Operating instructions MT
Contents
1. MT 4x7 aa bb cc dd ee AC gg Power supply 100 240 VAC 50 60 Hz MT 4x7 aa bb cc dd ee DC gg Power supply 24 VDC MT 4x7 aa bb cc dd ee ff AL Aluminium front plate MT 4x7 aa bb cc dd ee ff VA Front plate stainless steel MT 4x7 aa bb cc dd ee ff RM Rear end module Page 12 of 28 R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 MT xx7 Serie Type code 9 2 Remote HMI Thin Client MT 5x7 MT 5x7 aa bb cc dd ee Front design Power supply Touch screen Display type Ethernet interface 557 567 577 587 Product type Product key structure Description Type with MT 5x7 FX MM bb cc dd ee Optical fiber Ethernet interface 100BaseFx Ex op is multi mode MT 5x7 TX bb cc dd ee Copper Ethernet interface 10 100BaseTx Ex nA MT 5x7 aa TFT cc dd ee TFT display standard MT 5x7 aa bb T dd ee Touch screen foil MT 5x7 aa bb TG dd ee Touch screen glass MT 5x7 aa bb cc AC ee Power supply 100 240 VAC 50 60 Hz MT 5x7 aa bb cc DC ee Power supply 24 VDC MT 5x7 aa bb cc dd AL Aluminium front plate MT 5x7 aa bb cc dd VA Front plate stainless steel MT 5x7 aa bb cc dd RM Rear end module R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 Page 13 of 28 MT xx7 Serie Type code 9 3 Remote HMI KVM MT 6x7 MT 6x7 aa bb cc dd ee Front design Power supply2. Optical fibre Fx 100BaseFx 100 Mbit intrinsically safe Ex op is only for MT 6x7 direct connection Cable type Optical fibre MM Optical fibre SM Multi mode optical fibre cable 50 um core cross section and 125 um external cross section Single mode optical fibre cable 9 um core cross section and 125 um external cross section USB 2x Ex ia 1x Ex nA USB For keyboard and mouse Ex ia Serial RS 232 Ex nA Video FBAS Ex nA Audio Line In Out interface Ex nA Data cable lengths Optical fibre MM up to 500 m 1 640 ft via 50 125 um optical fibre cable up to 300 m 985 ft via 62 5 125 um optical fibre cable up to 100 m 330 ft via CAT7 installation cable AWG 22 up to 140 m 460 ft via CAT7 installation cable AWG 22 up to 500 m 1 640 ft via CAT7 installation cable AWG 22 Enclosure Stahl Enclosure protection type IP66 R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 Page 7 of 28 MT xx7 Serie Conformity to standards Permitted ambient temperature 30 C 60 C range Cold start temperature Operating temperature range for DVI1 Cold start temperature Operation 5 C 40 C Permanent operation 5 C 40 C Operation with heater 5 C 40 C 10 C 50 C 20 C 60 C 20 C 50 C 30 C 50 C 60 C for a maximum of 5 h 30 C 70 C 30 C 5C
3. Operating instructions MT xx7 Series Panel PC MT 4x7 Remote HMI Thin Client MT 5x7 Remote HMI KVM MT 6x7 R STAHL HMI Systems GmbH Im Gewerbegebiet Pesch 14 D 50767 K ln HW Rev MT xx7 01 00 00 Doc No 60000189 Operating Instructions Version 01 01 00 Issue date 10 09 2012 MT xx7 Serie Publisher Publisher Publisher and copyright holder R STAHL HMI Systems GmbH Im Gewerbegebiet Pesch 14 D 50767 K ln Registered place of business Cologne Registration Court AG Cologne HRB 30512 USt Id Nr VAT number DE 812 454 820 Telephone switchboard 49 0 221 5 98 08 200 Hotline 59 Telefax 260 E mail office stahl hmi de Hotline support stahl hmi de e All rights reserved e This document may not be reproduced in whole or in part except with the written consent of the publisher e Wereserve the right to make technical changes without notice This documentation has been produced and checked with due care R STAHL HMI Systems GmbH shall however not accept liability for any mistakes in this and all other documents Any warranty claims are limited to the right to demand amendments Liability for any damage that might result from the contents of these instructions or all other documentation is limited to clear cases of premeditation We reserve the right to change our products and their specifications at any time provided it is in the interest of technical progress The information in the curren
4. Touch screen Display type Transfer technology 657 667 677 687 Product type Product key structure Description Type with MT 6x7 DVI1 CAT bb cc dd ee DVI1 KVM with direct copper connection Gigabit Ex nA MT 6x7 DVI1 MM bb cc dd ee DVI1 KVM with direct optical fibre connection Ex op is multi mode MT 6x7 DVI1 SM bb cc dd ee DVI1 KVM with direct optical fibre connection Ex op is single mode MT 6x7 DVI2 CAT bb cc dd ee DVI2 DVI with direct copper connection Gigabit Ex nA MT 6x7 aa TFT cc dd ee TFT display standard MT 6x7 aa bb T dd ee Touch screen foil MT 6x7 aa bb TG dd ee Touch screen glass MT 6x7 aa bb cc AC ee Power supply 100 240 VAC 50 60 Hz MT 6x7 aa bb cc DC ee Power supply 24 VDC MT 6x7 aa bb cc dd AL Aluminium front plate MT 6x7 aa bb cc dd VA Front plate stainless steel MT 6x7 aa bb cc dd RM Rear end module Page 14 of 28 R STAHL HMI Systems GmbH OI MT xx7 en V 1 01 00 docx 10 09 2012 MT xx7 Serie Safety information 10 10 1 10 2 Safety information General Safety Information All relevant accident prevention regulations and the rules for electric installations have to be observed during installation maintenace and operations All persons involved in installation commission maintenance and repairs of this device and its accessories must be qualified accordingly and must have fa
5. 10 09 2012 Power supply of the operator interface Ex nA USB interface Ex ia for External keyboard USB interface Ex ia for Mouse USB Ex nA Ethernet copper connection Ex nA Ethernet optical fibre interface Ex op is USB interface Ex ia USB interface Ex ia Serial Ex nA interface RS 232 Page 19 of 28 MT xx7 Serie Operation CAM 2 GND Black Ex nA interface X105 CH1 line out left Audio CH line out right Ex nA interface 1 2 3 CH3 line in left 4 5 AUD CHA line in right GND a The following applies to all terminals 0 2 2 5 mm 24 AWG 16 AWG for flexible cable 0 2 4 mm 24 AWG 14 AWG for rigid cable Strip cable of 7 mm 0 28 in insulation max one cable per terminal recommended cable length for terminals X11 X12 X13 X14 X24 X25 max 3 m 10 ft Please note that the Ethernet connection is either for an optical fibre connection X16 or for a copper connection X18 depending on the version ordered If display types MT xx7 DVI1 MM or MT xx7 DVI1 SM optical fibre versions are used terminal X16 remains unused In the case of an optical fibre connection the following cable is recommended Multi mode optical fibre cable 50 um core cross section and 125 um external cross section Single mode optical fibre cable 9 um core cross section and 125 um external cross section The USBi2 connection X25 is NOT available for devices with
6. P 629 mW C negligible uF C 50 uF Li negligible mH Lo 40 uH USB1i X24 The maximum values are U 5 5 C ET NE C li E 3 A lo 309 mA P 2 W Po 629 mW Ci negligible uF C 50 uF Li negligible mH Lo 40 uH USB2i X25 The maximum values are U 55 C Us 55 C li 3 A lo 309 mA Pi 2 W Po 629 mW Ci negligible uF Co 50 uF Li negligible mH Lo 40 uH R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 Page 11 of 28 MT xx7 Serie Type code 9 Type code 9 1 Panel PC MT 4x7 MT 4x7 aa bb cc dd ee ff g Front design Power supply Data memory Main memory Touch screen Display type Ethernet interface 457 467 477 487 Product type Product key structure Description Type with MT 4x7 FX MM bb cc dd ee ff gg Optical fiber Ethernet interface 100BaseFx Ex op is multi mode MT 4x7 TX bb cc dd ee ff gg Copper Ethernet interface 10 100BaseTx Ex nA MT 4x7 aa TFT cc dd ee ff gg TFT display standard MT 4x7 aa bb T dd ee ff gg Touch screen foil MT 4x7 aa bb TG dd ee ff gg Touch screen glass MT 4x7 aa bb cc R1 ee ff gg Working memory 1 GB MT 4x7 aa bb cc R2 ee ff gg Working memory 2 GB MT 4x7 aa bb cc dd 4GB ff gg 4 GB Solid State Drive MT 4x7 aa bb cc dd 16GB ff gg 16 GB Solid State Drive MT 4x7 aa bb cc dd 100GB ff gg 100 GB hard disk internal
7. R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 R STAHL HMI Systems GmbH Im Gewerbegebiet Pesch 14 D 50767 K ln Phone switchboard 49 0 221 59808 200 hotline 59 Fax 260 E mail switchboard office stahl hmi de hotline support stahl hmi de www stahl de www stahl hmi de
8. Special conditions 17 11 Assembly and disassembly 18 11 1 General information 18 11 2 Cut out MT xx7 18 12 Operation 18 12 1 General information 18 12 2 Connections 19 13 Maintenance 21 14 Troubleshooting 21 14 1 Repairs hazardous substances 21 15 Disposal 21 15 1 1 ROHS directive 2002 95 EC 21 16 Trademarks 21 17 Front panel resistance 22 17 1 Materials 22 17 1 1 Material properties 22 R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 Page 3 of 28 MT xx7 Serie Table of contents 17 1 2 Touch membrane polyester 22 18 Declaration of EC conformity 25 19 Release notes 26 Page 4 of 28 R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 MT xx7 Serie Preface 1 Preface These Operating Instructions contain all aspects relevant to explosion protection for the MT xx7 operator interfaces Panel PC and Remote HMI series They also contain information on the connection and installation of these devices Please also refer to additional documentation included in the delivery such as the EC type examination certificate and the hardware manual which contain further important information N For the correct operation of all associated components please note in addition to these operating instructions all other operating instructions enclosed in this delivery as well as the operating instructions of the additional equipment to be connected N Please also note
9. out with the following dimensions Width Height Depth of cut out Material thickness 615 0 5mm 435 0 5 mm 110 mm up to 5 mm 24 21 0 002 17 13 0 002 4 33 up to 0 02 12 Operation 12 1 General information When operating the devices particular care shall be taken that the operator interface has been properly installed according to instructions the device is undamaged the terminal compartment is clean all screws are tightened fast before switching the operator interface on its external PE terminal is properly connected to the equipotential bonding system at its place of use e the cover of the terminal compartment is completely closed Page 18 of 28 R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 MT xx7 Serie Operation 12 2 Connections Terminal Pin Definition typcial cable colour Power supply operator interface 24 VDC or 100 240 VAC Power supply operator interface 0 VDC or 100 240 VAC Earth operator interface White Orange CAT7 1 Orange Data White Green Green Blue White blue White Brown Brown Screen optical fibre connection type LC Duplex connector An X24 USB1i X25 USB2i Blue White blue White Orange Orange X97 SER 5 Black R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx
10. size M16x1 5 and M20x1 5 The wall of the terminal box where the cable entries are mounted has a thickness of at least 4 mm The cable connections must be tightened fast according to regulations Unused cable connections must be sealed with appropriate blind plugs Only permanently laid cables may be connected to the pre mounted ATEX cable connections The outer cable diameters must correspond to the cable connection specifications Cable entry M16 for round cable outer cable diameter 5 9 mm 0 2 0 35 Cable entry M20 for round cable outside cable cross section 9 13 mm 0 35 0 51 R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 Page 15 of 28 MT xx7 Serie Safety information e The device must not be opened maintained or repaired in hazardous atmospheres sole exception the connection box All circuits must be completely de energised before the device is connected Before opening the connection box ensure that all circuits are isolated You must also ensure that the power supply circuit is isolated The cable diameter must meet the terminal specifications The connection box must be tightly sealed e The wire used for earthing must have a minimum cross section of 4mm Make sure that there is equipotential bonding between the devices e We recommend you use screened cables with the device Routing of the data cable may reduce performance The cables used in intrinsically safe circuits must have been
11. tested to AC 500 V DC 750 V If the cable properties are unknown assume 200 pF m and 1uH m e f display types MT xx7 DVI1 MM or MT xx7 DVI1 SM are used terminal X16 remains unused e To establish a secure earthed connection between device and plant and to prevent inadvertent loosening of the cables each cable with its screen must be connected to the corresponding earthing bracket located in the Ex nA connection box close to the associated terminal e At the place of installation voltage must not exceed 250 V and short circuit current must not exceed 1500 A e A tick close to the X10 terminal indicates the voltage type AC DC For the 24 VDC types the cable cross sections depend on the cable length of the voltage supply cable as follows Cable un in metres Cable cross section in mm AWG t max 55 m 180 ft 1 5 mm AWG 16 max 90 m 295 ft 2 5 mm AWG 14 max 150 m 492 ft 4 mm AWG 12 max 225 m 738 ft 6 mm AWG 10 max 375 m 1230 ft 10 mm AWG 8 max 600 m 1968 ft 16 mm AWG 6 If the cable s cross section is greater than the maximum possible for the terminals the cable needs to be routed according to regulations via a smaller cable cross section before being inserted into the connection box possibly using the Ex e terminal box e If the intrinsically safe interfaces of an intrinsically safe device or a partially intrinsically safe device are or have been connected to a
12. that all certificates for the operator interfaces are included in a separate document 1 1 General Notes Please read the entire operating instructions before assembling the product In case of doubt the German original shall apply We assume no liability for any typographical errors in these operating instructions In case of questions or suggestions please don t hesitate to contact R STAHL HMI Systems GmbH 1 2 Technical progress Alterations reguire the written consent of R STAHL HMI Systems GmbH The manufacturer reserves the right to adjust technical data to be in line with technical progress without any specific announcements R STAHL HMI Systems GmbH OI MT xx7 en V 1 01 00 docx 10 09 2012 Page 5 of 28 MT xx7 Serie Device function 2 Device function The MT xx7 operator interfaces are explosion protected equipment for installation in hazardous areas and can be operated in zones 2 and 22 with interfaces for zones 0 1 2 and 20 21 22 The devices are connected to a communication system via the serial interfaces RS 232 Ethernet located in their connection box at the rear The connection box also contains the USB interfaces for the connection of various peripheral devices Furthermore the interfaces for keyboard mouse video and audio signals are also located here 2 1 Panel PC MT 4x7 The MT 4x7 operator interfaces are intelligent display and operating devices which can run any software and are thus easy to ope
13. 40 C Storage temperature range 20 C 70 C The heater used must be of such a design that the temperature inside the operator interface s Comment Heat dissipation housing does not fall below 20 C 30 C only at the front about 40 via the front plate and 60 via the enclosure 10 to 90 at 40 C non condensing Relative humidity for DVI1 20 to 80 at 40 C non condensing Dimensions mm inch Front w x h 660 x 475 25 98 x 18 70 Cut out w x h 0 5 0 002 615 x 435 24 21 x 17 13 Depth of cut out 110 4 33 Wall thickness lt 5 0 02 Mounting position vertical or horizontal Weight kg Ib Operator interface 4 Conformity to standards The MT xx7 operator interfaces comply with the 16 00 35 3 Ib following standards and directives Standard directive 94 9 EC Classification Initial certification EN 60079 0 2009 General requirements EN 60079 11 2007 Intrinsic safety i EN 60079 15 2010 Type of protection n EN 60079 28 2007 Optical radiation EN 60079 31 2009 Protected by enclosures tD dust EN 61241 11 2006 Electromagnetic compatibility directive 2 004 108 EC EN 61000 6 2 2006 Interference resistance EN 61000 6 4 2007 Interference emission Low voltage directive directive 2006 95 EC EN 50178 1997 Fitting p
14. T 667 MT 477 MT 577 MT 677 TFT Color display 16 7 million colours MT 487 MT 587 MT 687 Display size 48 cm 19 56 cm 22 61 cm 24 61 cm 24 WU Resolution in pixels SXGA 1280 x 1024 WSXGA Full HD 1920 x 1080 WUXGA 1920 x 1200 Format 5 4 1680 x 1050 16 9 16 10 16 10 Display Glass Touch Screen optional Membrane or glass surface 5 wire analogue resistive Backlight LED background lighting Service life MTBF of backlight at 20 C typically 50 000 h Brightness 350 cd m 300 cd m 250 cd m Contrast 1000 1 Additional keyboard optional Power supply 107 keys with integrated trackball joystick mouse pad or touch pad Directly in the integrated connection box Connections via control spring terminals green flexible cable up to 2 5 mm AWG 16 fixed cable up to 4 mm AWG 14 Voltage supply 24 VDC or 100 240 VAC 50 60 Hz Power consumption A at 24 VDC max 3 A at 100 240 VAC max 1 A Power typically 35 W max 150 W typically 119 BTU max 510 BTU Recommended fuses 5AT only for MT 4x7 and MT 5x7 Real time clock Data buffer Battery Capacitor Interfaces Yes Lithium battery and capacitor buffered maintenance free gt 5 years at least 4 days Ethernet Either Tx or Fx Copper Tx 10 100BaseTx 10 100 Mbit Ex nA only for MT 6x7 direct connection Gigabit
15. as disposal or damage to persons chemical burns etc 15 Disposal Disposal of packaging and used parts is subject to regulations valid in whichever country the device has been installed The disposal of devices sold after August 13th 2005 and installed in countries under the jurisdiction of the EU is governed by directive 2002 96 EC on waste electrical and electronic equipment WEEE Under this directive operator interfaces are listed in category 9 monitoring and control instruments We shall take back our devices according to our General Terms and Conditions 15 1 1 ROHS directive 2002 95 EC The prohibition of hazardous substances as detailed in directive 2002 95 EC ROHS does not apply to electronic equipment of categories 8 and 9 and is therefore not applicable to the equipment described in these operating instructions 16 Trademarks Any trademarks used and depicted in the text are the property of their respective owners and are recognised as protected R STAHL HMI Systems GmbH OI MT xx7 en V 1 01 00 docx 10 09 2012 Page 21 of 28 MT xx7 Serie Front panel resistance 17 Front panel resistance This section contains information on the resistance of the operator interfaces to various environmental factors These have an impact on the mechanical thermal and chemical stability of the operator interfaces The resistance to chemicals was tested according to DIN 42115 Part 2 i e the stability over 24 hours w
16. ecommissioned the damaged components must be replaced If you want to use the device in category 1D 2D 3D or EPL Da Db Dc dust deposita of a thickness exceeding 5 mm must be removed and you have to ensure that no high energy loading mechanisms at the operating surface of the unit e g pneumatic particle transport occur during operation The device may not be used in environments where propagating brush discharges may occur In general and particularly when opening and closing enclosures users must take care not to get injured by getting caught trapped In case of non compliance or contravention of the above explosion protection is no longer guaranteed and all warranty claims shall be null and void 10 4 Special conditions Equipotential bonding must be established for the external intrinsically safe circuits of the accessories to be connected e g display keyboard or pointer device R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 Page 17 of 28 MT xx7 Serie Assembly and disassembly 11 Assembly and disassembly 11 1 General information Assembly and disassembly are subject to general technical rules Additional specific safety regulations apply to electronic and pneumatic installations In Germany for example these include the BG regulations Government Safety Association and the BetrSichVer Betriebsicherheitsverodnung Occupational Health and Safety 11 2 Cut out MT xx7 Make a cut
17. ithout visible changes to the operator interfaces 17 1 Materials Application Material Front plate Aluminum Touch screen Polyester Enclosure Stainless steel Front panel seal Polyurethane 17 1 1 Material properties The selection of chemicals listed here is not exhaustive More comprehensive lists can be obtained for further information from R STAHL HMI Systems GmbH Because of the numerous chemical substances available on the market these lists can only represent a selection 17 1 2 Touch membrane polyester Property heme materal Chemical substances Test method class group Chemical Alcohols 1 3 Butanediol e Chemical 1 4 Butanediol resistance Cyclohexanol Diacetone alcohol Ethanol Glycol DIN 42115 Glycerol DIN 53 461 Isopropyl alcohol or Methanol ASTM F 1598 95 Neopentyl glycol Octanol 1 2 Propylene glycol Triacetin Dowandol DRM PM Aldehydes Acetaldehyde Formaldehyde 37 42 Amines Ammonia lt 2 Esters Amyl acetate Ethylacetate N Butyl acetate Page 22 of 28 R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 MT xx7 Serie Front panel resistance Ethers 1 1 1 Trichloroethane Ether Dioxane Diethyl ether 2 Methyltetrahydrofuran 2 ME THF Aromatic hydrocarbons Benzene Toluene Xylene Paint thinner white spirit Ketones Acetone Methyl ethyl ketone Cyclohexanone Methy
18. l isobutyl ketone MIBK Isophorone Diluted acids Formic acid 5096 Acetic acid 596 Phosphoric acid 3096 Hydrochloric acid lt 10 Nitric acid lt 10 Trichloroacetic acid lt 50 Sulfuric acid lt 30 Diluted alkaloids bases Caustic soda lt 40 Household chemicals Ajax Ariel Domestos Downey Fantastic Formula 409 Gumption Jet Dry Lenor Persil Tensides Top Jop Vim Vortex Washing powder Fabric conditioner Whis Windex Oils Petrol Drilling muds Braking fluid Decon foam Diesel oil Varnish Keroflux Paraffin oil Castor oil Silicone oil Solvent naphta Mineral turpentine Kerosene R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 Page 23 of 28 MT xx7 Serie Front panel resistance No specific material Acetonitrile class Alkali carbonate Dichromates Potassium dichromate Caustic soda lt 20 Dibutyl phthalate Dioctyl phthalate Iron II chloride FeCls Iron II chloride FeCls Haloalkanes Potassium soap Potassium hydroxide lt 30 Sodium bisulfate Tetrachloroethylene Salt water Trichloroethylene Water Hydrogen peroxide gt 25 Property Resistance Test method Mechanic keyboard e durability gt 1 million actions Autotype method e Action power max 50 N ASTM D2176 e MIT folding resistance gt 20000 folding operations Mechanic touch e Dimension stability screen 3M method e poi
19. miliarised themselves with this manual and any associated documentation In case of non compliance or contravention of the above explosion protection is no longer guaranteed and all warranty claims shall be null and void National safety and accident prevention rules apply Use the device for its intended purpose only No changes to the device are permitted The enclosure may only be opened by R STAHL HMI Systems GmbH The first four digits of the serial number on the type plate stand for the year of manufacture Installation safety information The national assembly and installation rules and the generally accepted technical rules must be observed The device and its accessories must be connected and operated according to applicable standards directives and installation guidelines Only qualified personnel or personnel that has been instructed accordingly are allowed to install the device Only appropriate tools must be used for the installation The screws on the lid of the Ex nA connection box must be fastened with a torque of 1 N The cable connections of the connection box must be in line with country specific regulations and may have to be adapted accordingly Potential changes to the ambient parameters such as temperature must be taken into account The cable entries in the connection box must have ingress protection IP 66 or may have to be adapted to meet country specific requirements The pre assembled cable entry threads are
20. not intrinsically safe circuit the certification ceases to apply and the device may no longer be operated as an intrinsically safe device After the device has been operated as intrinsically safe with a low level of protection e g an Ex ia device at an Ex ib interface it may no longer be operated in applications for a higher level of protection e g ia Page 16 of 28 R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 MT xx7 Serie Safety information If the device is being used in a dust atmosphere and must be replaced the device or the enclosure in which it is mounted must be disconnected from the mains first and then according to regulations be left to cool down Before opening the device or its enclosure and whilst they are open the environment must be kept dust free so that no dust can intrude into the inside of the enclosure When mounting new components please ensure that all seals are undamaged and fit tightly Before starting up the device you must ensure that it has been installed according to regulations and that neither the device nor its cables are damaged 10 3 Safety information for operation Operate the device only if it is clean and undamaged If the device is in any way damaged do not touch it to avoid injury In the case of any damage that may compromise ingress protection e g cracks holes or broken components the device must be taken out of commission immediately Before the device is r
21. nsumption Imax Max operating voltage Um RS 232 SER X97 Rated voltage Max operating voltage Um Video CAM X101 Rated voltage Max operating voltage Um Audio AUD X105 Rated voltage Max operating voltage Um 20 240 V AC DC depending on type lt 5A lt 150 W lt 250 VAC lt 1500 A 5 VDC 10 lt 250 VAC 12 VDC 10 lt 400 mA lt 250 VAC 15 VDC 10 lt 250 VAC 5 VDC 10 lt 250 VAC 100 VDC 10 lt 250 VAC Copper Ethernet CAT7 1 X16 Rated voltage Max operating voltage Um Page 10 of 28 5 VDC 10 lt 250 VAC R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 MT xx7 Serie Permitted maximum values 8 2 External inherently safe optical interface Ethernet optical fiber FO 1 X18 Multi mode Wavelength 850 nm Radiant power 0 22 mW max radiant power 35 mW Single mode Wavelength 1310 nm Radiant power 0 22 mW max radiant power 35 mW 8 3 External intrinsically safe circuits Keyboard X11 The maximum values are Ui E 55 C Ui J 95 C li 3 A lo 309 mA P 2 W P 629 mW C negligible uF C 50 uF Li negligible mH Ls 40 uH Pointer device X12 The maximum values are U 5 5 C Ui 55 C li 3 A lo 309 mA Pi x 2 W
22. nt activation 1 million activations at any single point Thermal e Dimensional Max 0 2 at 120 longitudinal Autotype method Typically 0 1 Page 24 of 28 R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 MT xx7 Serie Declaration of EC conformity 18 Declaration of EC conformity EG Konformitatserklarung EC Declaration of Conformity D claration de Conformit CE R STAHL HMI Systems GmbH Im Gewerbegebiet Pesch 14 50767 K ln Germany erkl rt in alleiniger Verantwortung declares in its sole responsibility d clare sous sa seule responsabilit dass das Produkt MTT that the product que le produit Typ type typa Display Unit MT 7 CAT7 Display Unit MT 7 MM Display Unit MT 7 SM zany alphanumeric or symbalic character without relevance for explosion protection sne rumarie character wat relevance for aaploskan protection Kennzeichnung marking marquage For Display Unit amp II 3 1 G Ex nA nR ia op is Ga IIC T4 Gc 11 3 1 D Ex tc IIIC ia op is Da IP66 T110 C Dc mit der EG Baumusterpr fbescheinigung BVS 12 ATEX E 033 X ausgestellt durch Benannte Stelle under EC Typa Examination Certificate DEKRA EXAM GmbH issued by notified body Dinnendahlstra e 9 avec Attestation d examen CE de type 44808 Bochum expos par organisme notifi auf das sich diese Erkl rung bezieht mit den folgenden Norman oder normativen Dokumenten bereinstimmt which i
23. ower plants with electronic equipment EN 61010 1 2001 General requirements Page 8 of 28 R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 MT xx7 Serie Certificates 5 Certificates The MT xx7 operator interfaces are certified for installation in the following areas according to ATEX Directive 94 9 EC for installation in zones 2 and 22 5 1 ATEX The ATEX certificates are listed under the following certification numbers Certificate number for MT xx7 BVS 12 ATEX E 033 X 6 Marking Manufacturer R STAHL HMI Systems GmbH Type code MT xx7 CE classification CE 0158 Testing authority and certificate BVS 12 ATEX E 033 X number Ex classification ATEX guideline 94 9 EC II 3 1 G Ex nA nR ia op is Ga IIC T4 Gc E II 3 1 D Ex tc IIIC ia op is Da IP66 T110 C Dc 7 Power supply 7 1 Operator interfaces Power supply 24 VDC or 100 240 VAC 50 60 Hz Power consumption at 24 VDC max 3A at 100 240 VAC max 1 A R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 Page 9 of 28 MT xx7 Serie Permitted maximum values Permitted maximum values External non intrinsically safe circuits Input voltage PWR X10 Nominal voltage Power consumption Imax Power Pmax Max operating voltage Um Short circuit current Ix USB X13 Rated voltage Max operating voltage Um 12 V X14 Rated voltage Power co
24. rate The devices are fitted with powerful processors and are thus able to process even large applications on site The devices have a back up and recovery system which can be used to save complete images and load them onto new Panel PCs without requiring specific IT skills The X13 interface is provided for this purpose 2 2 Remote HMI Thin Client MT 5x7 The Remote HMls of the MT 5x7 series can be integrated into modern networks as Thin Clients or with a KVM box via KVM over IP Digital Ethernet technology is used for the data transfer between KVM box and Remote System Up to four Remote HMlIs can access one KVM box with one software license thus cost effectively communicating with several PCs for example when monitoring the production process and simultaneously applying Condition Monitoring Multi monitoring with several on site terminals can as easily be implemented as the application as Thin Client in a server environment with virtual work stations 2 3 Remote HMI KVM MT 6x7 The KVM Classic transfer technology is used for the point to point connection between a PC and an MT 6x7 Remote HMI terminal There are two versions DVI1 and DVI2 of this transfer technology that have slightly different functionality Page 6 of 28 R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 MT xx7 Serie Technical Data 3 Technical Data Function Equipment Display type MT 457 MT 557 MT 657 MT 467 MT 567 M
25. s the subject of this declaration is in conformity with he following standards or normative documents auquel cefte d claration se rapporte est conforme aux normes ou aux documents normatifs suivants Bestimmungen der Richtlinie Nummer sowie Ausgabedatum der Norm Terms of the directive Number and date of issue of the standard Prasenpilon de la directive Num ro amsi que date d mission de la norme 94 9JJEG ATEX Richtlinie EN 60079 0 2009 94 Q EC ATEX Directive EN 60079 11 2007 94 S CE Directiva ATEX EN 60079 15 2010 EN 60079 28 2007 EN 60079 31 2008 EN 61241 11 2006 2004 08 EG EMV Richtlinie EN 61000 6 2 2006 2004 f08 EC EMC Directive EN 61000 6 4 2007 2004 108 CE Directive CEM 2006 95 EG Niederspannungsrichtlinie 2008 05 EC Low Voltage Directive EN 50178 1997 2006 95 CE Directive Basse Tension EN 61010 1 2001 Corrigendum Errata Ve 3 u i K ln 04 04 2012 joe DR Y 7 Es C Ort und Datum J D ren W Bertges Place and date Technical Direcfor Quality Manager Lieu et dafe Datei CE MT x7 20120404 goes Vorlage FO53 EG Kenler rung HMI 20110325 docx R STAHL HMI Systems GmbH OI MT xx7 en V 1 01 00 docx 10 09 2012 Page 25 of 28 MT xx7 Serie Release notes 19 Release notes The chapter entitled Release Notes contains all the changes made in every version of the operating instructions Version 1 01 00 e Original version of the operating instructions Page 26 of 28
26. t manual online or on CD or in the operating instructions included with the operator interface applies Trademarks The terms and names used in this document are registered trademarks and or products of the companies in question WINDOWS 95 98 2000 NT ME XP Vista 7 Server are registered trademarks of MICROSOFT Corporation USA Copyright 2012 by R STAHL HMI Systems GmbH Subject to alterations Page 2 of 28 R STAHL HMI Systems GmbH OI MT xx7 en V 1 01 00 docx 10 09 2012 MT xx7 Serie Table of contents Table of contents Publisher 2 Table of contents 3 1 Preface 5 1 1 General Notes 5 1 2 Technical progress 5 2 Device function 6 2 1 Panel PC MT 4x7 6 2 2 Remote HMI Thin Client MT 5x7 6 2 3 Remote HMI KVM MT 6x7 6 3 Technical Data 7 4 Conformity to standards 8 5 Certificates 9 5 1 ATEX 9 6 Marking 9 7 Power supply 9 7 1 Operator interfaces 9 8 Permitted maximum values 10 8 1 External non intrinsically safe circuits 10 8 2 External inherently safe optical interface 11 8 3 External intrinsically safe circuits 11 9 Type code 12 9 1 Panel PC MT 4x7 12 9 2 Remote HMI Thin Client MT 5x7 13 9 3 Remote HMI KVM MT 6x7 14 10 Safety information 15 10 1 General Safety Information 15 10 2 Installation safety information 15 10 3 Safety information for operation 17 10 4
27. touch screen and may NOT be connected Page 20 of 28 R STAHL HMI Systems GmbH Ol_MT_xx7_en_V_1_01_00 docx 10 09 2012 MT xx7 Serie Maintenance 13 Maintenance Because the transmission of the devices remains reliable and stable over long periods of time regular adjustments are not required Keep the units clean so that the enclosure locks and screws remain accessible Maintenance may be required for the enclosure seal System maintenance should focus on the following a Seal wear b Display damage c All screws are tightened fast d All cables and lines are properly connected and undamaged 14 Troubleshooting Devices operated in hazardous areas must not be modified Repairs may only be carried out by qualified authorized staff specially trained for this purpose Repairs may only be carried out by specially trained staff who are familiar with all basic conditions of the applicable user regulations and if requested have been authorized by the manufacturer 14 1 Repairs hazardous substances An error description must be enclosed with any units returned to R STAHL HMI Systems GmbH for repairs Remove all material residues Please pay particular attention to the seal grooves and slits where material residues may be lodged We have to ask you not to return a unit if you are unable to completely remove any hazardous substances We shall bill you for any costs arising from insufficiently cleaned units such
Download Pdf Manuals
Related Search