Home

Operating Instructions

Contents

1. Beane MENN bck a number to amar the Racording Schadula Property Page ieme shown in red gre curteni inertie No The schedule number is indicated To edit the recording schedule click this to display the Recording Schedule Properties menu From Start time day and time of the schedule will be displayed When Daily for Day Every for Hour and Every for Minute are selected Continuous will be displayed here To End time day and time of the schedule will be dis played When Daily for Day Every for Hour and Every for Minute are selected Continuous will be displayed here Camera No The number of the camera to be scheduled will be displayed Protection Mode If the disk space is protected it displays Protect if not Overwrite Interval The recording interval will be displayed When pictures are recorded in the JPEG format actual recording interval may be different from the displayed value Refer to page 63 for further infor mation When pictures are recorded in the MPEG 4 format recording interval differs depending on the trans mission speed of cameras Priority The priority level 1 4 will be displayed 1 is the highest priority When two or more camera record ing schedules overlap the recording schedule with higher priority will be applied If the priority level is also the same priority will be decided as follows e When a schedule is registered w
2. Setting Menu e Camera 1 Title Assigning a title of up to 16 characters to the cam era is possible IP Address Enter the IP address of the selected camera It is possible to enter the FQDN Fully Qualified Domain Name of the selected camera When a camera uses an HTTP port except port number 80 to deliver pictures enter colon port number just after the IP address or the FQDN For example 192 168 0 50 85 Channel When the registered camera is connected to a net work interface unit WJ NT104 select the channel 1CH 4CH of the network interface unit used for the selected camera from this pull down menu When the registered camera is connected directly without a network interface unit WV NP472 WV NS320 WV NS324 WV NM100 select 1CH Operating Restriction Select one of Unrestricted View And Preset Only or By Camera Group Setting to restrict users access to the camera or not Unrestricted When Unrestricted is selected all users Can access and operate the camera except for recording View And Preset Only Browsing live pictures and preset operations are available By Camera Group Setting Register a camera to groups using the Camera Group Setting page first User Camera Group button Camera Group Setting tab The Operator type users belonging to the group can operate this camera including for recording The Monitor type users belongi
3. LAN Cable PC Software Package WV AS710 Web Server Apache 2 0 40 LAN Cable OS Red Hat Linux 8 0Professional Coaxial Cable PC Server Disk Space for Recorded Picture Hard Disk Network Camera Server Camera 7 Network Interface Unit Center Site Camera Site When using cameras connected by coaxial cable Access the network using the network interface unit WJ NT104 The network camera server identifies the IP address and the camera channels of the network interface unit and acquires camera pictures and controls the cameras When using network cameras with built in 1OBASE T 100BASE TX Ethernet port connected by LAN cable Access the network assigning unique IP addresses to each camera The network camera server identifies the IP addresses assigned to each camera and acquires camera pictures and controls the cameras User Site Users can browse camera pictures by entering the address of the network camera server in the address box of a web browser in the same way they access web pages using a web browser Users don t need to remember the IP address of each camera thanks to menus displayed in the web browser that allow them to select and operate the desired camera When connected cameras are compatible with MPEG 4 users
4. ccccccoocnnnnnnncccconnnccnncncononccnncnnononcnnnnnnnnnnnnnnnnnnnnnannnnnnnnonans 61 Recording Schedule Properties oocccccccconnnccnnccononnccnncnnononccnnnnnnnonanonnnnnnonanecnnnnnnnans 62 Alarm o x aicanscteasenavaaieaaneaisnonstunotuest PP E r eiei aaeas 64 eo A e 67 A P P P E ate onteesdeeaneeses gee 68 A ae ne case teen tecaecdees EE cero 69 User TACOS TA MOM sustancia 70 Change User Protile iiceccscadecsxctsecensiabcncnajsatencectiedee seu otra ancianidad 71 Camera 1 ONION ascii ade 72 GOUD NAME reaa a E E E A 13 Sci o 74 ASNO MIC QUO ninas a E E EOS E E 17 E Mail Setting ccccseeccccceeseeecceeseeeeceeusececeauueeecseeaeceeesaseeesseaaeeesssauseessssgeeeessnseesesas 78 der Amo erasers eeeteeneeeaeere 79 ico A en 80 FEATURES The PC Software Package WV AS710 hereinafter referred to as WV AS710 is designed to deliver pictures from cameras at remote locations to personal computers PCs via an IP network such as the Internet Intranet Install the WV AS710 in a PC server whose OS is Red Hat Linux 8 0 Professional to run the network camera server a PC server in which the WV AS710 is installed is referred to as a network camera server in this operating manual Users can browse delivered pictures using web browsers on PCs Coaxial Cable LAN Cable Camera Network Interface Unit Modem Router Hub etc
5. Click this link text to return to the Camera List menu 91 Camera Sleep Schedule Camera Sleep Schedule List Click the Camera button of the Setting Menu to display the Camera List menu and click the Camera Sleep Schedule tab The Camera Sleep Schedule menu will be displayed It is useful to check the camera sleep schedules with this page The Camera Sleep Schedule is the function to stop delivery of camera pictures and to display a prepared still pic ture at the designated time Up to 20 schedules can be registered Click the Camera Sleep Schedule tab Active schedules will be displayed in black and inactive schedules will be displayed in red Setting Menu Cick a number to erter the Camera Sleep Sched de hems shown in red are currently inactive No The schedule number is indicated To edit the cam era sleep schedule click this to display the Camera Sleep Schedule menu From Start time day and time of the schedule will be displayed To End time day and time of the schedule will be dis played Camera No The number of the camera to be scheduled will be displayed Priority The priority level will be displayed 1 is the high est priority When two or more camera sleep schedules overlap the camera sleep schedule with higher priority will be applied If the priority level is also the same priority will be decided as follows e When a schedule is registered while the net
6. WY AST 0 iini working Please Stat WV ASTIO Jian WAST To MIFEC4 Plisebti aera al TPE Ge Player Mirando sil Start up from Red Hat Linux Execute s3 in the directory where the WV AS710 is installed When the WV AS710 is installed in the default path it has been installed in usr local s3 bin usr local s3 bin s3 Notes e Executing s3 is not necessary if Start WV AS710 automatically when starting Linux is selected when the WV AS710 is installed and the server is restarted e When the automatic startup of the WV AS710 or the manual restart of the WV AS710 by an administrator is per formed the WV AS710 will start running in the background Therefore nothing will be displayed in the terminal window The Settings of the Network Camera Server Just after Completing the Installation are as Follows ltem Parameter System Type Live View amp Recording Camera A single camera IP address of the camera 192 168 0 10 Camera group None Channel of the connected camera 1ch of WJ NT104 Disk space Not allocated Access mode Continuous User admin only Password Password entered when installing the WV AS710 Schedule None Alarm function None 41 After the Installation of the WV AS710 To run the network camera server after installation do the following E Mail System Establishment The network camera server can send e mail to registered e mail addresses when an alarm occurs To use this function establishment
7. Panasonic PC Software Package Operating Instructions Model No WV AS71 O Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use CONTENTS PEATURES sl ee ee eee 4 e er Ao 10 HOW to Use th TOP I csmisstanoenicrc brotar ee E Taa ta 12 How to Use the Camera Page ccccccssseecccceeceeesesceeeeeeeseeceeeeaeaeeeeeessseseeeeeessaaseeeeees 13 Camera Selection Menu scared 14 Picture Display Area siria ini voii dd 15 UI Mode FANE e EE roto aida 17 Playback of Recorded Pictures scnassescssnneccqeseseocceebstoontadenemecementeaesedanteinsmesenteganccenenennees 20 Searching Ment cesta id at 23 PIE MOda Panal ein EE E beosts a ccisa ias 27 Quad SGEN IEEE on A A 29 Installation of the MPEG 4 Plug in Software coooonccccnccccccoccnnnncnconononnncnnnnanonnnnnnnnans 30 Installation of the MPEG 4 Player cccoooonccccccoconccononcnncononnnnnononnnnnnnnncnnnnnnannnnnnnannanoss 31 INSTA io dios 32 Procedures to Establish the Network Camera Server c c cccccccseeeeeeeeeeeeeeeseeeeeeas 32 Selection OF the System Type cenas ia 33 Confirmation of the Directory Structure cccccccooncccnnccccconncnnnnononannnnnncnonanncnnnonononnnnnnnnns 34 Installation of Red Hat Linux scaner iic s 35 Allocation of Disk Space When Live View amp Recording is Selected 36 How to Allocate Disk Space cross of Installation of THE WV AS710 cc
8. e Adding the disk space e Deleting the disk space e Clearing the protected disk space Previous link text When the Recording Status List menu has two or more pages because many cameras are regis tered and the currently displayed page is not the first page this link text will be displayed Click this link text to display the previous page 99 Next link text When the Recording Status List menu has two or more pages because many cameras are regis tered and the currently displayed page is not the last page this link text will be displayed Click this to display the next page Disk Space Allocation for Camera Click the desired Camera No of the camera to which no disk space has been allocated yet in the Recording Status List menu The Disk Space Allocation for Camera menu will be displayed is the selected camera num ber Allocate the disk space for the selected camera on this menu Space To Be Allocated MB Disk Space Allocation for Camera 1 Enter the size of the disk space for the selected ee eae camera to be allocated as a designated size MB A A When another input box is clicked after entering the ia LN amount of disk space the entered size will be con verted into the respective percentage and the con verted value will be displayed in the input box Space To Be Allocated percentage of the disk space which can be used automatically Note It is impossible to enter a number bigger th
9. Alarm Notification menu When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to con firm Note If any other menu is displayed without click ing this button after editing the settings in the network camera server will not be updated E Mail Setting Click the E mail List link text on the Alarm Notification menu to display the E Mail Setting menu Up to 20 e mail addresses of recipients can be registered on this menu E Mail Setting 9 E DT TI CI oo ERA AAA A Setting Men th 11 wtish j JPC Save amp Go To Alam Notification E Mail Enter e mail addresses of recipients to which an alarm mail will be sent Up to 512 alphanumeric characters To delete an e mail address simply delete it from the input box Language Select the language used in the alarm mail The arrangement of the date will be different depending on the selected language Japanese Japanese Year Month Day American American English Month Day Year British British English Day Month Year Terminal Type Select the terminal type of the recipients The pic ture size differs depending on the selected terminal type GIF portable telephone Send an alarm mail to a portable telephone that can display GIF pic tures The picture size will be 120 W x 90 H pixels JPEG portable telephone Send an alarm mail to a portable telephone that can displ
10. Camera Setting tab The Camera List menu will be displayed It is useful to check the registered cameras with this page It is possible to register or delete cameras using this menu Note It is impossible to change the settings during recording Camera List a a Camera No Click the desired Camera No to display the Camera Properties menu of the desired camera Refer to page 49 for further information about the Camera Properties menu IP Address Enter the IP address of the selected camera It is possible to enter the FQDN Fully Qualified Domain Name of the selected camera When a camera uses an HTTP port except port number 80 to deliver pictures enter colon port number just after the IP address or the FQDN For example 192 168 0 50 85 Channel When the registered camera is connected to a net work interface unit WJ NT104 select the channel 1CH 4CH of the network interface unit used for the selected camera from this pull down menu When the registered camera is connected directly without a network interface unit WV NP472 WV NS320 WV NS324 WV NM100 select 1CH Unit Type Image Format Select the model of the connected camera and the image format of the camera picture that the camera delivers WJ NT104 JPEG When registering a camera con nected to WJ NT104 select this WV NP472 JPEG When registering a WV NP472 select this WV NS320 JPEG When registering a WV NS320 or WV N
11. Note Depending on the network environment drop frame may occur Therefore it may be impossible to play all frames Slow Play Click this button to play recorded pictures at slow speed Fast Play only for JPEG Click this button to play recorded pictures at high speed Reverse Play All Frames only for JPEG Click this button to play all frames of recorded pic tures in reverse Frames are played in 0 2 seconds intervals Playback will take longer than when click ing the Reverse Play button Note Depending on the network environment it may take long to play all frames Previous Frame only for JPEG Click this button to display the previous frame This button works only when the currently displayed recorded picture is paused Next Frame only for JPEG Click this button to display the next frame This but ton works only when the currently displayed record ed picture is paused Pause Click this button to pause playback To stop paus ing click this button again When pausing is stopped the recorded picture will resume being played in the same way as before the recorded pic ture was paused by clicking this button For exam ple after clicking this button to pause playback dur ing Reverse Play the playback of the recorded picture will start again in Reverse Play by clicking this button again 20 Operation Play All Frames only for JPEG Click this button to play all frames of recorded pic tur
12. The HTML documents delivered from the net work camera server contain JavaScript and commands to CGls When a PC is set to ignore these commands HTML documents may not be displayed correctly FEATURES Notes e When the traffic on the network is heavy When the transmission speed is slow or the traffic on the network is too heavy to receive image data it may be difficult to browse camera pictures and a still picture indicating the failure to acquire an image Image capture has failed may appear When this still picture appears frequently adjust the time interval for acquiring image data e When a firewall including software is installed e Allow HTTP access to a port for Apache default port number 80 e Allow HTTP access to a port for WV AS710 default port number 8080 The port for WV AS710 can be changed during installation e Allow access to all of the UDP ports Otherwise it is impossible to browse motion pictures MPEG 4 E Standard Accessories TOI are iria ei 1 aclaro ia 1 Hardware KOY A o nen 1 CD ROM includes the install program of the WV AS710 the operating instructions PDF and the Readme txt Before installation read the Readme txt E Trademarks and Registered Trademarks Linux is a registered trademark of Linus Torvalds RED HAT is a registered trademark of Red Hat Inc Java is a trademark or registered trademark of Sun Microsystems Inc in the United States and other countries Microsoft Windows and Wi
13. WV AS710 MPEG 4 Player Searching Menu Time amp Date Search Search recorded pictures saved in the network camera server by designating a camera number date and time How to display the Time amp Date Search Click the Time amp Date Search tab Note The authentication dialog window will be displayed when a user tries to access a camera which the user is not allowed to access In this case cancel the operation or enter a valid user name and password to be allowed to access and operate the selected camera V AS710 Camera Time amp Date Select Search Event Search i Day 131 y Month 3 y Year 2003 Hour 119 Minute 36 V Show Thumbnail SEARCH Copyright 2003 Matsushita Electric Industrial Co Ltd All rights reserved Camera Number Enter the desired camera number whose pictures are to be searched in this input box When it is required to enter two or more camera numbers insert a comma between the camera numbers When the pictures of all cameras are to be searched enter an asterisk Note When a camera number without disk space allocation for recorded pictures or a camera number that the user is not allowed to access is entered an error message will be displayed Month Day Select the month and day to be searched Year Enter the year to be searched in this input box with 4 digits An error message will be displayed if the SEARCH b
14. camera picture is not possible The range of pan ning and tilting by one click differs depending on the distance between the center point and the clicked point For example if you click the right edge the camera pans widely toward the right side Tilting is performed in the same way as pan ning The camera will not move if the clicked point is just around the center point Notes Even if a point on the camera picture or the arrow buttons of Pan Tilt is kept pressed the camera will not keep on moving e Panning and tilting is possible only when one of the following cameras Is selected e Camera connected by the network interface unit WJ NT104 e WV NM100 e WV NS320 WV NS324 Auto Pan Click the ON button to start the AUTO functions set on the cameras AUTO PAN SEQ SORT PATROL and so on The available functions differ depending on the settings of the cameras Refer to the operating instructions of the cameras for further information The way of panning differs depending on the model of the selected camera Click the OFF button to stop the AUTO functions Clicking other buttons except the O button or the F button of Manual Recording also stops the AUTO functions Scan When the PRESET TOUR button is clicked the cam era Starts touring the preset position number 1 to 8 in numerical order and stops automatically When the ONE TIME PAN button is clicked the cam era starts panning once to the right end and on
15. not when an alarm occurs at the camera site Notes e Priority of alarm recording is 3 and cannot be changed e In the case where disk space is not allocated to a camera at which an alarm occurred or when disk space for the camera is full it will not be possible to record alarm pictures To record alarm pictures it is required to vali date Panasonic Protocol for cameras or net work interface unit and it is also required to register the IP address of the network camera server as recipient It is possible to notify through TCP IP only when devices transmitting Panasonic Protocol and the network camera server are IP reachable lt is not possible to record alarm pictures by the internal alarm of a camera connected to a net work interface unit It will be impossible to identify which camera is transmitting an alarm signal if a router is installed between a camera site and the net work camera server and when sharing an IP address at the center site for two or more cam eras using network address translation In this case the network camera server will regard the camera with the lowest camera number as the camera transmitting the alarm signal Select how many seconds before an alarm occurs the network camera server starts recording When recording in the JPEG format alarm pictures will be recorded at the selected interval for Interval JPEG Mode Only When pictures are recorded in the MPEG 4 format recording interva
16. the user authen tication dialog window will be displayed In this case perform the authentication as an Operator or as an administrator Note The authentication dialog window will be dis played when a user tries to access a camera which the user is not allowed to access In this case can cel the operation or enter a valid user name and password to be allowed to access and operate the selected camera About camera control lt is impossible to operate the camera if another user is currently operating it it is possible to access the selected camera only to view live pictures When the selected camera is a WV NS320 WV NS324 or a camera connected by the network inter face unit WJ NT104 Manual Recording Auto Pan Preset Paw Tilt pn p Zoom Focus F Iris Note The operable buttons will depend on the fea tures of the camera connected by the WJ NT104 When the selected camera is a WV NM100 Paw Tilt sal al _ en Manual Recording z Scan Preset Brighiness paan Se sl cl sol col ol col ee sera When the selected camera is a WV NP472 Manual Recording Live View 8 Recording Click the 0 button to record the currently monitored camera picture on the hard disk of the network camera server If the camera picture is recorded in the JPEG format the camera picture will be recorded at 1 fps JPEG until the button is clicked If the camera pic ture is recorded in the MPEG 4 format the camer
17. 1 128 Live View Only Click one of the Camera Select buttons The camera picture respective to the clicked button appears in the picture display area NEXT button Click this button to display the Camera Select buttons for the next sixteen cameras When the Camera Select buttons are displayed in the list form clicking this button displays the Camera Select buttons for the next four cameras PREV button Click this button to display the Camera Select buttons for the previous sixteen cameras When the Camera Select buttons are displayed in the list form clicking this button displays the Camera Select buttons for the previous four cameras GO button Enter the desired camera number in the input box next to this button and click this button to display the camera picture respective to the entered cam era number in the picture display area Note When a camera delivering camera pictures in the MPEG 4 format is selected the dialog window below may be displayed Microsoft Internet Explorer X aN Loading MPEG 4 decoder Failed Check the installation This window will be displayed if the MPEG 4 Plug in Software is not installed to browse MPEG 4 motion pictures on a web browser Refer to the MPEG 4 Plug in Software Installation on page 30 Quad Screen Button Click this button to change the single screen in the picture display area to the quad screen Up to four camera pictures are displayed simult
18. MPEG 4 Plugin Download button Follow the displayed instructions to download the installer Setup exe 3 Double click the installer Setup exe to start installation The installer will start up Follow the displayed instructions to complete installation How to Uninstall To uninstall the MPEG 4 Plug in Software do the following Except Windows XP 1 Open the control panel Start Settings Control Panel The control panel will be opened 2 Double click the Add Delete Application 3 Select MPEG 4 Viewer Software and click Change Remove 4 Follow the displayed instructions to complete uninstall In Windows XP 1 Open the control panel Start Control Panel The control panel will be opened 2 Double click the Add Delete Application 3 Select MPEG 4 Viewer Software and click Change Remove 4 Follow the displayed instructions to complete uninstall 31 Installation of the MPEG 4 Player To play downloaded recorded pictures in the MPEG 4 format it is required to install the MPEG 4 Player on the PC Notes e Confirm your PC fulfills the system requirements before installing the MPEG 4 Player Refer to page 7 for further information e The MPEG 4 Player is not compatible with Windows NT e Install or uninstall the MPEG 4 Player after logging on to the PC as an administrator Administrator Windows 2000 Computer Administrator Windows XP How to Install To install the MPEG 4 Player do the
19. Maximum frame rate of WJ NT104 5fps Settings of WJ NT104 JPEG Fixed Input Selection Mode no limitation for maximum bit rate QVGA Maximum frame rate of WJ NM100 MPEG 4 30fps Settings of WV NM100 bit rate of 256kbps or more QCIP 2 In the case where the user site obtains 64 accesses for playback up to 36 accesses for viewing live pictures are available 34 Installation Confirmation of the Directory Structure The network camera server uses the following directories Disk space for recording pictures should be allocated by an administrator Refer to page 36 The other directories below are created automatically when the WV AS710 is installed Notes e The path of the directory to store the html documents and the CGI files will depend on the user environment e Do not change the directory name e Do not delete the files installed in each directory or change their names Directory name Description ust local s3 bin Executable files of the network camera server will be stored in this directory When the installation script is executed this directory will be automatically created lusr local s3 Setting files of the network camera server will be stored in this directory When the installation script is executed this directory will be automatically created HTMLPath s3 HTML documents will be stored in this directory When the installation script is exe cuted this directory will be automatically created CGIPath s3
20. The blue still picture is dis played Cannot perform preset oper ations The camera does not return to the home position Cannot play Cannot record Cannot search No result is displayed when searching by the recording time The played picture is not displayed The camera number and the time are not displayed when monitoring the played picture Cannot record any more Points to be checked Solutions Is the power of the camera on Is the power of the network interface unit on Is the Active selected on the Camera Sleep Schedule Properties menu Is it possible to establish the transmission between the network inter face unit and the network camera server Confirm it using ping com mand Are the IP address of the network interface unit and the channel of the camera correct Is the ON selected for the authentication of the network interface unit If it is enter the valid user name and password When using a line with slow data transmission rate such as analog lines it may rarely happen that a still picture is displayed If this hap pens select a slower interval for the Interval of the System Properties menu Does the camera have the preset function Is the preset position setting performed also for the camera not only for the software Does the camera have the preset function Is the home position setting performed also for the camera not only for the software Is the user authenticate
21. following 1 Display the TOP MENU of the network camera server http server address s3 British The server address differs depending on the user environment 2 Click the MPEG 4 Player Download button Follow the displayed instructions to download the installer Setup exe 3 Double click the installer Setup exe to start installation The installer will start up Follow the displayed instructions to complete installation When the MPEG 4 Player has been installed the MPEG 4 Player will be added to the Start menu in Windows Except Windows XP Programs WV AS710 MPEG 4 Player WV AS710 MPEG 4 Player In Windows XP All Programs WV AS710 MPEG 4 Player WV AS710 MPEG 4 Player How to Uninstall To uninstall the MPEG 4 Player do the following Except Windows XP 1 Open the control panel Start Settings Control Panel The control panel will be opened 2 Double click the Add Delete Application 3 Select WV AS710 MPEG 4 Player and click Change Remove 4 Follow the displayed instructions to complete uninstall In Windows XP 1 Open the control panel Start Control Panel The control panel will be opened 2 Double click the Add Delete Application 3 Select MPEG 4 Viewer Software and click Change Remove 4 Follow the displayed instructions to complete uninstall 32 Installation To install the WV AS710 adequate knowledge of Red Hat Linux is required Also adequate k
22. for each registered camera will be displayed automatically it is calculated by dividing the total available disk space by the number of the regis tered cameras Entering the desired size in Megabytes in the Disk Space input box is also possible In this case when another input box is clicked the Total will be recalculated automatically Total Total disk space that can be allocated for the regis tered cameras will be calculated and displayed here Available Space Available space will be displayed Execute button Click this button to start formatting and allocation When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to complete Note If any other menu is displayed without click ing this button after editing the settings in the network camera server will not be updated 01 Administration Recording Schedule List Click the Recording button of the Setting Menu to display the Recording Schedule List menu or click the Recording Schedule tab The Recording Schedule menu will be displayed It is useful to check the recording schedules with this page The Recording Schedule is the function to record camera pictures automatically at designated times Up to 20 schedules can be registered Active schedules will be displayed in black and inactive schedules will be displayed in red Setting Menu L Vii NON
23. from the cameras belonging to the same group Monitor A user of this user type only can view live pictures and perform the preset operations of the cameras belonging to the same group User Authentication A user can operate cameras or functions only when the user is authenticated When selecting a camera for which the user is not authenticated the authentication dialog window will be displayed Enter a registered user name and a password to be authenticated for the selected camera or cancel 09 User List Click the User Camera Group button of the Setting Menu or click the User Setting tab to display the Recording Schedule List menu The User List menu will be displayed It is useful to check the registered users with this page Note At least a user has to belong to the admin group as an administrator If no user belongs to the admin group it will be impossible to administrate the network camera server since no user can access the administration menus As a default setting a user user name admin group admin is already registered password is the one entered when installing the WV AS710 User Registration button To register a new user click this button to display the User Registration menu and do it on that menu User Name The list of registered user names will be displayed To change a user profile password Group User Type or delete a user from the user list click the required user name to dis
24. is unnecessary to create disk space or when adding disk space later for example installing a new hard disk later enter n Unmounting the CD ROM When the installation of the WV AS710 on Red Hat Linux has been completed enter the following commands to unmount the CD ROM Hcd umount mnt cdrom Starting up the Network Camera Server Installation of the Hardware Key The WV AS710 will not be started up if the provided hardware key is not installed on the PC server Before starting up the WV AS710 insert the provided hardware key into a USB port on the PC server It is also possible to insert the hardware key into a USB hub connected to the PC server Start up from the Administrator s Page After the installation of the WV AS710 the first startup of the WV AS710 can be made using the Administrator s Page To display the Administrator s Page click the Administrator s Page button on the TOP MENU page TOP MENU page address http server address s3 American http server address s3 British The server address differs depending on the user environment When the authentication dialog window is displayed enter admin for user name and the password entered when installing the WV AS710 Installation When the network camera server has not yet started up the server start confirmation page will be displayed Click the Start WV AS710 button to start up the WV AS710 Start WWV AS5710 Setting Menu
25. password entered in the Password input box above for confirmation Group Admin Users who administrate the network camera server administrators are required to belong to this group All users belonging to the admin group can operate all cameras record search play recorded pictures preset operation and administrate the network camera server by accessing the Administrator s Page Group 1 20 These groups are for general users to access the network camera server to browse live cam era pictures or operate cameras What users can do while accessing cameras differs depending on the user type Users belong to these groups cannot access the Administrator s Page Note The names of groups can be changed on the Group Name menu User Type Select a user type for the user from Operator or Monitor Refer to the Authentication on page 66 for information about what users can do when accessing cameras When a user belongs to the admin group settings for the User Type will be ignored Save button Click this button to save the new profile When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to confirm Note If any other menu is displayed without click ing this button after editing the settings in the network camera server will not be updated Delete button Click this button to delete the selected user When this button is clicke
26. work camera server is running the latest regis tered schedule will be applied e When a schedule is registered just after the net work camera server has started up the sched ule with higher schedule number will be applied Comments Comments about schedules will be displayed 92 Administration Camera Sleep Schedule Properties Click a desired No on the Camera Sleep Schedule List menu to display the Camera Sleep Schedule Properties menu Perform the settings for the selected camera sleep schedule or delete the selected camera sleep schedule Camera Sleep Schedule W j y ra Setting Menu Camera Sleep Schedule Properties Schecdde wal not be etfectrre unless you dick the Save button Delete Schedule Osten Camera Slasp Schedule List Schedule No The schedule number is indicated Active Inactive Active Select this to activate the selected sched ule Inactive Select this to inactivate the selected schedule From Select the day hour and minute increments of 5 minutes from the pull down menu time for the start time of the selected schedule Day Monday Tuesday Wednesday Thursday Friday Saturday Sunday Mon to Fri Sat and Sun Daily Hour 0 23 Every Minute 0 5 10 15 20 25 30 35 40 45 50 55 min Every Note To activate Camera Sleep Schedule for 24 hours select Daily for Day Every for Hour and Every for Minute Select the day hour and
27. 31 03 2003 19 45 05 Contact Alarm Camera 5 31 03 2003 19 45 01 Contact Alarm Camera 5 31 03 2003 19 44 57 Contact Alarm New Event Data Click the desired event Result List Thumbnail ee a p i eri Camera 5 31 03 2003 19 45 35 Contact Alarm Camera 5 31 03 2003 19 45 33 Contact Alarm mila o Mee Camera 5 31 03 2003 19 45 16 Contact Alarm Camera 5 31 03 2003 19 45 14 Contact Alarm The selected recorded picture will be played from the point of the entered time and date Events in which the respective recorded picture has already been deleted and events of Image Acquisition Loss will not be played since they do not have any recorded picture Notes e When the time on the clocks of the network camera server and the PC do not match searches will not be performed correctly e When pictures are recorded in the MPEG 4 format the dialog window below may be displayed Microsoft Internet Explorer X aN Loading MPEG 4 decoder Failed Check the installation This window will be displayed if the MPEG 4 Plug in Software is not installed to browse MPEG 4 motion pictures on the web browser Refer to the MPEG 4 Plug in Software Installation on page 30 2 Play Mode Panel The play mode panel contains the buttons to play recorded pictures in various ways How to Display the Play Mode Panel The play mode panel will be displayed when the desired recorded picture i
28. Alarm Notification E Mail Setting Performs the settings for how the Registers e mail addresses of recipients for alarm mail network camera server informs of an alarm occurring Stop and Restart Stops or restarts the WV AS710 TOP MENU Goes to the TOP MENU EXIT Exits from the Administrator s Page and closes the browser window system Type Click the System Type button on the Setting Menu The Select System Type menu will be displayed Select Live View amp Recording or Live View Only from the pull down menu When selecting Live View amp Recording allocating disk space Is required in advance Live View amp Recording Select System Type lt is possible to record camera pictures on disk space for recorded pictures Disk space allocation is required in advance Live View Only Only delivery of live pictures is available with this system type Recording playback searching and rare Vero VEIA alarm function are not possible with this system 7 type Save button Click this button when the system type is changed The dialog window for confirmation will be dis played Click the OK button on the dialog window to confirm After clicking the OK button restart the WV AS710 to make the changed system type valid Setting Menu System Type Select the system type of the network camera server 4 Camera Setting Camera List Click the Camera button on the Setting Menu or click the
29. CGI files to be used for administration will be stored in this directory When the installation script is executed this directory will be automatically created var run Process ID files will be created in this directory When the installation script is exe cuted this directory will be automatically created var log s3 Log files such as an alarm log file and an access log file will be created in this direc tory When the installation script is executed this directory will be automatically cre ated var s3 etc Administration information of the disk space for recorded pictures will be stored in this directory When the installation script is executed this directory will be automati cally created var lib mysql The database will be stored in this directory This directory will be used by the database server S3_DATAxx When Live View amp Recording is selected for the system type this directory will be required xx two digits number e g S3_ DATAO0 S3_ DATA01 etc The net work camera server will use this as the disk space for recorded pictures It is required to allocate disk space for this as a partition when installing Red Hat Linux To allocate disk space for this after installing Red Hat Linux an administrator has to allocate disk space for this manually It is possible to use up to 16 disks for this directory Refer to the page 36 for further information 35 Installation of Red Hat Linux When installing Re
30. MENU page and installing it Help button Click this button to display the Help page Administrator s Page button Click this button to display the Administrator s Page Only users registered in the administrator group can display the Administrator s Page The user name and password registered to the adminis trator group will be required Refer to the Administration section of these operating instruc tions Refer to page 43 for further information MPEG 4 Plug in Download button Click this button to display the MPEG 4 Plug in Software download page The MPEG 4 Plug in Software is required to browse MPEG 4 live cam era pictures using a web browser MPEG 4 Player Download button Click this button to display the MPEG 4 Player download page The MPEG 4 Player is required to play downloaded MPEG 4 pictures stored on the network camera server 13 How to Use the Camera Page To operate the Camera Page refer to the following To display the Camera Page click one of the avail able camera buttons on the TOP MENU page Click a tab to change the operation menus Menu Picture Display Area e When IP addresses of cameras registered to the network camera server are incorrect When a camera registered to the network camera R server is not connected TA oe AS 1 hae eee A E ROME A y 7 PA ii a When the network camera server cannot acquire camera pictures because of connection trouble a s malfunct
31. PEG 4 Player is required To download the MPEG 4 Plug in Software and the MPEG 4 Player it is required to agree to the License Agreement In the WV AS710 32 licenses are included Each time the MPEG 4 Plug in Software or the MPEG 4 Player is downloaded one license is used When accessing the network camera server with two or more browser windows of a web browser on a PC pictures may not be displayed correctly To access cameras with an operating restriction the user is required to be registered for authentica tion Refer to an administrator for a user name and a password These operating instructions explain about the HTML documents installed when the WV AS710 is installed If the HTML documents are edited lay outs and actions may be changed Access to the Network camera server Perform the following to access the network camera server to browse camera pictures 1 Start up the web browser and enter one of the fol lowing URLs refer to a system administrator or a network administrator about the URL e Display in English Date format Month Day Year http address of server s3 American e Display in English Date format Day Month Year http address of server s3 British e Display in Japanese http address of server s3 Japanese When an address is entered correctly the TOP MENU will be displayed Help ihvlniicreator s Pape E Le MPFECGA lich Merandavl il eo FI ayer aria EET Note In th
32. S324 select this WV NM100 JPEG When registering a WV NM100 delivering JPEG camera pictures select this WV NM100 MPEG 4 When registering a WV NM100 delivering MPEG 4 camera pictures select this Title Up to 16 characters Assigning a title to the camera is available Operating Restriction Select one of Unrestricted View And Preset Only or By Camera Group Setting to restrict users access to the camera or not Unrestricted When Unrestricted is selected all users Can access and operate the camera except for recording View And Preset Only Browsing live pictures and preset operations are possible By Camera Group Setting Register a camera to groups using the Camera Group Setting page first User Camera Group button Camera Group Setting tab The Operator type users belonging to the group can operate this camera including for recording The Monitor type users belonging to the group only can view live pictures and preset operations The other users cannot operate this camera at all Note Basically recording pictures can be done only by administrators When By Camera Group Setting is selected the Operator type users also can record pictures 48 Administration Unit Setting Click the Setup button to display the setting menu html of the camera Available settings are differ ent depending on the connected camera Refer to the operating instructions of the connected camera for furth
33. T Camera Page 1 64 when Live View amp Recording is selected as the System Type 1 128 when Live View Only is selected as the System Type Camera numbers will be displayed The available camera numbers are of cameras registered to the network camera server When an available button is clicked the picture from the selected camera will be displayed in the selected camera page The camera number buttons are different depending on the selected system type of the network camera server as follows Live View 8 Recording 1 64 Live View Only 1 128 Notes Live camera pictures will not be displayed even when an available button is clicked in the following cases When the network camera server stops delivering camera pictures temporarily The network camera server stops delivering camera pictures during Camera Sleep Schedule Refer to page 51 for fur ther information about Camera Sleep Schedule When IP addresses of cameras registered to the network camera server are incorrect When a camera registered to the network camera server is not connected e When the network camera server cannot acquire camera pictures because of connection trouble malfunctioning of cameras etc Even if MPEG 4 Plug in Software is not installed on a PC the network camera server will deliver MPEG 4 camera pictures In this case this prob lem will be solved by downloading MPEG 4 Plug in Software from the TOP
34. The groups Group 1 Group 20 are for general users When By Camera Group Setting is selected for Operating Restriction on the Camera Properties menu of a cam era only users belonging to the same group can access the camera Even if users belong to the same group what users can do with access to cameras differs depending on the user type A camera can belong to two or more groups Note The Administrator s Page cannot be accessed using a user name and a password assigned to a user belonging to a general group Administrator group admin Only users belong to the administrators admin can display the Administrator s Page An administrator has to belong to the admin group If no user belongs to the admin group it will be impossible to administrate the network camera server since no user can access the Administrator s Page All users belonging to the admin group can operate all cameras record play recorded pictures and administrate the network camera server by accessing the Administrator s Page Restrictions There are the following group restrictions e A user cannot belong to two or more groups When a user needs to access cameras belonging to two or more groups the user is required to be registered in each group with different user names to access these cameras e To assign the camera to a group select By Camera Group Setting for Operating Restriction in the Camera Properties menu of the selected c
35. a pic ture will be recorded at the transmission rate of the camera until the F button is clicked The Priority of manual recording is 4 and pictures recorded by man ual recording will be stored in the protected disk space Notes When pictures are recorded in the JPEG format recording interval may differ as below e If a recording whose priority is higher than the man ual recording priority for example alarm recording priority 3 or a schedule recording whose priority is set to 1 2 or 3 and whose recorded pictures are set to be stored in the protected disk space is performed during manual recording pictures will be recorded at the recording interval of the recording whose priority is the highest 16 Operation e If manual recording and a recording whose priority is the same as the manual recording for example schedule recording whose priority is set to 4 and whose recorded pictures are set to be stored in the protected disk space are performed pictures of the recording that started later will be recorded at its recording interval Depending on the setting of Minimum Access Interval Maximum Frame Rate the recording inter val will be different from the examples above Refer to page 63 for further information To stop recording click the F button Notes Manual recording will be stopped in the following cases lt is impossible to stop recording by closing the window of a web browser or by shutting do
36. a previous group page exists this link text will be displayed Click this link text to display the previous group page Next link text When a next group page exists this link text will be displayed Click this link text to display the next group page 73 Group Name Click the User Camera Group button of the Setting Menu and click the Group Name tab to display the Group Name menu Note Addition or deletion of a group is impossible Setting Menu ami mid Gi i J New group name well mothe efect unless you chri the Save butan No The number of the group is indicated There are 1 to 20 and admin Group Name The current group name will be displayed New Group Name Enter a desired new group name of up to 32 alphanumeric characters Save button Click this button to save the new group name When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to confirm Note If any other menu is displayed without click ing this button after editing the settings in the network camera server will not be updated 14 Administration Perform the following system settings of the network camera server Stop or restarting the WV AS710 is also possi ble e System Properties Pre Authentication Setting Camera Control Setting Network Setting Monitor Screen Setting Auto Erase Setting e Alarm Notification e Stop and Restart Syst
37. alled between the camera site and the network camera server and when sharing an IP address at the center site for two or more cameras using network address trans lation NAT In this case the network cam era server will regard the camera with the lowest camera number as the camera trans mitting the alarm signal Notify alarm image acquisition loss Send e mail to the registered e mail addresses in the E Mail Setting menu when an alarm occurs at a camera site or if it fails to acquire camera pic tures Notify alarm Send e mail to the registered e mail addresses in the E Mail Setting menu when an alarm occurs Notify image acquisition loss Send e mail to the registered e mail addresses in the E Mail Setting when it fails to acquire camera pictures Do not notify Do not send e mail What is image acquisition loss When the network camera server cannot acquire pic tures from a camera site the network camera server regards it as image acquisition loss The image acquisition loss may happen when a camera is mal functioning the power of the camera is off breaking of wire connection trouble etc To Click the E mail List link text to display the E Mail Setting menu Enter e mail addresses of recipients on the E Mail Setting menu From Enter the e mail address of the sender of up to 128 alphanumeric characters 70 Administration Save button Click this button to save the settings of the
38. amera 68 Administration User Basically a user must belong to only one group among the 20 general user groups of Group 1 20 or the adminis trator group admin A camera can belong to two or more groups A user can access only cameras belonging to the same group Depending on the user type and the group to which the user belongs what the user can do with access to cameras differs There are two user types Monitor and Operator When a user is assigned to the general group Group 1 20 Users belonging to one of these groups can access a camera that belongs to the same group to view live camera pictures or to operate it When Unrestricted is selected for Operating Restriction on the Camera Properties menu of the selected cam era all users can access the camera to view live camera pictures and operate preset functions Note To prevent illegal access it is recommended to not select Unrestricted for Operating Restriction in the Camera Properties menu of all cameras When a user is assigned to the administrator group admin All users belong to this group administrators can operate all cameras record play recorded pictures preset opera tions and administrate the network camera server by accessing the Administrator s Page User Type There are two user types Operator and Monitor Operator A user of this type can view live pictures operate cameras record search and play recorded pictures
39. an the Available Disk Space Allocate button Click this button to format and allocate the disk space When this button is clicked a dialog window for confirmation will be displayed Click the OK button in the dialog window to complete Recording Status List link text Click this link text to return to the Recording Status List menu Available Disk Space The available disk space will be displayed Unit size MB Space To Be Allocated percentage of the available disk space which can be used Enter the percentage of the disk space for the selected camera to be allocated as a designated proportion When another input box is clicked after entering the percentage number the entered percentage will be converted into megabytes and the converted value will be displayed in the input box Space To Be Allocated MB automatically Administration Disk Space Setting for Camera Click the desired Camera No of the camera to which the disk space has already been allocated in the Recording Status List menu The Disk Space Setting for Camera menu will be displayed is the selected camera num ber This menu has the following links e Disk Space Addition link text e Delete Disk Space link text e Clear Protected Disk Space link text Reeceading Staten OUR TC AA LLE Alarm Ha cording Disk Space Setting for Camera 1 Disk Space Addition link text Click this link text to display the Di
40. aneously The Live Mode panel is not displayed when the quad screen is displayed Note This button appears only when the Quad Screen Button of Monitor Screen Setting on the System Properties menu is set to ON 19 Picture Display Area The live camera pictures are displayed in the picture display area in the single screen or the quad screen in the Live Mode When in the Play Mode recorded pictures stored in the network camera server will be displayed in the sin gle screen Single Screen Live Mode and Play Mode Quad Screen Live Mode Only VGA CIF button Click the VGA button to change the screen size to the VGA mode when displaying JPEGs When the selected camera delivers MPEG 4 click the CIF button to change the screen size to CIF mode QVGA QCIF button Click the QVGA button to change the screen size to the QVGA mode when displaying JPEGs When the selected camera delivers MPEG 4 click the QCIF button to change the screen size to the QCIF mode Camera camera number When the camera picture is displayed in the single screen the camera number of the displayed picture is displayed above the picture TITLE When the quad screen is displayed each picture is displayed with its respective title above Click the desired camera title to display the desired camera picture in the single screen Note TITLE can be edited on the Camera List or Camera Property m
41. ates cameras Alarm picture A picture captured when an alarm occurs Red Hat Linux Red Hat Linux 8 0 Professional Windows Microsoft Windows operating system Windows 2000 Microsoft Windows 2000 Professional or Microsoft Windows 2000 Server Windows XP Microsoft Windows XP Professional or Microsoft Windows XP Home Edition Notes e Names of buttons are between square brackets e g the OK button e Names of menus and items on menus are between double quotation marks e g the System Properties menu 10 Operation This section describes how to access the network camera server in order to browse camera pictures operate cameras and play recorded pictures Access the network camera server using a web browser If you don t have a recommended web browser download it from the distributor Refer to the Help menu of the web browser or to the web site of a distributor if you need to learn how to oper ate the web browser It is required to configure the web browser to accept cookies from the network camera server If the web browser is configured to Block All Cookies set it to Accept All Cookies If it is con figured to prompt you when a cookie is sent click the Allow button in the displayed dialog window To browse MPEG 4 pictures the MPEG 4 Plug in Software is required This Plug in Software is only for Internet Explorer 5 5 SP2 and 6 0 SP1 To browse downloaded MPEG 4 recorded pictures the M
42. ation will be displayed Click the OK button in the dialog window to confirm This button restarts only the WV AS710 Red Hat Linux will not restart with this button Notes e When it is needed to stop the WV AS710 use the Stop and Restart menu Confirm the mes sage Stop Server System is displayed e When forced termination is performed by press ing the Ctrl key and the C key simultaneously or entering the kill command pictures in the disk space may be broken When it is needed to stop the WV AS710 always use the Stop and Restart menu e During processing for example changing disk space for recorded pictures the WV AS710 will be unable to stop In this case try to stop after the WV AS710 finished any process Troubleshooting Troubles Symptoms Points to be checked Solutions e Is the message of Can t create s3 pid running already or permission Cannot start up the WV AS710 Failure to acquire pictures Cannot change the image size using the VGA QVGA CIF QCIF but tons Cannot operate the camera even though monitoring the pictures is possible Cannot select a camera using the Camera List menu Camera pictures do not change even though another camera Is selected denied displayed It seems that the WV AS710 multiply started Check if the WV AS710 is already started or not If the WV AS710 has not started yet the WV AS710 might have been forced to stop last time Check if s3
43. ay sGA QUGA Be LEE E a ES AN 4 al hee LA gt a A I3 AS A RA ces gt FS Start 31 03 2003 19 45 35 Stop 31 03 2003 20 15 35 DOWNLOAD When a search result is clicked the start time of the camera picture currently played will be displayed in the Start input box In the Stop input box the displayed time will be the start time plus 30 minutes Time to download can be changed by entering the date and time directly in the Start input box and in the Stop input box To download the recorded picture from the Start time to the Stop time up to 30 minutes on a PC click the DOWNLOAD button Note Download time will differ depending on the image format To download 30 minutes of recorded pictures approximately 100MB or more of hard disk space is required 17 Live Mode Panel The live mode panel contains the buttons to control the selected camera When the quad screen is displayed this panel is not displayed The buttons displayed in the live mode panel differ depending on the model of the selected camera How to display the live mode panel The live mode panel will be displayed by one of the fol lowing operations e Clicking one of the Camera Select buttons in the camera selection menu e Clicking the Live Mode tab in the live mode panel About the user authentication dialog window When a user who is authenticated as a Monitor user clicks a button in the live mode panel
44. ay Thursday Friday Saturday Sunday Mon to Fri Sat and Sun Daily Hour 0 23 Every Minute 0 5 10 15 20 25 30 35 40 45 50 55 min Every Note When Daily for Day is selected it is required to select Every for Hour and Every for Minute Camera No Enter the desired camera number to be used for the selected schedule When two cameras or more are used for this schedule insert a comma between the camera numbers When all cameras are used for this schedule enter an asterisk in this input box Data Protection Mode Select to protect the recorded pictures of the schedule saved as disk space or not Protect The recorded pictures will be saved in the protect ed area protected disk space in the disk space The recorded pictures will be protected until the recorded pictures are cleared from the Clear Protected Disk space for Camera menu is the selected camera number even if the formatting of the disk space is performed Overwrite The recorded pictures will be saved in the unpro tected area in disk space In this case the oldest recorded picture will be overwritten first when disk space is filled to capacity Interval JPEG Mode Only Select a recording interval from the pull down menu 0 066 Sec 15fps 0 1 Sec 10fps 0 2 Sec 5fps 0 5 Sec 2fps 1 Sec 1fps 2 Sec 3 Sec 5 Sec 10 Sec 30 Sec 60 Sec 120 Sec 180 Sec When pictures are recorde
45. ay JPEG pic tures The picture size will be 160 W x 120 H pixels PC Send an alarm mail to a PC The picture size will be the same size as the camera delivers Save amp Go To Alarm Notification button Click this button to save the settings of the E Mail Setting menu When this button is clicked the set tings of the E Mail Setting menu will be saved and the Alarm Notification menu will be displayed Note If any other menu is displayed without click ing this button after editing the settings in the network camera server will not be updated 19 Stop and Restart Click the System button of the Setting Menu to display the System Properties menu and click the Stop and Restart tab The Stop and Restart menu will be displayed To stop or restart the WV AS710 click the Stop or Restart button on this menu Setting Menu Stop and Restart When the syste ts deleting a disk space rciuding e camera entry iteal Stop after the process 15 completed Stop WV ASTIO Step Festal Wey AST EO Stop button Click this button to stop the WV AS710 When this button is clicked the dialog window for confirmation will be displayed Click the OK button on the dia log window to confirm Note This button stops only the WV AS710 Red Hat Linux will not be shut down with this button Restart button Click this button to restart the WV AS710 When this button is clicked the dialog window for confir m
46. can browse camera pictures in the MPEG 4 format by downloading the MPEG 4 Plug in Software from the network camera server and installing it in the PC Users also can download recorded pictures from the network camera server and play them as MPEG 4 motion pictures It is required to download the MPEG 4 Player to play downloaded pictures Download the MPEG 4 Player from the network camera server and install it in the PC Network Monitoring By using the network camera server users can browse JPEG or MPEG 4 format pictures from cameras at remote locations in the same way they access web pages using a web browser Multiple users can browse pictures from the same camera simultaneously and also each user can browse pictures from different cameras Recordings Authenticated users can record camera pictures delivered to the network camera server on to hard disks Alarm Recordings When the network camera server receives an alarm signal from a camera pictures from the camera can be record ed on to a hard disk when an alarm occurs In this case sending e mail to specified addresses to notify of an alarm occurring is also possible The recipients of the alarm mail can browse the recorded camera pictures by following a link contained in the mail Note The network camera server receives alarm signals only when cameras use the Panasonic protocol to transmit alarm signals Administration Administration of the network camera server for example setting o
47. ce to the left end and then stops automatically 19 Focus Click these buttons to adjust focusing Click the NEAR button to focus on a closer object Click the FAR button to focus on a farther object Click the AUTO button to focus on an object in the center of the displayed picture Note Even if the NEAR button or the FAR button is kept pressed the camera will not keep on focusing Iris Click these buttons to adjust the iris Generally to shoot images with a clear background or to shoot in bright locations the iris should be closed Click the OPEN button to open the iris so that the depth of field will be shallower Click the CLOSE button to close the iris so that the depth of field will be deeper Click the RESET button to return to the default depth of field Note Even if the OPEN button or the CLOSE but ton is kept pressed the iris will not keep on open ing or closing Brightness Click these buttons to adjust the brightness of the cam era picture Clicking the left side buttons makes the camera picture darker and clicking the right side buttons makes the camera picture brighter Play Mode tab Click this tab to switch from the Live Mode to the Play Mode manually 20 Operation Playback of Recorded Pictures When Live View amp Recording is selected as the system type of the network camera server the following recorded pictures will be stored in the allocated d
48. condition input link text 3 Click a link text or a thumbnail from the results The playback of the recorded picture will start Users can operate buttons on the play mode panel to play recorded pictures About playback of recorded pictures Playback of recorded pictures is possible only when Live View amp Recording is selected as the system type of the network camera server When a user who is authenticated as a Monitor user clicks a button in the play mode control frame the user authentication dialog window will be displayed In this case perform the authentication as an Operator or as an administrator or click the Cancel button in the user authentication dialog window Camera Play 84 MGA EAS s 2 eee ON 7 a y A 3 E tan A 2 Pa Start 31 03 2003 19 45 35 Stop 31 03 2003 20 15 35 Fast Reverse Slow Reverse To Oldest Play Play Reverse Play Play Slow Play Fast Play Te Latest Reverse Play Previeus A Next F Play All AD Frames Frame Frames PT TA p PT pr 21 Downloading Recorded Picture It is possible to download the recorded pictures onto a PC by designating the start time and stop time for downloading 1 Play a recorded picture and confirm the date and time to download 2 Enter the desired time for the Start time and Stop time lt is possible to download recorded picture of up to 30 minutes When playback starts the start time of the recorded pictur
49. cswicccccecnecesesactsaenosesehacsdedacteninaniestandesdactadatescotsacsedacenscsens 38 Starting up the Network Camera Server ccccccccccsessesceeeeeeeeseeeeeeeeaeeseeeeseseeaeeeeeeeeaas 39 After the Installation of the WV AS710 occccocccncccccncocccnncconononononcnoncnnonannnnonnnnnonnnnnnnnnos 41 Stop the WV AS710 oocococccccnnnccnnnoncnnnncnnnnnncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnrnnnneninnnns 41 ORIO VAIN IOI iaa co nico 42 AQUI ON tna irene cae sect 43 How to Display the Administrator s Page vnincianivcrcdid cdo dea 43 o AREA eiia 45 VENETIE ar A E E EE AE EE AE E E 46 eo 47 AMAT PO SNS suena E redes 49 Camera Sleep Schedule i ccicannccsnecrncdeennsvenenasciesnnetenecssenwacesetausgncendheciossncusheosuecencestes 51 Camera Sleep Schedule Properties ccccocoooncconncccoconcnnnnncnnnanncnnnnnnnannnononnonnnnnnnnnnns 92 Recording o ta US IST areas arrasan bera 54 Disk Space Allocation for Camera ooccccoococccnnnncncnonnnnnncnnnonnonnnnnononnnnnncnnnnnnnnnnnnonenanenns 55 Disk Space Setting for Camera o ccc05 cccccccccccccesseceeessssseeecececeeveeeceessecesseceasenctadeasees 56 Disk Space Addition for Camera occcccccncccccnnncccnnonconnnnnnnnnnonnnnnnnnnncnnnonnnnonnnnnnnonenanenss 57 Delete Disk Space for Camera soria ae 58 Clear Protected Disk Space for Camera ooooocccnnncccccnnccnnnncnnnannnnnnnnnonnncnnnnnononnnnnnnnns 59 Disk Space FIO Cal ON sirbe 60 Recording Schedule List
50. cture that the camera delivers WJ NT104 JPEG When registering a camera con nected to WJ NT104 select this WV NP472 JPEG When registering a WV NP472 select this WV NS320 JPEG When registering a WV NS320 or WV NS324 select this WV NM100 JPEG When registering a WV NM100 delivering JPEG camera pictures select this WV NM100 MPEG 4 When registering a WV NM100 delivering MPEG 4 camera pictures select this Pre Recording Select Allowed or Denied to activate the pre recording or not When Allowed is selected the network camera server will record camera pictures just before an alarm occurs Pre recording duration can be select ed in the Alarm Recording menu Note Pre recording duration cannot be set differ ently for each camera Save button Click this button to save the edited settings When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to update the settings Note If any other menu is displayed without click ing this button after editing the settings in the network camera server will not be updated Save amp Next Camera button Click this button to save the edited settings and go to the Camera Properties menu of the next cam era When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to update the settings Camera List link text
51. d the dialog window for confir mation will be displayed Click the OK button in the dialog window to confirm Display the User List menu and check that the deleted user is not in the User List menu User List link text Click this link text to return to the User List menu Administration Camera Grouping Click the User Camera Group button of the Setting Menu and click the Camera Group Setting tab to display the Camera Grouping menu Assign cameras to groups on this menu Note Assignment of a camera to a group using this menu is possible only when By Camera Group Setting is selected from the Camera Properties menu of the selected camera Check boxes will be displayed on this menu Setting Menu Camera Grouping Group IAS AAA E AA E O E DE pi e VE mw ERE ae A A Fa Fak Pa Pea a a_i Sea ee ee aS ae ae a a ae fae O Ea EE pp Pt Bea CE EAN Far a fee Feo Fer ez es 6 Camera 1 64 1 128 Assign cameras to desired groups Only cameras with the check box can be assigned The number of cameras differs depending on the selected sys tem type Save button When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to confirm Note If any other menu is displayed without click ing this button after editing the settings in the network camera server will not be updated Previous link text When
52. d Hat Linux take notice of the following About Disk Space for Recorded Pictures When Live View amp Recording is Selected When Live View amp Recording is selected as the system type allocation of disk space for recorded pictures will be required To allocate disk space for recorded pictures when installing Red Hat Linux use the following mount name S3_DATAxx xx 2 digit number Refer to page 36 for further information When it is required to allocate or add disk space after installing Red Hat Linux use the name above as the mount name Cautions when Installing Red Hat Linux It is recommended to install all the packages when selecting package groups during the installation of Red Hat Linux Selecting all packages using Custom Install can install all the packages included in Red Hat Linux The following packages are required to run the network camera server e Desktop Environment e Graphical Internet e Text based Internet e Server Configuration Tools e Web Server e Mail Server e DNS Name Server e SQL Database Server Click Detail to add mysql server e Network Server e Administration Tools Access the address below after completing installation and download and install an upgrade file to upgrade MYSQL to the latest version The address below is subject to change without notice https rhn redhat com errata rh8 errata html Installation Allocation of Disk Space When Live View amp Recording is Selec
53. d MPEG 4 file to MPEG 4 format it is required to install the MPEG 4 open it Player on the PC in advance File Menu Note Downloading the MPEG 4 Player is possible Open Select an MPEG 4 file to be played from the TOP MENU Refer to the Installation of Close Quit the MPEG 4 Player the MPEG 4 Player on page 31 Help Menu About Displays the MPEG 4 Player version Slider Move this slider to the desired point of play back using the mouse Pause Pauses the playback Click this button again to resume the playback Play Starts the playback Stop Stops the playback Wvy AS710 MPEG 4 Player File Help Slider 1 Move the downloaded self extracting executable file to the desired folder and then double click it When the downloaded self extracting file is double clicked MPEG 4 files file extension mg4 and an index file which includes information about the recording time etc file extension idx will be uncompressed in the selected folder Note Place the MPEG 4 files and the index file in the same folder If they are placed in different folders or the index file is deleted it may be impossible to play the MPEG 4 files 2 Start up the MPEG 4 Player When the MPEG 4 Player is installed the MPEG 4 Player will be added to the Start menu in Windows Except Windows XP Programs WV AS710 MPEG 4 Player WV AS710 MPEG 4 Player In Windows XP All Programs WV AS710 MPEG 4 Player
54. d in the MPEG 4 format recording interval differs depending on the trans mission speed of cameras Note When two or more recordings are performed or depending on the selected values for Interval and Minimum Access Interval Maximum Frame Rate pictures may be recorded at a different recording interval from the set value for Interval Refer to About Interval on this page for further information Priority The priority level 1 4 will be displayed 1 is the highest priority When two or more camera record ing schedules overlap the recording schedule with higher priority will be applied If the priority level is also the same priority will be decided as follows e When a schedule is registered while the net work camera server is running the latest regis tered schedule will be applied e When a schedule is registered just after the net work camera server has started up the sched ule with the higher schedule number will be applied Comments You can write comments about schedules Save button Click this button to save the settings of the Recording Schedule Properties menu When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to confirm Note If any other menu is displayed without click ing this button after editing the settings in the network camera server will not be updated Click the Cancel button to cancel to update setting
55. d to operate the camera If it happens even though authenticated refer to an administrator Do the clock both of the server and the PC have the exact time The search function refers to the clock of the network camera server When the clocks have different times the search function may work incorrect ly Synchronize both clocks Is the clock of the network camera server correct The network camera server refers to the clock of the server for recording Keep the right time for the clock of server Are the java applets JavaScript and ActiveX enabled Is the disk space full If it is back up the data and clear the protected disk space or add the disk space if necessary 82 Troubleshooting The registered address was not notified by e mail when an alarm occurred or after image acquisition loss The authentication dialog window keeps on being dis played even though it is cancelled each time The TOP MENU or the pages to browse the camera pictures cannot be dis played Cannot display a part of JPEG picture Cannot acquire camera pic ture Alarm function does not work correctly Points to be checked Solutions Is the Do not notify selected for the E Mail Mode of the Alarm Notification menu Is the mail system of the server activated correctly Check from the PC using the mail command if the network camera server is activated and confirm that mail can be delivered to the designated address Is th
56. e selected number the following picture will be delivered to users who accessed after it reached the maximum concurrent access limit aT Too much access Please try later Monitor Screen Setting Quad Screen Button Select ON to display the Quad Screen when the Quad Screen Button is clicked Select OFF to not use the Quad Screen When OFF is selected the Quad Screen button will not be displayed Transmission Mode When using cameras delivering MPEG 4 live camera pictures select either Unicast or Multicast to deliver MPEG 4 live camera pictures to a user site Unicast MPEG 4 live camera pictures will be deliv ered in unicast mode Multicast MPEG 4 live camera pictures will be deliv ered in multicast mode To use this mode set the LAN card eth0 on the PC server to the delivering side Note Pictures from cameras with operating restric tion will be delivered in the unicast mode Selecting Multicast will be ignored This set ting does not affect MPEG 4 acquisition Select the unicast mode on the setting menu of the camera delivering MPEG 4 Interval When using cameras delivering JPEG camera pic tures select an interval for acquiring pictures Very Fast Fast Middle Slow Very Slow When the network camera server and a user site is connected with a line faster than 100Mbps refer to the following picture size of all cameras are the same When the selected value for Inte
57. e Out If this mode is selected a user can operate a camera exclusively for a certain period of time Time Out Period and the other users cannot access the camera until the control time has passed Time Out Period Select an exclusive control time from the pull down menu for the Time Out 30 60 90 120 150 180 sec The selected value will be ignored when Exclusive is selected for the Mode of Camera Control Setting Network Setting Use a Proxy Server Select Use a Proxy Server with an IP address and a port number of a proxy server when the network cam era server acquires camera pictures via a proxy server from a camera site Enter colon port number just after an IP address For example 192 168 0 50 85 When camera pictures are not acquired via a proxy server select Bypass Proxy Server 9 Proxy Server Exceptions When a proxy server is used to capture camera pic tures enter the IP address of the network camera or the network interface unit when acquiring camera pic tures directly not via a proxy server When entering two IP addresses or more in this input box is required insert a comma between the IP addresses Maximum Concurrent Access Select a number for maximum concurrent accesses from the pull down menu 12 15 20 30 45 60 80 100 150 200 Only when Live View Only is selected for the sys tem type of the network camera server When number of accesses becomes more than th
58. e mail address correct Force the web browser to shut down The way to force termination is different depending on the OS Refer to the operating instructions of the OS Is the URL correct Is the Apache HTTP Server started up Is the description of the html document correct Is the description of the setting file for the Apache HTTP Server cor rect When using Internet Explorer 5 5 SP2 on Windows 2000 the bottom line part of the JPEG may not be displayed Upgrade the web browser to Internet Explorer 6 0 SP1 When a DDNS server is used it may happen if the IP address revision information is accessed before the DNS server updates it In this case using a static IP address is recommended Matsushita Electric Industrial Co Ltd Osaka Japan http www panasonic co jp global 2003 Matsushita Electric Industrial Co Ltd All rights reserved NO403 0 V8QA6138AN Printed in Japan
59. e network camera server from PCs Installation This section describes how to install the WV AS710 on a PC server on which Red Hat Linux 8 0 Professional is installed Administration This section describes how to set and administrate the network camera server Readers of This Manual The Operation section is written for users who know how to operate a web browser and have general knowledge about the Internet The Installation and Administration sections are written for users who know how to administrate Red Hat Linux 8 0 Professional and the Apache HTTP Server and who also know how to establish a backbone server Terms Meanings of the terms used in these operating instructions are as follows Network camera server A running PC server on which the WV AS710 is installed Network camera Cameras that can be directly connected to network such as WV NM100 WV NP472 WV NS320 and WV NS324 Disk space for recorded pictures Disk space used only for recording which is allocated on a mounted hard disk on the network camera server Partition or directory name is S3_ DATAxx PC A computer on which a Microsoft Windows operating system is installed Web browser Software to browse web sites on the Internet e g Netscape Navigator Internet Explorer etc Administrator A user registered in the administrator group User A person who accesses the network camera server using a web browser and browses camera pictures or oper
60. e unit here o0 Administration Access User Password In cases where user authentication is required to access the camera or the network interface unit enter the password registered for the camera or the network interface unit here Note It is required to enter the Access User Name and Access User Password when using WV NM100 WV NS320 or WV NS324 These are the user name and password regis tered to access the camera or the network inter face unit and are totally different from the user name and password required to access the net work camera server Some of the cameras may have an access level Depending on the entered Access User Name and Access User Password it may be impossible to operate some of the cameras from the network camera server Refer to the operating instructions of the cam era Access Mode Select an access mode from Continuous or On Demand Continuous The network camera server will keep on capturing pictures On Demand The network camera server will cap ture pictures only in the following cases e When a user selects a camera e When the start time of the recording schedule comes e When an alarm occurs Note When the alarm recording is set and Continuous is selected it may not start alarm recording until a connection has been complet ed from the moment that the alarm occurred Unit Type Image Format Select the model of the connected camera and the image format of the camera pi
61. e will be displayed in the Start time input box and the Start time plus 30 minutes will be displayed in the Stop time input box 3 Click the DOWNLOAD button Follow the displayed instructions It will take sever al minutes for the network camera server to pre pare the recorded picture to be downloaded Do not click any buttons until the network camera serv er completes preparation When download has been completed the down loaded file will be saved as a self extracting exe cutable file file extension exe When pictures delivered from a camera are in the JPEG format JPEG files and html documents will be downloaded as a self extracting executable file When pictures delivered from a camera are in the MPEG 4 format MPEG 4 files file extension mg4 and an index file file extension idx will be downloaded as a self extracting executable file Play Downloaded Recorded Picture To play the downloaded recorded picture do the fol lowing To play JPEG 1 Move the downloaded self extracting executable file to the desired folder and then double click it When the downloaded self extracting file is double clicked JPEG files file extension jpg and html documents used as a browser index html thumb html play html will be uncompressed in the select ed folder Notes e Browse the uncompressed JPEG files using the uncompressed html document index html e When the size of the picture delivered from the camera I
62. each connected camera is displayed Recording Status ASM The status of recording Alarm Recording Schedule Recording or Manual Recording of each connected camera is displayed Red Alarm Recording Blue Schedule Recording Black Manual Recording During recording becomes Allocated Space MB The allocated disk space for each connected cam era is displayed Unit size MB Used Space The used disk space for each connected camera is displayed as a bar graph The type of recording can be identified by the color of the bar graph Gray This color part is used by pre recording Red This color part is used as protected disk space by the network camera server When the protected disk space is cleared the red part will turn black Blue This color part is unprotected disk space of the network camera server Black This color part is unused disk space Pre Recording Time Sec The pre recording time recording time before an alarm occurs will be displayed This will be dis played only when both the following are executed e On the Camera Properties menu of the select ed camera Allowed is selected for Pre recording ON is selected for Recording and a value of Duration for Pre Recording is selected on the Alarm Recording menu Comments The status of the disk space for each connected camera is displayed The following comments will be displayed accord ing to the status e Formatting the disk space
63. ed Contact Alarm Check this box to search camera pictures recorded when an alarm occurred at a camera site VMD Alarm Check this box to search camera pictures recorded when motion was detected by the video motion detection function of cameras Manual Recording Check this box to search camera pictures recorded manually using Manual Recording on the Live Mode panel Image Acquisition Loss Check this box to search events including events in which camera pictures were not sent because of connection trouble network trouble malfunctioning of devices etc Include Non Video Event Check this box to search all events near the entered time and date even events whose record ed pictures have already been deleted from the network camera server or events without record ings such as an image acquisition loss Show Thumbnail Check this box to display a list of results with the respective pictures in small scale The MPEG 4 recorded pictures will not be displayed with the thumbnail in the list of results SEARCH button Click this button to start searching A list of up to ten pictures recorded near the entered time and date will be displayed as results Operation Result List Text Camera 5 The event near 31 03 2003 21 47 Camera 5 31 03 2003 19 45 35 Contact Alarm Camera 5 31 03 2003 19 45 33 Contact Alarm Camera 5 31 03 2003 19 45 16 Contact Alarm Camera 5 31 03 2003 19 45 14 Contact Alarm Camera 5
64. ed at a different recording interval from the set value for Interval Refer to page 63 for further information Data Protection Mode Select to protect the recorded alarm pictures saved on disk space or not Protect The recorded alarm pictures will be saved in the protected area protected disk space of the disk space The recorded alarm pictures will be protect ed until they are cleared from the Clear Protected Disk space for Camera menu is the selected camera number even if the formatting of the disk space is performed Overwrite The recorded pictures will be saved in the unpro tected area of the disk space In this case the old est recorded picture will be overwritten first when disk space is filled to capacity Save button 65 Click this button to save the settings of the Alarm Recording menu When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to con firm Note If any other menu is displayed without click ing this button after editing the settings in the network camera server will not be updated 06 Administration Authentication The network camera server authenticates users by user name and password There are 3 user types Administrator Operator and Monitor Users also must belong to a group among Group1 Group20 or admin Users belonging to admin are regarded as administrators Operable f
65. em Properties Click the System button of the Setting Menu or click the System Properties tab to display the System Properties menu Perform the basic settings of the network camera server Syriam Properties E EET Sp and Henri Use a Prciy Sarvar Bypass Prony Server Satting val not be facto unless you cick the Seve button Pre Authentication Setting Pre Authentication Mode Select OFF to not display the authentication dialog window until the authentication is required When ON is selected the authentication dialog window will be displayed when accessing a camera for the first time after a web browser started up In this case if an entered user name and a password are authenticated once the authentication dialog window will not be dis played until shutting down the web browser However the authenticated dialog window will be displayed when accessing a camera to which is not allowed to access or operate Camera Control Setting Mode Select Exclusive to allow a user to operate a camera exclusively Select Time Out to give a certain time period to operate a camera exclusively Exclusive If this mode is selected for example when user 1 accesses camera 1 the other users cannot access camera until user 1 accesses another camera To prevent continuous Exclusive mode the Exclusive mode will be released automatically 10 minutes after the user has finished operation of the camera Tim
66. ently No Protected Disk Space will be displayed Note All protected recorded pictures will be deleted when the protected disk space is cleared Pe ECT ik fence Allocation a A Alo Hecantng Clear Protected Disk Space for Camera 1 Setting Menu In 100 ME disk space Protec sk ect i 3 Ow sing appia 1 Cick the leer bution lo char ihe protected disk space bor camara Clear button Click this button to clear the recorded pictures in the protected disk space for the selected camera When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to complete Recording Status List link text Click this link text to return to the Recording Status List menu Disk Space Setting for Camera link text Click this link text to return to the Disk Space Setting for Camera menu 60 Administration Disk Space Allocation Click the Recording button of the Setting Menu and click the Disk Space Allocation tab The Disk Space Allocation menu will be displayed On this menu it is possible to allocate the same amount of disk space simultaneously to the selected cameras which no disk space has been allocated yet IET OT Dhek Space Alacan EA Maem Aeconding Disk Space Allocation Setting Menu Camera No Check the box to select cameras requiring alloca tion of disk space Disk Space After this menu is displayed the available disk space
67. enu by an administra tor TITLE will not be displayed if it has not been entered Live Play Live View 8 Recording When a live camera picture is displayed in the sin gle screen Live is displayed above the picture When a recorded picture is displayed in the single screen Play is displayed above the picture Note When the quad screen is displayed neither Live nor Play appears NEXT button This button appears when camera pictures are dis played in the quad screen Click this button to dis play the camera pictures for the next four cameras in the quad screen PREV button This button appears when camera pictures are dis played in the quad screen Click this button to dis play the camera pictures for the previous four cam eras in the quad screen 16 Operation When failure to acquire a camera picture occurred When the network camera server could not acquire a camera picture the picture below will be displayed Image capture has failed When the network camera server could not acquire a camera picture it is possible to send an e mail to an address registered in advance to notify of this failure Although access to acquire camera pictures failed the network camera server retries to acquire pictures peri odically When also retrying to acquire camera picture fails notification by e mail will not be made Start Stop DOWNLOAD button Live View 8 Recording nera 5 Pl
68. epending on the displayed in this area models of connected cameras and the image Notes format of pictures delivered by the cameras Live camera pictures will not be displayed even e The Live Mode panel will be displayed only when an available button is clicked in the following when a camera picture is displayed in the single cases screen The Live Mode panel is not operable e When the network camera server stops delivering when the quad screen is displayed camera pictures temporarily The network camera server stops delivering camera pictures during Camera Sleep Schedule Refer to page 51 for fur ther information about Camera Sleep Schedule 14 Operation Camera Selection Menu Use this menu to monitor live camera pictures Depending on the setting of the network camera server up to 4 live camera pictures can be monitored simultaneously How to display the camera selection menu Camera Time amp Date Y Select Search Event Search CameraSelect 2L gt c 1 2 3 4 m 5 Camera Number a Quad Screen Copyright 2003 Matsushita Electric Industrial Co Ltd All rights reserved Click the Camera Select tab MODE button You can display a list of up to four Camera Select buttons vertically by clicking the MODE button Clicking the MODE button again will display the Camera Select buttons in the original form Camera Select 1 64 buttons Live View amp Recording
69. er information about the setting menu Delete button Click the Delete button to delete the selected reg istered camera from the Camera List menu When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to complete Click the Cancel button to cancel the deletion Save button Click this button to save the edited settings When this button is clicked the network camera server updates the settings Note If any other menu is displayed without click ing this button after editing the settings in the network camera server will not be updated Click the Cancel button to cancel to update settings Previous link text When the Camera List menu has two or more pages because many cameras are registered and the currently displayed page is not the first page this link text will be displayed Click this link text to display the previous page Next link text When the Camera List menu has two or more pages because many cameras are registered and the currently displayed page is not the last page this link text will be displayed Click this link text to display the next page 49 Camera Properties Click the desired Camera No in the Camera List menu The Camera Properties menu of the selected camera will be displayed Note It is impossible to change the settings during recording Cama Sotileg AA Scheduled Camera Properties
70. es Frames are played in 0 2 seconds intervals Note Depending on the network environment it may take a longer time to play Back Skip only for MPEG 4 Click this button to go back around 3 seconds and pause the playback Live Mode Click this tab to switch from the play mode to the live mode manually Note When pictures are recorded in the MPEG 4 for mat the dialog window below may be displayed Microsoft Internet Explorer l x AN Loading MPEG 4 decoder Failed Check the installation This window will be displayed if the MPEG 4 Plug in Software is not installed to browse MPEG 4 motion pictures on the web browser Refer to the MPEG 4 Plug in Software Installation on page 30 29 Quad Screen When the Quad Screen button is clicked the quad screen pictures from four cameras is displayed in the picture display area When the quad screen is displayed in the picture display area neither manual recording nor operating the camera are available since the camera control frame is not displayed Notes e To display the quad screen an administrator should set the Quad Screen Button of Monitor Screen Setting on the System Properties menu to ON Refer to page 74 for further information about the System Properties menu e When the quad screen is displayed the network camera server regards it as if four users are currently accessing it because four cameras are accessed simultaneously la bee 7A eE LL a i
71. ese operating instructions procedures are described on the assumption that the http address of server s3 British is entered 2 To browse camera pictures click one of the 1 64 buttons When Live View Only is selected as the system type of the network camera server the 1 128 buttons are available The buttons for the registered cameras will be available Click one of the available buttons to dis play the Camera Page 11 When the authentication dialog window is dis played The authentication dialog window will be displayed when ON is selected for Pre Authentication Mode on the System Properties menu Connect to 192 168 0 110 ax Wi 45 710 Authentication User name Es Password Remember my password conce Enter a user name and a password and click the OK button When authenticated the Camera Page will be dis played About Pre Authentication Mode Users who have been authenticated when the Camera Page is displayed for the first time do not have to be authenticated subsequently However when an authenticated user tries to select or operate a camera that the user is not allowed to access the authentication dialog window will be displayed 12 Operation How to Use the TOP MENU To operate the TOP MENU page refer to the following tee mna Help A aeee Jihminisrratnr a Pape i a a APEC 4 Pugin Miri ra ts Laer ili eo FI ayer ata EE
72. f camera numbers can be performed using a web browser installed on a PC connected to the Internet It is unnecessary to install special software on a PC since the network camera server is fully operable with a web browser FEATURES E System Requirements System requirements for using the network camera server differ depending on the sites as described below Center site Prepare a PC meeting the following requirements to install the WV AS710 on PG Memory LAN card OS CD ROM drive USB port Hard disk Core Component CPU Pentium III 1 4GHz or higher 512 MB of RAM or more 100BASE TX controller or 1000BASE T TX SX controller Installing three controllers is recommended for camera sites for user sites for maintenance Red Hat Linux 8 0 Professional Required to install the WV AS710 Required to install the hardware key using an USB hub is available 2 GB or more except disk space for recorded pictures Apache HTTP Server 2 0 40 or later When using the function for alarm notification by e mail establishment of a mail system including a mail server is required Camera site The following cameras can be connected to the network camera server Cameras Controllable cameras Maximum camera number User site WV NM100 WV NP472 Ver 1 03E or later WV NS320 WV NS324 or cameras that can be connected to the network interface unit WJ NT104 WV NM100 WV NS320 WV NS324 or cameras controllable by WJ NT104 Li
73. h tab Note The authentication dialog window will be displayed when a user tries to access a camera which the user is not allowed to access In this case cancel the operation or enter a valid user name and password to be allowed to access and operate the selected camera PC Software Package WV AS710 Camera Time amp Date i Select Search Event Search Enter criteria to search for events Maximum of 10 closest matches will be listed Camera Number 5 Day 31 y Month 3 Year 12003 Hour 21 Minute 46 y or before M Contact Alarm M VMD Alarm M Manual Recording M Image Acquisition Loss V Include Non Video Event Y Show Thumbnail SEARCH Camera Number Enter the desired camera number whose pictures are to be searched in this input box When it is required to enter two or more camera numbers insert a comma between the camera numbers When the pictures of all cameras are to be searched enter an asterisk Note When a camera number without disk space allocation for recorded pictures or a camera number that the user is not allowed to access is entered an error message will be displayed Month Day Select the month and day to be searched Year Enter the year to be searched in this input box with 4 digits An error message will be displayed if the SEARCH button is clicked when this input box is blank Hour Minute Select the hour and minute to be search
74. he selected cam era will be displayed When recording is in process deletion is impossible Middle Part The name and size of the disk space allocated for the selected camera will be displayed Bottom Part The total size of the disk space allocated for the selected camera will be displayed Delete button Click this button to delete the allocated disk space for the selected camera from the disk space for recorded pictures When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to com plete Recording Status List link text Click this link text to return to the Recording Status List menu Disk Space Setting for Camera link text Click this link text to return to the Disk Space set ting for Camera menu 99 Clear Protected Disk Space for Camera Click the desired Camera No of the camera to which the disk space has already been allocated in the Recording Status List menu The Recording Status for Camera menu will be displayed is the selected camera number Click the Clear Protected Disk Space link text to display the Clear Protected Disk Space for Camera When pro tected disk space is cleared available disk space will be increased This menu is available only when Protect is selected for Data Protection Mode on the Recording Schedule Properties menu or on the Alarm Recording menu When there is no protected disk space Curr
75. hile the net work camera server is running the latest regis tered schedule will be applied e When a schedule is registered just after the net work camera server has started up the sched ule with the higher schedule number will be applied Comments Comments about schedules will be displayed 02 Administration Recording Schedule Properties Click the desired No on the Recording Schedule List menu to display the Recording Schedule Properties menu Perform the settings for the selected recording schedule or delete the selected recording schedule Schedule well no be alectra unless you cick the Save button Delete Schedule Schedule No The schedule number is indicated Active Inactive Active Select this to activate the selected sched ule Inactive Select this to inactivate the selected schedule From Select the day hour and minute increments of 5 minutes from the pull down menu for the start time of the selected schedule Day Monday Tuesday Wednesday Thursday Friday Saturday Sunday Mon to Fri Sat and Sun Daily Hour 0 23 Every Minute 0 5 10 15 20 25 30 35 40 45 50 55 min Every Note To activate Recording Schedule for 24 hours select Daily for Day Every for Hour and Every for Minute To Select the day hour and minute increments of 5 minutes from the pull down menu for the end time of the selected schedule Day Monday Tuesday Wednesd
76. ioning of cameras etc mi Even if MPEG 4 Plug in Software is not installed on a PC the network camera server will deliver MPEG 4 camera pictures In this case this prob lem will be solved by downloading MPEG 4 Plug in Software from the TOP MENU page and installing it Refer to page 30 for further information Live Mode Play Mode panel Live Mode Play Mode panel Live Mode panel Operate the selected camera with this panel in the Camera Select tab following case Depending on cameras some of Click this tab to display the Camera Select menu their functions are not available with this panel Time amp Date Search tab e Recording camera pictures Click this tab to display the Time amp Date Search e Preset function menu Use this menu to search recorded pictures e Panning tilting Zooming and scanning stored in the network camera server by time and e Adjustment of focus and brightness date Event Search tab Play Mode panel Click this tab to display the Event Search menu When Live View amp Recording is selected as the Use this menu to search recorded pictures stored system type of the network camera server this in the network camera server by detailed condi panel is available Users can operate this panel to tions play recorded pictures stored in the network cam era server in various ways Picture Display Area Notes The selected camera picture or playback picture is The available functions differ d
77. isk space of the network camera server e Manually recorded camera pictures by clicking the O button of Manual Recording on the Live Mode panel e Automatically recorded camera pictures when an alarm occurred at a camera site Set by an administrator e Automatically recorded camera pictures by the setting of the recording schedule Set by an administrator Play recorded pictures stored in the network camera server as follows 1 Click the Time amp Date Search tab or the Event Search tab Time 8 Date Search Search recorded pictures saved in the network camera server by designating a camera number time and date When playback of the recorded picture finishes a picture that says STOP NO PICTURE will be dis played When starting playback without selecting a link text or a thumbnail from the result list of the Event Search or Time amp Date Search the last frame of the latest recorded picture is played and then the picture that says STOP NO PICTURE will be dis played Event Search Search recorded pictures saved in the network camera server by designating more detailed condi tions than in Time amp Date Search 2 Enter the conditions for searching recorded ST O pictures and then click the SEARCH button The search result will be displayed in the main con trol frame A al l To return to the Time amp Date Search or the N O PICTU RE Event Search from the results click the It returns to a
78. isplayed when delivery of the camera pictures is stopped by the Camera Sleep Schedule of priority 2 blue3 jpg blue3 mg4 Priority 3 This server is currently unavailable Please try later This message will be displayed when delivery of the camera pictures is stopped by the Camera Sleep Schedule of priority 3 blue4 jpg blue4 mg4 Priority 4 Image capture has failed This message will be displayed when deliv ery of the camera pictures is stopped by the Camera Sleep Schedule of priority 4 According to your needs replace the JPEG jpg sample pictures with customized JPEG pictures by naming them with the same name as the sample pictures The size of a customized JPEG picture should be less than 100kbyte and the recommended resolution is 320 x 240 pixels It is impossible to replace the MPEG 4 files mg4 Comments Write comments about the selected schedule Save button Click this button to save the settings of the Camera Sleep Schedule menu When this button is clicked the dia log window for confirmation will be displayed Click the OK button in the dialog window to confirm Delete button Click this button to delete the selected camera sleep schedule When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to confirm Camera Sleep Schedule List link text Click this link text to display the Camera Sleep Schedule List menu Notes e When t
79. l differs depend ing on the transmission speed of cameras Duration None 2 Sec 3 Sec 5 Sec 10 Sec 20 Sec 30 Sec 60 Sec 90 Sec 120 Sec 180 Sec Interval JPEG Mode Only 0 066 Sec 15fps 0 1 Sec 10fps 0 2 Sec 5fps 0 5 Sec 2fps 1 Sec 1fps 2 Sec 3 Sec 5 Sec 10 Sec 30 Sec 60 Sec 120 Sec 180 Sec Note When two or more recordings are performed or depending on the selected values for Interval and Minimum Access Interval Maximum Frame Rate pictures may be recorded at a different recording interval from the set value for Interval Refer to page 63 for further information Recording Select how many seconds after an alarm occurs the network camera server starts recording When recording in the JPEG format alarm pictures will be recorded at the selected interval for Interval JPEG Mode Only When pictures are recorded in the MPEG 4 format recording interval differs depend ing on the transmission speed of cameras Duration 1 image only 2 Sec 3 Sec 5 Sec 10 Sec 20 Sec 30 Sec 60 Sec 90 Sec 120 Sec 180 Sec Interval JPEG Mode Only 0 066 Sec 15fps 0 1 Sec 10fps 0 2 Sec 5fps 0 5 Sec 2fps 1 Sec 1fps 2 Sec 3 Sec 5Sec 10 Sec 30 Sec 60 Sec 120 Sec 180 Sec Note When two or more recordings are performed or depending on the selected values for Interval and Minimum Access Interval Maximum Frame Rate pictures may be record
80. minute increments of 5 minutes from the pull down menu time for the end time of the selected schedule Day Monday Tuesday Wednesday Thursday Friday Saturday Sunday Mon to Fri Sat and Sun Daily Hour 0 23 Every Minute 0 5 10 15 20 25 30 35 40 45 50 55 min Every Note When Daily for Day is selected it is required to select Every for Hour and Every for Minute Camera No Enter the desired camera number to be used for the selected schedule When two cameras or more are used for this schedule insert a comma between the camera numbers When all cameras are used for this schedule enter an asterisk in this input box Priority Select the priority level 1 4 from the pull down menu 1 is the highest priority The picture to be delivered will differ according to the priority When two or more camera sleep schedules overlap the picture with higher priority will be delivered The sample pictures will be installed in the directo ry below when the WV AS710 is installed The details of the sample pictures are listed below usr local s3 bin 93 File name Designed for Message blue1 jpg blue1 mg4 Priority 1 Live streaming video is currently unavailable This message will be displayed when delivery of the camera pictures is stopped by the Camera Sleep Schedule of priority 1 blue2 jpg blue2 mg4 Priority 2 This camera is currently unavailable This message will be d
81. ms is required Confirm the Java Plug in control panel is installed on the PC If it is not installed access the following address to download it The address of the downloading site is sub ject to change http java sun com products plugin For browsing camera pictures with MPEG 4 Plug in Software PC Recommended CPU Memory Monitor Resolution OS Web browser For using MPEG 4 Player PC Recommended CPU Memory Monitor Resolution OS Hard disk PC AT compatible Intel Pentium lll or higher 128 MB of RAM or more True Color 24 bit or more XGA or more 1024 x 768 or more Microsoft Windows 2000 Professional Microsoft Windows 2000 Server Microsoft Windows Millennium Edition Microsoft Windows XP Home Edition Microsoft Windows XP Professional Microsoft Internet Explorer 5 5 SP2 Microsoft Internet Explorer 6 0 SP1 PC AT compatible Intel Pentium lll or higher 128 MB of RAM or more True Color 24 bit or more XGA or more 1024 x 768 or more Microsoft Windows 2000 Professional Microsoft Windows 2000 Server Microsoft Windows Millennium Edition Microsoft Windows XP Home Edition Microsoft Windows XP Professional 10 MB or more to install MPEG 4 Player About Network Environment Depending on the traffic on the network or the security system of the LAN e g firewall it may be difficult to display HTML documents delivered from the network camera server correctly
82. n the search results is clicked or when the Play Mode tab is clicked Note The authentication dialog window will be dis played when a user tries to access a camera which the user is not allowed to access In this case can cel the operation or enter a valid user name and password to be allowed to access and operate the selected camera Play Mode Panel JPEG keai i P Play All Pause Next Frame id Frames Fast Reverse Slow Reverse Fla Play Rewer Play Play To Latest Click this button to go to the latest picture of all recorded pictures in the network camera server To Oldest Click this button to go to the oldest picture of all recorded pictures in the network camera server Fast Reverse Play only for JPEG Click this button to play recorded pictures in reverse at high speed Slow Reverse Play only for JPEG Click this button to play recorded pictures in reverse at slow speed Reverse Play only for JPEG Click this button to play recorded pictures in reverse at the same speed rate as the recording speed rate For example if the recording time is 30 seconds also the Reverse Play time is 30 sec onds Note Depending on the network environment drop frame may occur Therefore it may be impossible to play all frames Play Click this button to play recorded pictures at the same speed rate as the recording speed rate For example if the recording time is 30 seconds also the Play time is 30 seconds
83. ndows NT are registered trademarks of Microsoft Corporation in the U S and other countries Netscape Netscape Navigator Netscape ONE the Netscape N and Ship s Wheel logos are registered trade marks of Netscape Communications Corporation in the U S and other countries Other Netscape product names used in this document are also trademarks of Netscape Communications Corporation and may be registered out side the U S Intel and Pentium are trademarks of Intel Corporation IBM and xSeries are registered trademarks of IBM Corporation in the U S and or other countries Other names of companies and products contained in these operating instructions may be trademarks or regis tered trademarks of their respective owners Distributing copying disassembling reverse compiling reverse engineering and also exporting in violation of export laws of the Software provided with this product is expressly prohibited E Structure of These Operating Instructions These operating instructions consist of an Operation section for general users and Installation and Administration sections for administrators of the network camera server These operating instructions are written on the assumption that users and administrators use Internet Explorer 6 0 SP1 to operate the network camera serv er If other browsers are used the illustrations in these operating instructions may look differently Operation This section describes how to access and operate th
84. ng to the group only can view live pictures and preset operations The other users cannot operate this camera at all Note Basically recording pictures can be done only by administrators When By Camera Group Setting is selected the Operator type users also can record pictures Minimum Access Interval Maximum Frame Rate Select an interval time for accessing the selected camera to capture pictures The default setting is 1 Sec 1fps 0 066 Sec 15fps 0 1 Sec 10fps 0 2 Sec 5fps 0 5 Sec 2fps 1 Sec 1fps 2 Sec 3 Sec 5 Sec 10 Sec 30 Sec 60 Sec 120 Sec 180 Sec Note Depending on the traffic on the network it may be difficult to browse camera pictures When the following occur frequently adjust the interval time for capturing camera picture e When it is difficult to acquire camera pictures because the transmission speed is slow or the traffic on the network is too heavy to receive camera pictures e When around 5 seconds pass after accessing the network camera server and the picture that says Image capture has failed is displayed e When many cameras are set at short interval times it may cause heavy network traffic It may cause not only incorrect access interval but also critical network problems Access User Name In cases where user authentication is required to access the camera or the network interface unit enter the user name registered for the camera or the network interfac
85. nowledge of Apache HTTP Server will be required to access the network camera server from a network Note Installation of the WV AS710 on the Red Hat Linux server allocation of disk space for recorded pictures and uninstallation of the WV AS710 must be performed by a root user Procedures to Establish the Network Camera Server To use the network camera server perform the following 1 Selection of the system type of the network camera server 2 Confirmation of the directory structure 3 Installation of Red Hat Linux 4 Allocation of disk space for recorded pictures when Live View amp Recording is selected 5 Installation of the WV AS710 Execution of the installation script 6 Startup of the WV AS710 7 System environment setting Before running the network camera server access the Administrator s Page and set the system environment Refer to the Administration section on page 43 8 Running of the network camera server After setting the system environment restart the WV AS710 The settings will be validated and the network cam era server will start running 33 selection of the System Type Depending on the system type the network camera server works in different ways System Type Description Live View amp Recording Delivery of live camera pictures and recording can be performed Allocation of disk space for recorded pictures is required on the server Recorded pictures can be searched for and played when de
86. o administrates the network camera server Enter the password of more than 5 characters to administrate the network camera server and press the return key Entering the password will be required twice When the entered passwords do not match execution of the installation script will be interrupted When interrupt ed begin this procedure from step 1 again Decide whether or not to start up the WV AS710 automatically when the server on which Red Hat Linux is installed starts up To start up automatically enter y When y is entered the automatic startup script will be added to etc rc d rc local To not start up automatically enter n In this case start up the WV AS710 manually Confirm the entered parameters When entering the parameters has been completed a confirmation message will be displayed To install after confirming the displayed parameters enter y To change the displayed parameters enter n When n is entered execution of the installation script will be interrupted In this case begin this procedure from step 1 again 39 6 Create disk space for recorded pictures When disk space for recorded pictures is not prepared in advance a message asking whether to create or not disk space for recorded pictures on an existing partition will be displayed When Live View amp Recording will be selected as the system type and it will be required to create disk space for recorded pictures enter y When it
87. ocated Disk Space The size of the disk space allocated for the select ed camera will be displayed Available Disk Space The available disk space possible to allocate to the selected camera will be displayed Bottom Part Space To Be Added percentage of the available disk space which can be used Enter the desired percentage of the available disk space to allocate to the selected camera When another input box is clicked after entering percent age number the entered percentage will be con verted into megabytes and the converted value will be displayed in the input box Space To Be Added MB automatically The total size allocated for the selected camera will also be recalculated and dis played in the Total automatically Space To Be Added MB Enter the desired size MB of the available disk space to allocate for the selected camera When another input box is clicked after entering the amount of disk space the entered size MB will be converted into a percentage and the converted value will be displayed in the input box Space To Be Added automatically The total size allocat ed for the selected camera will also be recalculated and displayed in the Total automatically Note lt is impossible to enter a number bigger than the Available Disk Space Total Enter the desired total size MB of the disk space to allocate for the selected camera When another input box is clicked after entering
88. of a mail server system is required Refer to the operating instructions of the mail server software for further information Environment Settings of the Network Camera Server Refer to the Administration section on page 43 for further information about the environment settings Stop the WV AS710 To stop the WV AS710 click the Stop button on the Stop and Restart menu Refer to page 79 for further informa tion Setting Menu Stop and Restart jan Type When the system is deleting a disk space including a camera entry pnl shop after he process is completed Shop WW AS 10 Sp Rasta Ana 7 10 Fasani 42 Installation Uninstallation When uninstallation of the WV AS710 is needed execute the script for uninstallation When the script for uninstallation is executed all directories created when the WV AS710 was installed will be delet ed except the newly created partitions or directories for disk space named S3_ DATAxx their contents will be deleted Note The uninstallation of the WV AS710 must be performed by a root user The script for uninstallation was installed in the following directory when the WV AS710 was installed lusr local s3 bin uninstall To uninstall the WV AS710 enter the following commands cd usr local s3 bin uninstall H s3uninst Administration To run the network camera server it is required to access the Administrator s Page to perform the settings Refer to this chapter
89. on how to access the Administrator s Page and the settings required to be set How to Display the Administrator s Page 1 Start up the web browser and display the TOP Password Enter the password corresponding to 43 MENU of the network camera server http server address s3 British The server address differs depending on the user environment 2 Click the Administrator s Page button The authentication dialog window will be displayed Connect to 1927 163 0 110 W w 45710 Authentication User name a Password Remember my password cancel The Administrator s Page can be displayed by entering the following address In this case the authentication dialog window will also be displayed http server address s3 British cfg Note To perform the settings of the network cam era server use Internet Explorer 5 5 SP2 or 6 0 SP 1 If other browsers are used the settings cannot be performed correctly Enter a user name and a password and then click the OK button User name Enter the user name belonging to the admin group the entered user name Just after installation only the user name admin is registered in the admin group The password for the user name admin is the password entered when installing the WV AS710 When the user is authenticated the Administrator s Page will be displayed Select System Type Sawar Vernoe WO S57 200309174 Click the desi
90. on the user type Users belonging to these groups cannot access the Administrator s Page Note The names of groups can be changed on the Group Name menu User Type Select a user type for the user from Operator or Monitor Refer to the Authentication on page 66 for information about what users can do when accessing cameras When a user belongs to the admin group settings for the User Type will be ignored Register button Click this button to add a new user with the entered profile When this button is clicked the dialog win dow for confirmation will be displayed Click the OK button in the dialog window to confirm User List link text Click this link text to return to the User List menu 2 Change User Profile Click the User Name on the User List menu to display the Change User Profile menu On this page change the password belonging group and the user type of the selected user hs Dariare i rd pl wich Mi ture hl 1 Jl A he Le Change User Profile a _ _ UserName O i ce i Contra Passi eee Seats Lier Profle wall not b changed unless you chch the Sane button Delete User Delete User Name The selected user name will be displayed It is impossible to change the user name Password Enter a new password up to 32 alphanumeric char acters when a new password is needed The entered password will not be displayed for security Confirm Password Enter the same new
91. orms Performs more detailed settings the basic settings of the camera than the Camera List menu properties Camera Sleep Schedule Camera Sleep Schedule List Properties Displays the list for the camera Performs the settings for the sleep schedule camera sleep schedule Recording Recording Status List Disk Space Allocation for Displays the recording status Camera Allocates disk space Disk Space Setting for Disk Space Addition Camera Adds disk space Selects the menu to perform the settings for disk space Delete Disk Space Deletes disk space Clear Protected Disk Space Clears protected disk space Disk Space Allocation Allocates the same amount of disk space simultaneously to the cameras which no disk space has been allocated yet Recording Schedule List Recording Schedule Properties Displays the list for the recording Performs the settings for the recording schedule schedule Alarm Recording Performs the recording parame ter settings when an alarm occurs User Camera User List User Registration Group Displays the Registered users Adds users and their belonging groups Change User Profile Changes passwords or belonging group of registered users Camera Grouping Assigns users to groups 46 Administration Setting Menu Tab Setting Page User Camera Group Name Group Changes group names System Properties Performs the basic settings of the network camera server
92. ot recognize a directory if its name is not S3_ DATAxx 2 Set a symbolic link for the created directory to be recognized as S3_DATAxx Example If the S3_ DATA02 directory is created in the mnt2 partition enter the following to set a symbolic link for the S3_DATA02 directory mkdir mnt2 S3_ DATA02 Fin s mnt2 S3_DATAO 2 38 Installation Installation of the WV AS710 To install the WV AS710 do the followings Mounting the CD ROM Insert the CD ROM that includes the WV AS710 into the CD ROM drive Enter the following commands to mount the CD ROM and change the current directory to the CD ROM mount mnt cdrom Hcd mnt cdrom Execution of the Installation Script Installation by Unpacking the Archive Files Unpack the archive files in the mounted CD ROM and install the files 1 Start up the installation script in the mounted CD ROM s3inst 2 Enter the environment parameter When the installation script is executed the WV AS710 requests the environment parameters required for start up To install not in the default path of Red Hat Linux enter a desired path and press the return key To install in the default path of Red Hat Linux displayed path between do not enter any path and press the return key Enter American or British for the Standard Language Enter a password for an administrator admin The entered string of characters will be a password for an administrator wh
93. pid file exists in the var run directory or not If it exists delete it Is the WV AS710 started up Are the power of the network interface unit and the cameras on Are the IP addresses entered in the Camera Properties menu cor rect Depending on the traffic on the network it may happen that automatic reload of pictures from a web browser may stop In this case click the reload button of the web browser Is the monitor resolution set to True Color 24 bit or more Are the settings of the network interface unit correct When the net work camera server and the network interface unit are used in the same system do not set the network interface unit to Random Input Selection Mode Refer to the operating instructions of the network interface unit for further information Are Block All Cookies or Invalid selected or not selected in the set tings of the web browser In both cases select Accept All Cookies lt is possible that another user is operating the camera Try to operate it later lt is possible that the camera has an operating restriction Refer to an administrator about your user type When operating WV NM100 WV NS320 or WV NS324 enter Access User Name and Access User Password registered in the setting menu of the cameras Is the camera connected Is the same IP address entered in the IP Address on the Camera Properties menu and on the setting menu of the camera site 01 Troubles Symptoms
94. play the Change User Profile menu of the selected user and do it on that menu Group Name The group to which user belongs will be displayed 70 Administration User Registration Click the User Registration button on the User List menu to display the User Registration menu On this page register a new user Leer 15 se User Name Enter an unregistered user name for a new user of up to 32 alphanumeric characters Note The registered user name cannot be changed When registered mistakenly delete the user name and register it again Display the User Registration menu to delete a user name Password Enter a password for a new user name up to 32 alphanumeric characters Confirm Password Enter the same password entered in the Password input box above for confirmation Group Select a group this user should belong to The Group1 20 and admin are registered as default groups Admin Users who administrate the network camera server administrators are required to belong to this group All users belonging to the admin group can operate all cameras record search play recorded pictures preset operation and administrate the network camera server by accessing the Administrator s Page Group 1 20 These groups are for general users to access the network camera server to browse live cam era pictures or operate cameras What users can do while accessing cameras differs depending
95. red button in the Setting Menu Some types of Setting Menu have two or more tabs Click the desired tab to display the menu to be set Click the Save or Save button on each menu page to save the changed settings A dialog window for confirmation will be displayed Follow the displayed instructions to complete the settings System Type Live View Recording Save Administration 6 To stop or restart the WV AS710 display the Stop and Restart menu System button Stop and Restart tab Stop and Restart When the eyater is deleting a disk spacebrciuding e camera entry iteal Stop after the process 5 completed Stop iW ASTID Stop Fiesta Wi AST EO 7 Click the Restart button to restart or the Stop button to stop the WV AS710 A dialog window for confirmation will be displayed 44 When the Restart button is clicked Microsoft Internet Explorer X es Are you sure you want to stop Wy 45710 and restart it Cancel When the Stop button is clicked Microsoft Internet Explorer x YD Are you sure you want Eo stop Ww 45710 7 i Cancel Click one of the following buttons in the dialog win dow OK To stop or restart the WV AS710 Cancel To go back to the Stop and Restart menu List of Settings Setting Menu Tab Setting Page System Type System Type Selects the system type Camera Camera List Camera Properties Displays the list and perf
96. rre col OET n TITLE When the quad screen is displayed each picture is displayed with its respective title above Click the desired camera title to display the desired camera picture in the single screen PREV NEXT buttons When the quad screen is displayed the PREV button and the NEXT button appear below the quad screen When the PREV button is clicked the previous four camera pictures will be displayed When the NEXT button is clicked the next four camera pictures will be displayed Note If there is no connected camera for the selected number a blue picture or an icon indicating a miss ing picture will be displayed 30 Operation Installation of the MPEG 4 Plug in Software To view live pictures or play recorded pictures in the MPEG 4 format it is required to install the MPEG 4 Plug in Software on the PC Notes e Confirm your PC fulfills the system requirements before installing the MPEG 4 Plug in Software Refer to page 7 for further information e The MPEG 4 Plug in Software is not compatible with Windows NT e Install or uninstall the MPEG 4 Plug in Software after logging on to the PC as an administrator Administrator Windows 2000 Computer Administrator Windows XP How to Install To install the MPEG 4 Plug in Software do the following 1 Display the TOP MENU of the network camera server http server address s3 British The server address differs depending on the user environment 2 Click the
97. rval is not proper the camera pictures will not be displayed correctly Maximum Concurrent QVGA VGA Access 150 Live View Only Very Slow Not Recommended 200 Live View Only Very Slow Not Recommended This setting will be ignored when cameras delivering MPEG 4 pictures since they deliver pictures according to the settings of camera 76 Administration Auto Erase Setting Image Auto Erase Select a period to keep recorded pictures in the disk space for recorded pictures 7 Days 15 Days 30 Days 60 Days 90 Days 180 Days No limitation When the selected period has passed the stored recorded pictures will be deleted Event Log Auto Erase Select a period to keep event information recorded in a database 7 Days 15 Days 30 Days 60 Days 90 Days 180 Days No limitation When the selected period has passed the event infor mation will be deleted automatically It is impossible to search events in the deleted event information using Event Search Save button Click this button to save the settings of the System Properties menu When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to con firm Note If any other menu is displayed without click ing this button after editing the settings in the network camera server will not be updated 2 Alarm Notification Click the System button of the Setting Menu to display the System Proper
98. s Delete button Click this button to delete the selected recording schedule When this button is clicked the dialog window for confirmation will be displayed Click the OK button in the dialog window to confirm Recording Schedule List link text Click this link text to display the Recording Schedule List menu About Interval e Relation to Priority and Data Protection Mode When two or more recordings are performed in the same period of time Interval will change during recording depending on the following circum stances 63 When Data Protection Mode is different Regardless of the setting for Priority recording will be performed at the recording interval of the recording whose Data Protection Mode is Protect For example when a manual recording priority 4 recorded pictures are stored in the pro tected disk space is performed during a schedule recording whose priority is set to 2 and also Overwrite is selected for Data Protection Mode pictures will be recorded at the recording interval of the manual recording When Data Protection Mode is the same Recording will be performed at the recording inter val of the recording whose Priority is the highest When Priority and Data Protection Mode are the same Recording will be performed at the recording inter val of the recording started later Relation to Minimum Access Interval Maximum Frame Rate Basically the net
99. s 640 x 240 pixels some image editing software such as Paint will display the picture in the half vertical size 2 Display the index html using a web browser The web page below will be displayed _ ES AE A en EE AEE NOS ME LM i n my i SS z mp ve Zs 0 A SKIP Select a number of thumbnail display pages to be skipped TOP Click this button to go back to the top page on the left frame PREV Click this button to display the previous page The displayed page depends on the selected page number for SKIP NEXT Click this button to display the next page The displayed page depends on the selected page number for SKIP LAST Click this button to go to the last page Frame No Click this button to display the currently browsed frame number SPEED Click this button to display the playback speed When playing in reverse the playback speed will be displayed with a minus STEP lt lt Click this button to go back to a previous frame and pause PLAY Click this button to start playback STEP gt gt Click this button to go to the next frame and pause SPEED Click this button to slow down the playback speed one step 1 PAUSE Click this button to pause the playback SPEED Click this button to speed up the playback speed one step 1 Operation To play MPEG 4 3 Select File Open from the menu bar and To play the downloaded recorded picture in the then select an uncompresse
100. s on the menus of Recording 3 Setting cameras for recording on the menus of Recording 36 3 How to Allocate Disk Space There are two following ways to allocate disk space e Use a whole partition as disk space for recorded pictures e Use a directory as disk space for recorded pictures Creating a New Partition to Use as Disk Space for Recorded Pictures When preparing a new hard disk or creating a new partition on a currently used hard disk the new partition must be the following name to mount It is possible to create this partition when installing Red Hat Linux S3_DATAxx xx two digits number e g S3_DATADOO S3_ DATA01 etc Notes e When a new hard disk is prepared exclusively for recorded pictures do not create any other partition than S3_DATAxx e Do not install any other software in the 53_DATAxx partition e Select ext2 for the file system If ext3 or other file systems are selected the performance of the network cam era server may deteriorate e The network camera server will not recognize a partition if its name is not S3_ DATAxx Using an Existing Partition as Disk Space for Recorded Pictures It is possible to create a new directory on an existing partition to use as disk space for recorded pictures In this case proceed as follows 1 Create a directory in the existing partition and name the new directory S3_DATAxx with the mkdir command Note The network camera server will n
101. sired and they can be downloaded on a user s PC hard disk Live View Only Only delivery of live camera pictures is available with this system type Recording playback searching and the alarm function are not available with this system type Note The system type can be changed anytime if required In case of switching from the Live View Only to the Live View amp Recording allocation of disk space for recorded pictures will be required Design a system fulfilling all of the conditions below to run the network camera server in each system type fs ive View Recording Live View Only Camera Site Maximum camera number Maximum total bit rate Maximum total frame rate User Site Maximum concurrent access Live Maximum total bit rate Maximum total frame rate User Site Maximum concurrent access Playback Maximum total bit rate Maximum total frame rate User Site Maximum concurrent access Live 8 Playback Maximum total bit rate Maximum total frame rate 1 To connect 128 cameras it is required to set the maximum bit rate at less than 230kbps and the maximum frame rate at less than 1 5fps per a camera in the camera settings Refer to the following values for the maximum frame rate of cameras The following values may differ depending on objects to be captured and the network environment Also depending on the traffic on the network acquiring pictures at the maximum frame rate may fail Size of a JPEG QVGA Approx 15 22 KB
102. sk Space Addition for Camera is the selected camera number Delete Disk Space link text Click this link text to display the Delete Disk Space for Camera is the selected camera number Clear Protected Disk Space link text Click this link text to display the Clear Protected Disk Space for Camera menu is the selected camera number Recording Status List link text Click this link text to return to the Recording Status List menu 9 Disk Space Addition for Camera Click the desired Camera No of the camera to which the disk space has already been allocated in the Recording Status List menu The Disk Space Setting for Camera menu will be displayed is the selected camera num ber Click the Disk Space Addition link text to display the Disk Space Addition for Camera is the selected camera number Adding disk space for the selected camera to increase recording time is possible on this page Disk Sence Aalecatonl Racertisa Schetala Alem Racari na Disk Space Addition for Camerat Allocated Space 1 53 aT aot 100 ME A bocassd Disk Space 100 ME fallido Disk Space 6004 HE Space To Be Added parentage of the aralable dsk space which can ba usadi Space To Be Added ME Upper Part S3 DATAxx The name of the disk space and the allocated size for the selected camera will be displayed is the number of disk space xx is a two digits number Middle Part All
103. ted To allocate disk space for recorded pictures refer to the following About Disk Space for Recorded Pictures When the network camera server runs on the Live View amp Recording system it is required to allocate disk space for recorded pictures The following functions will be available by allocating disk space for recorded pictures e Schedule recording e Alarm recording e Manual recording Note When the network camera server runs on a Live View Only system allocating disk space for recorded pic tures is not necessary Cautions When Allocating Disk Space Depending on the place the disk space for recorded pictures has been allocated the performance of the network camera server may deteriorate To prevent deterioration of the performance refer to the following e It is recommended to prepare a hard disk exclusively for recorded pictures and to create a new partition as the disk space for recorded pictures e If data which is not recorded pictures is stored in the partition created as disk space for recorded pictures the performance of the network camera server may deteriorate e After allocating disk space for recorded pictures allocate disk space for recorded pictures of each camera in the Administrator s Page root ve S3_DATA0OO Recording by the cameras set on the menus of Recording Creating disk space for recorded pictures on the server E 2 Allocating disk space for recorded picture
104. the number for total size the entered total size MB will be con verted into a percentage and the converted value will be displayed in the input box Space To Be Added and Space To Be Added MB auto matically Note lt is impossible to enter a number bigger than the Available Disk Space Add button Click this button to add disk space for the selected camera When this button is clicked the disk space will be added and the total size of disk space will be the same size as displayed in the Total input box Recording Status List link text Click this link text to return to the Recording Status List menu Disk Space Setting for Camera link text Click this link text to return to the Disk Space Setting for Camera menu Administration Delete Disk Space for Camera Click the desired Camera No of the camera to which the disk space has already been allocated in the Recording Status List menu The Recording Status for Camera menu will be displayed is the selected camera number Click the Delete Disk Space link text to display the Delete Disk Space for Camera is the selected camera number Disk Senor cada acacia Schetala Alem Aecanting Setting Menu Delete Disk Space for Camera 1 Ho recordings in proce located Space 51 DATADO 16048 Total 100 ae Eecordiog Status List Disk Space Setting for Camera 1 Upper Part The status of the disk space for t
105. ties menu and click the Alarm Notification tab The Alarm Notification menu will be displayed Perform the settings concerning what the network camera server should do when an alarm occurs on this menu SS gs wall not bs elffecins Und ss you cick ihe Seve Dutton E Mail Mode Select when the network camera server should send e mail The network camera server will attach an alarm picture Notes to the e mail by selecting alarm type e When notifying of an alarm occurring by e mail set deli the LAN card eth0 on the PC server to the vering side e In the following cases notifying the correct IP address of the network camera server by e mail may fail When the LAN card eth0 on the PC server is not set to the delivering side When a router is installed between the Internet and the network camera server and network address translation NAT is used In this case open all files whose name starts from template_alarm in usr local s3 template with an editor soft ware and change the i part to make addresses accessible to the Internet e In the following cases it will not be possible to browse pictures even if an address in an e mail IS C licked When Do not notify is selected for E Mail Mode e When an alarm has been transmitted by a camera set to deliver MPEG 4 pictures e It will be impossible to identify which camera is transmitting an alarm signal if a router is inst
106. unctions for each user differ depending on the user type belonging group and the operating restriction as below When Unrestricted is selected for Operating Restriction User Type Browsing live cam Preset operation Operation of a camera Searching and Recording era picture except preset operation playback Administrator oF o o 9 operator OA mor A When View And Preset Only is selected for Operating Restriction User Type Browsing live cam Preset operation Operation of a camera Searching and Recording era picture except preset operation playback Administrator Oo po o o e 96 operar A mor JA When By Camera Group Setting is selected for Operating Restriction and a camera and a user belongs to the same group User Type Browsing live cam Preset operation Operation of a camera Searching and Recording era O E preset operation DC Administrator e TARA Mentor JA When By Camera Group Setting is selected for Operating Restriction and a camera and a user belongs to the different group User Type Browsing live cam Preset operation Operation of a camera Searching and Recording era picture except preset operation playback Administrator ANC O gt Oper LA mor PA 6 Group There are two kinds of group the general user group Group 1 Group 20 and the administrator group admin All users should belong to a group The general user group Group 1 20
107. utton is clicked when this input box is blank Hour Minute Select the hour and minute to be searched Show Thumbnail Check this box to display a list of results with the respective pictures in small scale The MPEG 4 recorded pictures will not be displayed with the thumbnail in the list of results SEARCH button Click this button to start searching A list of pictures recorded near the entered time and date will be displayed as results Result List Text Result List Thumbnail Camera 5 31 03 2003 19 44 56 rh amp da Camera 5 31 03 2003 19 44 56 24 Operation Click the desired result The selected recorded pic ture will be played from the point of time and date entered for search Notes e When the time on the clocks of the network camera server and the PC do not match searches will not be performed correctly e When pictures are recorded in the MPEG 4 for mat the dialog window below may be dis played Microsoft Internet Explorer f X AN Loading MPEG 4 decoder Failed Check the installation This window will be displayed if the MPEG 4 Plug in Software is not installed to browse MPEG 4 motion pictures on the web browser Refer to the MPEG 4 Plug in Software Installation on page 30 Event Search Search recorded pictures saved in the network camera server by more detailed criteria than in Time amp Date Search How to display the Event Search Click the Event Searc
108. ve View amp Recording 64 cameras Live View Only 128 cameras Recommended environment to access the network camera server is as below For browsing JPEG PC Recommended CPU Memory OS Web browser PC AT compatible Intel Pentium lll or higher 128MB of RAM or more Microsoft Windows 98 Second Edition Microsoft Windows NT 4 0 SP6a Microsoft Windows Millennium Edition Microsoft Windows 2000 Professional Microsoft Windows 2000 Server Microsoft Windows XP Home Edition Microsoft Windows XP Professional Microsoft Internet Explorer 5 5 SP2 Microsoft Internet Explorer 6 0 SP1 Netscape Navigator 4 78 Notes e It is required to configure a web browser to accept cookies from the network camera server If the web browser is configured to Block All Cookies set it to Accept All Cookies If it is configured to prompt you when a cookie is sent click the Allow button in the displayed dialog window e Netscape Navigator can be used only on Microsoft Windows XP and or Microsoft Windows 2000 When Netscape Navigator is used the recorded time and date will not be displayed during playback of recorded pic tures stored on the network camera server e When Internet Explorer 5 5 SP2 or 6 0 SP1 is used with either Microsoft Windows NT 4 0 SP6a Microsoft Windows XP Home Edition and Microsoft Windows XP Professional Java 2 Runtime Environment Standard Edition 1 4 1 of Sun Microsyste
109. wn the web browser e When another user accessing the camera while it is recording clicks the 0 button e When an administrator stops or restarts the WV AS710 Recording will not resume automatically after restart Zoom Click the WIDE button or the TELE button to control the zoom lens of the selected camera Note Even if the WIDE button or the TELE button is kept pressed the camera will not keep on zooming Preset Select a preset position to move the camera to the selected preset position Preset position numbers 1 to 64 and home position are available for this function The available preset position numbers differ depending on the model of the selected camera as below A camera connected by the WJ NT104 1 to 64 WV NM100 1 to 8 WV NS320 WV NS324 1 to 16 Note The preset function is a function of the camera not of the network camera server If the preset position is not set on the camera this function is not available Pan Tilt Click this button to move the camera horizontally or vertically Each click moves the camera horizontally or vertically by one step The speed of panning and tilting and the range of a step differ depending on the model of the selected camera When the selected camera is delivering JPEG When one of the edges top bottom left right of the camera picture is clicked the camera pans or tilts toward the clicked direction When browsing MPEG 4 panning and tilting by clicking on the
110. wo or more schedules are in succession the accuracy of sequential recording of the schedules may not be guaranteed Live pictures may be delivered temporarily between the schedules e When a camera sleep schedule is changed live pictures may be delivered temporarily until the changed sched ule is validated 94 Administration Recording Status List Click the Recording button of the Setting Menu or click the Recording Status tab The Recording Status List menu will be displayed It is useful to check the status of disk space for each camera with this page Ascarding Statue ink Sa ace Mlacatian Hacarding Scien 192168012 1CH Geet Setting Menu Recording Status List 1OZ16BDA1 10H Gate a taates0ts 204 Gaes 4 lam Recordin 5 Schedule Recording ki ianua Recondina Camera No Click the desired Camera No to perform the set tings for the disk space of the selected camera If the disk space for the selected camera has not yet been allocated The Disk Space Allocation for Camera menu will be displayed is the selected camera num ber If disk space for the selected camera has already been allocated The Disk Space Setting for Camera menu will be displayed is the selected camera number IP Address The IP address of each connected camera is dis played Channel The channel of each camera connected by the net work interface unit is displayed Title The title of
111. work camera server records cam era pictures when acquiring camera pictures Therefore recording will be performed at the selected value for Minimum Access Interval Maximum Frame Rate in the following cases When the selected value for Interval is the same or longer than the selected value for Minimum Access Interval Maximum Frame Rate When the selected value for Interval is an integral multiple value of the selected value for Minimum Access Interval Maximum Frame Rate recording will be performed at the selected Interval However when the selected value for Interval is not an integral multiple value of the selected value for Minimum Access Interval Maximum Frame Rate recording will be performed at the selected Minimum Access Interval Maximum Frame Rate When the selected value for Interval is shorter than the selected value for Minimum Access Interval Maximum Frame Rate In this case recording will be performed at the selected Minimum Access Interval Maximum Frame Rate Administration Alarm Recording Click the Recording button of the Setting Menu to display the Recording Schedule List menu and click the Alarm Recording tab The Alarm Recording menu will be displayed Pre Recording Rete ing Fran ipa Spece Alocaiioe Repening Schades 64 Alarm Recording Settings wil nal be faciva unless you click the Save bitan Recording Select ON or OFF to record camera pictures or

Download Pdf Manuals

Related Search

Related Contents

guia fluence - HTM Eletrônica  取扱説明書  NuMax SBR32 Installation Guide  Guide de l`utilisateur/ Guida dell`utente/Soluzione  RESOLUCION No. 3574 DE 2012  取扱説明書 (本書)  USER MANUAL - Support Sagemcom  

Copyright © All rights reserved. Failed to retrieve file