subject to change without notice O KIPFold 2000 User Guide Manual folding Deactivate the online connection from the printer s display Insert the sheet face down title
14. pemission from KIP 2013 KIP All references subject to change without notice 2 13 KIPFold 2000 User Guide Method 2 In this method files will be added to the job ticket in the usual manner Add Files Browse for and select files add them to the job to be printed Once the files to be printed have been added using the dropdown menu in the Fold column each file can be given a different fold packet This method can be used when a job has to be folded in a very specific way KIP Windows Driver and Folding When using the KIP Windows Driver to print and fold files follow these steps 1 Select the file to be printed in the appropriate E Ge ver asec application For this example Adobe is being used oa Current page P fi 6 2 Goto File and select Print ee Page Sizing amp Handling 3 When the Print window opens select the sce Prone E Mutipie E Booe installed KIP Windows Driver and then select aks iEn Actual size ee the Properties button ecm eae Ss Choose paper source page size Ch PDF i 4 When the Properties button opens select the pees Portrait Print Options Tab Landscape Want to print colors as gray amp black No part of this publication may be copied reproduced or distributed in any form without express wntten pemnnission from KIP 2013 KIP All references subject to change without notice 14 5 Under Folding check
15. this 11 Select OK again to return to the print screen and submit the file No part of this publication may be copied reproduced or distributed in any form without express wntten pemnnission from KIP 2013 KIP All references subject to change without notice 17 KIPFold 2000 User Guide KIP Touchscreen KIP C7800 and Folding When connected to a KIP C7800 Color printer and wanting to print and fold files follow these steps 1 Select the Print Button and browse to the location of the file s to be printed 2 Select the Next Arrow 3 When the next window opens choose the desired settings for the correct output a Under Rotation choose from 0 90 180 and 270 and Automatic b Under Folder choose from i Controller uses the Standard Percerttages Unattend ini file to determine ESI how to fold the files based on the files dimensions ii Preset 0 through 8 naming of presets to be determined during setup c If multiple files were selected a different setting can be given to each file No part of this publication may be copied reproduced or distributed in any form without express wntten pemnnission from KIP 2013 KIP All references subject to change without notice 18 KIPFold 2000 User Guide When connected to a KIP C7800 Color printer and wanting to fold files using the Offline function follow these steps 1 When the user first goes up to the K
16. utoCAD Plotte 3 20 2012 9 41 AM AutoCAD Plotte n Computer KIP Color Systems pc3 4 6 2012 2 43PM AutoCAD Plotte amp 0S C PublishToWeb JPG pc3 12 7 1999 10 53 AM AutoCAD Plotte G2 BLUTO DSVRO01S03 L PublishToWeb PNG pc3 11 21 2000 1 18 PM AutoCAD Plotte a DUR AA DSVRANI SNR D lt A KIP Color Systems pc3 Date modified 4 6 2012 2 43 PM Date created 4 6 2012 2 43 PM AutoCAD Plotter Configuration File Size 1 46 KB driver Recent Places 3 This will open the Plotter Configuration Editor 4 Select the Device and Document Settings Tab Eh pea PURRE Dee eae Eda tol Source and Size lt Sre Roll gt lt Width _ gt lt Size ANSI C 17 22 Ir 5 Select the Custom Properties option EE Graphics 6 Select the Custom Properties button Access Custom Dialog Press the following button to access the device diiver speciic user interface Custom Properties No part of this publication may be copied reproduced or distributed in any form without express wntten pemnnission from KIP 2013 KIP All references subject to change without notice 16 KIPFold 2000 User Guide 7 Once the custom properties window opens under Media Options select the Folder Button 8 Selecting On will use the Folder Presets V Prompt at plot time determined by the Presets ini file in the IPS 9 Select any of the available presets to apply that setting to the files being printed 10 Select OK to set
Download Pdf Manuals
Related Search