Home

Datalogic Memor™ User's Manual

1. DATALOGIC Datalogic Memor ODATALOGIC meamor User s Manual O SDATALOGIC Datalogic Mobile S r l Via S Vitalino 13 40012 Lippo di Calderara di Reno Bologna Italy Datalogic Memor User s Manual Software Version 4 00 Ed 05 2009 ALL RIGHTS RESERVED The Datalogic name and logo are registered trademarks of Datalogic S p A in many countries The Memor name is a trademark of Datalogic Mobile S r l All other brand and product names mentioned herein are for identification purposes only and may be trademarks or registered trademarks of their respective owners Datalogic reserves the right to make modifications and improvements without prior notification Datalogic shall not be liable for technical or editorial errors or omissions contained herein nor for incidental or consequential damages resulting from the use of this material 2008 2009 Datalogic Mobile S r l All rights reserved Protected to the fullest extent under U S and international laws Copying or altering of this document is prohibited without express written consent from Datalogic Mobile S r l CONTENTS ch A AA bo bo bh o bh gh SHEET REFERENCES o v elen e vV Reference Documentation V Services and SUPPO diia dd a V SAFETY REGULATIONS ri vi General Salety Rules eli dille vi Gelee EE vi CASA e vii E E xiii Radio Compliance annali aa xiii PCG COMplanCO asa Ee XV SAR
2. NICHT DIREKT MIT OPTISCHEN INSTRUMENTEN BETRACHTEN GERATEKLASSE 1M RADIO COMPLIANCE In radio systems configured with mobile computers and access points the frequencies to be used must be allowed by the spectrum authorities of the specific country in which the installation takes place Be absolutely sure that the system frequencies are correctly set to be compliant with the spectrum requirements of the country The Radio modules used in this product automatically adapt to the frequencies set by the system and do not require any parameter settings The following shows the correspondence between the Datalogic Memor models and the Radio components DL Memor 802 11g BT models 802 11b g and BT radio modules C 0678O DL Memor EdgeE BT models GSM GPRS EDGE and BT radio modules C 0678 xiii Information for the User ENGLISH Contact the competent authority responsible for the management of radio frequency devices of your country to verify any possible restrictions or licenses required Refer to the web site http europa eu int comm enterprise rtte spectr htm for further information ITALIANO Prendi contatto con l autorit competente per la gestione degli apparati a radio frequenza del tuo paese per verificare eventuali restrizioni o licenze Ulteriori informazioni sono disponibili sul sito http europa eu int comm enterprise rtte spectr htm FRANCAIS Contactez l autorit comp tente en la gest
3. USE AND FUNCTIONING a 3 7 4 Wireless Communications The WIRELESS COMMUNICATIONS applet provides management of the 802 11b g radio the Bluetooth and GSM modules Windows CE Wireless Communications Windows Mobile Connectivity Icon Icon If the mobile computer supports Windows CE select the WIRELESS COMMUNICATIONS applet by double tapping the Wireless Communications icon The following window will appear Wireless Communication BlueTooth Off Wi Fi Je GSM GPRS E Wireless Communications Window If the mobile computer supports Windows Mobile the Wireless Manager application manages access to wireless connections The Wireless Manager is a sort of Control Panel for bluetooth and phone modules From here it s possible to turn on or off bluetooth and phone radio stacks Open the Wireless Manager by tapping Start gt Settings gt Connections gt Wireless Manager or by tapping the Connectivity icon located at the top of the screen The following window will appear 51 ED DATALOGIC MEMOR Wireless Manager Es Te X Network Card D I Off een R Done Menu Windows Mobile Wireless Communications Window 52 USE AND FUNCTIONING a 3 7 5 Stylus Calibration You might need to recalibrate the touch screen i e when you attempt to select one item with the stylus another item is erroneously selected To recalibrate the touch screen on Windows CE complete t
4. bk al 6 Close the battery cover properly by pressing the latch release button and pulling the latch down To remove the Micro SD card follow the steps above to access the SD area and remove it from its slot Follow proper ESD precautions to avoid damaging the SD Proper ESD precautions include but are not limited to working on an ESD mat and ensuring that the operator is properly grounded CAUTION Po not force the card If you feel resistance remove the cara check the orientation and reinsert it Do not use the Micro SD card slot for any other accessories INTRODUCTION Sp 1 5 INSTALLING THE SIM CARD To correctly insert the SIM Card proceed as follows 1 Turn off the Datalogic Memor 2 Press the latch release button and pull the latch down as indicated in the figure below 3 Remove the cover and the battery pack then open the SIM card slot by pulling up the locking plate Db DATALOGIC MEMOR 4 Shift the cardholder to the left and then pull it up insert the SIM Card with its contacts downward and its round corner at the bottom 5 Lock the card into place by pushing the cardholder down and then shifting it to the right 6 Pull the locking plate down 7 Close the battery cover properly by pressing the latch release button and pulling the latch down Follow proper ESD precautions to avoid damaging the SIM card Proper ESD precautions include but are not limited to
5. depending on model 250 g 8 81 oz incl 2000 mAH battery Programming Features Operating system Windows CE 5 0 Professional Windows Mobile 6 1 Professional Decoded barcodes 1D UPC A UPC E EAN 8 EAN 13 Code 39 Code 39 Full ASCII Code 32 Interleaved 2 of 5 Industrial 2 of 5 Matrix 2 of 5 Code 128 EAN 128 Codabar MSI Plessey Code 93 Code 11 GS1 Databar Decoded barcodes 1D UPC A UPC E EAN 8 EAN 13 UPC EAN JAN Interleaved 2 of 5 Code 39 Code 39 Full ASCII Codabar Code 128 EAN 128 Code 93 GS1 Databar Decoded barcodes 2D PDF417 DataMatrix QR MacroPDF RSS Postal codes POSTNET PLANET Japan Post Australia Post KIX Code Royal Mail Code RM4SCC 82 TECHNICAL FEATURES ED Datalogic Memor Optical Features Maximum resolution Skew angle Pitch angle Scan rate bidirectional Light source laser scanner Safety class Laser Class 2 EN 60825 1 2001 Led Green Spot Class 1 Datalogic Memor 2D Models Maximum resolution 0 13 mm 5 mils Scan rate 60 frames sec Aiming Laser VLD wavelength 645 665 nm Safety class Laser Class 2 EN 60825 1 2001 Led Illuminator Class 1M Illumination System LEDs 620 630 nm 83 DATALOGIC MEMOR READING DIAGRAM 5 2 Datalogic Memor 1D Typical Reading Diagram Reading Zones 10 skew angle OQ PE 1 DES I l I I I l I I I I I I I 1 1 1 I l I 1 1 I I I RIO ES D A ETS See e EE Dee gece 57y J I I I I I I I 1 1 T I
6. 2 Tap Settings The Settings tab allows you to enable or disable the Bluetooth radio and specify settings for Incoming Connections 3 Select or clear the Enable Bluetooth Radio check box Bluetooth Manager OK x Connections Discovery Settings grescnscesconseesscsncenscsssnecescsecsncensessensseny Incoming Connection Encrypt Incoming Connections T Authenticate PIN Port None y Find Me Apply Info Y ei IM zv AA Tap Find Me if you want to make the Memor visible to other Bluetooth devices for 60 seconds allowing them to set up a connection Bluetooth Manager OK i Connections Discovery Settings V Enable Bluetooth Radio Incoming Connection Discoverable for 60 Seconds Find Me Apply Info ei 0 2 4 A By default Bluetooth is turned off If you turn it on and then turn off your device Bluetooth also turns off When you turn on your device again Bluetooth turns on automatically 62 USE AND FUNCTIONING a To create a Bluetooth partnership between your device and another device that has Bluetooth capabilities ensure that the two devices are turned on discoverable and within close range 1 Open the Bluetooth control panel by tapping Start gt Settings gt Connections tab gt Bluetooth Manager 1 Search for the type of Device s you want to connect to by tapping Printer Serial or All Th
7. Bits are numbered from the right 0 through 7 with bit O the low order bit One byte in memory can be used to store one ASCII character Decode To recognize a bar code symbology e g Codabar Code 128 Code 3 of 9 UPC EAN etc and analyze the content of the bar code scanned EEPROM Electrically Erasable Programmable Read Only Memory An on board non volatile memory chip Flash Disk Non volatile memory for storing application and configuration files 89 GSM Global System for Mobile communication lt is a standard for digital cellular communications currently used in the 900 MHz and 1800 MHz bands Host A computer that serves other mobile computers in a network providing services such as network control database access special programs supervisory programs or programming languages Liquid Crystal Display LCD A display that uses liquid crystal sealed between two glass plates The crystals are excited by precise electrical charges causing them to reflect light outside according to their bias They use little electricity and react relatively quickly They require external light to reflect their information to the user Light Emitting Diode LED A low power electronic light source commonly used as an indicator light It uses less power than an incandescent light bulb but more than a Liquid Crystal Display LCD RAM Random Access Memory Data in RAM can be accessed in random order and quickly written an
8. 2 Version 2 0 WWAN GSM Quad band 850 900 1800 1900 MHz Radio with accessible SIM card interface Environmental Features Working Temperature 0 to 50 C 32 F to 122 F Storage Temperature 20 to 70 C 4 to 158 F Humidity 10 to 80 non condensing for temperatures lt 38 C Protection P 54 ESD Protection 4 KV contact discharge 8 KV air discharge Drop Resistance 1 2m 3ft9 in Battery must be charged at a temperature ranging from 0 to 40 C For the GSM models the maximum recommended temperature is 35 C At higher values the charging may slow down Close to the limits of the working temperature some display and or battery performance degradation may occur Multiple rapid humidity and or temperature variations may cause condensing Multiple drops can permanently damage the device KKK 81 DD DATALOGIC MEMOR FLASH RAM Microprocessor Rear Speaker for beeps and ringing tones Audio Microphone and Front Speaker for phone calls Headset LEDs Two color Good Read Programmable Charging Status Display 64K Color TFT LCD with 320 x 240 pixel resolution QVGA with LED backlight and touch screen antiglare and antiscratch protection Keyboard 23 Plastic Top Backlit Keys Joystick lateral ON OFF key Dimensions LxWxH 802 11b g Batch models 15 2 x 5 5 x 4 0 cm 5 9 x 2 2 x 1 6 in EDGE models 16 5 x 5 5 x 4 0 cm 6 5 x 2 2 x 1 6 in Weight 220 g 7 76 oz incl 1100 mAH battery
9. CGOMPIANCO ani aa xvi PAORS EE xvi WEEE Complicado ici xvii China RoHS Pollution Control LOQOS xix GENERAL ENN eege XX INTRODUCTION weer ica eet aes 1 Datalogic Memor Description AANEREN 1 Models Description ere a E oaa 2 PACKAGE ge 4 Inserting a Micro SD Card EE 5 Installind Beete WEE 7 Removing th SIM Card scialle 9 Lee 10 ODErAlING SYSlSM esses geeebteeueg ege eebe ee AAE ESEE 10 CONNEGTIONS aa 11 EECHER 11 Connection to USB peripherals ccccccccccccccccecececeeeeeeeeeeeeeeeeeeeeees 13 S202 GONNE CIONS aces 15 VT Eet ere EE 16 WRAN COMEN ao 18 AAA 19 Connection Cables ra sla 21 Wireless and Radio Frequencies Warnings 22 USE AND FUNGTIONING i ii 24 RIP 24 Using MS eege bia 26 LISTING the Joys UC cnt do ic 27 Windows Mobile Welcome Ward 28 BER Red 29 Laser Data Capi EE 29 Imager Data Capture cacas ab 30 Description of the EE 32 Resetting the Memor 34 3 5 3 5 1 3 5 2 3 6 1 3 6 2 3 7 1 3 7 2 3 7 3 3 7 4 3 7 9 3 7 6 3 8 1 3 8 2 3 8 3 3 8 4 3 10 4 1 4 3 5 1 5 2 Stats Nd Ca de EE 37 FED GAUS tii E E E E ON 37 E e EE 38 Data Capture Confguration ee reenen rere ee rennene nenene 40 CONO a aaa teases 40 Ee EE 45 Control Panel EE 46 BUON ai ds 47 Regia ili 48 PES ele ul DE 49 Wireless Communicatons i 51 siylus Galibration a ll 53 VOM SeN Six sis sect Geen 56 Windows eet EE 60 Microsoft AcCiivevncb i 60 Bluetoot
10. LASER DI CLASSE 2 LASERKLASSE 2 APPAREIL LASER DE CLASE 2 MASSIMA POTENZA MAXIMALE CLASSE 2 MAXIMA POTENCIA DI USCITA 1 7mW AUSGANGLEISTUNG MAXIMUM PUISSANCE DE SALIDA 1 7mW LUNGHEZZA D ONDA 1 7mw DE SORTIE 1 7mW LONGITUD DE ONDA EMESSA 650nm WELLENLANGE LONGUER D ONDE EMITIDA 650nm CONFORME A EN 650nm EMISE 650nm CONFORME A EN 60825 1 2001 ENTSPR EN 60825 1 CONFORME A EN 60825 1 2001 60825 1 2001 2001 viii ENGLISH The following information is provided to comply with the rules imposed by international authorities and refers to the correct use of your mobile computer STANDARD LASER SAFETY REGULATIONS This product conforms to the applicable requirements of both CDRH 21 CFR 1040 Subchapter J and EN 60825 1 2001 at the date of manufacture For installation use and maintenance it is not necessary to open the device Do not attempt to open or otherwise service any components in the optics cavity Opening or servicing any part of the optics cavity by unauthorized personnel may violate laser safety regulations The optics system is CAUTION a factory only repair item Use of controls or adjustments or performance of procedures other than those specified herein may result in exposure to hazardous visible laser light CAUTION The product utilizes a low power laser diode Although staring directly at the laser beam momentarily causes no known biological damage avoid staring at the beam as one wo
11. Mobile desktop configuration will appear on the screen Wait a few seconds before starting any activity so that the mobile computer completes its startup procedure E Start E Y EE Thursday 11 01 January 0 2003 Phone off E Off Tap here to set owner information SS Mo unread messages Mo tasks Mo upcoming appointments Live Search e Device unlocked Getting Started DATALOGIC el e 0 A Windows CE Desktop Windows MobileToday Screen S Fun ES Contacts Use the stylus par 3 1 1 or joystick par 3 1 2 as suggested to select icons and options The mobile computer goes into power off low power with display and keyboard backlight off when it is no longer used for more than a programmable timeout which is defined in the POWER applet of the Control Panel In this mode it can be awakened resuming operation by the ON OFF key 24 USE AND FUNCTIONING E The mobile computer can also be awakened or turned off by the application program 25 ED DATALOGIC MEMOR 3 1 1 Using the Stylus The stylus selects items and enters information The stylus functions like a mouse Touch the screen once with the stylus to open items and select options Windows Mobile only Tap Touch the screen twice with the stylus to open items and select options Windows CE only Prag Hold the stylus on the screen and drag across the screen to select text and images Drag in a list to select mul
12. adopt the nonpoisonous and harmless environmental protection material to make the part with poisonous harmful substance or the element is all unable to realize the substitution of the poisonous harmful thing or the element because the global technological development level is limited xix GENERAL VIEW A QVGA 64K Color Display G Microphone B Good Read or User H Strap with Stylus Holder Programmable LED I Laser Safety Label C Charging Status LED J Rear Speaker D Speaker K ON OFF Power Key E Scan Key L Product Label under battery F Keyboard M Battery Cover N aa N Data Capture Laser Output P Communication Charger Connector Window through cradle O DC Charger Connector Q Mini USB Communication Connector through cable Remove protective film cover before use XX INTRODUCTION Db 1 INTRODUCTION 1 1 DATALOGIC MEMOR DESCRIPTION The newly updated Datalogic Memor mobile computer maximizes a compact and light weight form factor for ease of use and shirt pocket convenience without compromising durability Feature introductions include the Microsoft Windows Mobile 6 1 operating system an imaging bar code scanner and a GSM radio with Edge All three of these options combine to make the Memor a viable alternative for use in Field Force Automation applications The Edge radio provides a broadband cellular connection for voice and data communication enabling real time transactions and on d
13. dword 00000001 Copy this file to the Datalogic Memor using ActiveSync Launch the reg file from the Datalogic Memor Perform a warm boot on the Datalogic Memor M St i y From the PC gt Explorer address bar or running an FTP Client from the PC enter the Datalogic Memor IP address For more information on FTP Client Server connections refer to the following web page htto msdn2 microsoft com en uS library aa9223 1 6 aspx NOTE 72 USE AND FUNCTIONING ES 3 9 BACKUP DIRECTORY FILE MANAGEMENT All of the Windows CE 5 0 system files reside in RAM volatile memory except for the Backup directory which resides in FLASH non volatile memory Therefore the contents of the Backup directory are persistent even if the mobile computer is re booted or the battery pack is changed You can save your more important files that you don t want to lose due to mobile computer re boot in the Backup directory or create a sub directory within Backup Even though the Windows Directory resides in RAM it often contains files or sub directories created by the user or by installation programs that you don t want to lose at re boot To keep these files persistent it is necessary to copy them to the directory Backup Windows This directory doesn t exist originally only Backup exists and therefore it must be created At the next cold boot before activating the shell Windows CE 5 0 will copy the contents including all sub
14. for different types of service leon Service i O Dialup Networking a File Transfer Protocol FTP Object Exchange OBEX d Object Push OPP Object Exchange OBEX EJ ActiveSync Human Interface Device HID Keyboard Interface Device HID Human Interface Device HID Keyboard Virtual Port allows you to specify the incoming port which is used to communicate serially with an incoming device just as if it were a physical COM port This option is available only if you have selected a Printer or Serial service You can also select Encrypt or Authenticate from the Bluetooth control panel to apply or modify those settings 1 To require Authentication tap the checkbox then tap OK Bluetooth Manager 4 Ty E Bluetooth Manager Create Pairing Name Device 1 Select a service Virtual Port eme i 2 The Authentication Request dialog will then open requesting that you enter a PIN Use the Input Panel to type in the PIN 70 USE AND FUNCTIONING a 43 Ty d Authentication Request ok X Enter a PIN to authenticate the connection Name Device 1 Address 00 02 72 10 D6 BF 3 Tap OK to complete The dialog will also appear when an Authentication request is received from another device Once you have set up a Pairing you can view the settings by double tapping its name from the Connections tab Tap the arrow to change the Virtual Port or Delete to remove the device pa
15. lighted band emitted by the laser must completely intercept the barcode as shown in the figure below NO vum ill III OK LI RI TT ag H III MI Thin If the scan has taken place correctly the Good Read LED gets constant Green for a configurable time if enabled the GoodReadSound emits an acoustic signal if enabled the GreenSpot projects a green spot onto the bar code image Remove the protective film cover over the Laser Output Window before use 29 ED DATALOGIC MEMOR 3 3 2 Imager Data Capture The Datalogic Memor Imager captures a picture of the entire bar code The omni directional scanning does not require that the operator orient the bar code to align with the scan pattern To read a 1D or 2D code simply point the Datalogic Memor Imager model onto the code and press the SCAN Key The Datalogic Memor Imager uses an intelligent aiming system pattern similar to those on cameras indicating the field of view which should be positioned over the code Aiming System If the aiming system pattern is centered over the entire symbology as shown in the following figure either wait for the timeout or release the Scan key to capture the image A red beam illuminates the code which is captured and decoded You will get a good read 30 USE AND FUNCTIONING a Linear barcode 2D Matrix symbol Relative Size and Location of Aiming System Pattern The field of view changes its size as you
16. parameters according to the type of scan engine mounted on the mobile computer For a complete list of parameters and of their configuration procedures please refer to the SDK Help file on the CD IMAGER SCAN PARAMETERS LASER MODELS MODELS 5000 Not available Not available BeepDuration Not available BARCODE SYMBOLOGY IMAGER SPECIFIC READER PARAMETERS APRO MODELS EANS Ci Entec EAN13 fEnabled Disabled Disabled Disabled Disabled Not available EAN128 LEnapied Disabled In the Imager models these codes may only be enabled or disabled as a group by the UPC EAN JAN family selection see a few lines below 43 DATALOGIC MEMOR BARCODE SYMBOLOGY IMAGER MSI LD lsabled Not available Plessey Cd Disabled Not available nabled AR Not available Enabled POSTNET POSTNET Not available PLANET Not available Not available Disabled Australia Post Not available KIX Code Not available Royal Mail Code RM4SCC Not available These codes may be enabled individually but are disabled as a group 44 USE AND FUNCTIONING a 3 6 2 Capture The Data Capture applet Capture enables code reading Data Capture ON jes Save Data To LogFile o El Data Capture Window Data Capture can also be enabled through the Configuration applet by selecting File gt Scanner from the main menu or by enabling the parameter Scan Always On in the Scan Parameters branch E
17. pointer forwards backwards upwards or downwards Press down like the left click of the mouse During a phone call you can set the speaker volume by moving the joystick up and down NOTE 27 ED DATALOGIC MEMOR 3 2 WINDOWS MOBILE WELCOME WIZARD In Windows Mobile at the very first Memor startup following a clean boot or following a registry restore to default values the mobile computer startup see par 3 1 is preceded by the Welcome Wizard Windows Mobile Version 6 Tap the screen to set Up sadi Window s Mobile based devices ratiorm ll fights reserved is protected by U S and Welcome Wizard Screen The Welcome Wizard allows the user to calibrate the touch screen see par 3 7 5 and to configure an email account and a password to protect the terminal align screen Tap the target firmly and accurately at each location on the screen The target will continue to move until the screen is aligned L Touch Screen Calibration Screen 28 USE AND FUNCTIONING a 3 3 DATA CAPTURE To capture data first of all select the barcode icon on the bottom right side of the display and tap the Capture menu item then proceed with the following directions To configure and enable data capture parameters refer to par 3 6 3 3 1 Laser Data Capture To scan barcodes point the Datalogic Memor laser model onto the code from a distance within the reading range while pressing the SCAN key The
18. with the product in question or consult the dedicated section at the website www mobile datalogic com Information aux utilisateurs concernant la Directive Europ enne 2002 96 EC Au terme de sa vie utile le produit qui porte le symbole d un caisson a ordures barr ne doit pas tre limin avec les d chets urbains Eliminer ce produit selon cette Directive permet de xvii viter les retomb es n gatives pour l environnement et la sant d rivant d une limination incorrecte r cup rer les mat riaux dans le but d une conomie importante en termes d nergie et de ressources Pour obtenir des informations compl mentaires concernant l limination veuillez contacter le fournisseur aupr s duquel vous avez achet le produit ou consulter la section consacr e au site Web www mobile datalogic com Informaci n para el usuario de accuerdo con la Directiva Europea 2002 96 CE Al final de su vida til el producto marcado con un simbolo de contenedor de bassura m vil tachado no debe eliminarse junto a los desechos urbanos Eliminar este producto de accuerdo con la Directiva permite de n evitar posibles consecuencias negativas para el medio ambiente y la salud derivadas de una eliminaci n inadecuada recuperar los materiales obteniendo as un ahorro importante de energ a y recursos Para obtener una informaci n m s detallada sobre la eliminaci n por favor p ngase en contacto con el proveedor donde lo compr o
19. working on an ESD mat and ensuring that the operator is properly grounded Do not force the card If you feel resistance remove the card check CAUTION the orientation and reinsert it Do not use the SIM card slot for any other accessories The SIM Card option is not available in 802 11b g radio and batch models INTRODUCTION ED 1 5 1 Removing the SIM Card To remove the SIM card follow the steps above to access the SIM area and remove it from its slot All the basic functionalities normally associated to the SIM card are managed by the terminal GPRS connectivity phone calls SMS handling It is possible that not all the services connected to the SIM card can be used or can be managed by the terminal Db DATALOGIC MEMOR 1 6 ACCESSORIES O Cradles 94A151111 Datalogic Memor Single Cradle 94A151121 Datalogic Memor Powered Vehicle Dock O Batteries 94ACC1368 DL MEMOR Standard Battery CVR2 Li Pol or Li lon battery pack 1000 mAh 3 7 V 94ACC1367 DL MEMOR Large Capacity Battery CVR2 Li Pol or Li lon battery pack 2000 mAh 3 7 V Q Power Supply 94ACC1324 PG5 30P35 AC DC Power Supply EU USA Plug 94ACC1334 PG5 30P35 AUS Plug Adapter 10pcs 94ACC1335 PG5 30P35 UK Plug Adapter 10pcs 94ACC1339 PG5 30P35 EU Plug Adapter 10pcs O Cables 94A051016 CAB 421 Mini USB Straight Cable 94A051022 WIN NET Serial Cable HRS ST40X 18S CV 94A051024 CAB USB Type Standard A 4 pin F to Mini A 5 pin M 94A051
20. 966 CAB Direct Cigarette Lighter Adapter LI Various 94ACC1328 Datalogic Memor Stylus Pens 10 pcs 94ACC1365 Datalogic Memor Headset 94ACC1366 Datalogic Memor Softcase Use only a Datalogic Mobile approved power supply and cables Use of an alternative power supply will invalidate any approval given to this device and may be dangerous NOTE 1 7 OPERATING SYSTEM Datalogic Memor supports two different operating systems Windows CE and Windows Mobile For further information regarding Windows Mobile refer to the website http www microsoft com windowsmobile 10 CONNECTIONS O 2 CONNECTIONS 2 1 USB CONNECTION You can use any standard mini USB cable to directly connect the Datalogic Memor to a host computer to transfer data through the USB interface A Key A Host Computer C Datalogic Memor B Standard Mini USB cable d Connection through the cradle is compliant to 2 0 USB standard NOTE The Single Cradle can be connected to the Host by any standard mini USB cable to transfer data through the USB interface A Key A Host Computer C Single Cradle B Standard Mini USB cable D Power Supply only necessary for battery charging In this case the power supply is only necessary for battery charging Insert the power supply plug into the power jack on the base of the cradle and attach the power supply to a power outlet 11 Eb DATALOGIC MEMOR d Connection through th
21. Buttons To configure the way up down and the rest of keys control repeats use the Up Down Control applet Start gt Settings gt Personal gt Buttons gt Up Down Control d Buttons Windows CE Buttons Icon Windows Mobile Buttons Icon Customize the way your Up Down control repeats Delay before first repeat You can also select to wake up the terminal by the SCAN key To assign desired applications to be launched by one of the keys refer to DFU Reference Guide 47 ED DATALOGIC MEMOR 3 7 2 Registry The REGISTRY ADMIN applet provides management of Windows CE 5 0 Windows Mobile registry From the Windows CE control panel main window select the REGISTRY ADMIN applet by double tapping the Registry Admin icon From the Windows Mobile Start menu tap Settings gt System gt Registry Admin Select the REGISTRY ADMIN applet by tapping the Registry Admin icon The Registry Administration Main wndow appears Two functions are available 5 Save Registry allows permanently saving the Windows configuration example custom configuration of screen desktop background color or network adapter configuration to non volatile memory SAVE button Restore Default Registry allows restoring the initial factory default configuration Restore Default button After restoring the factory default configuration you must perform a warm boot Saving the registry to non volatile memory guarantees the persiste
22. I I Eg I I I 1 i i A 4 Le Lee ee 1_ 4 T o l l l 1 i Zg S e a I I I 1 i i I ua a CO 1 E I I I I i i E s l l 9 i i i i i i i BEL ech ben bebe Li E Se Zi I I cu Ei al colica LO E i I l NS I l ee E ES E SE I SAS v se Klee ee EL i i i E E 1 1 l 12 L J i i TRE SET TAI i les I I EL J i Swe ew ew em ew wm em wm tko k wem e em wm wm emm em em wm em em wm I pole E i Hi I 1 I I les I I I 1 I 1 1 I I 1 1 1 l i I I I I a E E d a 1 I 1 1 1 l I I 1 1 1 i I I 1 1 1 i I I I I I l O O O O O Oo Oo Oo O O O O O O O O St m N og o og N m St A aes ee pP 4 t b 4d 4 be ze ooo rn A E A A mm 1000 1100 1200 mm 0 800 900 70 600 500 84 TEST CODES 6 TEST CODES High Density Codes 0 25 mm 10 mils 17162 0123456784 2 5 Interleaved code 128 TLL test 80 a Ill 8 012345 000012 80 i 6450 9723 85 O DATALOGIC MEMOR Medium Density Codes 0 38 mm 15 mils 17162 0123456784 test 100 UN I Ii 8 012345 000012 100 8 64509723 86 TEST CODES Low Density Codes 0 50 mm 20 mils e ii I Il I I 17162 DS 0123456784 e lll Il test 120 H 8 012345 000012 120 8 64509723 87 O DATALOGIC MEMOR 2D Co
23. Mode KeyboardEmula SoftTrigger ScanAlwaysOn NotPrintableChar Beep wav 200 al Disabled no Enabled Disabled Leave Scanner Setup lt Scan Parameters gt Scanner Setup lt Scan Parameters gt Selecting Data Capture Setup Parameters Alternatively using the stylus you can tap once directly on the value on the right column continue tapping until the desired value is reached To activate a new configuration select the File gt Save Menu to send the new configuration to the barcode decoding software and save the new configuration This will save the configuration to non volatile memory preventing loss at the next system reset 41 ED DATALOGIC MEMOR Reader Parameters The barcode reading parameters and values are dependent upon the type of scanner module mounted in your mobile computer For a detailed list of parameters and of their configuration procedures please refer to the SDK Help file on the CD Scan Parameters The Scan Parameters are common to all scanner modules and allow control of the scanning device The Scan parameters are described as follows ScanTimeout the maximum time in milliseconds during which the scanner remains on without decoding any barcode BeepType if set to dual tone the good read beep is a sequence of high and low pitch sounds If set to monotone the beep is a single pitch sound BeepDuration the time interval in milliseconds during which the beeper will sou
24. N Parameter Window Help Scanner Save Restore Default Export XML Import XML exit Scanner Setup lt Parameters gt Enabling the Data Capture 45 ED DATALOGIC MEMOR 3 7 CONTROL PANEL From the Windows CE Desktop double tap on the My Device icon and then double tap on the Control Panel icon to open the Windows CE control panel main window The Control Panel can also be launched from Start gt Settings gt Control Panel APPLET programs are displayed as icons one icon corresponds to each APPLET Battery Bluetooth Settings Buttons Certificates 2 Datalogic Date Time Deckt u b Decoding Dialing Y saom k AS Windows CE Control Panel From the Windows Mobile Start menu tap Settings A three tab dialog opens Personal System Connections APPLET programs are displayed as icons one icon corresponds to each APPLET SE Settings SE Settings SE Settings Bd DK s x di 8 e H te Input Lock About Backlight Certificates Beam Bluetooth Connections H 8 O A e y Menus Owner Sounds amp Clock amp Customer Datalogic Domain Network USB to PC Information Notifications Alarms Feedback Deskto Enroll Cards DS BS O Device Info Wireless Manager Personal System Connections Cl Personal System Connections a Personal System Connections ul i cm E E Windows Mobile Control Panel 46 USE AND FUNCTIONING a 3 7 1
25. PORT Datalogic Services Warranty Extensions and Maintenance Agreements Authorised Repair Centres CONTACT US E mail form and listing of Datalogic Subsidiaries SAFETY REGULATIONS Read this manual carefully before performing any type of connection to the Datalogic Memor mobile computer The user is responsible for any damages caused by incorrect use of the equipment or by inobservance of the indication supplied in this manual GENERAL SAFETY RULES Use only the components supplied by the manufacturer for the specific Datalogic Memor being used Do not attempt to disassemble the Datalogic Memor mobile computer as it does not contain parts that can be repaired by the user Any tampering will invalidate the warranty When replacing the battery pack or at the end of the operative life of the Datalogic Memor mobile computer disposal must be performed in compliance with the laws in force Before using the devices and the battery packs read par 4 2 Do not submerge the Datalogic Memor M in liquid products For further information refer to this manual and to the Datalogic Mobile web site www mobile datalogic com POWER SUPPLY This device is intended to be connected to a UL Listed CSA Certified computer which supplies power directly to the Datalogic Memor or else be supplied by a UL Listed CSA Certified Power Unit marked Class 2 or LPS power source rated 5 V 3 0 A which su
26. Parameters depend on the type of scanner module installed on the mobile computer and allow barcode configuration i e enable disable Code 39 check digit control etc The Scan Parameters are common to all scanner modules and allow control of the scanning device i e beeper control LED control laser timeout etc Each Data Capture screen window corresponds to a branch of the tree and the name of the current branch is displayed at the bottom of each screen window 40 USE AND FUNCTIONING a File Parameter Window Help Parameter Reader Parame Scan Parameters Scanner Setup lt Parameters gt Data Capture Configuration Window The screen format shows two columns where the left column indicates branches or parameters Branches have three dots in the right column You can navigate through the tree structure using the stylus or keyboard arrows directly on the item field or from the menu Parameters have their corresponding current values in the right column You can edit parameter values using the stylus or keyboard arrows directly on the item field or from the menu To change a value for example select the line of the value to be changed choose Edit from the Parameter Menu then choose a new value from the values listed in the box see following figures File Window Help Value File Parameter Window Help Parameter Value 5000 ScanTimeout 5000 GoodReadSound LedDuration LedPulses Continuous
27. Pat 681 257 B1 789 315 B1 1 128 315 B1 1 396 811 BI Additional patents pending xvi WEEE COMPLIANCE Informazione degli utenti ai sensi della Direttiva Europea 2002 96 EC L apparecchiatura che riporta il simbolo del bidone barrato deve essere smaltita alla fine della sua vita utile separatamente dai rifiuti urbani Smaltire l apparecchiatura in conformita alla presente Direttiva consente di evitare possibili conseguenze negative per l ambiente e per la salute umana che potrebbero invece essere causati dall errato smaltimento dello stesso recuperare materiali di cui composto al fine di ottenere un importante risparmio di energia e di risorse Per maggiori dettagli sulle modalit di smaltimento contattare il Fornitore dal quale stata acquistata l apparecchiatura o consultare la sezione dedicata sul sito www mobile datalogic com Information for the user in accordance with the European Commission Directive 2002 96 EC At the end of its useful life the product marked with the crossed out wheeled wastebin must be disposed of separately from urban waste Disposing of the product according to this Directive avoids potentially negative consequences to the environment and human health which otherwise could be caused by incorrect disposal enables the recovery of materials to obtain a significant savings of energy and resources For more detailed information about disposal contact the supplier that provided you
28. S ROAMING A a ee Se en T Kc MES e gt eee See ll e rl A gt B gt RUMI ETHERNET NETWORK C SITTI APPLICATION SERVER Key A Datalogic Memor B Access Point C Host Application Server 16 CONNECTIONS O 802 11g radio module is on by default in order to avoid wasting energy you can switch it off using the Wireless Communications applet Suspending the terminal powers off the 802 11b g radio and drops the radio connection When the terminal resumes depending on the radio power mode and security protocol selected it may take up to 30 seconds for the 802 11b g radio driver to re associate the radio to the network Area coverage and radio performance may vary due to environmental conditions access points types or interference caused by other devices microwave ovens radio transmitters etc In case of heavy usage the Datalogic Memor could get warm this is normal and does not mean a malfunction 17 2 DATALOGIC MEMOR 2 5 WPAN CONNECTION Datalogic Memor mobile computer models with Bluetooth can communicate with other Bluetooth enabled devices such as a printer within a range of 10 m using the onboard Bluetooth module Key A Datalogic Memor B Bluetooth printer In order to avoid wasting energy the Bluetooth module is off by default If you need to have Bluetooth working the module must be powered on using the Wireless Com
29. Volume Sounds al J Ll Soft Loud Enable sounds for Events warnings system events Applications Notifications Calarms reminders Key clicks sot OMLoud Screen taps sot Loud l REM DECHE Volume amp Sounds Window 57 ED DATALOGIC MEMOR Windows Mobile From the Windows Mobile Start Menu select Settings gt Connections tab and click the Audio icon Settings 5 O SI Certificates Clock E Customer Alarms Feedback u A Datalogic Decoding Device Info Deskto Backlight Audio Window The Audio applet allows to set the recording volumes of the main microphone and of the headset microphone Also it allows to set the headset volume when the user is listening to an audio file SE Audio Settings Pa Ty E ok Microphone Gain Soft Loud Headset Volume Soft Loud Headset Microphone Soft Loud 58 USE AND FUNCTIONING a To set the speaker volume during a call click the icon on the right top of the Windows Mobile Start Menu To set the front speaker or the headset speaker volume use the right bar or move the joystick up and down To set the rear speaker volume use the left bar Start A Cl Wednesday 13 20 January 01 2003 Yolume Phone off Wi Fi Network Card Internet Calling Of Tap here to set owner No unread messages No tasks No upcoming appointm Live Search Device unlocked Getting Started Contacts To set th
30. arry a spare battery pack in your pocket or purse accidental short circuiting can occur when a metallic object such as a coin clip or pen causes direct connection of the contacts of the battery pack these look like metal strips on the battery pack Short circuiting the terminals may damage the battery pack or the connecting object Do not apply voltages to the battery pack contacts Do not pierce the battery pack with nails strike it with a hammer step on it or otherwise subject it to strong impacts or shocks 78 MAINTENANCE O WARNING Do not disassemble or modify i e bend crush or deform the battery pack The battery pack contains safety and protection devices which if damaged may cause the battery pack to generate heat explode or ignite In case of leakage of liquid from the battery avoid contact with liquid the skin or eyes If the contact occurs immediately wash the affected area with water and consult a doctor Do not solder directly onto the battery pack Do not expose the battery pack to liquids Avoid any knocks or excessive vibrations If the device or the battery is dropped especially on a hard surface you should take it to the nearest Authorised Repair Centre for inspection before continuing to use it Do not replace the battery pack when the device is turned on Do not remove or damage the battery pack s label Do not use the battery pack if it is damaged in any part Battery pack usage by c
31. ate see par 3 10 Startup stylus calibration on Windows Mobile When starting the terminal a Welcome Wizard with Stylus Calibration comes up if valid calibration settings are not available This happens in the following circumstances 1 Atthe first startup of the terminal 2 After restoring registry default settings using the applet Registry Admin and performing a boot 3 After a Clean Boot 55 ED DATALOGIC MEMOR 3 7 6 Volume Settings Windows CE From the Windows CE control panel main window select the Audio applet by double tapping the Audio icon Battery Settings H y Bluetooth Buttons Manager Certificates Datalogic Deckt gt N Date Time Decoding a Gh a gt A SS The Audio applet allows to set the recording volumes of the main microphone and of the headset microphone Also it allows to set the headset volume when the user is listening to an audio file Headset Volume Elke Soft Loud Headset Microphone Bia E Soft Loud ee DUD 24 E Audio Window 56 USE AND FUNCTIONING a From the Windows CE control panel main window select the Volume amp Sounds applet by double tapping the Volume Sounds icon La Storage Stylus Manager Terminal Server Clie A Wireless Communic The Volume amp Sounds applet allows to manage the audio features of the rear speaker and appears as follows Volume amp Sounds Pro OK E
32. chnical Features 81 91 Test Codes 85 U USB Connection 11 Using the Joystick 27 Using the Stylus 26 V Volume Settings 56 92 W WEEE Compliance xvii Windows Connections 60 Windows Mobile Bluetooth Manager Device Setup 67 Windows Mobile Phone 71 Windows Mobile Welcome Wizard 28 Wireless and Radio Frequencies Warnings 22 Wireless Communications 51 WLAN Connection 16 WPAN Connections 18 WWAN Connections 19 DATALOGIC www mobile datalogic com World wide Sales Network available from www mobile datalogic com contacts Datalogic Mobile S r l Via S Vitalino 13 40012 Lippo di Calderara di Reno Bologna Italy Telephone 39 051 3147011 Fax 39 051 3147561 822000882 2009 Datalogic Mobile S r l 05 09
33. consultar la secci n dedicada en el Web site www mobile datalogic com Benutzerinformation bez glich Richtlinie 2002 96 EC der europaischen Kommission Am Ende des Ger telebenszyklus darf das Produkt nicht ber den st dtischen Hausmull entsorgt werden Eine entsprechende Mulltrennung ist erforderlich Beseitigung des Produkts entsprechend der Richtlinie verhindert negative Auswirkungen f r die Umwelt und die Gesundheit der Menschen erm glicht die Wiederverwendung der Materialien und spart somit Energie und Resourcen Weitere Informationen zu dieser Richtlinie erhalten sie von ihrem Lieferanten ber den sie das Produkt erworben haben oder besuchen sie unsere Hompage unter www mobile datalogic com xviii CHINA ROHS POLLUTION CONTROL LOGOS Toxic or Hazardous Substances and Elements for DL MEMOR _ Pb Hg Cd Cr PBB PBDE 802 11b g Radio Module O Indicates that this is a toxic or hazardous substance contained in all of the homogenous materials for this part is below the limit requirement in SJ T11363 2006 X Indicates that this is toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ T11363 2006 Note 1 It is only for 944201018 Model Note 2 It is only for 944201015 944201019 944201022 944201018 Models Note 3 Itis only for 944201015 944201019 944201022 Models Note 4 99 of the parts of this product
34. d Registry is restored from persistent memory if a saved copy is available see Registry Applet par 3 7 2 Applications and data stored on file system are preserved A cold boot is 35 ED DATALOGIC MEMOR necessary when the Windows Mobile operating system locks up and the warm boot command does not work To perform a cold boot press and hold the following keys simultaneously Clean Boot A clean boot is a cold boot that causes the device to be restored to a clean configuration The Memor will be reset to its factory configuration only if the user has not installed any additional package Please note that you will lose any applications and data stored in persistent flash memory To perform a clean boot follow these steps 1 Perform a Cold Boot see Cold Boot 2 Quickly release all the keys when the screen goes black 3 Within 1 second press and hold down the Esc and O keys until the left orange led starts blinking 4 Release the Esc and 0 keys 5 Enter 1 to proceed with the Clean Boot sequence Enter 0 to cancel the Clean Boot and proceed with a Cold Boot _ Warm Boot ___ ColdBoot Clean Boot REGISTRY Restored from Restored from Clean configuration no flash flash user config File Preserved Preserved Clean Installation no user System files 36 USE AND FUNCTIONING E 3 5 STATUS INDICATORS 3 5 1 LED Status The Datalogic Memor provides three different LEDs signaling the mobile compute
35. d read RF Radio Frequency RTC Real Time Clock 90 INDEX A Accessories 10 ActiveSync Remote 61 B Backup Directory File Management 73 Bluetooth Manager Device Setup 62 Buttons 47 C Charging the Batteries 74 China RoHS Pollution Control Logos xix Cleaning the Mobile Computer 80 Connection Cables 21 RS232 Direct Connection 21 Connections 11 Connection to USB peripherals 13 Control Panel 46 Conventions v D Data Capture 29 Imager Data Capture 30 Laser Data Capture 29 Data Capture Configuration 40 Datalogic Memor Description 1 Default Settings 43 Description of the Keys 32 F FCC Compliance xv Files Admin 49 Firmware Update for Windows CE 73 FTP Server Setup 72 G General View xx Glossary 89 L Laser Safety vil LED Class xiii Maintenance 74 Micro SD Card Insertion 5 Microsoft ActiveSync 60 Models Description 2 O Operating System 10 P Package Contents 4 Patents xvi R Radio Compliance xiii Reader Parameters 42 Reading Diagram 84 Reference Documentation v References v Registry 48 Replacing the Batteries 76 Resetting the Memor 34 RS232 Connection 15 S Safe Setup 49 Safety Regulations vi SAR Compliance xvi Save Session 49 Scan Parameters 42 Services and Support v SIM Card 7 Special Function Icons 33 Startup 24 Status Indicators 37 Stylus Calibration 53 T Taskbar 38 Te
36. des Datamatrix ECC200 Example Inverse Datamatrix ECC200 Example 88 GLOSSARY Access Point A device that provides transparent access between Ethernet wired networks and IEEE 802 11 interoperable radio equipped mobile units Hand held mobile computers PDAs or other devices equipped with radio cards communicate with wired networks using Access Points AP The mobile unit mobile computer may roam among the APs in the same subnet while maintaining a continuous seamless connection to the wired network Barcode A pattern of variable width bars and spaces which represents numeric or alphanumeric data in binary form The general format of a barcode symbol consists of a leading margin start character data or message character check character if any stop character and trailing margin Within this framework each recognizable symbology uses its own unique format Baud Rate A measure for data transmission speed Bit Binary digit One bit is the basic unit of binary information Generally eight consecutive bits compose one byte of data The pattern of O and 1 values within the byte determines its meaning Bluetooth A standard radio technology using a proprietary protocol The onboard Bluetooth module in the mobile computer is compatible with the 1 1 protocol Byte On an addressable boundary eight adjacent binary digits 0 and 1 combined in a pattern to represent a specific character or numeric value
37. dialog will display different options depending on what type of device you have selected and what service you use e For a printer connection tap the arrow to change the Virtual Port or Delete to remove the device pairing e Tap Sync to initiate a Sync available only if the service is an ActiveSync connection Bluetooth Manager OK x Bluetooth Manager OK x Connections Discovery Settings Connections Discovery Settings Paired Devices double tap to edit Pairing Info Name Device 1 Address 00 02 72 10 D6 BF Service Printer Printer Settings Virtual Port oma y Search for devices AA ES A E a pa Printer 65 ED DATALOGIC MEMOR The icons displayed in the taskbar at the bottom of your Memor a screen will show you the state of the Bluetooth connection as shown in the table below Icon Name _ Description _ Disabled Icon Indicates that Bluetooth has been disabled Unpaired Icon Indicates that the Bluetooth radio is on but the device is currently not paired to another ae Indicates that the Bluetooth radio is on and the device is paired with at least another device A a mn e Bluetooth devices 66 USE AND FUNCTIONING a Windows Mobile Bluetooth Manager Device Setup The Bluetooth Device Properties icon will only be visible if Bluetooth hardware has been installed on the unit Before turning on Bluetooth ensure that the two devic
38. directories of Backup Windows to Windows Likewise to maintain files that must be run at Windows CE 5 0 startup i e exe Ink vb bm etc it is necessary to copy them to the directory Backup Startup This directory does not exist originally only Backup exists and therefore it must be created The application programs will be run after any type of re boot both software and cold boot As an alternative to the Safe Setup function it is possible to copy the cab files to the directory Backup Cabfiles the Cabfiles sub directory doesn t exists originally and must therefore be created and perform a mobile computer cold boot to have the application installed Once these files are copied to the directory Backup Cabfiles the application will be run after each re boot From the second cold boot on a message may be displayed such as lt application name gt is already installed Re install This message blocks the boot process Press the Enter key to continue the system initialization Even if the entire Windows Mobile file system reside in FLASH non volatile memory the mechanism described above is supported also on Windows Mobile for backward compatibility 3 10 FIRMWARE UPDATE The Datalogic Memor is equipped with a tool that implements a firmware update service For further information refer to DFU Reference Guide 73 O DATALOGIC MEMOR 4 MAINTENANCE Rechargeable backup batteries and battery packs ar
39. e Bluetooth headset volume tap Settings gt Connections gt Bluetooth Manager gt Connections and select the headset The following window will appear SE Bluetooth Manag 4 gt Yo d Bluetooth Manager Paired Devices tap to edit Pairing Info Name Bluetooth headset Address 00 10 82 12 B4 E1 Service Headset Audio Settings Volume 59 ED DATALOGIC MEMOR 3 8 WINDOWS CONNECTIONS To connect the Datalogic Memor to another device i e Host PC from Windows several programs are available These programs require specific electrical connections in order to function properly 3 8 1 Microsoft ActiveSync Microsoft ActiveSync gives you the possibility to connect your desktop computer to your Datalogic Memor and synchronize the information on them Synchronization compares the data on the Datalogic Memor with that on the desktop computer and updates both computers with the most recent information With ActiveSync it is possible to Back up and restore Datalogic Memor data Copy files between Datalogic Memor and desktop computer Synchronize files by selecting a synchronization mode You can establish an ActiveSync connection to your Datalogic Memor through the following electrical interfaces USB either directly or through the Single Cradle Bluetooth see par 3 8 2 It is possible to constantly synchronize while connected to a desktop computer or alternative
40. e Memor will search for Bluetooth Devices within range If you attempt to set up a connection when the Bluetooth Radio is disabled you will receive a message reminding you that the radio is turned off and asking you if you want to turn it on Tap Yes if you need to enable the Bluetooth Radio 3 Once searching is complete Bluetooth Device Profiles will be displayed in the Discovery tab You can set up a connection to a device on the list or clear it from the list by tapping the Clear button Bluetooth Manager Ki Connections Discovery Settings Bluetooth Manager ON x Connections Discovery Settings Discovered Devices Connections Discovery settings Discovered Devices Paired Devices double tap to edit Address Searching for al Pocket_PC 00 17 E3 6C EE 75 i Unknown 00 02 72 10 D6 BF VU son Ets Skorpio 00 13 E0 E9 9C D9 Unknown 00 22 FC 75 C0 86 Search for devices a 3 OH Sa 2 Printer Serial All Discover Connect Clear y Gei Re AS y Gei Ren Ae Y ei 7 2 Ae 63 ED DATALOGIC MEMOR To set up a connection 1 From the list of available devices double tap the one you want to activate or select and then tap Connect The resulting dialog will display services that are available on the device Name Skorpio Select a service Modem ASOPP Virtual Port X Authenticate Y Dkm erAS 2 Select the serv
41. e cradle is compliant to 1 1 USB standard NOTE d The actual data transfer speed can be appreciably lower than the maximum theoretical speed NOTE 12 CONNECTIONS O 2 2 CONNECTION TO USB PERIPHERALS You can use a standard A 4 pin female to mini A 5 pin male USB cable to connect the Datalogic Memor to a keyboard or a memory For all these devices maximum current withdrawal must be below 100mA Key A Keyboard with USB interface C 94A051024 Standard A to Mini A USB cable B Datalogic Memor lt a SSA Key A USB hard drive external C 94A051024 Standard A to Mini A memory source USB cable B Datalogic Memor Connect first the USB peripheral to the cable and then the cable to the Datalogic Memor Datalogic Memor works with most of mentioned USB peripherals In any case we can t guarantee good operations with all devices available on market place Connection through the cradle is compliant to 1 1 USB standard 13 O DATALOGIC MEMOR d The actual data transfer speed can be appreciably lower than the maximum theoretical speed NOTE 14 CONNECTIONS O 2 3 RS232 CONNECTION You can use a cable to directly connect the Datalogic Memor to a host computer to transfer data through the RS232 interface A B eee Key A Host Computer C Datalogic Memor B 94A051022 WIN NET HRS ST40X 18S CV The Single Cradle can be connected to the Host by any standa
42. e not initially charged Therefore the initial operation to perform is to charge them See below Annual replacement of rechargeable battery pack avoids possible risks or abnormalities and ensures maximum performance CAUTION 4 1 CHARGING THE BATTERY PACK The battery pack autonomy varies according to many factors such as the frequency of barcode scanning RF usage battery life storage environmental conditions etc NOTE The battery icon on the Taskbar indicates when the battery pack is low It is possible to recharge the battery pack by connecting the power supply directly to the Datalogic Memor M Alternatively it is also possible to recharge the battery pack by using a Single Cradle Moreover recharging is possible by USB Direct connection with the host computer but with longer charging times and in this case it is advised to keep the mobile computer off During the charging process the LED positioned at the right side of the display is red constant Once the charging process has been completed this LED is green constant see par 3 5 If the battery pack is removed from the mobile computer it can be recharged by inserting it into the rear slot of a Single Cradle Do not use the Datalogic Memor until batteries are charged for minimum 4 hours CAUTION 74 MAINTENANCE O Even if the storage temperature range is wider In order to achieve the longest battery life store the terminal and the s
43. ed to execute a system backup to keep your more important files and applications persistent See par 3 9 save the registry to non volatile memory to guarantee CAUTION SE Ee of the Windows configuration See par Windows Mobile There are several reset methods for the Memor A warm boot terminates an unresponsive application and clears the working RAM but preserves the file system Registry are restored from persistent memory if available or returned to factory default A cold boot forces all applications to close reinitializing completely the system lt clears the working RAM but the file system is preserved Registry is restored from persistent memory if available or returned to factory default A clean boot restores the Memor to a clean configuration both the registry and the file system return to a clean status that conform to factory default unless the user has installed an additional package Warm Boot A warm boot closes all applications and clears the working RAM but preserves the file system Registry are restored from persistent memory if a saved copy is available see Registry Applet par 3 7 2 or returned to factory default If an application hangs initiate a warm boot to terminate the application To perform a warm boot press and hold the following keys simultaneously ad Go Cold Boot A cold boot is a complete reset of the Memor in which all applications are forcibly closed and the RAM is completely cleare
44. either installed or portable wireless equipment in the area over the air bag or in the air bag deployment area If vehicle s wireless equipment is WARNING improperly installed and the air bag inflates serious injury could result Turn off the device when in any area with a potentially explosive atmosphere Observe restrictions and follow closely any laws regulations warnings and best practices on the use of radio equipment near fuel storage areas or WARNING distribution fuel areas chemical plants or where some operation involves use of explosive materials Do not store or carry flammable liquids explosive gases or materials with the device or its parts or accessories Areas with a potentially explosive atmosphere are often but not always clearly marked or showed Sparks in such areas could cause an explosion or fire resulting in injury or even death 23 ED DATALOGIC MEMOR 3 USE AND FUNCTIONING The use of the Datalogic Memor depends on the application software loaded However there are several parameters that can be set and utilities that can be used to perform some basic functions such as data capture communications file management etc 3 1 STARTUP The Datalogic Memor turns on when the battery pack or the external supply is inserted After the battery pack is installed use the ON OFF key to turn the mobile computer on and off As soon as the mobile computer is on the Windows CE 5 0 Windows
45. emand contact with field personnel Already well accepted in Retail Windows Mobile and 2D bar code reading capability expand the number of applications Memor tackles into the Pharmacy and emerging applications for produce traceability The computer architecture of the Memor starts with the industry leading XScale PXA310 microprocessor Geared for smart phone computing requirements of real time information management and communication Memory of 128 MB RAM 256 MB Flash is sized for running multiple simultaneous applications for managing large databases or the use of thick applications when off line autonomy is required The memory storage capacity can be increased through the user accessible Micro SD Card Slot The Memor computer architecture can be paired with one of two operating systems Microsoft Windows CE 5 0 with Microsoft WordPad and Internet Explorer 6 0 minimizes the operating system size for faster uploads and more storage space Microsoft Windows Mobile 6 1 reduces training requirements through common Windows interfaces and tools including Outlook Word Mobile Excel Mobile PowerPoint Mobile One Note Mobile and Internet Explorer Mobile 6 0 An open source software development kit SDK aids in creating applications for both of these powerful Windows operating systems and alternative environments like Java Virtual Machine Whether communicating inside or outside the four walls Memor provides voice and data wireless communicati
46. eously COLD BOOT A cold boot is a complete reset of the Memor M in which all applications are forcibly closed and RAM is completely cleared Registry is restored from persistent memory if a saved copy is available see 3 7 2 and RAM file system completely erased You will lose any applications and data registry too which are not stored in persistent flash memory A cold boot is necessary when the Windows CE operating system locks up and the warm boot command does not work To perform a cold boot press these keys simultaneously CLEAN BOOT A clean boot is a cold boot that causes the device to be restored to factory configuration The Memor will reset to its factory configuration clear the working RAM and initialize the file system You will lose any applications and data stored in persistent flash memory At the next startup the system will ask to recalibrate the touch screen To perform a clean boot follow these steps 1 Perform a Cold Boot see Cold Boot 2 Quickly release all the keys when the screen goes black 3 Within 1 second press and hold down the Esc and 0 keys until the left orange led starts blinking 4 Release the Esc and 0 keys 34 USE AND FUNCTIONING a 5 Enter 1 to proceed with the Clean Boot sequence Enter O to cancel the Clean Boot and proceed with a Cold Boot Boot default Backup Folder disk Reinitialized factory default System default Before performing a reset it is recommend
47. es are within close range and that both Bluetooth enabled devices are discoverable 4 Tapping Start gt Settings gt Connections tab gt Bluetooth Manager to open the Bluetooth control panel 5 Tap Settings The Settings tab allows you to enable or disable the Bluetooth radio and specify settings for Incoming Connections 6 Select or clear the Enable Bluetooth Radio check box S Bluetooth Manager amp Yy ff ok Bluetooth Manager Enable Bluetooth Radio Incoming Connection D Encrypt Incoming Connections _ Authenticate None y Port Connections Settings Tap Find Me if you want to make the Memor visible to other Bluetooth devices for 60 seconds allowing them to set up a connection sc Bluetooth Manag Ea Bluetooth Manager Enable Bluetooth Radio Incoming Connection Encrypt Incoming Connections IM Find me ok Discoverable for 60 Seconds 67 ED DATALOGIC MEMOR By default Bluetooth is turned off If you turn it on and then turn off your device Bluetooth also turns off When you turn on your device again Bluetooth turns on automatically To create a Bluetooth partnership between your device and another device that has Bluetooth capabilities ensure that the two devices are turned on discoverable and within close range 2 Open the Bluetooth control panel by tapping Start gt Settings gt Connections tab gt Bluetooth Manager 1 Searc
48. h Manager Device Setup rnrn n 62 Windows Mobile Phone 71 Gi e DEE 72 Backup Directory File Management 73 Firmware RE 73 MAINTENANCE eebe g et Eet a 74 Charging the Battery Pack 74 Replacing the Battery Pack 76 Cleaning the Mobile Computer 80 TECHNICAL FEATURES o occccoococococnnnnnnnennnnnnnnnennnnnnnnnnnnnnnenenenenenennos 81 MSC FING al Data helios 81 O 84 TEST ECO DES nara A A A Sd aes 85 GLOSSAR Va lilla 89 INDEX Licei 91 REFERENCES CONVENTIONS This manual uses the following conventions User refers to anyone using a Datalogic Memor mobile computer Mobile computer and Datalogic Memor M refer to Datalogic Memor mobile computer You refers to the System Administrator or Technical Support person using this manual to install configure operate maintain or troubleshoot a Datalogic Memor mobile computer Single Cradle refers to the Datalogic Memor Single Cradle REFERENCE DOCUMENTATION For further information regarding Datalogic Memor refer to the SDK Help on Line SERVICES AND SUPPORT Datalogic provides several services as well as technical support through its website Log on to www mobile datalogic com and click on the links indicated for further information including PRODUCTS Search through the links to arrive at your product page where you can download specific Manuals and Software amp Utilities SERVICES 8 SUP
49. h for available Bluetooth Devices by tapping the button for the type of device you want Printer Serial or All or tap Discovery to skip this step The Memor will search for Bluetooth Devices within range E Bluetooth Manager Yx ok Bluetooth Manager Paired Devices tap to edit Search for devices Connections Settings Basi E If you attempt to set up a connection when the Bluetooth Radio is disabled you will receive a message reminding you that the radio is turned off and asking you if you want to turn it on Tap Yes if you need to enable the Bluetooth Radio 2 Once searching is complete Bluetooth Device Profiles will be displayed in the Discovery tab You can set up a connection to a device on the list or clear it from the list by tapping the Clear button 68 USE AND FUNCTIONING a 78 BluetoothManager E dh dt DE Bluetooth Manager Discovered Devices 00 04 34 7D 0F 41 00 02 72 10 D6 BF Connections Discovery Settings To set up a connection 1 Double tap the device you want to activate or select and then tap Connect The resulting dialog will display services that are available on the device Bluetooth Manager Bluetooth Manager Create Pairing Name Skorpio Select a service Virtual Port ss O Encryption Authenticate 69 ED DATALOGIC MEMOR 2 Select the service you want to connect to The following table shows the icons that display
50. h stylus holder l headset GSM models only 1 Windows Mobile CE End User License Agreement depending on models Any other packages will contain the accessories necessary for the Datalogic Memor connection to the host computer and to the network the cradle one or more connection cables Remove all the components from their packaging check their integrity and congruity with the packing documents Keep the original packaging for use when sending products to the technical assistance center Damage caused by improper packaging is not covered under the warranty CAUTION Rechargeable battery packs are not initially charged Therefore the initial operation to perform is to charge them See paragraph 4 1 INTRODUCTION o 1 4 INSERTING A MICRO SD CARD Datalogic Memor provides the possibility to add a Micro SD memory storage card To access the Micro SD card slot and insert the card proceed as follows 1 Turn off the Datalogic Memor M 2 Press the latch release button and pull the latch down as indicated in the figure below il a Remove the cover and the battery pack then open the Micro SD card slot by pulling up the locking plate Db DATALOGIC MEMOR b Shift the cardholder to the left and then pull it up insert the Micro SD card with the written part upward C Lock the card into place by pushing the cardholder down and then shifting it to the right pull the locking plate down
51. he following steps 1 Select Start gt Settings gt Control Panel gt Stylus to open the Stylus Properties dialog as shown in Figure 1 2 Adjust Double Tap sensitivity if needed or desired 3 Select the Calibration tab to open the Calibration application Stylus Properties OK Double Tap Calibration Double tap this grid to set the double tap sensitivity for both the speed and physical distance between taps Double tap this icon to test your double tap settings If this icon doesn t change adjust your settings using the grid above Stylus Properties OK Double Tap Calibration If your device isn t H responding properly to your taps YOU may need to recalibrate your screen To start the recalibration process tap Recalibrate Figure 1 4 Tap Recalibrate to open the Calibration screen shown in Figure 2 5 Carefully press and briefly hold stylus on the center of the target Repeat as the target moves around the screen Press the lt ESC gt key to cancel the stylus calibration 6 Press the lt ENTER gt key or tap the screen to accept the new calibration settings Press the lt ESC gt key to keep the old settings 7 New calibration settings are persistently saved in registry 53 ED DATALOGIC MEMOR Carefully press and briefly hold stylus on the center of the target Repeat as the target moves around the screen Press the Esc key to cancel Figure 2 To recalib
52. hildren should be supervised Collect and recycle waste batteries separately from the device in comply with European Directive 2006 66 EC 2002 95 EC 2002 96 EC and subsequent modifications US and China regulatory and others laws and regulations about environment In order to guarantee an adequate operating autonomy when replacing the battery pack the mobile computer checks the battery energy level If the battery is not sufficiently charged Datalogic Memor does not turn on when pressing the ON OFF key In this case either substitute the battery pack with a charged one sufficiently charged or insert Datalogic Memor into a powered cradle or plug it into the direct power supply To achieve the best battery life turn off the radios not in use 79 O DATALOGIC MEMOR 43 CLEANING THE MOBILE COMPUTER Periodically clean the Datalogic Memor with a slightly dampened cloth 80 TECHNICAL FEATURES Eb 5 TECHNICAL FEATURES 5 1 TECHNICAL DATA Datalogic Memor Common Features Electrical Features Power Battery Pack 1 cell Li Pol or Li lon 1100 mAh 3 7 V nominal Alternatively 1 cell Li Pol or Li lon 2000 mAh 3 7 V nominal Internal Backup Battery Rechargeable Ni MH 30 mAh 2 x 15 mAh cells Communication Features Windows CE COM Windows Mobile Port COM Port Serial Interface RS232 COM1 COM1 e a come feoms Wireless Features WLAN IEEE 802 11b g DSSS WPAN Bluetooth IEEE 802 15 Class
53. his manual The battery pack may get hot explode ignite and or cause WARNING serious injury if exposed to abusive conditions If the battery pack is replaced with an improper type there is risk of explosion Do not place the battery pack in or near a fire or heat do not place the battery pack in direct sunlight or use or store the battery pack inside unventilated areas in hot weather do not place the battery pack in microwave ovens dryer high pressure containers on induction cookware or similar device Doing so may cause the battery pack to generate heat explode or ignite Using the battery pack in this manner may also result in a loss of performance and a shortened life expectancy Use only a Datalogic Mobile approved power supply The use of an alternative power supply will void the product warranty may cause product damage and may cause heat explode or ignite The area in which the units are charged should be clear of debris and combustible materials or chemicals Do not use the battery pack of this terminal for power devices different from this mobile computer Immediately discontinue use of the battery pack if while using charging or storing the battery pack the battery pack emits an unusual smell feels hot changes colour or shape or appears abnormal in any other way Do not short circuit the battery pack contacts connecting the positive terminal and negative terminal This might happen for example when you c
54. ice you want to connect to The following table shows the icons that display for different types of service Ceon Bandes Dialup Networking O O OoOO S S S Printer _ File Transfer Protocol FTP Object Exchange OBEX To i SS Object Push OPP Object Exchange OBEX Human Interface Device HID Keyboard Serial Virtual Port allows you to specify the incoming port which is used to communicate serially with an incoming device just as if it were a physical COM port This option is available only if you have selected a Printer or Serial service You can also select Encrypt or Authenticate from the Bluetooth control panel to apply or modify those settings 1 To require Authentication tap the checkbox then tap OK 2 The Authentication Request dialog will then open requesting that you enter a PIN Use the Input Panel to type in the PIN 64 USE AND FUNCTIONING a Authentication A Enter a PIN to authenticate the ll connection Name Skorpio Address 00 13 E0 E9 9C D9 Enter PIN IE Input Panel Esc 1 2 3 4 5 6 7 8 9 0 Tabla w elr t y uli o p Capja s a f a n i k i shirt z x c v binjm 17 cuu DI te J eer MD en 2 3 Tap OK to complete The dialog will also appear when an Authentication request is received from another device Once you have set up a Pairing you can view the settings by double tapping its name from the Connections tab The Pairing info
55. ine Laserdiode Obwohl zur Zeit keine Augenschaden von kurzen Einstrahlungen bekannt sind sollten Sie es vermeiden fur langere Zeit in den Laserstrahl zu schauen genauso wenig wie in starke Lichtquellen z B die Sonne Vermeiden Sie es den Laserstrahl weder gegen die Augen eines Beobachters noch gegen reflektierende Oberflachen zu richten Die Verwendung von Optiksystemen mit diesem Scanner erh ht die Gefahr einer Augenbesch digung Zu optischen Instrumenten geh ren unter anderem Ferngl ser Mikroskope Brillen und Vergr erungsgl ser ACHTUNG FRAN AIS Les informations suivantes sont fournies selon les r gles fix es par les autorit s internationales et se r f rent une correcte utilisation du terminal NORMES DE SECURITE LASER Ce produit est conforme aux normes de s curit laser en vigueur sa date de fabrication CDRH 21 CFR 1040 sous chapitre J et EN 60825 1 2001 Il nest pas n cessaire d ouvrir l appareil pour l installation Putilisation ou l entretien Ne pas essayer d ouvrir ou de r parer les composants de la cavit optique L ouverture de la cavit optique ou la r paration de ses composants par une personne non qualifi e peut entra ner le nonrespect des r gles de ATTENTION s curit relatives au laser Le syst me optique ne peut tre r par OU en usine L utilisation de proc dures ou r glages diff rents de ceux donn s ici peut entra ner une dangereuse exposition lumi re laser v
56. ion des appareils a radio frequence de votre pays pour v rifier d ventuelles restrictions ou licences Pour tout renseignement vous pouvez vous adresser au site web http europa eu int comm enterprise rtte spectr htm DEUTSCH Wenden Sie sich an die fur Radiofrequenzger te zust ndige Beh rde Ihres Landes um zu pr fen ob es Einschr nkungen gibt oder eine Lizenz erforderlich ist Weitere Informationen finden Sie auf der Web Seite http europa eu int comm enterprise rtte spectr htm ESPANOL Contacta la autoridad competente para la gestion de los dispositivos de radio frecuencia de tu pais para verificar cualesquiera restricciones o licencias posibles requerida Ademas se puede encontrar mas informacion en el sitio Web http europa eu int comm enterprise rtte spectr htm xiv FCC COMPLIANCE Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to use the equipment This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference wil
57. iring Tap Sync to initiate a Sync available only if the service is an ActiveSync connection sc Bluetooth Manager Bluetooth Manager Paired Devices tap to edit Device 1 COMO Name Device 1 Address 00 17 E3 6C EE 75 Service Printer Printer Settings Search for devices Virtual Port LLE y Delete Serial All 3 8 3 Windows Mobile Phone For information on Windows Mobile Phone use and functioning refer to the Windows Mobile web site http www microsoft com windowsmobile 71 ED DATALOGIC MEMOR 3 8 4 FTP Server Setup The Datalogic Memor Windows CE Operating System includes a sample File Transfer Protocol FTP server FTP is used for copying files to and from remote computer systems over a network using TCP IP You can establish a connection to your Datalogic Memor using its FTP Server through the following interfaces WLAN using the 802 11b g radio Proceed as follows 1 Create a registry file extension reg to setup and enable FTP Server communication A simple example file for anonymous logon is given below REGEDIT4 HKEY_LOCAL_MACHINE Comm FTPD DefaultDir AllowAnonymousUpload dword 00000001 UseAuthentication dword 00000000 BaseDir XX w TsEnabled dword 00000001 LogSize dword 00001000 DebugOutputMask dword 00000017 DebugOutputChannels dword 00000002 TdleTimeout dword 0000012c Al lowAnonymous dword 00000001 AllowAnonymousVroots
58. isible ATTENTION Le produit utilise une diode laser Aucun dommage aux yeux humains n a t constat la suite d une exposition au rayon laser Eviter de regarder fixement le rayon comme toute autre source lumineuse intense telle que le soleil Eviter aussi de diriger le rayon vers les yeux d un observateur m me travers des surfaces r fl chissantes miroirs par exemple xi L utilisation d instruments optiques avec le scanneur augmente le danger pour les yeux Les instruments optiques comprennent les jumelles les microscopes les lunettes et les verres grossissants ATTENTION ESPA OL Las informaciones siguientes son presentadas en conformidad con las disposiciones de las autoridades internacionales y se refieren al uso correcto del terminal NORMATIVAS EST NDAR PARA LA SEGURIDAD L SER Este aparato resulta conforme a las normativas vigentes de seguridad l ser a la fecha de producci n CDRH 21 CFR 1040 Secci n J y EN 60825 1 2001 No es necesario abrir el aparato para la instalaci n la utilizaci n o la manutenci n No intente abrir o de ninguna manera dar servicio a ninguno de los componentes del recept culo ptico Abrir o dar servicio a las piezas del recept culo ptico por parte del a personal no autorizado podr a ser una violaci n a los ATENCION reglamentos de seguridad El sistema ptico se puede reparar en la f brica solamente La utilizaci n de procedimientos o regulaci
59. l be saved to non volatile memory Backup directory Before doing this it will be checked that the Backup directory has enough space to save the files If the directory space is not enough an error message will be shown and the program will exit the Safe Setup function Two activating procedures are available for Safe Setup 49 ED DATALOGIC MEMOR Select an installation file for example a CAB cabinet file from the Safe Setup mask zj gt profiles gt Program Files 5 Temp G windows Safe Setup First Mask Then select Windows or a relevant sub directory in the path box Then Safe Setup will recognize the new files and directories present in the Windows directory and will copy them to the Backup Windows directory At the next cold boot these files will be restored see par 3 9 Simply skip the first mask either by closing it or by pressing the ESC key When it closes a new mask will pop up it will enable any type of installation even remote ones like ActiveSync installations Make sure the installation directory is Windows or one of its sub directories After installation tap OK Safe Setup will save the new files in the Backup Windows directory z x gt y E Datalogic Date Time Deckt Install your program then press the OK button to make this installation E permanent et 5 Files Admin Input Panel e Safe Setup Second Mask 50
60. l not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC ID U4G0030 for models DL Memor 802 11g BT XV SAR COMPLIANCE This product has been tested and found to comply with the following standards OET BULLETIN 65 SUPPLEMENT C evaluating compliance with FCC guidelines for human exposure to radio frequency electromagnetic fields EN 50360 2001 product standard to demonstrate the compliance of mobile phones with the basic restrictions related to human exposure to electromagnetic fields 300 MHz 3 GHz EN 62311 2008 assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields 0 Hz 300 GHz PATENTS This product is covered by one or more of the following patents Design Pat AU 310182 S CN 658612 HK 0601962 6 KR 30 0466667 JP 1325117 TW D118829 US D574 830 S US Pat 5 992 740 6 808 114 B1 6 997 385 B2 7 387 246 B2 European
61. l raggio laser cos come si eviterebbe qualsiasi altra sorgente di luminosit intensa ad esempio il sole Evitare inoltre di dirigere il raggio laser negli occhi di un osservatore anche attraverso superfici riflettenti come gli specchi Luso di strumenti ottici assieme allo scanner pu aumentare il pericolo di danno agli occhi Tali strumenti ottici includono cannocchiali microscopi occhiali e lenti di ingrandimento ATTENZIONE DEUTSCH Die folgenden Informationen stimmen mit den Sicherheitshinweisen berein die von internationalen Beh rden auferlegt wurden und sie beziehen sich auf den korrekten Gebrauch vom Terminal NORM FUR DIE LASERSICHERHEIT Dies Produkt entspricht am Tag der Herstellung den g ltigen EN 60825 1 2001 und CDRH 21 CFR 1040 Subchapter J Normen f r die Lasersicherheit Es ist nicht notwendig das Ger t wegen Betrieb oder Installations und Wartungs Arbeiten zu ffnen Unter keinen Umst nden darf versucht werden die Komponenten im Optikhohiraum zu ffnen oder auf irgendwelche andere Weise zu warten Das Offnen bzw Warten der Komponenten im Optikhohlraum durch ACHTUNG unbefugtes Personal verst t gegen die Laser Sicherheitsbestimmungen Das Optiksystem darf nur werkseitig repariert werden Jegliche Anderungen am Ger t sowie Vorgehensweisen die nicht in dieser Betriebsanleitung beschrieben werden k nnen ein gefahrliches Laserlicht verursachen ACHTUNG Der Produkt benutzt e
62. ly synchronization can be performed only when the synchronize command is chosen You can select which information types are synchronized and control how much data is synchronized By default ActiveSync does not automatically synchronize all types of information Use ActiveSync options to turn synchronization on and off for specific information types For example Synchronize Microsoft Word and Microsoft Excel files between the Datalogic Memor and the desktop computer The files will automatically be converted to the correct format In Windows Mobile before using the ActiveSync follow the directions described in par 2 3 60 USE AND FUNCTIONING a Visit the following Microsoft Web site for the latest in updates and technical information http www microsoft com windowsmobile activesync default mspx ActiveSync Remote Microsoft ActiveSynce Remote is no longer supported in Windows CE For backward compatibility you can download it from the Internet We suggest enabling the FTP Server and connecting to an FTP Client See par 3 8 4 61 ED DATALOGIC MEMOR 3 8 2 Bluetooth Manager Device Setup Windows CE Bluetooth Manager Device Setup Before turning on Bluetooth ensure that the two devices are within close range and that both Bluetooth enabled devices are discoverable 1 Open the Bluetooth control panel by tapping Start gt Settings gt Connections tab gt Bluetooth Manager
63. move the reader closer or farther away from the code The field of view indicated by the aiming system pattern will be smaller when the Datalogic Memor Imager is closer to the code and larger when it is farther from the code Symbologies with smaller bars or elements mil size should be read closer to the unit Symbologies with larger bars or elements mil size should be read farther from the unit See par 5 1 for further details If the scan has taken place correctly the Good Read LED gets constant Green for a configurable time if enabled the GoodReadSound emits an acoustic signal 31 32 ED DATALOGIC MEMOR 3 4 DESCRIPTION OF THE KEYS The Datalogic Memor provides a 23 key alphanumeric keyboard ON OFF key joystick The following image shows this keyboard USE AND FUNCTIONING a Main Keys Function KEY FUNCTION It starts barcode data capture The joystick lets you move forwards backwards upwards or downwards scroll through a Menu list browse among folder files or select functions if pressed down It can work in two functioning modes Arrow Keys Mode and Mouse Mode It s possible to switch between them by pressing blue modifier BKSP keys in sequence see par 3 1 2 Yellow modifier when pressed before a standard key it enables the character or function printed in yellow above the key Blue modifier when pressed before a standard key it enables the character or function prin
64. munications applet see par 3 7 4 and perform the Discovery procedure see par 3 8 2 Suspending the terminal powers off the Bluetooth radio and drops the piconet Bluetooth connection When the terminal resumes it takes approximately 10 seconds for the Bluetooth radio driver to re initialize the radio Area coverage and Bluetooth radio performance may vary due to environmental conditions or interference caused by other devices microwave ovens radio transmitters etc etc 18 CONNECTIONS 2 6 WWAN CONNECTION Datalogic Memor GSM models enhance your connectivity solutions giving you an opening to an international wireless infrastructure that is the global standard GSM Global System for Mobile communications is a digital mobile phone system based on TDMA it utilizes the 850 900 1800 and 1900 MHz bands In order to use a WWAN Connection you have to install a SIM Card see instructions on par 1 5 In order to avoid wasting energy the GSM module is off by default If you need to have GSM working the module must be powered on using the Wireless Communications applet see par 3 7 4 Suspending the terminal powers off the GSM radio and drops the connection When the terminal resumes if the connection was managed by Microsoft Internet Explorer it is automatically restored otherwise the radio connection must be manually re initialized The GSM voice capability of this mobile computer has
65. nce of the Windows configuration in case of battery pack replacement cold boot or warm boot on Windows Mobile File View F x Remove Storage Programs Manager ES Registry Administration Window 48 USE AND FUNCTIONING a 3 7 3 Files Admin The FILES ADMIN applet enables control of the permanence of files in the Windows CE System Folder Because Windows Mobile mounts the entire file system in persistent store rather than using RAM it provides both users and applications with a reliable storage platform even in the absence of battery power The FILES ADMIN applet is therefore not necessary Two functions are available on the Files Admin Main window by means of two buttons 2 AD Datalogic Date Time Files Admin Input Panel E 9 Files Admin Main Window Save Session with this button all files will be permanently saved in the Windows directory in non volatile memory This function guarantees the steady maintenance of every file produced during the current working session even of sub directories and relevant files with the exception of the files belonging to the FLASH image These current working session files will be backed up in the Backup Windows directory At the next cold boot the files previously saved in the Backup Windows directory will be restored to the Windows directory see par 3 9 Safe Setup with this button the installation of software programs wil
66. nd when the scanner reads a code To disable the beeper set this value to 0 BeepFrequency determines the frequency in Hertz of the beeper GoodReadSound is the beep sound emitted when the scanner reads a code LedDuration the length of the good read led pulse in milliseconds LedPulses the number of times the good read led pulse is emitted when the scanner reads a code ContinuousMode disables the effect of the ScanTimeout parameter KeyboardEmulation if enabled all scanned data are transformed into keyboard events and can therefore be displayed and saved to a file as if input from the mobile computer keyboard SoftTrigger when enabled the laser can be turned on off by the application software ScanAlwaysOn enables the scanner for barcode reading independently from the application software GreenSpotDuration determines the duration measured in milliseconds of the green spot feedback which provides a good read green dot directly on the code where the operator usually tends to be looking NotPrintableChar if set to Remove all not printable characters included in the scanned data are deleted and the final barcode will include only printable characters ScanButton enables disables the scan button If the scan button is disabled the reader can be triggered under software control 42 USE AND FUNCTIONING E Default Settings The following tables contain the default values for the major barcode setup
67. on options to meet the business need A GSM radio using Edge data compression provides a broadband cellular connection for real time data transactions in the field A speaker and microphone equip the Memor to handle traditional phone calls Inside the four walls the Summit IEEE 802 11b g radio s optimized transmit power and receiver sensitivity result in superior range with a tailored user interface for easy configuration and consistent management Complimented by a CCX v4 security certification from Cisco the Memor provides infrastructure compatibility focused on enterprise requirements for encrypted communication and seamless roaming Client side applications leverage internet protocol connections for hands free voice picking and push to talk communications Bluetooth Wireless Technology connects headsets printers and other peripherals while eliminating cumbersome wires and costly replacement of broken or damaged cables Two scanner options optimize the Memor for the application needs A laser scanner tackles intensive applications where speed and a wide depth of field Ge DATALOGIC MEMOR are essential Datalogic s patented Green Spot good read feedback makes Memor s laser scanner intuitive while reducing errors The 2D scan engine option leverages picture technology to capture a wide range of Linear Stacked and 2D codes while also providing the flexibility to capture a signatures or drivers license Digital image decoding software red
68. ones diferentes de aquellas describidas en la documentaci n puede causar una exposici n peligrosa a la luz l ser visible ATENCI N El aparato utiliza un diodo l ser a baja potencia No son notorios da os a los ojos humanos a consecuencia de una exposici n de corta duraci n Eviten de mirar fijo el rayo l ser as como evitar an cualquiera otra fuente de luminosidad intensa por ejemplo el sol Adem s eviten de dirigir el rayo l ser hacia los ojos de un observador tambi n a trav s de superficies reflectantes como los espejos El uso de sistemas pticos con el esc ner aumentar el riesgo de da os oculares Los instrumentos pticos incluyen binoculares microscopios lentes y lupas ATENCI N xii LED CLASS According to EN60825 1 2001 the Datalogic Memor 1D models which use the green spot LED are also CLASS 1 LED PRODUCTS APPARECCHIO LED CLASSE 1 IEC PRODUIT LED DE CLASSE 1 IEC PRODUKT LED KLASSE 1 IEC PRODUCTO LED DE CLASE 1 IEC According to EN60825 1 2001 the Datalogic Memor 2D models which use the illuminator LED are also CLASS 1M LED PRODUCTS LED LIGHT LUCE LED DO NOT VIEW DIRECTLY NON OSSERVARE DIRETTAMENTE WITH OPTICAL INSTRUMENTS CON STRUMENTI OTTICI CLASS 1M LED PRODUCT APPARECCHIO LED DI CLASSE 1M LAMPE LED LUZ LED NE PAS OBSERVER DIRECTEMENT NO OBSERVAR DIRECTAMENTE AVEC INSTRUMENTS OPTIQUES CON INSTRUMENTOS OPTICOS APPAREIL LED DE CLASSE 1M PRODUCTO LED DE CLASE 1M LED LICHT
69. options laser imager e compute options O S version For further details about the Datalogic Memor models refer to the web site http www mobile datalogic com The currently available models are e 944201016 DL Memor Batch 1DGS CE5 Datalogic Memor Batch 128MB RAM 256MB Flash 23 key Numeric Std Laser with Green Spot CE 5 0 e 944201019 DL Memor 802 11g BT 1DGS CE5 Datalogic Memor 802 11b g CCX V4 Bluetooth 128MB RAM 256MB Flash 23 key Numeric Std Laser with Green Spot CE 5 0 e 944201022 DL Memor 802 11g BT 2D CE5 Datalogic Memor 802 11b g CCX V4 Bluetooth 128MB RAM 256MB Flash 23 key Numeric Std 2D Imager CE 5 0 INTRODUCTION Gp 944201015 DL Memor 802 119 BT 2D WM6 1 Datalogic Memor 802 11b g CCX V4 Bluetooth 128MB RAM 256MB Flash 23 key Numeric Std 2D Imager WM 6 1 944201018 DL Memor EdgeE BT 2D WM6 1 Datalogic Memor Edge Europe Bluetooth 128MB RAM 256MB Flash 23 key Numeric Std 2D Imager WM 6 1 Db DATALOGIC MEMOR 1 3 PACKAGE CONTENTS The Datalogic Memor package contains Datalogic Memor mobile computer l AC DC power supply l EU plug adapter AUS Plug Adapter UK Plug Adapter standard Mini USB cable l l l i i mb CD ROM Datalogic SDK CD ROM Getting Started Disk only for Windows Mobile l l extensible stylus l users manual l rechargeable standard battery pack cover l hand strap wit
70. pare batteries between 20 to 30 C 68 to 86 F The Batteries must be charged at a temperature ranging from 0 to 40 C 32 to 104 F For the GSM models the maximum recommended temperature is 35 C At higher values the charging may slow down The battery level may not be displayed correctly for some minutes after the disconnection if the Datalogic Memor is disconnected from power supply before the charging cycle is completed The Datalogic Memor could get warm during charging this is normal and does not mean a malfunction Use only a USB IF compliant USB port as a charging source 75 O DATALOGIC MEMOR 4 2 REPLACING THE BATTERY PACK To correctly replace the battery pack proceed as follows 1 Turn off the Datalogic Memor 2 Press the latch release button and pull the battery latch down as indicated in the figure below 3 Remove the cover and the battery pack Install the new battery pack first insert the bottom contacts side then the upper side as indicated in the following figure 4 5 Press the latch release button and pull the battery latch down to reinsert the cover 76 MAINTENANCE O As the battery cover is lifted the mobile computer automatically shuts off in order to retain data during the pack substitution CAUTION TT O DATALOGIC MEMOR Installing charging and or any other action should be done by authorized personnel and following t
71. pplies power directly to the Datalogic Memor via the power connector of the cable The package includes three international plug adapters The adapters must be plugged in the power supply before the power supply itself is plugged on the wall outlet vi LASER SAFETY The laser light is visible to the human eye and is emitted from the window indicated in the figure This information applies to both laser models and the Datalogic Memor Imager Aiming System Laser output window This product complies with 21 CFR Subchapter J CLASS 1 LED PRODUCT Mod DL MEMOR p 944201016 Sage be o UR H FE Agen 3 40007 Gites d eco ODC Be Made in Tanran Mod DL MEMOR pn 94420101 tuten via AHA Datalogic Mobile S r l via S Vitalino 13 40012 Calderara S N POSDOOOO1 di Reno BO Italy Made in Taiwan vii La luce laser Die Laserstrahlung Le rayon laser est La luz laser es visibile all occhio ist fur das visible a l oeil nu et il visible al ojo umano e viene menschliche Auge est mis par la humano y es emessa dalla sichtbar und wird am fen tre d sign e sur emitida por la finestra indicata Strahlaustrittsfenster l illustration dans la ventana indicada nella figura ausgesendet siehe figure en la figura Bild LUCE LASER LASERSTRAHLUNG RAYON LASER RAYO LASER NON FISSARE IL NICHT IN DER STRAHL EVITER DE NO MIRAR FIJO EL FASCIO BLINKEN REGARDER RAYO APPARECCHIO PRODUKT DER LE RAYON APARATO LASER DE
72. r other medical devices to follow the same recommendations provided by Health Industry Manufacturers Associations for mobile phones WARNING Persons with pacemakers e Should ALWAYS keep this device more than twenty five 25 cm from their pacemaker and or any other medical device Should not carry this device in a breast pocket Should keep the device at the opposite side of the pacemaker and or any other medical device Should turn this device OFF or move it immediately AWAY if there is any reason to suspect that interference is taking place Should ALWAYS read pacemaker or any other medical device guides or should consult the manufacturer of the medical device to determine if it is adequately shielded from external RF energy In case of doubt concerning the use of wireless devices with an implanted medical device contact your doctor Turn this device OFF in health care facilities when any regulations posted in these areas instruct you to do so Hospitals or health care facilities may use equipment that WARNING could be sensitive to external RF energy RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles Check with the manufacturer or its representative regarding your vehicle You should also WARNING consult the manufacturer of any equipment that has been added to your vehicle 22 CONNECTIONS DO An air bag inflates with great force DO NOT place objects including
73. r status Good Read and It is constant for a configurable time General Purpose to signal that a successful read has left side occurred Green Red It is also available to the application program Charging Status Green constant It is constant once the charging right side process has been completed Red constant It is constant while charging 37 ED DATALOGIC MEMOR 3 5 2 Taskbar The Taskbar provides information about the time the battery level the keyboard function and the decoding status ICONS DESCRIPTION Time and Battery Icons In Windows CE they are representative of five different icons indicating the battery level The icon is partially green when the power left is gt 20 and partially red colored when the power left is lt 20 In Windows Mobile it displays the system battery Status It indicates that the battery is charging Windows CE lt indicates that the battery is charging Windows Mobile Keyboard Status Icons i It indicates that the blue FUNC key has been pressed Fun and is going to affect the next key press It indicates that the yellow FUNC key has been pressed and is going to affect the next key press It indicates that the ALPHA key has enabled the selection of the characters printed in orange It indicates the NUMERIC key selection the ALPHA key has not been pressed It indicates that the ALPHA key has enabled the selection of the characters printed in orange and
74. rate the touch screen on Windows Mobile complete the following steps 1 Select Start gt Settings gt System gt Screen to open the Screen Settings dialog as shown in Figure 3 Settings Screen Orientation GC Portrait I Landscape right handed Landscape left handed Align Screen Align the screen if it is not responding accurately to stylus kaps Align Screen General ClearType Figure 3 2 Tap Align Screen to open the Calibration screen shown in Figure 4 3 Carefully press and briefly hold stylus on the center of the target Repeat as the target moves around the screen Press the lt ESC gt key at any time to cancel the stylus calibration 4 By completing the calibration procedure you implicitly accept the new calibration settings 5 New calibration settings are persistently saved in registry 54 USE AND FUNCTIONING a pp align screen Tap the target firmly and accurately at each location on the screen The target will continue to move until the screen is aligned Figure 4 Startup stylus calibration on Windows CE When starting the terminal a stylus calibration screen comes up if valid calibration settings are not available This happens in the following circumstances 1 Atthe first startup of the terminal 2 After restoring registry default settings using the applet Registry Admin and performing a warm boot 3 After a Clean Boot 4 After a Firmware Upd
75. rd 9 pin serial null modem cable for RS232 communications Once the Host has been turned on insert the Datalogic Memor mobile computer into the cradle A Key D A Host Computer C Single Cradle B 94A051020 CAB 427 D Power Supply only necessary for Null Modem battery charging In this case the power supply is only necessary for battery charging Insert the power supply plug into the power jack on the base of the cradle and attach the power supply to a power outlet If the mobile computer supports Windows Mobile before plugging the RS232 cable you have to check the COM1 Enable option on the System Configuration window Start gt Programs gt System Configuration CAUTION 15 DATALOGIC MEMOR 2 4 WLAN CONNECTION Datalogic Memor 802 11b g radio models can communicate with the host using the on board radio frequency component and an Access Point connected to the host computer For models using the 802 11g radio you can find information about the applet for radio configuration http www summitdatacom com SCU htm To launch this utility you can tap the specific icon if it s visible on the taskbar or 1 On Windows CE devices you can open Connections folder or Control Panel from desktop and select the Summit Client Utility icon 2 On Windows Mobile devices you can select the menu item Start gt Programs gt Summit and tap the Summit Client Utility icon SEAMLES
76. ted in blue above the key Tam It powers the Datalogic Memor ON or OFF It is placed on the upper left side of the terminal The ALPHA key is used to alternate numeric and alphanumeric use of the 10 numeric keys Special Function Icons ICON FUNCTION After a yellow modifier key press it opens the Start menu After a yellow modifier key press it opens the file manager A After a yellow modifier key press it switches ON OFF the 0 display backlight 0 After a blue modifier key press it switches ON OFF the 1 keyboard backlight B After a blue modifier key press it locks and unlocks the keyboard 33 ED DATALOGIC MEMOR 3 4 1 Resetting the Memor Windows CE There are several reset methods for the Memor M A warm boot terminates an unresponsive application and clears the working RAM but preserves both the file system and the registry A cold boot forces all applications to close and clears working RAM and files not resident on the persistent flash memory Registry is restored from persistent memory if available or returned to factory default A Clean Boot restores the Memor to factory configuration registry and file system return to factory default WARM BOOT A warm boot closes all applications clears the working RAM but preserves the file system and registry If an application hangs initiate a warm boot to terminate the application To perform a warm boot press these keys simultan
77. the Capslock is active It indicates that the keyboard is locked Decoding Status It indicates that the decoder is active green not active grey 38 USE AND FUNCTIONING a A aus ak Windows CE Taskbar eo de ES Windows Mobile Taskbars 39 ED DATALOGIC MEMOR 3 6 DATA CAPTURE CONFIGURATION From the Windows CE Taskbar tap the Decoding icon to open a drop down menu Decoding can also be accessed from the Control Panel By selecting the nfo item from this drop down menu you can access information about the Scanner and the Software the Configure item opens the configuration applet Data Capture Configuration Window while Capture accesses the data capture applet Data Capture Window which enables code reading The last menu item Wedge enables Wedge Emulation From the Windows Mobile Start menu tap Settings gt System gt Decoding The Decoding icon opens the configuration applet Data Capture Configuration Window Settings Clock E Customer Datalogic Alarms Feedback Deskto Device Info Encryption E sul Error External Managed Reporting Programs Info Configure Capture Sade i System KI 24M sm AS Windows CE Windows Mobile 3 6 1 Configure The Configuration applet contains the barcode scanning configuration parameters in a directory tree structure The available barcode parameters are divided into two groups Reader Parameters and Scan Parameters The Reader
78. tiple items Double Tap Tap and hold the stylus on an item to see a list of actions available for that item On the pop up menu that appears tap the action you want to perform To recalibrate the touch screen use the Stylus Applet see par 3 7 5 Use only original Datalogic styluses supplied with the product itself harsh applications use of screen protectors CAUTION should be taken into consideration in order to extend the touch screen operating life To prevent damage to the screen do not use sharp devices or any device other than the Datalogic Mobile provided stylus Do not apply not necessary high pressures on the screen For applications where an intensive use of the touch screen is foreseen please consider that touch screen components are subject to progressive wear 26 USE AND FUNCTIONING a 3 1 2 Using the Joystick The joystick selects items and enters information The joystick can work like the directional arrow keys of a PC keyboard or can function like a mouse and control the mouse pointer It is possible to switch between the two functioning modes by pressing blue modifier BKSP keys in sequence Arrow Keys Mode Move in the four directions move forwards backwards default upwards or downwards within text fields scroll through a Menu list or browse among folder files Press down selects the current function like the Enter key Mouse Mode Move in the four directions move the mouse
79. to be addressed to occasional use in well covered areas If the coverage is poor the voice quality can be highly affected Calls can be made or received using the Datalogic Memor as a phone handset by the Datalogic Memor headset or by a Bluetooth headset the SIM Card option is not available in 802 11g radio and batch models 19 lt lt DATALOGIC MEMOR During a call you can set the speaker volume by moving the joystick up and down In case of heavy usage the Datalogic Memor could get warm this is normal and does not mean a malfunction NOTE 20 CONNECTIONS O 2 7 CONNECTION CABLES O RS232 Direct Connection 94A051022 WIN NET SERIAL CAB HRS ST40x 18S CV Datalogic Memor HOST PC side side G 3 9 pin female EE 2 CTS RTS _ K _ _ _ _ _ _ ____ 1 RTS CTS E ig DSR 13 DCD DTR 15 4 DTR DCD 14 1 DSR 6 R E RI GND GND 7 5 Q Power Supply Polarity VEXT GND 21 2 DATALOGIC MEMOR 2 8 WIRELESS AND RADIO FREQUENCIES WARNINGS Use only the supplied or an approved replacement antenna Unauthorized antennas modifications or attachments could damage the product and may violate WARNING laws and regulations Most modern electronic equipment is shielded from RF signals However certain electronic equipment may not be shielded against the RF signals generated by TM WARNING Datalogic Memor Datalogic recommends persons with pacemakers o
80. uces failed reads due to damaged and poor quality barcodes while enabling the user to scan from almost any orientation Durability ratings protect the computing investment against accidental drops and occasional exposure to liquids and dust A touch color display provides an easy to read interface in a wide range of lighting conditions The phone keyboard layout and four direction joystick increase associate efficiency Push button battery lock provides an easy to locking mechanism for quick no hassle battery exchanges Rechargeable Lithium polymer batteries in two sizes customize capacity to the application Charging cradles include a communication cradles for RS232 and USB A powered vehicle dock and cigarette lighter adapter extend charging capabilities onto the road Powered by Wavelink device maintenance and management tools makes the Memor a simple device to both deploy and maintain Datalogic Firmware Desktop and Configuration Utilities complete the package with unprecedented ability to customize device configuration to the use environment or process Combined these tools streamline deployment and management activities while providing developer tools to further customize units for specific applications 1 2 MODELS DESCRIPTION The brand new Datalogic Memor is available in different models depending on the options it is equipped with All options are listed below e communication options 802 11b g radio Bluetooth GSM e capture
81. uld with any very strong light source such as the sun Avoid that the laser beam hits the eye of an observer even through reflective surfaces such as mirrors etc Use of optical systems with the scanner will increase eye hazard Optical instruments include binoculars microscopes eye glasses and magnifying glasses CAUTION ITALIANO Le seguenti informazioni vengono fornite dietro direttive delle autorit internazionali e si riferiscono all uso corretto del terminale NORMATIVE STANDARD PER LA SICUREZZA LASER Questo prodotto risulta conforme alle normative vigenti sulla sicurezza laser alla data di produzione CDRH 21 CFR 1040 sezione J e EN 60825 1 2001 Non si rende mai necessario aprire l apparecchio per motivi di installazione utilizzo o manutenzione Non tentare di accedere allo scomparto contenete i componenti ottici o di farne la manutenzione L apertura dello scomparto o la manutenzione di ATTENZIONE qualsiasi parte ottica da parte di personale non autorizzato potrebbe violare le norme della sicurezza Il sistema ottico pu essere riparato solamente alla fabbrica L utilizzo di procedure o regolazioni differenti da quelle descritte nella documentazione pu provocare un esposizione pericolosa a luce laser visibile ATTENZIONE Il prodotto utilizza un diodo laser a bassa potenza Sebbene non siano noti danni riportati dall occhio umano in seguito ad una esposizione di breve durata evitare di fissare i

Datalogic Memor™ User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents

Datalogic Memor&trade; User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents

Datalogic Memor™ User's Manual