USER'S MANUAL
Contents
1. INTERNET NEMA5 15R INSTALLATION AND OPERATION Upon receipt of the UPS inspect the shipping carton for damage If there is any obvious damage immediately report it to the selling dealer or the delivering carrier If there is no damage to the shipping carton unpack the unit and inspect the unit for damage The UPS is designed for installation in a protected environment within a temperature range from 32 F to 104 F and relative humidity of 0 90 without condensation Do not block inlets and outlets Install the system in a location free from excessive dust and chemical fumes Check the identification label to verify the UPS voltage and power rating match the available line voltage and load requirements Installation 1 Check if the main switch on the UPS front panel is in the off position and insure that the voltage of the AC utility source corresponds to the nameplate on the UPS rear panel 2 Plug the power cable into the grounded socket 3 Push the main switch then the Load Level LCD will light on for 2 seconds and CUT OFF LCD will light off The UPS will then get ready and start to work normally 4 Connect your PC with UPS then turn on PC Be sure to check the Load Level LCD indicator and DO NOT OVERLOAD it over 100 To simulate AC failure You may disconnect the power cord of the UPS2. is converted by AC DC CHA and support charging power to charge dl N F Fig 2 shows how the UPS works when AC Utility normal OUTPUT COMPUTER INTERFACE The computer interface DB9 port on the back of the UPS may be connected to a host computer This port allows the computer to monitor the status of the UPS and control the operation of the UPS Pin out information PIN Description 1 0 PIN1 Battery low normally open active close Output PIN2 N C PIN3 Common Ground PIN4 Remote shut down keep this pin high Input 5 12V for 3S will turn off the UPS PINS N C PIN6 N C PIN7 Must keep in high state Input PIN8 Line fail normally open active close Output PINS N C D SUB 9 Pin Female Connector 1 Low Battery IN 2 8 Mains Failure o o j 3 O 7 Contacts Normally Open UPS Shut Down Signal High Min 3 Second Pin Number OVERVIEW Front Panel 1 Master Power Switch Turn on off the UPS 2 LINE ON AC Normal 3 AVR Protection LCD When AVR is working under protection mode the light will turn on 4 BACK UP Battery in back up 5 Over Load If the UPS is overloaded the light will turn on and the alarm will sound continuously 6 UPS Cut off Overload or Cut off 7 Battery Level A bar graph showing how much of the UPS battery is being used 8 Load Level A bar graph showing how much of the UPS power is being used Re
3. N A D i L 7 N 7 Emergency Backup Power Supply For Use With Computer Loads Only gt Power Surge Noise Protection Intelligent Auto Shutdown Software J 7 NE Internet Line Protection gt FEN E Compact 8 Reliable Design gt lt ael U el oO 2 o 5 USER S MANUAL lt gt He N 1 Edition Uninterruptible Power System IP 021 a3 02 IMPORTANT SAFETY INSTRUCTIONS Thank you for selecting this uninterruptible power system UPS It provides you with better protection for connected equipment Please read this manual This manual provides safety installation and operating instructions than will help you derive the fullest performance and service life that the UPS has to offer Please save this manual It includes important instructions for the safe use of this UPS and for obtaining factory service should the proper operation of the UPS come into question Please save or recycle the packaging materials The UPS s shipping materials were designing with great care to provide protection from transportation related damage There materials are invaluable if you ever have to return the UPS for service Damage sustained during transit is not covered under the warranty NOTES CAUTION The UPS contains voltage that are potentially hazardous All repairs should be performed
4. ar Panel 1 Input IEC type connector to connect the power cable 2 AC Fuse Protection against short circuits electronic fuse 3 Data line protection Filtering of electrical noise on data transmission lines 4 Communication port Basic communications 5 AC Battery outputs Output protected for critical loads that require additional electrical power 6 UPS function setup No load auto shut down Dc start On and Buzzer Alarm auto reset Picture 0 25 50 75 100 Front Panel CONTENTS PAGE Te CAUTION een are ea a 1 2 INTRODUCTION SYSTEM DESCRIPTION us ee ar 2 FEATURES Hanau 2 3 SYSTEM CONCEPT BLOCK DIAGRAM 2 22m 3 NORMAL OPERATION 3 AG UTILITY FAILURE anne 4 4 OVERVIEW FRONT PANEG a seien 5 REAL PANEL iii dai 5 PIGTUR E 0 aa a aa ae 5 5 INSTALLATION AND OPERATION 7 6 COMPUTER INTERFACE eee 8 7 BATTERY URAC TS 2er ee E 9 8 SPECIFICATIONS En idas 10 9 TROUBLE SHOOTING usa are 11 10 NOTES nenne 12 INTRODUCTION System Description The product is line interactive UPS with the newest technology and powerful function The Line Interactive UPS is with AVR function allows input voltage range from 75 to 125 including on line voltage boost up amp buck down An ideal protection equipment for critical connected loads In addition This UPS provides advanced single telephone li
5. by qualified service personal The UPS has its own internal energy source battery The output receptacles may be alive even when the UPS is not connected to an AC supply The UPS is suitable for computers and electronic equipment with substantially rectifier or capacitive loads not suitable for electronic equipment with significant inductive loads such as motors amp fluorescent lamps Be sure to operate within the power rating of the UPS Below 1 2 or 1 3 of rated power is recommended for longer backup time amp longer battery life Do not place the UPS near excessive humidity under sunshine or close to heat emitting sources If the UPS is out of order please detach power cord and consult your dealer right away Do not remove cover if there is no serviceable part inside The unit should be supplied by grounded source Do not operate the unit without ground source The socket outlet should be installed near the equipment and be easily accessible Do not plug the UPS power cord into itself That will result in a safety hazard Installation should be performed by a qualified technician or electrician in accordance with local electrical codes SPECIFICATIONS Capacity VA 400VA 500VA 600VA 800VA 1000VA 100VAC 110VAC 120VAC 220VAC 230VAC or 240VAC Voltage Input 125 Frequency 50Hz or 60Hz 15 100VAC 110VAC 120VAC 220VAC 230VAC or 240VAC Voltage Batt M
6. e of purchase 3 Full description of the problem including load LED and alarm status installation condition working environment etc Trouble Shooting Chart Caution To Take Problem Possible Cause Front panel switch Turn on switch in off position No light and no alarm Rear panel fuse UPS not on Replace fuse restart UPS burnout Power cord lose Check input power No Line on LCD Power cord lose Check input power light and alarm beeps Replace fuse if problem AC Fuse burnout every few seconds remains call for service Recharge the battery for at Backup time is less Battery is not fully least 6 hours re test the than the rating charger failure backup time If problem remains call for service Feature available on 800VA and up models 3 AC Utility Failure If AC utility fails the UPS quickly detects the problem and activates the inverter The inverter The DC AC inverter changes DC power from the batteries into AC and provides continuous uninterruptible power to load Fig 3 shows how the UPS works when AC Utility Failure BATTERY FACTS The battery is the only periodically serviceable parts in the UPS An expected life is approx 3 5 years However frequent long discharges or ambient temperatures above 80 F will shorten battery life Therefore it is recommended to replace the batteries every 3 years after
7. from wall outlet can help to insure whether UPS is in good condition or not It is designed to alarm every 3 seconds and with BACK UP LCD light on when simulation starts If the CUT OFF LCD is on it means UPS fault or BATTERY fault Then you have to contact your local service center 5 When battery approaches low level alarm will beep every second until auto shut down 6 The 4 conditions UPS will automatically shut down a Battery low b Short circuit c Overload d UPS fault fe 2 a 4 5 Hee 7 8 Qe 10 11 12 13
8. initiating the unit Recharge batteries every 3 months is necessary if it is not in use because it may cause batteries over drain WARNING Only a qualified technician should replace the battery Batteries have high short circuit current capacity mistakes in connecting or disconnecting can cause connections to arc or weld and could cause severe burns STORAGE The UPS should only be stored if the battery is fully charged Avoid storage temperatures above 80 F as battery life is significantly shortened Every 90 days remove the unit from storage and plug it in for 24 hours to recharge the batteries Batteries may be damaged if left in storage and not recharge every 90 days IMPORTANT NOTICE Please use same type and same rating of batteries for replacement Do not replace it with the battery that exceeds specified rating Picture 00000 321 OWLS O HN REMOTE AC BATTERY OUTPUTS INTERNET AC INPUT IEC 320 00000 0000 REMOTE 321 is AC BATTERY OUTPUTS 00000 321 0 0 dm REMOTE AC BATTERY OUTPUTS E U rn INTERNET INTERNET REMOTE SITO int AC BATTERY OUTPUTS
9. ne or modem surge suppression through the modular connectors on the back panel The Line Interactive UPS and RUPS2000 monitoring software Optional kits makes our computer operate intelligent and provides you with the ability of perfect protection of your critical devices Features Line interactive design User friendly LCD display Provide boost and buck AVR to stabilize input voltage Provides lightning surge overload and short circuit protection Built in CCCV battery charger and battery over drain protection No load auto shutdown Dip switch setup Load level and Battery level display Buzzer alarm auto reset Dip switch setup Auto restart when AC recovery Cold start function Dip switch setup VV Y Y Y Y Y Y Y NV V Tel Modem Fax Internet surge suppression Y Option Bundle software Automatically save your valuable files before auto shutdown TROUBLE SHOOTING If the UPS failed to operate properly please review the following checks firstly If the problem remain please consult sales agent for service Is the Master power switched on Is the UPS plugged into a correctly working outlet Is the line voltage within the rating specified Is the fuse on the rear panel blown Is the UPS over loaded Is battery not fully charged Dead battery Charger failure Please provide the following information when call for service 1 Model number serial number 2 Date of the problem occurred dat
10. ode 10 Output Frequency 50Hz or 60Hz 1Hz Waveform Modified sine wave Transfer Time Less than 4ms typical Sealed maintenance free lead acid batteries with 3 5 Battery Type Battery years typical lifetime Recharge Time 5 hours to 90 of full capacity LCD indicator for line on battery back up AVR protection Indicator LCD Overload and cut off Load and battery level Battery Back up Sounding every 3 seconds Alarm Battery Low Sounding every 1 second Overload Continue beeping sound Overload Fuse amp current limited Protection Short Circuit Fuse amp current limited amp cut off Batt Low Cut off No battery drain after cut off Physical Dimension D W H 270 94 170 mm 385 94 170 mm Environment Operating Temperature 32 F 104 F at full load 0 90 relative humidity non condensing Noise Level Less than 40db at 1 meter Interface Contact Closure DB9 connector for connecting with Rups 2000 software Software Rups 2000 Option 1 Block Diagram SYSTEM CONCEPT The purpose to present this chapter is to give you more precise conception about how UPS works OUTPUT de 2 Normal Operation There are two main loops when AC Utility normal the AC output loop and the Fig 1 shows how UPS works battery charging loop The AC output gets power from AC utility input and pass through AVR to support power to load In the same time the AC utility input
Download Pdf Manuals
Related Search