UHO Camera Housings Installation manual
Contents
1. Ensure that all holes are covered with the rubber plugs provided Close the cover and secure the latches Optional tamper resistant screws are provided with the housing If desired secure the latch using these three screws and the provided tamper resistant wrench 6 4 3 Positioning sunshield 1 Loosen the two screws M4 x 10 on the top of the housing 2 Slide the sunshield to the desired position It has a range of 50 mm 2 in 3 Tighten the screws to lock the sunshield into position 4 Ifthe sunshield is not installed seal the two screw holes with the plugs supplied 2x Sunshield 2014 10 5 0 F 01U 167 418 Installation Manual Bosch Security Systems UHO Camera Housing 7 7 1 Maintenance Maintenance en 21 No special maintenance is required other than occasionally cleaning the window with water or any non aggressive liquid Fuse replacement 1 To replace a fuse push and twist the fuse holder to open it Replace the fuse with a fuse that has the same current rating The fuse is a5 mm x 20 mm slow blow breaking capacity cartridge type fuse 3 Push and twist the fuse holder to close it Housing voltage Fuse rating 24 VAC 4 A 250 VAC 120 VAC 2 A 250 VAC 230 VAC 2 A 250 VAC There is a spare fuse inside the housing Bosch Security Systems Installation Manual 2014 10 5 0 F 01U 167 418 22 en Decommissioning UHO Camera Housing 8 Decommiss2. UHO Camera Housing UHO HBPS UHO HBGS UHO HGS UHO HPS BOSCH en Installation Manual UHO Camera Housing Table of contents Table of Contents en 3 1 Safety 4 1 1 Safety message explanation 4 1 2 Safety precautions 4 1 3 Important safety instructions 5 1 4 FCC and ICES compliance 6 2 Short information 7 3 System overview 8 3 1 Available models 8 4 Planning information 9 4 1 Parts list 9 4 2 Unpacking 10 4 3 Tools required 10 5 Installation 11 5 1 Camera lens requirements 11 5 2 Housing mounting 12 5 3 Opening the cover 12 5 4 Feed through cables 13 5 4 1 Feed through power cables 13 5 4 2 Feed through wiring through the base 13 5 4 3 Feed through wiring through the rear 13 5 5 Camera Lens installation 14 59 541 Camera tray mount 14 5 5 2 Mounting the camera tray in the housing 15 6 Connection 16 6 1 Feed through power connection 16 6 1 1 Incoming power safety earth connection 16 6 1 2 Incoming power wires 17 6 2 Camera connections 18 6 2 1 Camera video connections 18 6 2 2 Camera power connections 18 6 3 Housings with rear connectors 19 6 3 1 Connection UHO Rear housing video connection 19 6 3 2 Connection UHO Rear housing power connection 19 6 4 Final assembly 20 6 4 1 Camera operation 20 6 4 2 Closing the housing 20 6 4 3 Positioning sunshield 20 7 Maintenance 21 71 Fuse replacement 21 8 Decommissioning 22 Bosch Security Systems Installation Manual 2014 10 5 0 F
3. 01U 167 418 4 en Safety m UHO Camera Housing Safety Safety message explanation Danger Indicates a hazardous situation which if not avoided will result in death or serious injury Warning Indicates a hazardous situation which if not avoided could result in death or serious injury Caution Indicates a hazardous situation which if not avoided could result in minor or moderate injury Notice Indicates a situation which if not avoided could result in damage to the equipment or environment or data loss a N Safety precautions Warning Hazardous voltage Use caution when working inside the housing Hazardous voltage is present in the housing when connected to the AC supply Do not touch the power terminals when the unit is powered Caution Installation should only be performed by qualified service personnel in accordance with the National Electrical Code NEC 800 CEC Section 60 or applicable local codes Caution This device must be connected to earth ground Safety power ground is indicated by the symbol Caution These units must be properly and securely mounted to a supporting structure capable of sustaining the unit weight Use care when selecting mounts or pan tilts not supplied for installation the mounting surface and unit s weight should be carefully considered PEBBE Ee HD DD Caution To protect the device the branch c
4. model Quantity Item Material 1 4 pin cable connector Male ABS UHO HPS 51 and UHO HBPS 51 models Quantity Item Material 1 4 pin cable connector Female ABS Bosch Security Systems Installation Manual 2014 10 5 0 F 01U 167 418 10 en Planning information UHO Camera Housing 4 2 Unpacking This equipment should be unpacked and handled with care If an item appears to have been damaged in shipment notify the shipper immediately Verify that all parts are included If any items are missing notify your Bosch Security Systems Sales or Customer Service Representative The original packaging is the safest container in which to transport the unit and can be used if returning the unit for service 4 3 Tools required Small flat blade screwdriver Phillips screwdriver 1 Adjustable wrench Wire cutter stripper crimper tool 2014 10 5 0 F 01U 167 418 Installation Manual Bosch Security Systems UHO Camera Housing 5 Installation en 11 Installation Caution Installation should only be performed by qualified service personnel in accordance with the National Electrical Code NEC 800 CEC Section 60 or applicable local codes 5 1 Caution These units must be properly and securely mounted to a supporting structure capable of sustaining the unit weight Use care when selecting mounts or pan tilts not supplied for installation the mountin
5. at least 3 mm into the electrical installation of the building If it is needed to open the housing use this all pole switch as the main disconnect device for switching off the voltage to the unit Coax grounding Ground the cable system if connecting an outside cable system to the unit Connect outdoor equipment to the unit s inputs only after this unit has had its grounding plug connected to a grounded outlet or its ground terminal is properly connected to a ground source Disconnect the unit s input connectors from outdoor equipment before disconnecting the grounding plug or grounding terminal Follow proper safety precautions such as grounding for any outdoor device connected to this unit Section 810 of the National Electrical Code ANSI NFPA No 70 provides information regarding proper grounding of the mount and supporting structure grounding of the coax to a discharge unit size of grounding conductors location of discharge unit connection to grounding electrodes and requirements for the grounding electrode Bosch Security Systems Installation Manual 2014 10 5 0 F 01U 167 418 6 en Safety UHO Camera Housing 1 4 FCC and ICES compliance FCC amp ICES Information U S A and Canadian Models Only This device complies with part 15 of the FCC Rules Operation is subject to the following conditions this device may not cause harmful interference and this device must accept any interference
6. e Model Input voltage Connection Temperature control UHO HBGS 11 24 VAC Feed through Fan UHO HBGS 51 230 VAC Feed through Fan UHO HBGS 61 115 VAC Feed through Fan UHO HGS 11 24 VAC Feed through Passive UHO HGS 51 230 VAC Feed through Passive UHO HBPS 11 24 VAC Power and BNC connectors Fan UHO HBPS 51 230 VAC Power and BNC connectors Fan UHO HPS 51 230 VAC Power and BNC connectors Passive All models have an internal 12 VDC power supply available for the camera Alternatively the input voltage is also available to power the camera 2014 10 5 0 F 01U 167 418 Installation Manual Bosch Security Systems UHO Camera Housing Planning information Parts list Planning information en 9 Quantity ltem Material 1 Housing Aluminum 1 Spacer 4 mm ABS 1 Spacer 9 mm ABS 1 Screw 1 4 20 x 3 8 in Stainless Steel 1 Screw 1 4 20 x 3 4 in Stainless Steel 3 Screw tamper resistant M3 5 T15 1 Wrench tamper resistant M3 5 T15 1 Camera clamp Stainless Steel 1 Camera clamp for spacer ABS 2 Washer flat M6 Stainless Steel 2 Washer spring M6 Stainless Steel 3 Plug M4 Silicone UHO HGS AND UHO HBGS models Quantity ltem Material 2 Cable gland 3 8 in NPT with locking nut Polyamide neoprene 1 Cable gland 1 2 in NPT with locking nut Polyamide neoprene 1 Cable gland M20 x 1 5 Polyamide neoprene UHO HBPS 11
7. g surface and unit s weight should be carefully considered Camera lens requirements The camera lens combination to be built into the housing must meet the following requirements Maximum power consumption 10W Maximum weight 1 kg 2 2 Ib Maximum size H x W x D 91 x 81 x 262 mm 3 6 x 3 2 x 10 3 in d tu D 81 3 2 262 10 3 Bosch Security Systems Installation Manual 2014 10 5 0 F 01U 167 418 12 en Installation UHO Camera Housing 5 2 Housing mounting 1 Use two 1 4 20 x 0 50 in screws and two 1 4 in spring washers to mount the housing to a mount or a pan tilt The spring washers must be used for a secure connection 2 The outermost set of 1 4 20 threaded holes 2 are for mounting to feed through mounts and the innermost 1 4 20 threaded holes 1 are for mounting to all other mounts and pan tilts 5 3 Opening the cover Caution The heater will be hot when in operation Do not touch Always ensure that the heater is off and cool before working on the camera Open the cover by unlatching the three latches 1 on the side of the housing If the optional tamper resistant screws have been installed use the supplied wrench to remove the screws before opening the latches 2014 10 5 0 F 01U 167 418 Installation Manual Bosch Sec
8. ing Short information en 7 2 Short information This manual has been compiled with great care and the information it contains has been thoroughly verified The text was correct at the time of printing however the content can change without notice Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults incompleteness or discrepancies between this manual and the product described Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly More information For more information please contact the nearest Bosch Security Systems location or visit www boschsecurity com Bosch Security Systems Installation Manual 2014 10 5 0 F 01U 167 418 8 en System overview UHO Camera Housing 3 System overview 3 1 Available models These outdoor camera housings are available in several versions The variants are input power supply fitted connectors and temperature control All models are equipped with a heater and a sunshield The maximum camera lens size H x W x D for all models is 91 x 81 x 262 mm 3 6 x 3 2 x10 3 in UHO HBGS and UHO HBPS models have a blower fan UHO HGS and UHO HBGS models have feed through holes for power and signal cabling UHO HPS and UHO HBPS models have a 4 pin power connector and a BNC connector instead of feed through holes The following models are availabl
9. ioning The unit should only be passed on together with this installation guide Disposal Your Bosch product was developed and manufactured with high quality material and components that can be recycled and reused This symbol means that electronic and electrical appliances which have reached the end of their working life must be collected and disposed of separately from household waste material ess Separate collecting systems are usually in place for disused electronic and electrical products Please dispose of these units at an environmentally compatible recycling facility per European Directive 2012 19 EU 2014 10 5 0 F 01U 167 418 Installation Manual Bosch Security Systems Bosch Security Systems B V Torenallee 49 5617 BA Eindhoven The Netherlands www boschsecurity com Bosch Security Systems B V 2014
10. ircuit protection must be secured with a maximum fuse rating of 16A This must be in accordance with NEC 800 CEC Section 60 2014 10 5 0 F 01U 167 418 Installation Manual Bosch Security Systems UHO Camera Housing 1 3 Safety en 5 Important safety instructions Read follow and retain for future reference all of the following safety instructions Follow all warnings before operating the unit 1 Clean only with a dry cloth Do not use liquid cleaners or aerosol cleaners 2 Do not install unit near any heat sources such as radiators heaters stoves or other equipment including amplifiers that produce heat Never spill liquid of any kind on the unit Take precautions to protect the unit from power and lightning surges Adjust only those controls specified in the operating instructions Operate the unit only from the type of power source indicated on the label Unless qualified do not attempt to service a damaged unit yourself Refer all servicing to qualified service personnel 8 Install in accordance with the manufacturer s instructions in accordance with applicable local codes So RW 9 Use only attachments accessories specified by the manufacturer Power disconnect Units have power supplied whenever the power cord is inserted into the power source The power cord is the main power disconnect for all units All pole power switch Incorporate an all pole power switch with a contact separation of
11. nal block Strip no less than 6 mm 0 25 in and no more than 8 mm 0 31 in of insulation away from the power supply wires Do not nick the wires Connect the camera power cord wires to the 120VAC OUT or 230VAC OUT connections 4 of the terminal block 2014 10 5 0 F 01U 167 418 Installation Manual Bosch Security Systems UHO Camera Housing 6 3 6 3 1 6 3 2 Connection en 19 Housings with rear connectors Connection UHO Rear housing video connection A BNC connector is provided on the rear of the housing Connect the analog video cable to this connector Connection UHO Rear housing power connection The housings with the rear connectors already mounted are supplied with a 4 pin cable connector for the power cable The 230 VAC models have a male panel connector A female cable connector is provided The 24 VAC models have a female panel connector A male cable connector is provided Mount the 4 pin cable connector onto the power cable 1 Cable diameter must be between 6 mm 0 24 in and 12 mm 0 47 in 2 Strip no less than 6 mm 0 24 in and no more than 8 mm 0 32 in of insulation away from the wire Do not nick the wires 3 Insert the power cord through the back shell assembly and strain relief 4 The cable connector terminals accept wire ranging from 0 75 mm to 2 5 mm 18 AWG to 14 AWG 5 Connect the power input wires to the numbered screw terminals on the mating connector according
12. rd approximately 5 mm 0 2 in from the front of the window 4 Tighten the two screws to lock the tray in place Bosch Security Systems Installation Manual 2014 10 5 0 F 01U 167 418 16 en Connection UHO Camera Housing Connection Feed through power connection Caution To protect the device the branch circuit protection must be secured with a maximum fuse rating of 16A This must be in accordance with NEC 800 CEC Section 60 Caution The external ground wire must always be connected to the main ground post inside the housing 6 1 1 Incoming power safety earth connection Connect the incoming power safety earth wire to the grounding post on the PCB bracket assembly as follows 1 A terminal lug 4 is provided for connecting the incoming power safety earth wire 2 Remove the nut the washers and the ground wire lug from the grounding post 5 3 Strip the incoming power safety earth wire and crimp into the lug 4 Reattach the ground connections in the order shown 1 Nut 2 Lock washer 3 Flat washer 4 Input power ground lug 5 Grounding post 2014 10 5 0 F 01U 167 418 Installation Manual Bosch Security Systems UHO Camera Housing 6 1 2 Connection en 17 Incoming power wires The terminal block accepts wire ranging from 0 5 mm to 2 5 mm 20 AWG to 14 AWG When using larger wire sizes splice to a smaller size wire at the terminal block end The
13. received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules and ICES 003 of Industry Canada These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and radiates radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his expense Intentional or unintentional modifications not expressly approved by the party responsible for compliance shall not be made Any such modifications could void the user s authority to operate the equipment If necessary the user should consult the dealer or an experienced radio television technician for corrective action The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington DC 20402 Stock No 004 000 00345 4 2014 10 5 0 F 01U 167 418 Installation Manual Bosch Security Systems UHO Camera Hous
14. splice may need to be enclosed in a junction box if it does not pass through the fittings 1 Strip no less than 6 mm 0 25 in and no more than 8 mm 0 31 in of insulation away from the power supply wires Do not nick the wires 2 Connect the incoming power wires to the AC input connectors 3 on the terminal block as shown in the following figure GL O i oO SS SS L N G L N x ee a EN ea AC INPUT AC OUT DC12v OUT O IL 6 Callout Function 1 Power cable input to housing G green yellow Earth wire L brown power wire N blue power wire 2 Power input grounding post 3 AC power input terminal block connectors 4 AC power output to camera 5 12 VDC power output to camera 6 Fuse Bosch Security Systems Installation Manual 2014 10 5 0 F 01U 167 418 18 en Connection UHO Camera Housing 6 2 Camera connections 6 2 1 Camera video connections Connect the video and data cable directly to the camera 6 2 2 Camera power connections Connect power to the camera as follows refer to wiring diagram For 12 VDC cameras Connect the DC12V OUT connections on the terminal block 5 to the 12 VDC inputs of the camera For 24 VAC cameras Connect the 24VAC OUT connections on the terminal block 4 to the 24 VAC inputs of the camera For 120 VAC and 230 VAC cameras Cut the power cord coming from the camera making sure that there is enough left to reach the termi
15. to the table Connector terminal number Function Wire color 1 AC neutral Blue 2 AC live Brown 3 No Connection do not use 4 Ground Green yellow 6 Assemble the cable connector and plug it into the power receptacle on the housing Bosch Security Systems Installation Manual 2014 10 5 0 F 01U 167 418 20 en Connection UHO Camera Housing 6 4 Final assembly 6 4 1 Camera operation Warning Hazardous voltage Use caution when working inside the housing Hazardous voltage is present in the housing when connected to the AC supply Do not touch the power terminals when the unit is powered Verify operation of the camera and lens before final assembly Adjust the camera orientation focal length if applicable and focus as necessary refer to the camera installation manual 6 4 2 Closing the housing Caution Always securely tighten all fittings to ensure a liquid tight seal Failure to do so could allow water to enter the housing and damage the units If a sealant is used ensure that it is a neutral cure type Sealants that release acetic acid may harm electronics Use drip loops on the wiring outside the housing Pull any excess wire out of the housing and tighten the cable glands The tightening force required is approximately 1 to 1 5 turns past the point where the gland starts to grip the wire Failure to correctly tighten the glands could result in water ingress
16. urity Systems UHO Camera Housing 5 4 5 4 1 5 4 2 5 4 3 Installation en 13 Feed through cables Feed through power cables Power into the housings must be supplied using type UL Standard SJ cord or better acceptable for outdoor use Installation must conform to NEC 400 4 CEC rule 4 010 and be marked with OUTDOOR W or W A The supplied cable glands have the following specifications Gland type Cable clamping range 3 8 in NPT 4 5 to 7 9mm 1 2 in NPT 5 8 to 10 mm M20x1 5 3 5 to 8 mm Feed through wiring through the base To feed cabling through the base of the housing 1 Remove the two dome plugs located at the bottom the housing Screw the two 3 8 in NPT fittings into the foot of the housing Attach the foot of the housing to the mount Feed the power and video cables through separate cable glands into the housing ol tS Ensure that the holes in the rear are covered with the rubber plugs provided Feed through wiring through the rear The rear holes allow cable to be fed through the supplied glands or the direct connection of conduit fittings 1 Remove the dome plugs located at the rear the housing 2 Screw the cable glands into the holes at the rear of the housing The holes accept either 3 8 in NPT or 1 2 in NPT cable glands or conduit fittings The M20 x 1 5 cable gland can also be used 3 Feed the power and video cables through separate cable glands into the ho
17. using 4 Ensure that the holes in the bottom of the housing are covered with the rubber plugs provided Bosch Security Systems Installation Manual 2014 10 5 0 F 01U 167 418 14 en Installation UHO Camera Housing 5 5 Camera Lens installation 5 5 1 Camera tray mount 1 Loosen the two screws holding the camera tray in the housing Slide the tray backwards and remove from the housing 2 Attach the lens to the camera If the lens length can vary make sure that it is fully extended 3 Use the 1 4 20 x 3 8 in screw the flat washer and the steel camera clamp to secure the camera to the camera tray By 1 420 x 3 8 in Low profile cameras For low profile camera lens assemblies use different combinations of the 9 mm and the 4 mm plastic spacers to ensure that the camera lens is in the center of the window With the spacers use the 1 4 20 x 3 4 in screw the spring washer and plastic clamp or second spacer as necessary to attach the camera lens to the camera tray 5 1 4 20 x 3 4 in 2014 10 5 0 F 01U 167 418 Installation Manual Bosch Security Systems UHO Camera Housing Installation en 15 5 5 2 Mounting the camera tray in the housing 1 Slightly tilt the camera lens tray assembly and slide it in under the rail that is located under the heater on the right side of the housing 2 Lower the tray so that the holes at the side fit over the two screws of the housing 3 Slide the entire assembly forwa
Download Pdf Manuals
Related Search