WF2501 WF2502 User Manual netis150/300MbpsWireless
Contents
1. Hardware Version WF2501 Firmware Version test version Figure 4 1 4 1 2 WAN This feature provides running status information of the WAN port the port connect to the Internet WAN Connection Type DHCP MAC Address QD O0 22 22 44 91 IP Address 192 168 175 101 Subnet Mask 255 255 255 0 Default Gateway 192 168 175 1 Primary DMS 192 168 2 1 Secondary DNS 202 1013 24 55 Link Status Connect EEES Figure 4 2 gt Connection Type Display router s current connection type It should be one of PPPoE DHCP Static IP depending on what kind of connection type your ISP provides gt Physical Address The physical address of WAN port this is a unique address assigned by manufacturer gt IP Address The IP address you obtained after connect to the Internet if you haven t connected to the Internet yet this field is 0 0 0 0 gt Subnet Mask The Subnet mask you obtained after connect to the Internet if you haven t 29 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual connected to Internet yet this field 1s 0 0 0 0 Default Gateway The IP address of Default gateway you obtained after connect to the Internet if you haven t connected to Internet yet this field 1s 0 0 0 0 Primary DNS The DNS server translates domain or website names into IP address input the most common DNS server address you used or provided by your ISP Secondary DNS Input IP add2. If the router ever freezes in a setting change process or if you can t access it because you can t remember the IP you have given it or other problem you may have to utilize the reset button on the back of the router to put it back to factory settings You have to press and hole this button for a few seconds 2 6s with a pencil when it is working then release and it will restore settings to the factory configuration The other way to restore factory settings is through the same user interface used in setup 10 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Click on System management Restore and click on the Restore button 2 4 Hardware Installation Procedures The procedures to install the 150 300Mbps Wireless N Long Distance Broadband Routerpleaserefers to the following picture LANA LANS LANZ LAN WAN WPSDefaut PWR LANS LANZ LANI WAN WPS Defaut PWR rr ao o WF2501 Computer to Ethernet cable Notebook with wireless card WF2502 Figure 2 3 Attach one end of an Ethernet cable to your computer s Ethernet port and the other end to one of the LAN ports of your router Connect another Ethernet cable from your Cable DSL modem to the WAN port of your router gt Connect the single DC output connector of the power adapter to the power jack on the back of the router and plug the Power Adapter into an AC outlet 11 150 300Mbps Wir
3. 1 3 SUpporting Standard and Protocol gt IEEE 802 11b g n 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual IEEE 802 11e IEEE 802 11h IEEE 802 11k IEEE 802 111 IEEE 802 3 10Base T IEEE 802 3u 100Base TX V V V V V WV 1 4 Working Environment Temperature 0 to40 C operating gt 40 to 70 C storage Humidity gt 10 to 90 non condensing operating gt 5 to 90 non condensing storage Power gt DCO9V 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 2 Hardware Installation 2 1 System Requirement Minimum Requirements Broadband DSL Cable modem and service with Ethernet port gt 802 1In b g n wireless adapter or Ethernet adapter and cable for each computer gt Internet Explorer 5 0 Firefox 2 0 or Safari 1 4 or higher 2 2 Panel Front panel WF2501 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual LILILI LILI WF2502 Figure 2 1 SYS WAN Connection normal WAN Connection abnormal O LAN Connection abnormal n LAN Connection normal ff 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Flashing WiFi data transmitting Off WiFi connection abnormal Rear panel FET FFT T To ol WF2501 WF2502 Figure 2 2 Connect to Power adapter please don t use the unknown PWR power adapter otherwise your device may be damaged 2 3 Restore to factory configuration
4. save and reboot the router gt fyour AP is encrypted select wireless security and input the key in this interface then click on save and reboot the router Repeater In this mode it s an electronic device that amplifies a signal before transmitting it again it can be used in computer networks to extend transmitting distances Attach one end of an Ethernet cable to your computer s port and the other end to one of the LAN ports of your router gt Configure Your Computer according to the QIG 99 66 Select wireless wireless settings select the repeater mode input the Repeater SSID then click the AP Scan and you will see a new window options select the AP you want to connect to and click the connect button below 61
5. 300Mbps Wireless N Long Distance Broadband Router through your computer has a WEB browser installed Please follow up the steps listed below 3 3 Login Open a web browser Safari Internet Explorer etc on the computer you have just connected to the router enterhttp 192 168 1 1 and will automatically login our UI A about blank Microsoft Internet Explorer File Edit View Favorites Tools Help a x E A s Search 5 Favorites Address l http 192 168 1 3 Go Links Internet Figure 3 23 After you have logged in the router s user interface will be displayed The left menu shows the main options to configure the system and the right screen is the summary information for viewing and adjusting the configurations 27 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual dILL M ans ial 1 js at a Ve Br Auto v r i a WY CU puit eae ee MEL Authentication Type None kad LAN de dar Pasa a ah Seem ooi La V O Do not set the MAC address as the wirless network card at the WISP mode WAN MAC Address 00 00 40 01 02 09 EE Figure 3 24 28 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 4 Router Setup 4 1 Status This feature provides running status information and detailed information about router 4 1 1 Version Show the hardware version and firmware version
6. 9 Key Renewak B6400 seconds 60 86400 Figure 4 28 4 5 2 5 WPA WPA2 PSK This item mixed WPA PSK and WPA2 PSK mode which provides higher security level you can configure it according with WPA PSK or WPA2 PSK For the security Er your wireless network we strongly recommend you to use the authentication type of WPA2 PSK encryption type of AES or authentication type of WPA2 PSK encryption type of TKIP Authentication Type MUZE T Encryption Type TKIP AES TKIP amp AES Key Mode HEX ASCII Key please enter any 8 63 charcters ASCII charcters A Z a z 0 9 Key Renewal 86400 86400 seconds 60 86400 Figure 4 29 42 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 4 5 3 Wireless MAC Filtering Wireless MAC Address Filtering Wireless Access Control Status Enable 9 Disable Permit wireless connection for MAC address listed others are Denied Wireless Access Control RUB ony wireless connection for MAC address listed others are Permitted Rule Description MAC Address _ Items show in every single page E amp E p o ix Total O Pages ID MAC Address Delete Figure 4 30 MAC Filter Status the default is disable You can filter wired users by enabling this function thus unauthorized users can not access the network Description describe MAC Filter list to tell from different MAC Filter lists gt Rule you can select
7. Local Area Connection Properties window 21 o da 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual a _ ____ o ARA UL A d po p T o od an a LI PS O A eA oen E ote e mg imi ue e ea gta y ole za Lor En cion Hi M EI cmd Lo ri esa ar cbr A LO rk mts a d Networking Connect using ne Intel R PRO 1000 MT Network Connection This connection uses the following tems o Client for Microsoft Networks 21005 Packet Scheduler dal File and Printer Sharing for Microsoft Networks Intemet Protocol Version 6 TCP IPv5 2 Internet Protocol Version 4 TCP IPy4 e Link Layer Topology Discovery Mapper O Driver ink Layer Topology Discovery Responder Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Figure 3 17 3 1 5 Windows 7 Please follow the steps blow to setup your computer Go to Start ControlPanel Network and Internet Click Network and Sharing Center Change adapter settings Highlight the icon Local Area Connection right click your mouse and click Properties Highlight Internet Protocol version 4 TCP IPv4 22 gt 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual FERA ESB O pe fies Oye Control Panel Network and Internet Network Connections ES Search Network Co
8. Pages ID Description Internal Host IP Address Protocol External Port Internal Port Del Figure 4 37 Description Describe current virtual server item Internal Host IP Address The Internal Host IP Address indicates IP address of the internal host using virtual server gt Protocol The protocol item supplies several protocols For example if you have web server within LAN you can select the HTTP template then the router will input port number 80 automatically External Port Input an extranet port number the users in Internet can see these ports Internal Port Input an intranet port number 4 7 20 Port Triggering Port trigger module dynamically registers virtual server rules when any IP host generates the packet from the specified trigger protocol and port Port trigger module use forward protocol type and port number and use the IPaddress of host that generates the trigger packet when it registers a rule 48 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Port Triggering Predefined Trigger Rules Select one of the predefined rules Rule Name Trigger Protocol EM 3 3 Trigger Port be Forward Protocol TCP ENE Forward Port o de e c Total O Pages ID Rule Name Trigger Condition Forward Condition Del Items show in every single page 3 Figure 4 38 Predefined Trigger Rules select one of the P
9. at the start search bar and press the Enter gt For MAC OS Thesystem will complete this operation automatically At the DOS prompt type the following command If the Command window returns something similar to the following C Documents and Settings admin gt ping 192 168 1 1 Pinging 192 168 1 1 with 32 bytes of data Reply from 192 168 1 1 bytes 32 time 1ms TTL 64 Reply from 192 168 1 1 bytes 32 time 1ms TTL 64 Reply from 192 168 1 1 bytes 32 time 1ms TTL 64 Reply from 192 168 1 1 bytes 32 time 1ms TTL 64 Ping statistics for 192 168 1 1 Packets Sent 4 Received 4 Lost 0 0 loss Approximate round trip times in milli seconds Minimum 1ms Maximum 1ms Average 1ms Then the connection between the router and your computer has been successfully established If the computer fails to connect to the router the Command window will return the following C Documents and Settings admin gt ping 192 168 1 1 Pinging 192 168 1 1 with 32 bytes of data 26 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Request timed out Request timed out Request timed out Request timed out Ping statistics for 192 168 1 1 Packets Sent 4 Received 0 Lost 4 100 loss Verify your computer s network settings are correct and check the cable connection between the router and the computer In order to make the whole network operate successfully it is necessary to configure the 150
10. in the PBC mode when you use the method 1 there will be session overlap Please using method 2 3 or wait for a while push the button again 4 3 3 WPS Configuration Display the WPS configuration information I 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual WPS Configuration Security Mode Authentication Type Kew Format Kev Mone Refresh Figure 4 17 4 4 Network 4 4 1 WAN This item provides two access types for you to configure the WAN parameters They are wired access and wireless access 4 4 1 1 Wired Access Access types wired access wireless access WAN Settings Internet Access Type DHCP dynamic IP 192 168 175 101 Subnet Mask 255 255 255 0 Gateway 192 168 175 1 _ tea Primary DNS _ Optional Secondary DNS _ Optional Connection Info Figure 4 18 gt Internet Access Type Ask for your ISP to get the correct access type gt IP The IP address you obtained after connect to the Internet if you haven t connected to the Internet yet this field 1s 0 0 0 0 Subnet Mask The Subnet mask you obtained after connect to the Internet if you haven t connected to Internet yet this field is 0 0 0 0 gt Gateway The IP address of Default gateway you obtained after connect to the Internet if you haven t connected to Internet yet this field 1s 0 0 0 0 gt MTU The MTU Maximum Transmission Unit setting specifi
11. the package contains above items If any of the above items is missing or damaged please contact the store you bought this product from Brand and Copyright Announcement Copyright O 2011Netis Corporation All rights reserved netis names may be used in this document to refer to either the entities claiming the marks and is a registered trademark of Netis Corporation Other trademarks and trade names or their products Reproduction in any manner without the permission of Netis Corporation is strictly forbidden All the information in this document is subject to change without notice 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Contents Ll INTRODUCTION A rrr 6 1 1 PRODUCT OVER VIE Wi nas tlar o 6 1 2 MAINE ATURE S a a a a 6 1 3 SUPPORTING STANDARD AND PROTOCOL ssceescoosccosseeesteesscsceeesscescccnsstasccessteessenssteescs 6 1 4 WORKING ENVIRONMENT id 7 Ze HARDWARE INSTALLATION as 8 Dido SYSTEM REQUIREMENT 4 sti ccc vos eo 8 222 lu Wd Ic eme 8 2 3 RESTORE TO FACTORY CONFIGURATION adas 10 2 4 HARDWARE INSTALLATION PROCEDURES eese eee nennen nnns eere rns erts tes nens 11 3 LOGIN laa a sa a k ena 12 Sul CONFIGURE COMPUTER Ri E 12 Jl VARAS Me o l a E cha 12 E PE RA Windows ZOO O she nai re ti 12 3 1 3 IS RR DR cece A A e are cep cel o 15 3 1 4 WINDOWS BO naa ass a k a crs R LS 18 Sado indo WS L skaka us teli Mc Mese du pp A aca a a aa ELLEN DD 3 1 6 MACOS EM m
12. 139 A PCI Fast Ethernet Adapter ia Displays the properties of the selected connection E Figure 3 2 4 Highlight Internet Protocol TCP IP and then press Properties button 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Local Area Connection 2 Properties ha when connect b Figure 3 3 5 Choose Obtain an IP address automatically and Obtain DNS server address automatically and then press OK to close the Internet Protocol TCP IP Properties window Internet Protocol TCP IP Properties Obtain an IP address automatically IP Sddress SUE mask Default gateway TEfeTren INS server Alternate DHS server Figure 3 4 6 Press OK to close the Local Area Connection Properties window 14 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Figure 3 5 3 1 3 Windows XP Please follow the steps below to setup your computer 1 Go to Start gt Settings gt Control Panel 2 Click Network and Internet Connections E Control Panel File Edit View Favorites Took Help V Control Panel A ck a category Je Switch to Classic View a a Appearance and a Printers and E Themes a Other Hardware See Also hh rs Windows Update o A p Network and 9 Help and Support Internet User Accounts Date Time Add or Remove Language and Programs fe Regional Options Figure 3 6 3 Click Network Connections 15 150 300Mbps Wireless N Long
13. 2 3 WEAS rr o de S O 41 4 5 2 4 II kst Send eive epa ucc t la sag ient dp dO P ul a 42 4 5 2 5 WEA WPA PSK iiti ba dd e do 42 4 5 3 Wireless MAC TAMANO Sa aa 43 4 5 4 WD SSCS PIT 43 4 5 5 Wireless ATV ee dodo 44 4 5 6 Eme LESS STE asa A MM MES O a aden 46 4 5 7 Mule AF SOM En 46 4 6 DIE O 47 4 6 1 PHCP SCUM S a slats c 47 4 6 2 DICE CHES da a ra a kar a h 47 4 6 3 JddyessdesePvattOHlousittssidsas DO 47 de FORWARDING aliada 48 4 7 1 As A aras Senet hace a 48 4 7 2 FOL MITIN A a i 48 4 7 3 DOM e E ices 49 4 7 4 Binder perc rcc Tp 49 4 7 5 FLF EVITO duret n ed crane odas 50 4 8 ssk 50 4 8 1 DECIS CU O sss rs kj ber R ere 50 4 8 2 PAJOS UI LA r E aa 51 4 6 3 DU ELI cp cc 22 4 8 4 Domain CINE Mm 53 4 9 STATIC ROUTING q assola cio 53 AO 005 SETTINGS knossast is 55 ALE DENAMICION Sd deL 55 q12 ESTEMOS sli pode data S6 diodo SA o E 56 4 12 2 MECENAS dies 56 223 PASSW d bones gg Sadi tse v aal b bm bba e 57 4 12 4 WOU ess casaa tecacee octal A a 57 A O T UU rm 57 5 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 4120 Remo Mandgement AAA A AA o Daan 58 412 7 Factory DJs ar barka 58 S RK a n E Mia 58 POND ABOUT R Ria 59 TROUBLESHOOTIN Gauss iii dd al 59 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual o 1 Introduction 1 1 Product Over
14. 24 3 2 CHECKING CONNECTION WITH THE ROUTER eese eene nene nennen eren eres nnns 26 3 3 MES agp PA O eet R DRNE 21 d ROUTERSETUP gene ON VMR R R OIN 29 4 1 STAR ta a salan A NE 29 4 1 1 VOS ded EET c tcc sco TRE NCO re Fe A PoE feel oe eed LE LO EL DICA 29 4 1 2 WAIN ited cise ay a H AR 29 4 1 3 DP n TROC EROR 30 4 1 4 VI sis ii in a Pa a a aid Pa a a 30 4 1 5 KOMI S NS ic id ER LLLI DL AR r DEUM 3 4 1 6 TETAS AS foge ct acti cipal on r 31 4 2 gie SET OP T T 31 4 2 1 PDI FONON uns cui SI sak 31 4 2 2 DP upset E MR C ME EM caa ela m REM 32 4 2 3 wor MM T nC ET 32 4 2 4 Wireless Con tO Fallo eicit A addet daB haat Rhea trans a ga US 33 AD MAC CONG es seas tibia 33 4 3 WEO0ODllNkeasumnuubtb u ll E a Mou eof 34 4 3 1 TESIS da aa 34 4 3 2 Add a Nem DEVICE id A A iaa 34 4 3 3 WAS C OTN OV sa easque epus to al aoe ES d ets 35 4 4 NEI sacs tata ll 36 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 4 4 1 A O A a a 36 4 4 1 1 WIN c 36 4 4 1 2 VAR A O A A 37 4 4 2 LAN a A 38 4 4 3 MC CIONES ED MI Te LEMMA LE MM AMNEM PE MEME 3 4 4 4 POTES CNS A a eii 38 4 4 5 TOMET TO V o putet sciet solo a estote thue Ro ee cie ME een ee 39 A WEEE e m CM m 39 4 5 1 WEE CUM TN ae 39 4 5 2 Wireless SECCU aedes cu tb Dus na ente open EO A e 40 4 5 2 1 NODC Pe E E E 40 4 5 2 2 WT E E E 41 4 5
15. 6 Extent 256 2346 Default 2346 Transmission Rate Auto ShortGi Enable Disable Protection Enable Disable Preamble Type Long Short WLAN Partition _ Enable Disable IAPP Enable Disable RF Output Power 100 7056 50 35 15 WMM Enable Disable High Power Enable Disable Save Figure 4 32 Authentications type The default is set to Auto which allows Open System or Shared Key authentication to be used Select Shared Key if you only want to use Shared Key authentication the sender and recipient use a WEP key for authentication Beacon Interval The interval time of this 150 300Mbps Wireless N Long Distance Broadband Router broadcast a beacon Beacon is used to synchronize the wireless network The valid interval is 20 1000 the default is 100 RTS Threshold You can set RTS Threshold value in this field the valid range should be 256 2347 and default value is 2347 If a network packet is smaller than the preset RTS threshold size the RTS CTS mechanism will not be enabled Aggregation You can accelerate the wireless transmission speed by enabling the aggregation function The default is AMPDU AMSDU Fragmentation Threshold It specifies the maximum size of packet during the fragmentation of data to be transmitted Transmission Rate Transmit rate indicates the transmission speed of wireless LAN access The default setting is Auto and you can set this valu
16. Distance Broadband RouterUser Manual Local Area Connection Properties e E General Authentication Advanced I Intel PRO 100 VM Network Connection Configure This connechon uses the Following tems EJ Chent for Microsoft Networks Fie and Printer Shanng for Microsoft Networks QoS Packet Scheduler Intemet Protocol TCP A1P Install insta Properties Desenpson Trancmassion Control Protocol Irnbemel Protocol The defauk vade area rebwork protocol that provides communication across dee inteeconnected networks Show icon in notification area when connected Figure 3 9 6 Choose Obtain an IP address automatically and Obtain DNS server address automatically and then press OK to close the Internet Protocol TCP IP Properties window Internet Protocol TCP IP Properties EJE General Altemate Configuration You can get P settings assigned automatically if your network supports this capability Otherwise you need to ask pour network administrator for the appropriate P settings 5 Obtain an IP address automatically O Use the following IP address Pere eme ea Subnet mask Default gateway Obtain DNS server address automatically O Use the following DNS server addresses Preferred DNS server Alternate DNS VEU RA Figure 3 10 7 Press OK to close the Local Area Connection Properties window 17 150 300Mbps Wireless N Long Distance Broad
17. Distance Broadband RouterUser Manual r E Network and Internet Connections File Edit wiew Favorites Tools Help Qe S pO search i Folders EB Address Network and Internet Connections Nt Network and Internet Connections See Also e My Network Places E Create a connection to the network at your workplace d Printers and Other Hardware EJ Set up or change your home or small office T Remote Desktop network a Phone and Modem Options or pick a Control Panel Icon Troubleshooters Home or Small Office Networking F z Network 2 Internet Explorer iM Internet Options e punctis Network Diagnostics Figure 3 7 4 Highlight the icon Local Area Connection right click your mouse and click Properties Network Connections FEE File Edit view Favorites Tools Advanced Help o Back amp 3 5 Ne Search I Folders EEK Address Network Connections bi A LAN or High Speed Internet Network Tasks a ocal Area Connection amp Create a new EIL connection Disable shwork 9 Set up a home or small Status office network Ls Disable this network device YY Repair this connection Repair Bridge Connections Create Shortcut Delete mi Rename this connection View status of this connection Rename Change settings of this Properties connection Figure 3 8 5 Highlight Internet Protocol TCP IP and then press Properties button 16 150 300Mbps Wireless N Long
18. E Encryption Type s TKIP AES TKIP amp AES Key Mode HEX ASCII please enter any 8 63 charcters ASCII charcters A Z a z 0 0 Key Renewal 86400 seconds 60 86400 Save Figure 4 27 gt Encryption type You can select the algorithm you want to use TKIP AES or TKIP amp AES TKIP means Temporal Key Integrity Protocol which incorporates Message Integrity Code MIC to provide protection against hackers AES means Advanced Encryption System which utilizes a symmetric 128 Bit block data gt Key Renewal you can configure the renewal time between 60 to 86400 seconds 41 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual gt Key Length description you need to input 8 to 63 ASCII characters no matter which type you select 4 5 2 4 WPA2 PSK The WPA2 PSK is similar to WPA PSK and with stronger encryption method than WPA PSK using WPA2 PSK you should input password leave this value in the range of 8 to 63 characters and key renewal time leave this value in the range of 60 to 86400 seconds Wireless Security For the security of your wireless network we strongly recommend you to use the authentication type of WPA2 PSK encryption type of AES or authentication type of WPA2 PSK encryption type of TKIP Authentication Type WPA2 PSK ga Encryption Type TKIP AES TKIP amp 4ES Key Mode HEX ASCII please enter any 8 63 charcters ASCII ii charcters A Z a z 0
19. Manual 4 5 2 2 WEP For the security of your wireless network we strongly recommend you to use the authentication type of WPA2 PSK encryption type of AES or authentication type of V PA2 PSK encryption type of TKIP Authentication Type WEP Key Length 64 bits 128 bits Key Mode O HEX 9 ASCII epi please enter any 5 charcters ASCII Charcters A Z a 7 0 0 Save Figure 4 26 gt Key Length There are two basic levels of WEP encryption 64 bits and 128 bits the more bits password have the better security wireless network is at the same time the speed of wireless 1s more slower Key Mode If you select WEP to encrypt your data choose the bits of password it should be 64 bits or 128 bits Then choose the format of password it should be HEX or ASCII The valid character for HEX format should be numbers from 0 to 9 and letters from A to F HEX support mixed letter and number mode And ASCII supports all characters that in keyboard Key Length description When you select 64bits you need to input 10 chars for HEX and 5 chars for ASCII and when you select 128bits you need to input 26 chars for HEX and 13 chars for ASCII Note When the WPS 1s enabled please not use WEP 4 5 2 3 WPA PSK For the security of your wireless network we strongly recommend you to use the authentication type of WPA2 PSK encryption type of AES or authentication type of VPA2 PSK encryption type of TKIP Authentication Type WPA PSK
20. Mode Tx Packet Rx Packet Tx Rate Mbps Power Saving Expired Time 5 Figure 4 33 46 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 4 6 DHCP 4 6 1 DHCP Settings DHCP Server Status Enable a Disable Start IP Add ress 192 168 1 2 End IP Address 192 168 1 63 Address Lease Time 86400 60 2592000 Seconds Figure 4 34 4 6 2 DHCP Clients List Display the state of assigned IP by DHCP Server DHCP Clients List Items show in every single page E 4 Gp Total 1 Pages ID IP Address MAC Address Status 1 192 168 10 2 00 1c c0 a2 d8 e3 Dynamic e 192 168 10 3 O0 e0 4c 07 79 fd Dynamic Figure 4 35 4 6 3 Address Reservation Address Reservation L Auto Setup MAC address IP Address Items show in every single page 3 Apply dc Y gt Total O Page ID IP Address MAC Address Del Figure 4 36 gt Address Reservation reserve IP address for designed physical address host If you want to configure a fixed IP address for some host please input physical address and IP address then click add 47 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 4 7 Forwarding 4 7 1 Virtual Servers tual Servers Description Internal Host IP Address Protocol External Port Internal Port Save _ Items show in every single page 3 1 Apply E lt bs w SITES Total O
21. N IP address 0 0 0 0 Subnet Mask 0 0 0 0 Default Gateway 0 0 0 0 Primary DNS Optional Secondary DNS Optional Figure 4 9 This item should only be used when users use a static IP address to access Internet you should input your WAN IP address subnet mask default gateway and DNS server domain name server according to the information provided by your ISP And every IP address should be input in appropriate IP field a IP address only divided into four IP octets by sign is acceptable gt WAN IP address The IP address that your Internet access into gt Subnet mask Specify a Subnet Mask for your WAN segment gt Default gateway It is provided by your ISP gt Primary DNS DNS server is used for resolve domain name Your ISP will provides you with at least one DNS IP address input IP address of your DNS server in this field gt Secondary DNS Input IP address of backup DNS server or you can leave this field blank 32 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 4 2 4 Wireless Configuration You can choose Enable or Disable to enable or disable the wireless function The default setting is enable If you chose the Disable status the router will become a wired broadband router without wireless function so be careful when you choose this status Wireless Status 9 Enable Disable SSID netis Region FCC Channel Authentication
22. Pages Guaranteed minimum bandwidth Restricted maximum bandwidth ID Comment IP Address Delete Uplink Bandwidth Downlink Bandwidth Uplink Bandwidth Downlink Bandwidth Figure 4 47 Status QOS switch Automatic Uplink Speed Router adjusts uplink bandwidth automatically Manual Uplink Speed Kbps User configures uplink bandwidth manually IP Address Set the IP address range for restricted hosts Minimum bandwidth setup uplink and downlink bandwidth V V V V V WV Maximum bandwidth setup uplink and downlink bandwidth 4 11 Dynamic DNS The DDNS feature allows you using domain name not IP address to access Internet Before you can use this feature you need to register an account for DDNS service at DDNS service providers such as roay cn TZO com DynDNS For more information you can visit http www oray net Help 33 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual DDNS Status O Enable Disable DONS Server Provider DynDNS Ga to register Username Password Dynamic Domain Name Status Figure 4 48 gt DDNS Status Current status of DDNS server gt DDNS Server Provider For example if you want to use service of roay cn you have to first register and accounts for it Other DDNS service providers as the same Username Password Dynamic Domain Name After register an DDNS account from DDNS service providers you will get User Name P
23. RX O o 192 168 2 3 gt Protocol and Port If the rule has already existed in Protocol Template You can select appropriate item and apply it Or you can input protocol type and port number manually click add button then the item will displayed in the list Follow the following steps to set Internet Access Control 1 You can select enable and click Save to enable IP Firewall function This is only the first step you should continue to create appropriate rules for IP Firewall 2 Input description information for current access control rule in the Description field Input IP address of host you want to restrict 3 There are two items supplied Permit through the router for IP address listed others are denied and Denythrough the router for IP address listed others are permitted Select the l 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual item you want and click Save button 4 If you want to delete certain item on the list select appropriate item on the list click delete to delete it 4 8 3 MAC Filtering Status Enable 9 Disable Deny through the router for MAC address listed others are permitted Filtering Rules Permit through the router for MAC address listed others are denied MAC Filter Management Description Rule Permit MAC Address C sun E Mon L Tue CI ved Ol Thu LI Fri Sat Times To Block A
24. Type Figure 4 10 SSID SSID Service Set Identifier is your wireless network s name shared among all points in a wireless network The SSID must be identical for all devices in the wireless network It is case sensitive and must not exceed 32 characters Make sure all points in the wireless network have the same SSID For added security you should change the default SSID to a unique name Region Choose a correct region which fit your use environment gt Channel Wireless router communicates to wireless cards in a particular channel which can reduce interference between different channels Authentication Type Different authentication types use different encryption types which can encrypt wireless data to protect your wireless communication 4 2 5 MAC Clone The WAN port of router has a unique MAC address assigned by manufacturer it called as Default MAC The Clone MAC is used for some special situations For example ISP only allows certain MAC address to access the Internet thus you can modify your WAN port s MAC address in accord with the requirement of ISP avoiding ISP s detection MAC Clone Do not set the same MAC address as the wirless network crad at the WISP model address WAN MAC Address 00 00 22 22 44 91 ERES EC Clone MAC Figure 4 11 33 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 4 3 WPS Settings Wi Fi Protect Setup WPS function ca
25. WE2501 WF2502 User Manual netis150 300MbpsWireless N Long Distance Broadband Router een V1 0 1141 Budapest Fogarasi ut 77 1095 Budapest Mester u 34 Tel 220 7940 220 7814 220 7959 Tel 218 5542 215 9771 215 7550 2012 02 13 220 8881 364 3428 Fax 220 7940 216 7017 216 7018 Fax 218 5542 CMS Mobil 30 531 5454 30 939 9989 Mobil 30 940 1970 20 949 2688 Www netis systems hu E mail info delton hu Web www delton hu 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Certification FCC CE FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and 1f not installed and used in accordance with the instructions may cause harmful interference to radio communications However there 1s no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equ
26. assword Dynamic Domain Name Input information in appropriate field 4 12 System Tools System management includes password setup web Setup upgrade reboot restore WOL and System time 4 12 1 Firmware Click Browse button and select a File to upgrade after you have selected the appropriate file click Upgrade button to execute upgrade procedure Do not cut off the power supply during the process of upgrading Version test version Upgrade File Upgrade Figure 4 49 4 12 2 Time Settings You can choose the time server and the time zone for the system time 56 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Current Time 01 18 2011 13 40 41 GMT GMT 08 00 Bejing Hongkong Singapore Taipei al Figure 4 50 4 12 3 Password The default username password is guest guest To ensure the Router s security it is suggested that you change the default password to one of your choice here enter a new password and then Re enter 1t again to confirm your new password Click Save button to save settings Password Old Username quest Old Password New Username New Password F we Confirm Mew Password Figure 4 51 4 12 4 WOL Input host MAC address and then click button of Wake up to wake up the target host which in the LAN Host MAC Address 00 00 00 00 00 00 Wake Up Figure 4 52 4 12 5 System Logs Exa
27. band RouterUser Manual k Local Area Connection Properties General Authentication Advanced Ea rnar per EE TES P 21005 Packet Scheduler V P nemet Protocol TCPAP Description Allows pour computer to access resources on a Micrasolt nelwark C Show icon in notification ares when connected R Figure 3 11 3 1 4 Windows Vista Please follow the steps below to setup your computer 1 Go to Start gt Settings gt Control Panel 2 Click Network and Sharing Center e Control Panel Name eee Control Panel Home Administrat AutoPlay Backup and d Color Date and Default Device Ease of Folder Fonts Game Indexing Hardware Tools Restore C DriveEn Management Time Programs Manager Acce Options Controllers Options t h A 2 72 S5 a a mei Internet iSCSIInitiater Keyboard Mouse Metworkand OfflineFiles Parental Pen and Pe Near Performance Personaliz Phone and Power Printers Options Sharing Ce Controls Input Devices Informatio Modem Options j ul d Z d e e B m di E 3 Problem Programs Regional and Scanners and Secure Security Sound Speech Sync Center System Tablet PC Taskbar and Text to User Reportsa and Features Language Cameras Online K Center Recogniti Settings Start Menu Speech Accounts Q 8 B P GE DD 5 VMware Welcome Windows Windows Windows Windows Windows Windaws Tools Center CardSpace Defender Firewall Sidebar SideShow Updat
28. e Figure 3 12 3 Click Manage Network Connections 18 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual vu Control Panel Network and Sharing Center Network and Sharing Center View computers and devices View full map Connect to a network hi Set up a connection or network A de e Manage network connections TECH PC Network Internet Diagnose and repair This computer du Network Private network Customize Access Local only Connection Local Area Connection View status a Sharing and Discovery Network e On v File sharing o Off x Public folder sharing Off v Printer sharing Off no printers installed v Password protected sharing 9 On v Media sharing o Off v Show me all the files and folders am sharing Shaw me all the shared network folders on this computer Figure 3 13 4 Highlight the icon Local Area Connection right click your mouse and click Properties e E Control Panel Network Connections v seah 1 2 Search a E Organize a Vj Views Disable t SEC thm T rework deve Ly Diagnose this connection C Rename this connection gt Name Status Device Name Connectivity Network Category Owner e Phone or Host Addre LAN or High Speed Internet 1 Local Area Connection i Network GE Intel R PRO 1000 MT Netw Disable Status Diagnose Bridge Connections Create Shortcut Delete Rename P
29. e between 1 54Mbps range gt ShortGi You can select Enable or disable for shortgi gt Protection Using 802 11b and 802 11g mixed mode may result in poor network performance By enabling 802 11 protection it will ameliorate performance of 802 11g devices in your wireless network Preamble Type Short Preamble is suitable for heavy traffic wireless network Long 45 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Preamble provides much communication reliability the default setting is Long Preamble High Power Enhanced signal booster increase coverage up to 4X than standard wireless N router 4 5 6 Wireless Statistics Display current status of the wireless client associate with AP Power Saving Expired Time s Figure 4 32 4 5 7 Multiple AP Settings The default status of secondary AP is disable you can select enable to enable the secondary AP Please refer to Quick SetupWireless Security and Wireless Statisticsfor details 41 T E TA f Lm LE en rrr ru E Pee PET MEEN ES Multiple AP Wireless Status _ Enable Disable Mule AP Wireless Seamily For the security of your wireless network we strongly recommend you to use the authentication type of a V PA2 PSK encryption type of AES or authentication type of WPA2 PSK encryption type of TKIP Authentication Type None kz Malte AP Wireless Statistics MAC Address
30. e the default SSID to a unique name Authentication Type None means do not encrypt wireless data gt Internet Access Type Ask for your ISP to get the correct access type gt IP The IP address you obtained after connect to the Internet if you haven t connected to the Internet yet this field 1s 0 0 0 0 Subnet Mask The Subnet mask you obtained after connect to the Internet if you haven t connected to Internet yet this field is 0 0 0 0 Gateway The IP address of Default gateway you obtained after connect to the Internet if you haven t connected to Internet yet this field 1s 0 0 0 0 gt MTU The MTU Maximum Transmission Unit setting specifies the largest packet size permitted for network transmission Most DSL users should use the value 1492 You can set MTU manually and you should leave this value in the 1200 to 1500 range If the value you set is not in accord with the value ISP provide it may causes some problems such as 37 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual fail to send Email or fail to browse website So if that happen you can contact your ISP for more information and correct your router s MTU value Primary DNS The DNS server translates domain or website names into IP address input the most common DNS server address you used or provided by your ISP Secondary DNS Input IP address of a backup DNS server or you can leave this field blank 4 4 2 LAN The IP add
31. ed for encapsulate and encrypt data across the public network For VPN tunnel the router supports IPSEC pass through PPTP pass through and L2TP pass through VPN Security Settings PPTP Pass through Enable Disable L2TP Pass through Enable Disable IPSEC Pass through 9 Enable Disable Figure 4 42 50 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 4 8 2 IP Address Filtering Status Enable Disable Deny through the router for IP address listed others are permitted Filtering Rules Permit through the router for IP address listed others are denied IP Filter List Management Description tle Permit v Source IP Address Protocol and Port All oo C sun O Mon E Tue C wed C Thu E Fri E sat Times To Block all Day 00 00 v 00 00 v Items show in every single page 3 amp A aF O v Total O Pages ID Description Source IP Destination Port Protocol Days To Block Times To Block Rule Del Figure 4 43 gt Status the default is disable The rules of Internet access control based on source IP Days To Block Everyday port number and protocol gt Description describe IP Firewall list to tell from different IP Firewall lists V Rule you can select permit or deny The default 1s permit Source IP address input the source IP address that you want to control The default format is ses
32. eless N Long Distance Broadband RouterUser Manual 3 Login You can manage the 150 300Mbps Wireless N Long Distance Broadband Router through the Web browser based configuration utility To configure the device via Web browser at least one properly configured computer must be connected to the device via Ethernet or wireless network The 150 300Mbps Wireless N Long Distance Broadband Router is configured with the default IP address of 192 168 1 1and subnet mask of 255 255 255 0 and its DHCP server is enabled by default Before setting up the Router make sure your PCs are configured to obtain an IP address automatically from the Router by the steps below 3 1 Configure computer 3 1 1 Windows 98 Me 1 Go to Start gt Settings gt Control Panel 2 Find and double click the Network icon The Network dialog box appears 3 Click the Configuration label and ensure that you have network card 4 Select TCP IP If TCP IP appears more than once please select the item that has an arrow gt pointing to the network card installed on your computer DO NOT choose the instance of TCP IP with the words Dial Up Adapter beside it 5 Click Properties The TCP IP Properties dialog box appears 6 Ensure the Obtain IP Address Automatically is checked 7 From the WINS Configuration dialog box Ensure that Disable WINS Resolution is checked 8 From the Gateway dialog box remove all entries from the Installed gateways by selecting t
33. es the largest packet size permitted for network transmission Most DSL users should use the value 1492 You can set MTU manually and you should leave this value in the 1200 to 1500 range If the value 36 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual you set is not in accord with the value ISP provide it may causes some problems such as fail to send Email or fail to browse website So if that happen you can contact your ISP for more information and correct your router s MTU value Primary DNS The DNS server translates domain or website names into IP address input the most common DNS server address you used or provided by your ISP Secondary DNS Input IP address of a backup DNS server or you can leave this field blank 4 4 1 2 Wireless Access Access types wired access wireless access Authentication Type Mone T Internet Access Type DHCP dynamic IP 0 0 0 0 Subnet Mask 0 0 0 0 Gateway 0 0 0 0 MTU 1496 Default value is 1496 do not change if not necessary Primary DNS Optional Secondary DNS Optional Figure 4 19 SSID SSID SSID Service Set Identifier is your wireless network s name shared among all points in a wireless network The SSID must be identical for all devices in the wireless network It is case sensitive and must not exceed 32 characters Make sure all points in the wireless network have the same SSID For added security you should chang
34. guration The default password is guest 3 I have some problems related to Connection with Cable Modem Please follow the following steps to check the problems Check whether the DSL modem works well or the signal 1s stable Normally there will be some indicator lights on the modem users can check whether the signal 1s ok or the modem works well from those lights If not please contact the ISP Check the front panel of the Router there are also some indicator lights there When the physical connection is correct the Power light and the CPU light should be solid the WAN light should be blinking If you use your computer the corresponding LAN port 59 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual light should be blinking too If not please check whether the cables work or not Repeat the steps in WAN Setup Connect with Internet through DSL Modem 4 I can browse the router s Web based Configuration Utility but cannot access the Internet Check if the WAN LED is ON If not verify that the physical connection between the router and the DSL Cable modem is firmly connected Also ensure the DSL Cable modem is working properly If WAN LED is ON open the System Overview page of the Web configuration utility and check the status group to see if the router s WAN port has successfully obtained an IP address Make sure you are using the correction method Dynamic IP Address PPPoE or Static IP as re
35. he setting of this field is disable wireless client can t obtain this SSID to login in then user have to input the SSID value manually gt Channel width This switch allows you to set Router s wireless bandwidth 20MHz In this mode you can get low bandwidth little interference and slow rate 40M Hz In this mode you can get high bandwidth high interference and rapid rate Use only when you have a pure router draft 802 11n wireless network Channel sideband It controls your wireless router use higher or lower channel when working on 40M Hz Region please select the region where you live in gt Channel In 20MHz you can select one channel from 1 to 13 manually and in 40M Hz you can select one channel from 1 to 9 or 5 to 13 which provides a choice of avoiding interference 4 5 2 Wireless Security The item allows you to encrypt your wireless communication and you can also protect your wireless network from unauthorized user access It supplies None WEP WPA PSK WPA2 PSK and WPA WPA2 PSK five different encryption modes 4 5 2 1 None None means do not encrypt wireless data For the security of your wireless network we strongly recommend you to use the authentication type of WPA2 PSK encryption type of AES or authentication type of WPA2 PSK encryption type of TKIP Authentication Type Mane Save Figure 4 25 40 150 300Mbps Wireless N Long Distance Broadband RouterUser
36. hem and clicking Remove 9 From the DNS Configuration dialog box remove all entries from the DNS Server Search Order box by selecting them and clicking Remove Remove all entries from the Domain Suffix Search Order box by selecting them and clicking Remove Click Disable DNS 10 Click OK back to Network Configuration dialog box 11 Click OK if prompted to restart click YES 3 2 Windows 2000 Please follow the steps below to setup your computer 1 Go to Start gt Settings gt Control Panel 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual El Control Panel Fle Edt wew Favorites Tools Mep M eu 7o gt J ser Faldas Qi UE Control Panes Control Panel Opes Metwork and Dial up Conmections A Connects Lo other computers Fat works Acid ther Doi ernst Windays Lipdake Windoees 2000 Support Figure 3 1 2 Double click the icon Network and Dial up Connections 3 Highlight the icon Local Area Connection right click your mouse and click Properties E Network and Dial up Connections File Edit View Favorites Tools Advanced Help tg Search F Folders i Rs P h x E EE Exe Address ie Network and Dial up Connections o Make Mew Local Area Network and Dial up Connection Connection Connections Disable Status Create Shortcut Local Area Connection 2 Delete Type LAM Connection Rename Status Enabled Properties Realtek RTL8
37. ipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help To assure continued compliance any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Example use only shielded interface cables when connecting to computer or peripheral devices FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This transmitter must not be co located or operating in conjunction with any other antenna or transmitter This equipment complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Caution The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user authority to operate the equipment 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Package Contents The following items should be found in your package 150 300Mbps Wireless NLongDistanceBroadband Router Power adapter Quick Installation Guide CD Rom V V V V WV Ethernet cable Make sure that
38. ireless adapter and the router in a safe way If you have a wireless network card which has WPS button you may set up a safe network via the following methods Method 1 34 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 1 Push the WPS button in the Router until the WPS LED is flashing several times 2 Push the WPS button in the wireless network cardfor about 3 5seconds 3 The safe connection will be established automatically Method 2 1 Input the PIN code of the adapter s WPS page into the router s WPS configure page then click connect Wi Fi Protected Setup WPS An easy and secure setup solution for Wi Fi network Pin Input Config PIN After pushing the PIM button Please enter the PIN cade into your AP PIN Code 35229155 Figure 4 14 2 Enter the new device s PIN 35229155 Figure 4 15 2 Push the PIN Input Config PIN in the Wi Fi protect setup of the adapter PIN Code 35229155 Pin Ingu Config PIN Figure 4 16 3 Select this router in the pop up window then click Select 4 The connection between the adapter and the router is be established automatically Method 3 1 Select Input PIN from AP in WI FI protect setup page input PIN of the router then click PIN Input Config PIN 2 Select this router in the pop up window then click Select 3 The connection between the adapter and the router 1s be established automatically Remark If there 1s more than one AP
39. l background and our sincerity and trustworthiness when working with customers Vvith more than 8 years of manufacturing experience Metis delivers the best in class solutions to its worldwide customers Through continual efforts on technology innovation customer satisfaction and market development Link beyond network Metis would like to establish the links for the people for the world Figure 4 57 Thank you for your support 5 Iroubleshooting 1 I cannot access the Web based Configuration Utility from the Ethernet computer used to configure the router V Check that the LAN LED 1s on If the LED is not on verify that the cable for the LAN connection is firmly connected Check whether the computer resides on the same subnet with the router s LAN IP address If the computer acts as a DHCP client check whether the computer has been assigned an IP address from the DHCP server If not you will need to renew the IP address Use the ping command to ping the router s LAN IP address to verify the connection Make sure your browser 1s not configured to use a proxy server Check that the IP address you entered is correct If the router s LAN IP address has been changed you should enter the reassigned IP address instead 2 I forget Password Reset the Router without Login Use a pencil to press the button for about 2 6 seconds when it is working then leave your hands it will restore settings to the factory confi
40. ll Day 00 00 v Days To Block Everyday Items show in every single pages RR EQ IE Total O Pages ID Description MAC Address Days To Block Times To Block Rule Del Del All Figure 4 44 gt Status the default is disable You can filter wired users by enabling this function thus unauthorized users can not access the network gt Description describe MAC Filter list to tell from different MAC Filter lists gt Rule you can select permit or deny The default is permit gt MAC address input the MAC address that you want to control The default format is kkk ek kk AK EK Cog 00 22 33 da cc bb Follow the following steps to set MAC filter 1 Enable MAC Filter then select save 2 Add MAC address you want to control in the MAC address field the format is kk Lick AeA k k then click Add button and you will see the MAC address has displayed in the MAC list 3 There are two items supplied Permit wireless connection for MAC address listed others are Denied and Deny wireless connection for MAC address listed others are Permitted Select the item you want and click Save button Z 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 4 8 4 Domain Filtering Status Enable Disable O Deny through the router for DHS Key words listed others are ee Permitted Filtering Rules Permit through the router for DNS Key words listed others are e Denied DNS Fil
41. ll wireless bridge that in connection status you may delete unnecessary bridge E g If you want setup WDS connection between the AP that the MAC address is 00 22 4f cc ae f5 we call it AP1 and the AP that the MAC address is 00 22 Af bc af 5d we call it AP2 please follow the next steps 1 Select radio mode is WDS in wireless management basic of AP1 2 Input WDS name e g default input MAC address of AP2 00 22 4f bc af 5d click add then the record named default will appears in WDS list 3 We can also select radio mode is WDS in wireless management basic of AP2 4 Input WDS name e g Default input MAC address of AP1 00 22 4f cc ae f5 click add then the record named Default will appears in WDS list Note Before you setup WDS connection please make sure that AP1 and AP2 is in the same network that is if the IP address of AP1 is 192 168 1 1 then the IP address of AP2 should be 192 168 1 x 1 lt x lt 255 e g x 8 4 5 5 Wireless Advanced These settings are only for more technically advanced users who have a sufficient knowledge about wireless LAN These settings should not be changed unless you know what effect the change will have on your AP 44 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Authentication Type Auto E Beacon Interval 100 Extent 20 1000 Default 100 RTS Threshold 2347 Extent 256 2347 Default 2347 Aggregation AMPDU AMSDU Fragmentation Threshold 234
42. mine system logs You can configure items shown in one Page the default is 10 57 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual aystem Logs Items show in every single page 10 Figure 4 53 4 12 6 Remote Management WEB Management Status the default is disable Router can be accessed on the remote site using Web setup Check the Management Port and enter the port number and then press save button to enable web management Remote Management E WEB Management Status Enable Disable Management Port 8080 Figure 4 54 4 12 7 Factory Defaults Click Restore button the Router will erase all of your settings and replace them with the factory defaults make sure you have backup current settings before click this button Factory Defaults Restore Figure 4 55 4 12 8 Reboot Click Reboot button to restart the router Reboot Reboot Figure 4 56 58 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 4 13 About OO About Metis was founded in China in 2000 45 a world known network communications manufacturer the company is mainly committed ta the research development and production of layer 2 Management Ethernet Switch Wireless Client Adapter Wireless LAN amp P router SOHO Router Ethernet Switch Media Converter YWeb Smart Switches and Ethernet MIC The company grew quickly in the 2000 s due to our powerful technica
43. mode at this point the router can be used as wired and wireless signal converter In this mode you can use wireless access instead of cable access Mostconnections utilize a dynamic ip DHCP and the default is already set to this If you have another connection type like static User you will need to click on Quick Setup in 60 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual the menu and input information given you by your service provider and then click save WDS 1r you are using this router to spread the wireless coverage of another router or to spread the coverage to another router you can use WDS mode gt You can configure the routerfollowing the steps in 4 5 4 AP WDS You can bridge two LAN or two computers via two AP the wireless signal will be amplified and transmitted at the same time gt You can configure the router following the steps in 4 5 4 Client In this mode the router function 1s approximately equal to a wireless adapter you can make a wireless connection to the internet Attach one end of an Ethernet cable to your computer s port and the other end to one of the LAN ports of your router Configure Your Computer 99 66 Select wireless wireless settings select the client mode click on AP scan and you will see a new window options select the AP you want to connect to and click the connect button below gt Ifyour AP is notencrypted click
44. n let you create a safety network easily You can through PIN Input Config PIN or Push Button PBC to encrypt your network This router also provides WPS button you only need to push the WPS button in this router and the wireless network card that support WPS function then the router will be encrypted to WPA2 AES mode automatically Note If you have configured encryption mode in your router then when you use this WPS function please configure the authentication type to none and then it will be encrypted to WPA2 AES mode automatically If you don t want to change your authentication type then when you use this function the router will be encrypted to the mode that you have configured 4 3 1 WPS Settings WPS Status Enable Disable WPS AP PIN Code 22457760 Restore PIN Gen New PIN _ Add A New Device RRE Figure 4 12 gt WPS Status You can use this function to setup the wireless connection between this router and wireless network card The default is Enable gt APPIN Code This code can mark a wireless product gt Add A New Device Add a new device by WPS 4 3 2 Add a New Device Enter the new device s PIN O Press the button of the new device in two minutes Connect Figure 4 13 gt Enter the new device s PIN This code can mark a wireless product gt Press the button of the new device in two minutes New device will send a PIN code to wireless router WPS can connect the w
45. ng Distance Broadband RouterUser Manual Static Routing ID Type Destination Network or IP address Subnet Mask Next Hop IP address Items show in every single page 3 Apply amp s 0 Total Pages Type Dst IP address Mask Mext hop address Ciel Figure 4 46 Destination Network or IP Address Specify a certain destination Network or IP address which static route forward to Subnet Mask Subnet mask 1s used for distinguish Network portion and Host portion for an IP address Next hop IP Address This is an IP address of the next hop device and also is the gateway address for local host that allows forwarding data between router and remote network or host Routing Table You can check out all current route items click delete button to delete a route item existed in routing table 54 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 4 10 QOS Settings 205 Configaratioa Status C Enable Disable Automatic Uplink Speed Manual Uplink Speed O KB s Uplink Speed Setup Automatic Downlink Speed Manual Downlink Speed 0 KB s Save Downlink Speed Setup Comment 11 IP Address 192 168 1 192 168 1 _ Guaranteed minimum bandwidth Uplink Bandwidth KB s 0 Downlink Bandwidth KB s 0 Restricted maximum bandwidth Uplink Bandwidth KB s 0 Downlink Bandwidth KB s 0 Add Items show in every single page 3 Y 4 Total 0
46. nnections P Organize Disable this network device Diagnose this connection Rename this connection Hi Disable Status Diagnose Bridge Connections Create Shortcut Us Delete Rename Properties Figure 3 18 You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically 5 Use the following IP address IP address Subnet mask Default gateway Obtain DNS server address automatically 5 Use the following DNS server addresses Preferred DNS server Alternate DMS server Validate settings upon exit Figure 3 19 Choose Obtain an IP address automatically and Obtain DNS server address automatically 29 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual and then press the OK to close the window You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically 7 Use the following IP address IP address Subnet mask Default gateway Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate OAS server _ Validate settings upon exit Figure 3 20 6 Press OK to close
47. permit or deny The default is permit gt MAC address input the MAC address that you want to control The default format is kk kk ek kk kk EK Ce g 00 22 33 da cc bb Follow the following steps to set MAC filter 1 Enable MAC Filter then select save 2 Add MAC address you want to control in the MAC address field the format is dk Lick ek oes k then click Add button and you will see the MAC address has displayed in the MAC list 3 There are two items supplied Permit wireless connection for MAC address listed others are Denied and Deny wireless connection for MAC address listed others are Permitted Select the item you want and click Save button 4 5 4 WDS Settings If you have selected WDS or AP WDS mode in Wireless Basic Radio Mode please do the following configurations 43 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual WDS Mame AP Scan WDS MAC Address Items show in every single page 3 EA O Total O Pages ID WDS Name WDS MAC Address Del Figure 4 2 gt WDS Name Give a description of your wireless bridge to tell apart gt WDS MAC Address If the current working mode is WDS or AP WDS then you need to configure wireless bridge configuration Enter MAC address of remote access point at the same time the remote access point also need to configure to WDS or AP WDS mode Current WDS Information It illustrates basic information of a
48. quired by the ISP Also ensure you have entered the correct settings provided by the ISP For cable users if your ISP requires a registered Ethernet card MAC address make sure you have cloned the network adapter s MAC address to the WAN port of the router See the MAC Address field in WAN Setup 5 My wireless client cannot communicate with another Ethernet computer gt Ensure the wireless adapter functions properly You may open the Device Manager in Windows to see if the adapter is properly installed Make sure the wireless client uses the same SSID and security settings 1f enabled as the 150 300Mbps Wireless N Long Distance Broadband Router Ensure that the wireless adapter s TCP IP settings are correct as required by your network administrator If you are using a 802 11b wireless adapter and check that the 802 11G Mode item in Wireless Basic Setting page is not configured to use 802 11G Performance Use the ping command to verify that the wireless client is able to communicate with the router s LAN port and with the remote computer If the wireless client can successfully ping the router s LAN port but fails to ping the remote computer then verify the TCP IP settings of the remote computer 6 I don t know how to use the router in different modes You can select radio mode of wireless routerin wireless wireless settings it contains Access Point WDS AP WDS Client and Repeater AP The default setting is AP
49. redefined Rules Rule Name describe one Predefined Trigger that you will configure Trigger Protocol you can select TCP UDP Trigger Port you can select a part of ports Forward Protocol you can select TCP UDP V V V V V WV Forward Port you can select a part of ports 4 7 3 DMZ DMZ opens all the ports of one computer exposing the computer to the Internet So it should only be used for some special purpose especial for Internet online games Using this function you can select DMZ item and input IP address of DMZ host then click Save For the purpose of security we suggested that using Virtual servicer instead of DMZ DMZ Status O Enable 9 Disable DMZ Host IP Address 0 0 0 0 uper DMA Super DMZ Status C Enable Disable MAC Address 00 e0 4c 07 79 fd Figure 4 39 4 7 4 UPnP The UPnP function supports load Application s port forward record automatically Select Enable to enable this function 49 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual UPnP Figure 4 40 4 7 5 FTP Private Port Some games servers and applications such as BT QQ video Edunkey Web server are no longer effect when behind the NAT router so this item provides function of port mapping from LAN to WAN Status Enable 9 Disable Port Number a Figure 4 41 4 8 Security 4 8 1 Security Settings VPN is commonly us
50. ress of LAN port is used for access router itself by computers that connect to the router directly here you can set IP address you need The IP address format is like ck RRR kkk kkk and default IP address is 192 168 1 1 the default subnet mask is 255 255 255 0 MAC Address 00 00 22 22 44 90 IP Address 192 168 10 1 Subnet Mask 255 255 255 0 Figure 4 1 44 3 MAC Clone The WAN port of router has a unique MAC address assigned by manufacturer it called as Default MAC The Clone MAC is used for some special situations For example ISP only allows certain MAC address to access the Internet thus you can modify your WAN port s MAC address in accord with the requirement of ISP avoiding ISP s detection AA Pin MAC LICHE ha Do not set the same MAC address as the wirless network card at the WISP mode WAN MAC Address 00 e0 4c 01 02 c9 Restore Factory MAC Clone MAC address Figure 4 21 44 4 Port Settings Here you can set the router s WAN and LAN interfaces work at 100M duplex 100M half duplex 10M duplex and 10M half duplex communication mode 38 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual WAN Port LAMI Port LANZ Port LAN Port LAN Port Figure 4 22 4 4 5 IGMP Proxy Here you can set the IGMP Proxy Enabled and Disabled IGMP Proxy Status O Enable Disable Figure 4 23 4 5 Wireless 4 5 1 Wireless Settings Providing ba
51. ress of a backup DNS server or you can leave this field blank Link Status Show the current status of link information You can choose connect or disconnect by manually 4 1 3 LAN This item provides information about router s LAN port display LAN port s physical address IP address and current situation of DHCP server MAC Address 00 e0 4c 00 03 04 IP Address 192 168 1 1 Subnet Mask 255 255 255 0 DHCP Server Enable Figure 4 3 4 1 4 Wireless This item provides current running information of wireless Wireless Status Enable Name 5SID netis Mode AP Channel AUTO MAC Address 00 e0 4c 81 96 c1 WPS Status Disabled Figure 4 4 Wireless status Display wireless interface status 1s enabled or not Name SSID SSID Service Set Identifier is your wireless network s name shared among all points in a wireless network Mode Current wireless mode of wireless router Channel Display current channel of your wireless router gt MAC Address The MAC address is used for wireless communication 30 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual WPS Status Display WPS Wi Fi Protected Setup status is enabled or not 4 1 5 Router Status This item provides current running information of System Router Status System Uptime O Days 5 hours 48 minutes 19 seconds CPU Usage 1 Memory Usage 5 Figure 4 5 4 1 6 Traffic Statistics This item provides statistics info
52. rmation about the bits router sends and received Statistics Traffic Type Sending Packets Receiving Packets Sending data KBytes Receiving data KBytes LAM 60814 70162 42299 0 02 WAN 24309 33908 2318 32401 WLAN 29041 250451 3884 46194 Refresh Figure 4 6 4 2 Quick Setup Providing you the convenient and simplest method for configure the router the purpose of this item 1s to provide an easy way for you to use it and configure your router to access the Internet quickly including DHCP dynamic PPPoE Static and Wireless Configuration This is the most convenient tool for you to configure router 4 2 1 DHCP dynamic After select this item you will obtain an IP address from your ISP automatically those ISP who supply Cable modem always use DHCP technology Figure 4 7 31 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual 422 PPPoE Connection Type v Username Password Figure 4 8 If your ISP provides you the PPPoE service all ISP with DSL transaction will supply this service such as the most popular ADSL technique please select this item In the Convenient configuration You can input your PPPoE username and password to access the Internet gt PPPoEUsername Input PPPoE username provided by ISP gt PPPoE Password Input PPPoE password provided by ISP 4 2 3 Static Connection Type WA
53. roperties Figure 3 14 5 Highlight Internet Protocol Version 4 TCP IP and then press Properties button 19 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual EP InteR PRO 1000 MT Network Connection This connection uses the following items o Client for Microsoft Networks dE 005 Packet Scheduler B File and Printer Sharing for Microsoft Metworks Intemet Protocol Version 6 TCP IPv5 Intemet Protocol Version 4 dE alm ak Link Layer Topology Discovery Mapper 10 Driver e ink Layer Topology Discovery Responder Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Description Figure 3 15 6 Choose Obtain an IP address automatically and Obtain DNS server address automatically and then press OK to close the Internet Protocol TCP IP Properties window 20 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically E Use the following IP address IP address Subnet mask Default gateway Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server Figure 3 16 7 Press OK to close the
54. sic configuration items for wireless router users including wireless network status SSID Radio Band Radio Mode MAC SSID broadcasting Channel width Channel sideband Region and Channel severalbasic configuration items ar He E Wireless Status Enable Disable SSID netis Radio Band 802 11b g n Radio Mode Access Point 7 MAC 00 e0 4c 81 96 c1 SSID Broadcast 2 Enable Disable Channel Width 20MHZ 40MHZ M M Control Sideband Lower J Upper Region FCC M Channel Auto d Save Figure 4 24 39 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Wireless network status You can choose enable or disable to enable or disable the Wireless Network Status 1f what you choose is Disable the AP function of wireless router will be turned off SSID The default is netis gt Radio band You can select the wireless standards running on your network if you have Wireless N and Wireless B G devices in your network keep the default setting 802 11b g n Radio mode You can select radio mode of wireless router it contains Access Point Client AP WDS and WDS The default setting is AP mode MAC Wireless router s physical address SSID Broadcasting You can select enable or disable to enable or disable the broadcast SSID function If t
55. ter List Management Rule Permit EJ DNS Filter Key words C sun El Mon Tue C wed Thu Fi sat Times To Black All Day 00 00 v Days To Black Everyday Itemsshow in every single pages Apply Bes f t p o 4 Total O Pages ID DMS Filter Key words Days To Black Times To Block Rule Del Del All Figure 4 45 Status the default is disable DNS filter is able to filter certain domain name such as www sina com Rule you can select permit or deny The default is permit gt DNS Filter Key words Input website name or Domain name in the DNS Key Words field such as www 163 com Follow these steps to set DNS filter 1 You can select enable and click Save to enable DNS Filter function This 1s only the first step you should continued to create appropriate rules for DNS Filter 2 InputDNS Filter Key words 3 There are two items supplied Permit through the router for DNS Key words listed others are denied and Denythrough the router for DNS Key words listed others are permitted Select the item you want and click Save button 4 If you want to delete certain item on the list select appropriate item on the list click delete to delete 1t 4 9 Static Routing Most of broadband router and wireless router are using NAT mode so this feature is designed for most common network environment 25 150 300Mbps Wireless N Lo
56. the Local Area Connection Properties window 3 1 00 MAC OS Please follow the steps blow to setup your computer l Goto Start gt System preference Settings Network 24 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Spaces Text a E 1 io Keyboard Mouse Trackpad Print amp Fax Sharing o y Speech Software Startup Disk Time Machine Universal Update Access Figure 3 21 2 Click Network Select Use DHCP at the Configuration bar the system will get the IP address automatically Connected Ethernet is active IP address is 19216812 Configuration IP address 19216812 Subnet Mask 2552552550 Router 19216811 DNS Server 192 168 245 2 Search Area localdomain CoO id Click on the button to prevent second changes d Figure 3 22 25 150 300Mbps Wireless N Long Distance Broadband RouterUser Manual Press Apply to complete this operation and close the window 3 2 Checking Connection with the Router After configuring the TCP IP protocol use the ping command to verify 1f the computer cancommunicate with the Router To execute the ping command open the DOS window andPing the IP address of the 150 300MbpsWireless N Long Distance Broadband Router at the DOS prompt gt For Windows 98 Me Start gt Run Type command and click OK gt For Windows 2000 XP Start gt Run Type cmd and click OK gt For Windows Vista 7 Start Type cmd
57. view WF2501 WF2502 is a powerful enhanced enterprise level product supports 5 multi functions to operate for every kind of working environment It supports high transmit output power and high data rate which plays different roles of Access Point WDS Repeater AP WDS Client Bridge It operates seamlessly in the 2 4 GHz frequency spectrum supporting the 802 11b g n wireless standards Configured up to 1000mW wireless power with 5dBi upgradable antenna it provides up to 4 time signal coverage This device also encrypts all wireless transmissions by WPA2 WPA WEP data encryption for your data safety 1 2 Main Features gt Comply with IEEE802 11n g b IEEES02 3 10Base T IEEES802 3u 100Base TX standards support DHCP Client PPPoE Chent Static IP High 1000mW Wireless Power and High Gain Detachable Antenna Design Enhanced signal booster increase coverage up to 4X than standard wireless N router Rx sensitivity has 3096 of ascension comparing with common products Support 7 Modes Access Point Client Bridge Repeater Router Client Router WDS Support static ARP MAC filtering IP access control DNS filter support FTP PPTP and L2TP pass through Support UPNP universal plug and play Upgradeable firmware for future functions Upgradeable antenna to increase range and receive sensitivity WPS button can easily setup a secure network Support data encryption mode WEP WPA WPA2 support WMM support DMZ VVV V V V V V V V V V V WV
Download Pdf Manuals
Related Search