User Manual
Contents
1. Possible Cause 2 The connection between the light unit and the pentagular Pentagular Mobile Cart cart might be off Please check their connection status as shown on the right picture 13 Possible Cause 3 The power is off please connect the plug back to the wall power socket or make sure that the electricity is coming out of the socket before plugging in Possible Cause 4 If the cause 3 does not fit to the scenario a doubt of the built in adaptor is broken Please send the unit back to your local dealer for repair 2 Why can I not fix the adjusted angle of the light unit Important TEN The active angle suitable for the weight of our light unit is 60 vertical angle see right pic Please maintain the working angle within this range Possible Cause 1 There are two knobs on each side of the lamp unit Only 1 of either knob is needed to be secured to enable the locking mechanism to work If both knobs are secured the locking mechanism will fail Possible Cause 2 If the root cause of above can not be determined please send the unit back to your nearest local dealer for re adjustment Thank you 14 3 Why can I not operate the lamp when pressing the power button Possible Cause If the power cord has plugged into the Wall Plug but the Power button does yf ver Wes still not turn to green indicator stand by mode please check for the power of the wall plug and Mote gh replug t2. QMONITEX www monitex com tw WhitenMAX Brsoo Professional teeth whitening unit T i o ra User Manual Table of Contents Preface 1 Disclaimer 1 Safety Precautions 2 Product Parts 3 Assembly nnn nnn nnn neem nnn nnn nn 3 Operation 10 Trouble Shooting Tips 13 Specification 17 Preface Thank you for choosing Monitex Product for your advance integration Prior to using Monitex WhitenMAX BR800 Professional Whitening Unit please read this User Manual carefully and keep this manual well preserved for future reference Please contact your local dealer if any damage or problem occurs Attempt to try and repair this unit by unauthorized technician personnel WILL automatically lead to the forfeit and negation of the warranty agreement The specification are subject to change and revision without prior notice Disclaimer Monitex shall not assume any responsibility if any malfunction or damage was caused by improper operation removal modification or maintenance We shall not assume any responsibility if any malfu
3. a hard stain then please use a neutral cleaning agent for removal Important Never use a solvent or volatile oil for cleaning This can lead to fading in the paint or display board Special Symbols Symbol Explanation Type B applied part A Attention consult i ACCOMPANYING DOCUMENTS CE Signifies the device has met all essential requirements of European Medical Device Directive 93 42 EEC O C Symbol used to indicate the polarity of the DC power input Ded Direct Current Product Parts Packaging A Pentagular Mobile Cart B N shape Iron Stand C Operating Panel D Rotating Arm E Light Unit and Mouth Piece F Localized Plug Adaptor Europe Plug built in and us plug on option please see page 9 G Iron Rim H Plastic Washer Rim Protective Glasses Assembly amp Dis assembly Caution Please always space the site for your precaution before executing your installation as some of the iron made parts can be damaged of its paint or damaging to other equipment if it s handled improperly A Pentagular Mobile Cart Place Mobile Cart in an open space for preparation of assembly B Assembly of N shape Iron Stand amp Pentagular Mobile Cart gt Take out the N Shape Iron Stand for preparation of installing onto the Pentagular Mobile Cart gt Place the Iron Rim onto the bottom of the N Shape Iron Stand gt Place the Plastic Washer Rim inside the rim for secure purp
4. Power Output Power Button LED Dual Color Display Green Standby Mode Orange Push the power button to enter Operation mode r Mode 1 Mode2 100 Full Power Output ppe BSR Rd C E e Light Source Selection CK ED C H R Ajustable Whitening Timer TIME Adjustable up to 1 20 Minutes Adjusting interval 1 minute per push TIME Start amp Stop Button Blue emits Medical use LED Cool Blue light Red emits Red light to Accelerate the bleaching process B amp R signifies Blue amp Red Light turns on Simultaneously PS There are a total of 4 x 3W Blue Led bulb amp 1x 3W Red Led bulb built in One press START STOP initiates the operation The following press terminates the operation P S BR800 enters Stand by Mode when in idled for more than 1 minute 12 Trouble Shooting amp FAQ 1 LED malfunctions What happens if the Blue or Red LED does not work Possible Cause BR800 Blue LED are connected in serial manner Blue LEDs are connected together and Red LED is connected individually If one of the Blue LED does not work all four will cease function while the Red LED remain functioning individually Solution Please send BR800 back to the supplier for repair What happens if none of the LED work Possible Cause 1 The connection between the light unit and the display panel might be off Please check for their connection status as ref to pictures below
5. Voltage AC 100 240V 50 60HZ Power 19 W Weight 9 4 kgs net Dimensions on Total Arm Length 960 mm Total Height 1245 mm 17 RAONITEX inoustriat CO LTD 6F 70 SEC 1 GUANG FU ROAD SAN CHONG CITY 24158 TAIPEI COUNTY TAIWAN TEL 886 2 29993869 FAX 886 2 29993647 E mail monitex monitex com tw http www monitex com tw
6. he Display Panel is If the power plug in the wall is normal please send the unit back to your nearest dealer for examination 4 Why is that my Display Panel or the buttons do not work Possible Cause If by checking after all connection and plugging in to the Wall Plug the display panel still does not function please check for the power of the wall plug and replug the Display Panel qo If the wall plug is normal please send the unit back to your nearest dealer for examination 5 Unable to ultilize Pentagular Push Cart freely Please check if the Lock Switch are all released amp the handle lifting upwards 15 6 Abnormal Burning smell occurs A Check from where the Burning smell lt gt 4 If the smell is coming from the machine Please send back to your nearest dealer for examination Thank you A 4 A 7 Why was my BR800 overheated within operation of less than 20 minutes Possible Cause Listen to the sound of the built in motor fan This fan should be normally activated when the temperature reaches 40 C If the fan motor does not function the thermo sensor will indicate Overheating sign to shut off BR800 for protection Most likely to be taken within 20 minutes Please send the unit back to the dealer for further checking and repair 16 Specification Light Source 4 3W Blue leds amp 1 3W Red led Output Spectrum 450 470 nm amp 620 630 nm
7. nction or damage was caused by operating under unsuited environment We shall not assume any responsibility if any malfunction or damage was caused by forceful majeure We reserve the right to explain for the given cause of the Defective products which might have been caused by natural disasters or abnormal temperature humidity that is inconcurrent to the guidance instructed in this manual Safety Precaution Please follow instruction steps in this manual for correct and safe operations of the device Pay more attention to the following four warning signs beside the operation descriptions where applicable Danger This message appears where the operation may potentially cause severe injury if instruction not followed correctly Warning This message appears where the operation may cause serious damage or defect to other objects Caution This message appears where the operation may cause slight damage to other objects or slight bodily harm if operation not properly conducted Important This message appears where the operation may involve risk of defecting the device itself if not properly conducted Transport and storage Environment conditions Temperature 20 C to 65 C 4 F to 149 F Humidity 15 90 non condensing Maintenance If there is any dirt or stains on the surface of control panel metal parts or mouth piece please use dried cloth with Medical use Alcohol to gently wipe clean If there is
8. ose s gt Pull out the plug from inside the N shape Iron Stand and connect the plug onto the jack pre installed inside the Pentagular Mobile Cart C Assembly of N Shape Iron Stand amp the Rotating Arm gt Place the Rotating Arm in the open area for preparing installation gt Please repeat the procedure stated previously by inserting the Silver Iron Rim and the Plastic Washer Rim onto the top of the N Shape Iron Stand to receive clockwise turning for secure screw lock gt Plug in the Power Cable and the Connecting cable between Light Unit and the Display Panel check and make sure all connection fixed well Plug in the Power Cable to the Display Panel Plug in Connecting Cable between Light Unit amp the Display Panel gt Plug in the extended Connecting Cable from the Rotating Arm to the extended plug located in the top of the N Shape Iron Stand to complete the connection between the Display Panel amp the Light Unit iby a D Assembly of the Rotating Arm amp the Light Unit gt Please prepare the Light Unit with protect Mouth Piece for installation gt Make sure the Mouth Piece is properly placed onto the Light Unit Caution Please make sure always to disinfect the Light Unit and Mouth Piece with medical use alcohol before carrying any operation gt Follow the instruction illustrated below by placing the Iron Rim and the Plastic Washer Rim to secure the light
9. r transportation or sent for repair and it s requested to reverse carefully the above procedures and store the parts in the original packaging material for delivery and or storage 9 Operation Functional Introduction Please see below diagram and description for instruction of use MONITEX WhitenMAX BR800 Blue B amp R Red mgg Sec AAONITEX BR 800 Monitor Gop B amp R Red Control Panel Danger Please do not look directly into the lights nor acquiring the emitting light directly onto patient Such action can cause a danger or harm to patients eyes 10 Monitor Timer l MONITEX The timer first starts count down Selection of WhitenMAX BR800 upon push Start Stop button Light Source Blue B amp R Red Coit The Min indicate the number ict f Nimaa of minutes currently remain of c AAONITEX BR 800 The Sec indicate the last minute of count down Pre Set Time is 10 Minutes l Indication of your POEN Mode Selection High Mode 1 Low Mode 2 Over Heat Indicator When the temperature reaches 40 C it automatically activate fan motor for heat dissipating Important When the temperature reaches 70 C as our protection mechanism the build in Thermometers will start to blink on the drop while the unit ceases functioning till the temperature climb down 11 Control Panel Two Flux Modes Illumination Mode 1 High Mode 2 Low 70
10. unit onto the Rotating Arm gt Turn the Iron Rim by clockwise to fix the support of Light Unit Important Please make sure to position the Light Unit tightly amp securely to prevent Light Unit from falling off or cause unnecessary damage Plug in Make sure to plug in the Light Unit from the cable extended from the Rotating Arm WARNING Beware of high temperature and strong light Do not look directly into the light source if without using any eye protection WARNING Light unit is a heat generating source The temperature might reach to 65 for long term usage Beware of high temperature 8 Wheels Congratulation You have successfully assembled your BR 800 WhitenMAX LED Bleaching Light Unit Important There are 3 handle locks located in 3 of the 5 wheels under the Mobile Cart After safely placing BR 800 to your appointed location or chair side please press down the handle locks to secure your unit and prevent BR 800 from mobility To set it free for mobile simply unlock it by lifting the handle lock in accordance to the following picture Power Plug Each BR 800 is built in with a 100 240V Power adaptor inside of the Pentagular Mobile Cart The preset extension cord is European Plug Additional power plug adaptor is available on request as optional accessories Please store the packaging materials safely for future use Perchance if the unit is required to be disassembled fo
Download Pdf Manuals
Related Search